Operating handbook Feeder Ironer Folder & Stacker IC44819FFS IC44825FFS IC44832FFS USA

Transcription

1 Operating handbook Feeder Ironer Folder & Stacker IC44819FFS IC44825FFS IC44832FFS USA USA/GB.201

2 .

3 INSTRUCTION 0. Table of contents Pages/Chapters General instructions Preliminary instructions... 1/1 General... 1/2 Precautions for use... 1/3 Pages/Chapters Appendices Washing symbols... 1/10 Easy start Machine operation Additional instructions... 1/4 Machine starting... 2/4 The "Move back" key... 2/4 Setting out... 2/4 Diamms mode... 3/4 Manual mode... 4/4 Using the handle...4/4 Folds table choice... 5/4 Stopping... 6/4 Cooling... 7/4 Power is back... 8/4 Emergency stop... 9/4 To run a dry program... 10/4 Energy saving mode... 11/4 Advanced use Basic settings... 1/5 Set folds table... 3/5 Advanced settings... 4/5 To select "statistics"... 6/5 Daily statistics... 6/5 Clock adjustment... 7/5 Password change... 8/5 Language setting... 9/5 Programming... 10/5 Create wash program... 11/5 Program edition... 12/5 Modify a program... 14/5 Delete a program... 18/5 Additional information of using Diagram of Clarus TS menus... 1/6 Safety Safety... 1/7 Operating incidents Order of service... 1/8 Maintenance Preventive maintenance... 1/9 Lubrifi cation table... 7/9 Replacing ironing bands... 8/9 The manufacturer reserves the right to modify construction and equipment characteristics.

4 INSTRUCTION 0. Table of contents This page is left blank on purpose.

5 INSTRUCTION 1. Preliminary instructions Preliminary instructions Before any use, it is compulsory to read the instruction handbook. Users must have learnt how the machine operates. The identification plate is placed on electric cabinet side of the machine. In order to prevent any risk of fire or explosion, flammable products should never be used to clean the machine. Any repair or maintenance intervention should be carried out by qualified personnel only. Installation and putting into service must be carried out by trained staff. N.B. : this machine has no part made of asbestos. Explanation of graphic symbols A flash of lightning with an arrow at its end displayed inside an equilateral triangle, warns the user about the presence of uninsulated "dangerous current" sufficient in intensity to cause electrocution. An exclamation mark inside an equilateral triangle offers the user important advice about usage, servicing and hazardous conditions. This symbol warns the user that there are mechanisms inside the machine which can be dangerous. The protective housing must be in place during use. This symbol warns the user of the presence of high temperatures which could cause severe burns. Some surfaces can reach close to 200 C (392 F).

6 INSTRUCTION 1. Preliminary instructions You should have found an instruction handbook and keys to open the machine casings, and a maintenance poster to display in your laundry, inside your machine. Depending on its destination, the dryer ironer is delivered bare or may be placed on a transport pallet and/or packed with plastic film. In some cases, it may be delivered in maritime packing (wood crate). Please refer to the handling chapter in this instruction handbook for a description of handling operations. This machine should be installed in conformance to the health and safety regulations, and only used in a sufficiently aerated area. Check the instructions before installing or using the machine. The use and handling of chemical products such as detergent, chlorine, acids, antiliming agents etc... may create hazards for health and environment ; the following precautions should be taken. - Do not breathe the dusts or steam. - Avoid contact with skin or eyes (may cause burns). - In case of important spillage, wear a protecting mask, gloves, and eye protectors. - Handle with care. - Consult the use and first aid advice on the packings. - Do not dispose pure products in the environment. The machine can work without the protective casing when the electric supply is not cut off. Interlock the main isolating switch with a padlock. Close the steam inlet valves.

7 INSTRUCTION 1. Preliminary instructions Easy start For a quick drive of the machine, an insert «Easy start» surrounds some pages. This allows you to realize yours first ironing programs in a quick time. Easy start Easy start

