MCLX HX. Spiral Pump(Mechanical Seal Type) Mold Temperature Controller. Summary. Performance Curve. Lift

Size: px

Start display at page:

Download "MCLX HX. Spiral Pump(Mechanical Seal Type) Mold Temperature Controller. Summary. Performance Curve. Lift"

Jeffrey Parker
6 years ago
Views:

MCLX HX Mold Spiral (Mechanical Seal Type) Summary MCLX/MCHX promotes stable mold temperature control and high level of safety for large flow rate.

1 MCLX HX Mold Spiral (Mechanical Seal Type) Summary MCLX/MCHX promotes stable mold temperature control and high level of safety for large flow rate. Lift Performance Curve Features SSR allows high precision in temperature control and drastic reduction of maintenance cost. High Precision~Geared for high-precision molding~ Temperature is reflected on monitors with up to 0.1degrees precision. High-Reliability Uses Control Circuit with SSR (non-contact relay), floatless switch without moveable parts. Flow Rate (NOTE) Characteristics of water at normal temperature of 25 C. Safety Precautions Upon excessive heating, power will be automatically shut down. Alarm signal connector (Options) Other options available for further safety precautions.

2 PV SV FOR SETTING ALARM MONITOR RESET ON/OFF PV SV SFT DWN UP ENT Operating Status Alarm Before Maintenance Ensures higher accuracy in temperature control and high level of safety during operation. Reminders for periodical maintenance and other maintenance items can be easily set. Temp Display/Setting: Temp Controller: Input: Memory: Timer: LCD Message Display: Digital Display/Setting Heating & Cooling PID Control SV1 SV2 099hrs. 59min.(Turns ON After Setting) Operation Status Alarm Periodical Maintenance Features Motor Mechanical Seal Impeller Casing High pressure and large flow rate type pump with improved performance/reliability is used. Customized mechanical seal increases shaft seal capacity and expands life-span of pump to allow operation in higher water temperature than other company models structure to resist water residue (Impeller : Stainless steel)

3 Flow Diagram MCLX-Series Strainer Cooling Solenoid Valve Thermostat for Overheat Prevention Water Level Gauge(Electric Rod) Open Relief Valve Medium Return Valve Medium Return Port MCHX-Series Thermostat for Overheat Prevention Water Level Gauge(Electric Rod) Strainer Cooling Solenoid Valve Water Drain Solenoid Valve Water Supply Solenoid Valve Open Relief Valve Relief Valve Medium Return Valve Medium Return Port MCHX-PDD-Series Strainer Relief Valve Reducing Valve Water Drain Solenoid Valve Water Level Gauge(Electric Rod) Thermostat for Overheat Prevention Open Relief Valve Medium Return Valve Medium Return Port Outer Dimension MCLX HX Breaker unit:mm Control Panel Medium Return Port Caster Power Cord Drain Port Model Medium Return Port Drain Port 14-1/2BHose Nipple +Strainer 14-1/2BHose Nipple 1-1/4B Gate Valve 1-1/2B Gate Valve 1-1/4B Gate Valve 1-1/2B Gate Valve 3/8B Plug

4 Standard Specifications Model Power Supply Voltage Apparent Power Breaker Capacity Water Supply Flow Rate Pressure Medium Operational Temperature Range Cooling Capacity Capacity Volume Maximum Circulation Flow Rate Output Cooling Method Water Level Detector Input Control Panel Product Weight Unit 3Phase Clean Water(Soft Water) 10 C Above Water Supply Temperature to 95 C Direct Cooling Floatless Swich NOTE2 Standard for Water Supply Pressure Setting Temperature Water Supply Pressure (NOTE1) 1. Operating temperature range may vary according to supply water temperature. 2. head depends on specific gravity and viscosity of medium used. 3. Models operate at 50Hz and 60Hz cycles. (It cannot be used in an area of different cycle) 4. For product improvement, specifications in this catalog may be changed without prior notice. 5. Mechanical seal may produce slight leakage of water. 6. L and H type controllers with floatless switch cannot be used with distilled water, pure water and high-purity water. For details, please contact to Matsui sales office. 7. In the case that the drainage is being exposed, maximum temperature of MCL Series is 85 C due to pump cavitation. 8. Hose is option. The cooling capacity has cooling water temperature in 18 C. In the medium temperature that L type is 50 C, H,type 100 C. Cooling capacity is subject to cooling water temperature/pressure, medium temperature and circulation flow. The change of water supply pressure causes damage in pump and float switch, etc. Be sure to keep stable pressure for primary side water supply. When the water supply quantity is lacking, the cooling operation is sometimes decompressed by the lacking for water supply. The supply water flow must be more than above chart. When the water supply pipe is narrow and it's distance is long, the cooling operation is sometimes decompressed by the lacking for water supply. Please use pipe diameter for large size. << Reference >> In less than 2 m: 3/8B (Internal diameter 12) In less than 5 m: 1/2B (Internal diameter 15) Adjust the drain side pressure power to about MPa. When the water supply pressure is low, install available separately pressure pump, etc. When the water supply pressure is high, use the pressure release valve, etc. Be sure to install appropriately scale pressure gauge in primary side water supply pipe and drain pipe. Water supply side: MPa(1.6MPa) Drain side: MPa

5 Standard Specifications Model Unit Power Supply Water Supply Medium Voltage Apparent Power Breaker Capacity Flow Rate Pressure 3Phase Clean Water(Soft Water) Operational Temperature Range 10 C Above Water Supply Temperature to 130 C Cooling Capacity Capacity Volume Maximum Circulation Flow Rate Output Cooling Method Water Level Detector Input Control Panel Outer Dimension Product Weight Direct Cooling Indirect Cooling Floatless Swich NOTE2 Standard for Water Supply Pressure Setting Temperature Water Supply Pressure The change of water supply pressure causes damage in pump and float switch, etc. Be sure to keep stable pressure for primary side water supply. When the water supply quantity is lacking, the cooling operation is sometimes decompressed by the lacking for water supply. The supply water flow must be more than above chart. When the water supply pipe is narrow and it's distance is long, the cooling operation is sometimes decompressed by the lacking for water supply. Please use pipe diameter for large size. << Reference >> In less than 2 m: 3/8B (Internal diameter 12) In less than 5 m: 1/2B (Internal diameter 15) Adjust the drain side pressure power to about MPa. When the water supply pressure is low, install available separately pressure pump, etc. When the water supply pressure is high, use the pressure release valve, etc. Be sure to install appropriately scale pressure gauge in primary side water supply pipe and drain pipe. Water supply side: 0-1.0MPa (1.6MPa) Drain side: MPa

Customized Industrial Products

Customized Industrial Products Product Catalog Large Walk-in Type Drying Oven Large Size Autoclave Large Size Fine Oven Targeting Productivity Improvement Yamato offers customization of products based