8 Preliminary instructions INSTRUCTION Identification plate USA/CANADA Model IC44819FFS Serial No xxxxx/xxxxxxx Gas Type: NAT Propane Manufacturer s address: ELECTROLUX LAUNDRY SYSTEMS France 52 rue Pasteur BP Rosières Près Troyes - France Conforms to: - UL 795: CGA 7.3 : 1971 MFG. Date xx/xx/2010 QC No xxxxxxxx Orifice size: Nat 3.3 mm (x3) Propane 1.85 mm (x3) Heat Input Nat gas: BTU/hour (C.V 34,02 MJ/m³) Gas Supply Pressure: Nat: 8.0 w.c, 2.0 kpa Manifold Pressure: Nat: 4.49 w.c, 1.12 kpa Heat Input Propane gas: BTU/hour (C.V 46,34 MJ/kg) Gas Supply Pressure: Propane: 14.9 w.c, 3.7 kpa Manifold Pressure: Propane: 14 w.c, 3.5 kpa Electrical rating: Volts 208/240 Total input Amp: 15 A Hertz 60 Mini. supply conductor ampacity: 20A Phases 3 Nontime delay fuses: 20 A WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or service this equipment. For safety reasons use only original spare parts. ATTENTION : L installation, le réglage, la maintenance, ou l entretien inapropriés peuvent causer des dégats matériels, des blessures ou la mort. Lisez complètement les notices d installation, d utilisation et d entretien avant d installer, d utiliser ou d entretenir cet équipement. Pour des raisons de sécurité, utiliser uniquement des pièces de rechange d origine. USA/CANADA Model IC44819FFS Serial No xxxxx/xxxxxxx Manufacturer s address: ELECTROLUX LAUNDRY SYSTEMS France 52 rue Pasteur BP Rosières Près Troyes - France Conforms to: - UL 141 : 2007 CAN/CSA C22.2 No. 68 MFG. Date xx/xx/2010 QC No xxxxxxxx Steam operation supply pressure: 900 kpa Maximum supply pressure: 1 MPa Warning: Safety valve exhaust must be connected to the outside of the building. Electrical rating: Volts 208/240 Total input Amp: 15 A Hertz 60 Mini. supply conductor ampacity: 20A Phases 3 Nontime delay fuses : 20 A WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or service this equipment. For safety reasons use only original spare parts. ATTENTION : L installation, le réglage, la maintenance, ou l entretien inapropriés peuvent causer des dégats matériels, des blessures ou la mort. Lisez complètement les notices d installation, d utilisation et d entretien avant d installer, d utiliser ou d entretenir cet équipement. Pour des raisons de sécurité, utiliser uniquement des pièces de rechange d origine.

9 INSTRUCTION 2. General General instructions The machines described in this hanbook have a ironing capacity of 190, 250, 320 cm wide depending on the type. They are available with steam or gas heating. They carry out five different fonctions with a single operator; the space required is very similar to the standard ironer s. The ironing speed is adjustable as a function of the density (weight/m 2 ) and humidity of the washing. The temperature of the ironing cylinder can also be adjusted by a thermostat (except for steam; in this case, the temperature depends on the steam pressure). The ironing parameters that you have selected are permanently checked by a microprocessor. These parameters are displayed in real time on a tactile screen in front of the operator. The feeding of the linen is completely automatized and includes smoothing; a single operator is required; the folding of the items is calculated for each item fed. Several piles of linen can be stored in the stacker with centering and numbering of the folded items. The machine can be used like a standard ironer with or without the automatic feeding. Identification plate ELECTROLUX ITS D1582

10 General INSTRUCTION This dryer ironer is controlled by a microprocessor-based program control unit placed on the loading side. There are many advantages to this equipment, including : Folding adjustment is controlled with great precision and flexibility. The large display screen means that detailed information on iron programs, machine status and operations, dry speeds and temperatures can be accessed in plain language. It is possible for the user to create new iron programs, and to adapt programs with great precision, on the basis of experience and to suit various types of textile, degrees of moisture etc. A very high level of machine safety through continuous monitoring and built-in safety interlocks. Great flexibility during program operation : - easy change from DIAMMS mode till MANUAL mode and inversely; - the user can change temperatures and speeds directly, during program operation; - change to running a different iron program, at any time during program operation of the dryer ironer. Display screen ELECTROLUX ITS CPU Software Version 1.00 Lever for manual mode Emergency stop START WASHPROGRAM OPTIONS MENU Use up and down key then press Function keys. The functions of these keys change, depending on which menu or part of a menu you are using. Emergency stop D1582

11 INSTRUCTION 2. General Emergency stop The emergency stop must be unblocked, if not the machine will not work (to unblock, turn the red button to the right). If the machine for some reason has to be stopped, abnormal or dangerous running, press emergency stop button. Release the emergency stop, by turning it clockwise only after checking what motivated this stop. D0543 D0544

12 INSTRUCTION 2. General Control handle The control handle will operate differently depending on the parameters selected on the display screen settings. In automatic mode, only function (1) is available. Pull the control handle forwards to release the sheet from the clamps and cancel automatic feeding (the sheet will fall into the reception tray). If you modify the parameters of the «Basic settings» menu, the control handle will switch to a semi-automatic or manual mode. Start auto feeding = 0 Push the handle to position (2) to start feeding. Start auto feeding = 1 Feeding will occur automatically after introducing the piece of linen to be dried into the clamps. 1 2 D2225 Auto feeding return = 0 Pull the handle to position (1) to bring the feeding clamps back to their initial position. Auto feeding return = 1 Feeding return is automatic once the piece of linen has been placed on the belts

13 INSTRUCTION 2. General Stacker control panel 1. Emergency stop pushbutton 2. Linen stack removal indicator 3. Linen removal pushbutton or re-initialisation of stacker defect 1 4. Sheet counter with reset function Note: the ironer - dryer will not operate if the stacker is not connected to the power supply. When a stack has been created (approx. height: 210 mm) on the stacker deck, this stack will be removed to the evacuation table. The indicator (2) on the stacker control panel will flash for a few seconds to indicate that a stack has been completed D2223 Note: the evacuation table can contain one completed stack and another stack in progress on the stacker deck. Remove the stacks as they reach the evacuation ramp. A pushbutton (3) can be used to evacuate the stack of linen manually. A sheet counter (4) with reset function can be used to count the items ironed during a given period.

14 INSTRUCTION 2. General Note about the A.C. power According to the EN :1997 standard, the machine is provided for AC supplies corresponding to the extracted caracteristics below : AC supplies Voltage : Steady state voltage : from 0.9 to 1.1 of nominal voltage. Frequency : from 0.99 to 1.01 of nominal frequency continuously. from 0.98 to 1.02 short time. Harmonics : Harmonic distorsion not to exceed 10% of the total r.m.s. voltage between live conductors for the sum of the second through to the fifth harmonic. An additional 2% of the total r.m.s. voltage between live conductors for the sum of the sixth through to the 30th harmonic is permissible. Voltage unbalance : Neither the voltage of the negative sequence component nor the voltage of the zero sequence component in three-phase supplies shall exceed 2% of the positive sequence component. Voltage interruption : Supply interrupted or at zero voltage for not more than 3ms at any random time in the supply cycle. There shall be more than 1 second between successive interruptions. Voltage dips : Voltage dips shall not exceed 20% of the peak voltage of the supply for more than one cycle. There shall be more than 1 second between successive dips.

15 INSTRUCTION 3. Precautions for use Precautions for use The machine should not be used by children. This ironer must be used exclusively for textiles appropriate for machine ironing, which have been previously and exclusively washed in water. This machine is for professional use and must be used exclusively by qualified personnel. Blankets should not be ironed. Be careful with synthetic linen and also with printed linen. They can melt and stick on the cylinder. Do not iron articles that contain plastic, foam, sponge rubber or similarly textured rubberlike materials. Do not iron linens coated with solvent, paint, wax, grease or any easily inflammable products. In case of a gas heated machine, do not assemble the machine on premises containing a dry cleaning machines or other similar machines. CAUTION Do not push small pieces of laundry in front of the DIAMMS turners to avoid jamming

16 Precautions for use INSTRUCTION PRACTICES TO AVOID : - Sheets folded double. - Draw-sheets or any other double-layer sheet or sheet pulled into the machine side by side. - Fitted-sheet : May cause problem to smooth out; Measurements altered. - Comforter cases with flap - Linen 80 gr /m² : gravitational pull difficult at lengthwise folding - Linen 200 gr/m². - Linen < 0,90m x 1,10m. PRACTICES NOT ADVISABLE : - Worn polycotton sheets (cotton worn away) : get out of shape when smoothed out, uneven finish look when folded, high static electricity. - Large cotton or flax-made sheets > 200 gr/m² (layers > 80 mm after the 3rd cross fold). - Linen other than flatwork : (butcher's apron : watch that the cords do not slide between the feeding belts). - Sheets of 1m80 x 2m80 processed on type 25-2m50 - (gas heating : problem of heating regulation with gas; gas burners cannot be modulated ). CAUTIONS : - Prepare the large sheets before feeding : ironing and folding defects, risks of jamming at cross folding. - Avoid the torn, worn or holed sheets : that may hook and alter the measurements hampering proper lengthwise folding (back clearing). - Comply with the mini-maxi sizes. - Avoid when running, too low or bad adjusted temperatures as consequence of : - A too high ironing speed with high moisture content in sheets : bad sliding on metallic parts. - A partial use of the ironing length of the cylinder creating overheating : (be careful especially, to the risk for the polycotton sheets to loose their shape, generally stabilized at 200 C). D0411

17 INSTRUCTION 4. Machine operation Additional instructions to optimise a dryer-ironer When ironing small sheets or small washing, pass abreast the washing of the heating cylinder to provide correct regulation of the cylinder temperature. As a general rule, the whole of the cylinder should be used (1). Either iron the linen from the front (2) or iron alternately (3), which makes maximum use of the heat units available over the surface of the cylinder. It also overcomes difficulties arising from random control values caused by partial use of the cylinder. Easy start Cylinder Easy start Linen D1097

18 Machine operation INSTRUCTION Machine starting The "Move back" key If you find you are in the wrong place, or if you want to undo earlier key presses : Press the "Move back" key one or more times. The "Move back" function Each press of the "Move back" key moves you back one menu, in reverse order. By pressing this key repeatedly you can return to this menu at any time : Easy start 180 C 5,5 m 2 min Setting out STOP D1663 ELECTROLUX ITS CPU Software Version 1.00 START PROGRAM OPTIONS MENU After putting the main switch on 1, the menu opposite is displayed on the machine. Use up and down key then press START PROGRAM OPTIONS MENU If "OPTIONS MENU" is highlighted, Press this key. START PROGRAM OPTIONS MENU When "START PROGRAM" is highlighted, Easy start Press this key. u"diamms MODE" display (following page)

19 INSTRUCTION 4. Machine operation "DIAMMS MODE" display 180 C 5,5 m 2 min During the operating cycle, the display shows the opposite informations and commands in DIAMMS mode. Warming up From the machine starting, the order of warming up is given. The cylinder temprature increases. The machine is adjusted in automatic mode by default. Easy start 1 STOP Temperature D1663 To go in MANUAL mode, push on : Shows the cylinder temprature. "Diamms/Manual" u"manual MODE" display (following page) Speed To go in feeding mode, push on : "Feeding" Shows the cylinder speed. Moisture 1 To go in without folding mode, push on : Shows the moisture. Counter of items "Folding" To go in ejection mode, push on : Shows the number of items of linen passed in the machine. "Ejection" Folds table choice To go in select program mode, push on : 1 Shows the selected folds table. "Select program" Easy start To stop the operating cycle, push on : "Stop"

20 INSTRUCTION 4. Machine operation Remark: Incompatibility of the DIAMMS with the ironing of the linen with double thickness The use of automatic control mode using the DIAMMS is not recommended for ironing clothes with a double thickness (eg duvet covers), the measurement of residual moisture being carried on thickness. It is advisable in this case return to MANUAL mode and adjust the speed of ironing to get a good drying performance. Easy start Easy start Using the handle The dryer ironer is fitted with a handle. This is very useful to take out the washing if there is a power failure while you are ironing; or you can use it to feed a piece of wet washing to protect the ironing bands when the ironing temperature is too high. Lift the safety plate (1) then push (2) and turn the handle in the clockwise direction (3) to rotate the cylinder and take out the washing. Handle D1092

21 INSTRUCTION 4. Machine operation "MANUAL MODE" display C 5,5 m 2 min During the operating cycle, the display shows the opposite informations and commands in MANUAL mode. MANUAL mode selection If you push on you go in manual mode. Easy start STOP D1662 In this mode, you select in the following menus, the temperature and the ironing speed you want apply to use the machine. To go in DIAMMS mode, push on : "Diamms/Manual" Set temprature u"diamms MODE" display (previous page) Now the display waits for you to select the set temperature for the ironing. 1 To go in feeding mode, push on : "Feeding" To go in without folding mode, push on : The ironing temperature can be adjusted degrees by degrees Celsius by push. N. B. : if you want a temperature below 100 C, the display shows a sign (0) to indicate that the heating is cut off and allows the machine to work without heating. "Folding" Ironing speed To go in ejection mode, push on : "Ejection" Now the display waits for you to select the ironing speed. To go in select program mode, push on : The ironing speed is adjusted between a minimal value and a maximal value in the Setting mode. The adjustment can be modified 1/10 by 1/10 of meter by push. Easy start "Select program" To stop the operating cycle, push on : "Stop" Note that the minimal and maximal ironing speeds are in accordance with the adjustment parameters of the converter. u"stopping" menu(following page)

22 INSTRUCTION 4. Machine operation "FOLDS TABLE CHOICE" display FOLDS TABLE CHOICE 0. Factory folds table 1. Customized folds table (recommended) 1. Reversed customized folds table 2. Specific folds table 2. Reversed specific folds table In Diamms or Manual mode, when we touch the screen in the center area, the «FOLDS TABLE CHOICE» screen appears as opposite. Folds table choice This screen allows you to select the folds table: n 0 Factory folds table, n 1 Customized folds table, n 1 Reversed cutomized folds table, Easy start n 2 Specific folds table, n 2 Reversed specific folds table. To choose the folds table. Press on and keys to select the folds table you want to use, then press the Valid key to validate your choice or press the Move back key to cancel. To escape, push on : "Move back" key u"diamms / MANUAL MODE" display (previous page) To valid, push on : "Valid" key u"diamms / MANUAL MODE" display (previous page) Easy start

23 INSTRUCTION 4. Machine operation "STOPPING" menu STOPPING? To confirm, push on To access tools, push on Stopping This function allows you to stop the machine or to access the «Options menu» to carry out a modification. Before stopping, the machine executes a cool down stage that allows to avoid damage to the ironing bands. Easy start To escape, push on : "Move back" key u"diamms / MANUAL MODE" display (previous page) To enter, push on : "Valid" key u"electrolux ITS" or "COOLING" menu (following page) Otherwise, push on : "Tools" u"options MENU" Easy start

24 INSTRUCTION 4. Machine operation "COOLING" menu Stop confirmed, cooling Cooling This display allows you to follow the cool down stage. You can at every time stop this cool down stage to start again, or access the «Options menu» to carry out a modification. Easy start To escape, push on : "Move back" key u"power IS BACK" display (following page) Otherwise, push on : "Tools" u"options MENU" "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE To escape, push on : "Move back" key u"cooling" menu Easy start

25 INSTRUCTION 4. Machine operation "POWER IS BACK" display POWER IS BACK Do you want to continue the cycle? Power is back In case of escaping of the cooling stage, the screen opposite is displayed to take back the use of the machine. Easy start To escape the program, press "Move back" key u"cooling" menu (previous page) To continue the cycle, press the "Valid" key u"diamms / MANUAL MODE" display Easy start

26 INSTRUCTION 4. Machine operation "EMERGENCY STOP" display 01. EMERG. STOP ACTIVE Desactive emergency stop and restart the machine After a pushing on the emergency stop, the opposite display appears. Emergency stop Easy start If the machine for some reason has to be stopped, abnormal or dangerous running, press emergency stop button. After the emergency stop releasing, push on : Release the emergency stop, by turning it clockwise only after checking what motivated this stop. "Valid" key u"electrolux ITS" menu Easy start

27 INSTRUCTION 4. Machine operation Run a program The "Select program" key 180 C Easy start 5,5 m 2 min STOP D1663 To go in select program mode, push on : "Select program" "SELECT PROGRAM" menu SELECT PROGRAM 00 Universal 01 Folding adjustment mode 02 Cloth 300x240 poly/cotton 05 Draw-sheet 190x Fitted-sheet 300x240 cotton 18 Cloth 190x240 poly/cotton 20 Draw-sheet 250x240 Customer programs Program After pushing on select program, the opposite display appears. The number and the name of program are indicated above the command buttons. Allows to choose the program. Previous and following page. Easy start To enter, push on : "Valid" key u"diamms / MANUAL MODE" menu (following page)

28 INSTRUCTION 4. Machine operation Start the selected dryprogram (in this case 18) Program mode The functions are the same as for the operating cycle in Universal Diamms mode. Easy start 18 Cloth 190x240 poly/cotton Elis "ENERGY SAVING MODE" display MACHINE IN ENERGY SAVING MODE Energy saving The «Energy saving» mode shuts off the machine after a predefined time in the settings. Push on the screen to restart the machine. uprevious page (according to operation) To restart at previous mode : NOTE: in «Energy saving» mode, the machine adjusts temperature to the setpoint temperature minus 40 C. Easy start

29 INSTRUCTION 5. Advanced use BASIC SETTINGS Since the "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE Select the "BASIC SETTINGS" menu by pressing this keys. Then valid. "NUMERIC KEYBOARD" menu Password : # Numeric keyboard A password (a four-digit number), protects the access to the "Basic settings" functions. D1312 Compose the four number code with the numeric keys. You can correct a bad capture by pressing this key. Then valid. u"basic SETTINGS" menu (following page)

30 Advanced use INSTRUCTION "BASIC SETTINGS" menu BASIC SETTINGS Feeding auto. start : 0 Feeding auto. return : 0 Folds table choice : 0 Folding table setting Feeding sucking system : 0 Standby timer (min) : 0 Sleeping timer (min) : 0 Lenght counter display : Select the wished function by pressing this keys. Decrease or increase the value by pressing this keys. Basic settings Feeding auto. start 1= the feeding start is automatic after introduction of the linen item in the two pincers; 0= the central lever must be actionned. Feeding auto. return 1= the feeding return is automatic after putting the linen item on the bands; 0= the central lever must be actionned. Folds table choice 1 = the machine will use the «standard» folding table; 0 = the machine will use the «factory» folding table. Folding table setting Allows to access to the «customer folding table» display. u"folding TABLE" display (following page) 0 1 Then valid. Feeding sucking system 1=, the feeding suction is on; 0= is off for the little items of linen.this allows to decrease the sound level of the machine and so the electrical consumption. Standby timer (min) Adjusts the time before standby (minutes). Sleeping timer (min) Adjusts the time before automatic stop (minutes). Length measure display 1= shows the item length instead of the counter of items (cm). 3rd Cross Fold activat. 0 = cross fold 3 disabled. 1 = cross fold 3 enabled. Parameters saving Saves board parameters in the event that one of them is replaced.

31 INSTRUCTION 5. Advanced use "SET CUSTOMIZED FOLDS TABLE" menu SET CUSTOMIZED FOLDS TABLE 0. Factory folds table Length = Length < 185 Fold 1 (0): 0 Fold 2&3 (0): 0 Fold 4&5 (0): 0 Fold 6&7 (0): 0 = > Last fold = 0 & offset = Select the wished function by pressing this keys. Decrease or increase the value by pressing this keys. Then valid. Set customized folds table 0. Factory folds table 1 = use customer folding table; 0 = no adjustment possible. Lenght = 182 Length of the last item inserted into the machine (= 0, when the machine is stopped). 180 Lenght < 185 Selected length range. Automatically selected when the machine is in use. Fold 1, Folds 2&3... Value of each fold for the selected length of fold (factry settings in brackets). CAUTION: To guarantee a correct result, ensure that the last fold 23 and the penultimate fold has the largest value. NOTE: This screen can also be accessed from the program list (program No. 1) when the machine is in use.

32 Advanced use INSTRUCTION ADVANCED SETTINGS Since the "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE Select the "ADVANCED SETTINGS" menu by pressing this keys. Then valid. "NUMERIC KEYBOARD" menu Password : # Numeric keyboard A password (a four-digit number), protects the access to the "Advanced settings" functions. D1312 Compose the four number code with the numeric keys. You can correct a bad capture by pressing this key. Then valid. u"advanced SETTINGS" menu (following page)

33 INSTRUCTION 5. Advanced use "ADVANCED SETTINGS" menu ADVANCED SETTINGS Machine configuration Machine timers setting Parameters recovering Maintenance alert (h) : 134 Advanced settings Machine configuration Access reserved to the technician. Machine timers setting Access reserved to the technician. Perameters recovering Access reserved to the technician. Select the wished function Maintenance alert (h) Access reserved to the technician. by pressing this keys. Then valid.

34 Advanced use INSTRUCTION STATISTICS Since the "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE Select the "STATISTICS" menu by pressing this keys. Then valid. "NUMERIC KEYBOARD" menu Password : # Numeric keyboard A password (a four-digit number), protects the access to the "Statistics" functions. D1312 Compose the four number code with the numeric keys. You can correct a bad capture by pressing this key. Then valid. u"statistics" menu (following page)

35 INSTRUCTION 5. Advanced use "STATISTICS" display STATISTICS Day statistics Monthly statistics Absolute statistics Temperatures statistics Errors statistics To move back, press the : "Move back" key u"options MENU" Select "Day statistics" by pressing this keys. The «Statistics» function The Statistics function gives you access to the following information : Day statistics List the statistics recorded in a day. Monthly statistics Access with Customer passord. Absolute statistics Access reserved to the technician. Temperature display Access reserved to the technician. Errors statistics Access reserved to the technician. Then valid. "Day statistics" menu Day statistics Total Hours Since New (min) : 480 Used Hours (min) : 420 Processed items : 1028 Machine defaults : 1 Rejected items : 187 To escape, push on : "Move back" key u"statistics" menu Otherwise, push on "Valid" key Day statistics Total Hours Since New (min) Shows the total operating time for the machine since new. Used Hours (min) Shows the total using time. Processed items Counts the items treated in a day. Machine defaults Counts the machine defaults recorded in a day. Rejected items Counts the items rejected in a day. u"statistics" menu Reset the counters.

36 INSTRUCTION 5. Advanced use DATE AND TIME SETTING Since the "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE Select the "DATE & TIME SETTING" menu by pressing this keys. Then valid. "DATE & TIME SETTING" menu DATE & TIME SETTING DATE: 00/00/00 dd/mm/yy Date format (+/-) TIME 00:00 Date & time setting This function allows you to adjust the date and the hour of the machine. This is notably useful to quote the statistics and the maintenance. To escape, push on : "Move back" key To move the cursors, To set the value indicated by the cursor, To enter, push on : "Valid" key

37 INSTRUCTION 5. Advanced use LANGUAGE SETTING Since the "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE Select the "USER LANGUAGE" menu by pressing this keys. Then valid. "USER LANGUAGE" menu USER LANGUAGE English Français Deutsh Español Italiano Nederlands English Français Deutsh Español If another language is highlighted, press this keys. English Français Deutsh Español When the wished language is highlighted, press this key.

38 Advanced use INSTRUCTION PROGRAMMING Since the "OPTIONS MENU" OPTIONS MENU BASIC SETTINGS PROGRAMMING ADVANCED SETTINGS STATISTICS DATE & TIME SETTING PASSWORD CHANGE MACHINE STATUS USER LANGUAGE Select the "PROGRAMMING" menu by pressing this keys. Then valid. "NUMERIC KEYBOARD" menu Password : # Numeric keyboard A password (a four-digit number), protects the access to the "Programming" functions. D1312 Compose the four number code with the numeric keys. You can correct a bad capture by pressing this key. Then valid. u"programming" menu (following page)

39 INSTRUCTION 5. Advanced use CREATE PROGRAM Since the "PROGRAMMING" menu PROGRAMMING CREATE PROGRAM MODIFY PROGRAM DELETE PROGRAM An introduction to programming You can create a completely new program from a basic program and by programming a number of adjustments to form a new program. Programs can be created directly on the machine s control console. Select the "CREATE PROGRAM" menu by pressing this keys. Then valid. u"program EDITION" menu (following page)

40 Advanced use INSTRUCTION "PROGRAM EDITION" menu PROGRAM EDITION ## DIAMMS regulation : 0 Temperature : 178 C Speed (m/mn) : 4,5 Automatic feeding :1 Automatic return : 0 Non-folded length (cm) : 190 Non-folded width (cm) : 240 Folding : 1 Length L (cm) : 38 Width W (cm) : 32 Cloths nb by stack : To escape, push on : "Move back" key Select the wished parameter by pressing this keys. Decrease or increase the value by pressing this keys. Then valid. Program edition The parameters of each program are accessible and can be modified : DIAMMS regulation Allows to select between DIAMMS or MANUAL mode. Temperature Adjusts the temperature. Speed (m/mn) Adjusts the speed. Automatic feeding Enables automatic feeding, otherwise feeding is done manually. Automatic return Authorizes the automatic return, dans in the contrary case, the return is driven by the central lever. Non-folded length (cm) Indicates the non-folded length (± 6cm). Non-folded width (cm) Indicates the non-folded width (± 6cm). Folding Allows the folding. Length L (cm) Adjusts the stack length. Width W (cm) Adjusts the stack width. Cloths number by stack Adjusts the cloths number by stack. u"program NUMBER" menu (following page)

41 INSTRUCTION 5. Advanced use "PROGRAM NUMBER" menu Enter the program number : Program number A number allows to select the dry programs by numerical order. Compose a number with the numeric keys. D1312 You can correct a bad capture by pressing this key. Then valid. u"numeric KEYBOARD" menu "NUMERIC KEYBOARD" menu Program Name : Program Name : FF_ Program Name : F_ Compose your program name with the numeric keys, by pressing 1, 2 or 3 times on each key. You can correct a bad capture by pressing this key. Then valid. Numeric keyboard A numeric keyboard allows to give a program name (formed by letters). Each of the numeric keys gives access to several characters as follows : 1 : abc 2 : def 3 : ghi 4 : jkl 5 : mno 6 : pqr 7 : stu 8 : vwx 9 : yz 0 : The first time you press a given key, the first character available through that key will appear on the display. One press on 1 produces A. One press on 2 produces D. Simply press the relevant key the required number of times until the character you want appears on the display. For example, to insert the letter C, press key 1 three times. To insert F, press 2 three times. When the character you want is on the display, wait a minute the cursor sets after. u"programming" menu

42 INSTRUCTION 5. Advanced use MODIFY PROGRAM Since the "PROGRAMMING" menu PROGRAMMING CREATE PROGRAM MODIFY PROGRAM DELETE PROGRAM An introduction to programming You can create a new program starting from a basic program and by programming a number of adjustments, to form a new program. Select the "MODIFY PROGRAM" menu Programs can be programmed directly on the machine, via the PCU control panel, which is the method described in this manual. by pressing this keys. Then valid. "SELECT PROGRAM" menu SELECT PROGRAM 01 Universal 02 Cloth 300x240 poly/cotton 05 Draw-sheet 190x Fitted-sheet 300x240 cotton 18 Cloth 190x240 poly/cotton 20 Draw-sheet 250x Folding adjustment mode Allows to choose the program. Previous and following page. To enter, push on : "Valid" key u"program EDITION" menu (following page)

43 INSTRUCTION 5. Advanced use "PROGRAM EDITION" menu PROGRAM EDITION ## DIAMMS regulation : 0 Temperature : 178 C Speed (m/mn) : 4,5 Automatic feeding :1 Automatic return : 0 Non-folded length (cm) : 190 Non-folded width (cm) : 240 Folding : 1 Length L (cm) : 38 Width W (cm) : 32 Cloths nb by stack : 05 Program edition See page 12 / Chapter 5 Then valid. u"program NUMBER" menu "PROGRAM NUMBER" menu Enter the program number : Program number See page 13 / Chapter 5 D1312 Then valid. u"numeric KEYBOARD" menu (following page)

44 INSTRUCTION 5. Advanced use "NUMERIC KEYBOARD" menu Program Name : Numeric keyboard See page 13 / Chapter 5 Then valid. u"kill THE EXISTING PROGRAM" display "KILL THE EXISTING PROGRAM" display DO YOU WANT TO OVERWRITE Kill an existing program When the validation executed, the previous program is definitely lost and replaced by the new one. EXISTING WASHPROGRAM? To escape, push on : "Move back" key u"numeric KEYBOARD" menu Otherwise, push on : "Valid" key u"programming" menu

45 INSTRUCTION 5. Advanced use This page is left blank on purpose.

46 INSTRUCTION 5. Advanced use DELETE PROGRAM Since the "PROGRAMMING" menu PROGRAMMING CREATE PROGRAM MODIFY PROGRAM DELETE PROGRAM Select the "DELETE PROGRAM" menu by pressing this keys. Then valid. "SELECT PROGRAM" menu SELECT PROGRAM 00 Universal 01 Folding adjustment mode 02 Cloth 300x240 poly/cotton 05 Draw-sheet 190x Fitted-sheet 300x240 cotton 18 Cloth 190x240 poly/cotton 20 Draw-sheet 250x240 Allows to choose the program. Previous and following page. To enter, push on : "Valid" key u"delete THE PROGRAM" display (following page)

47 INSTRUCTION 5. Advanced use "DELETE THE PROGRAM" display Delete a washprogram When the validation is executed, the program is definitely deleted. DO YOU WANT TO DELETE THE PROGRAM? To escape, push on : "Move back" key u"programming" menu Otherwise, push on : "Valid" key u"programming" menu

48 INSTRUCTION 5. Advanced use "SELECT PROGRAM" menu ELECTROLUX ITS CPU Software Version 1.00 START PROGRAM OPTIONS MENU Use up and down key then press From the start menu, Select «START MACHINE», Select «START PROGRAM» START PROGRAM OPTIONS MENU Then valid. u"diamms MODE" screen 180 C The «DIAMMS MODE» screen appears as shown opposite. 5,5 m 2 min STOP D1663 Push on «Select program» u"select PROGRAM" screen

49 INSTRUCTION 5. Advanced use SELECT PROGRAM 00 Universal 01 Folding adjustment mode 02 Cloth 300x240 poly/cotton 05 Draw-sheet 190x Fitted-sheet 300x240 cotton 18 Cloth 190x240 poly/cotton 20 Draw-sheet 250x240 The «SELECT PROGRAM» screen appears as shown opposite. Select program No. 01 «Folding table adjustment mode» Then valid. u"set CUSTOMIZED FOLDS TABLE" display SET CUSTOMIZED FOLDS TABLE 0. Factory folds table Length = Length < 185 Fold 1 (0): 0 Fold 2&3 (0): 0 Fold 4&5 (0): 0 Fold 6&7 (0): 0 = > Last fold = 0 & offset = 0 The «SET CUSTOMIZED FOLDS TABLE» screen appears as shown opposite. Select a function by pressing these keys. 0 0 Raise or lower the value by pressing these keys. CAUTION: To guarantee a correct result, ensure that the first fold 23, the last fold 23 and the penultimate fold has the largest value. 0 1 Then valid.

50 Additional 6 INSTRUCTION information of using Diagram of Electrolux ITS menus POWER IS BACK EMERGENCY STOP ECRAN ELECTROLUX ITS OPTIONS MENU PROGRAMMING STOPPING BASIC SETTINGS DIAMMS MODE MANUAL MODE ADVANCED SETTINGS SELECT PROGRAM STATISTICS DATE & TIME SETTING DIAMMS X PROGRAM MANUAL X PROGRAM PASSWORD CHANGE Caption : normal functioning adjustment function wrong functioning Caption : normal way move back way password Caption : normal way with automatical advance emergency stop or «power is back» way MACHINE STATUS USER LANGUAGE

51 INSTRUCTION 6. Additional information of using CREATE PRO....EDITION CREATE PRO. NUMBER? CREATE PRO. NAME? MODIFY PRO. KILL? MODIFY PRO. SELECT? MODIFY PRO....EDITION MODIFY PRO. NUMBER? MODIFY PRO. NAME? DELETE PRO. SELECT? DELETE PRO. ERASE? FOLDING TABLE DAILY STATISTICS MONTHLY STATISTICS MACHINE CONFIGURATION MACHINE DELAYS SETTING RECUPEARTION PARAMETERS PARAMETRES RECOVERING ABSOLUTE STATISTICS MAINTENANCE ALERT TEMPERATURE DISPLAY ERRORS STATISTICS

52 INSTRUCTION 7. Safety This page is left blank on purpose.

53 INSTRUCTION 7. Safety Safety devices Accessibility All of the casings can be dismantled by means of a specially designed tool. Emergency stop An "emergency stop" button is provided on the left side and on the stacker. Restarting the machine After any stoppage of the machine, either due to power failure, emergency stop, action on the feed safety device, the machine can only be restarted after having pressed "Valid" key. Feed safety device The space between the feed safety flap and the drive bands is too small for you to enter your fingers. The machine stops automatically as soon as the flap is pushed in. Power supply failure If there is a mains power supply failure, use the handle to remove any washing engaged in the machine. If the temperature is too high, use the handle to feed some wet washing and protect the ironing bands. Protection of motors The motors have overload protection : by thermomagnetic circuit breakers and by the electrical selector (for movement). Heating safety device The control panel applies an initial safety level at the time the machine starts up. If the temperature is not reached after a given time, the heating command is desactivated. The operation of the heating function is linked to the rotation of the cylinder. If the cylinder should stop rotating for any reason, the machine stops heating. A safety thermostat, which is independent of all electronic systems, limits the heating temperature of the ironing cylinder in all circumstances, exept in the case of a steam heating machine. There is a thermical fuse for the overheating safety, in the centre of the machines equiped with a Dubixium cylinder. If it breaks, the heating stops. Contact your dealer to check the origin of the failure by a qualified technician. Gas heating The gas burner is ignited and the flame is controlled by an electronic box that provides integral safety, for example if the flue draft is poor or if the gas supply is cut off. A message on the tactile screen shows that the system has been put in a safe condition. A pressure switch connected to the combustion products outlet turns off the machine s heating function in case of extraction problems.

54 INSTRUCTION 8. Operating incidents Operating incidents In order to limit the risk of failure in the electronic controls of the programming unit of the machine, the machine should be earthed. Should interferences happen, the first thing to be checked is the earthing of the machine. The programming unit permanently checks the machine, regarding both safety and working aspects. To make the fault finding easier, the display window indicates in clear text the origin of the failure, or the reason why the particular function cannot be used. The table below gives for each problem detected the message of the machine and the solutions to be brought. Error/Function Cause Action Displayed advertisement : 01. EMERGENCY STOP ACTIVE Release emergency stop and start the machine Reason : one emergency stop button has been pressed. - Abnormal or dangerous running of the machine. If the problem is solved : Push on «Valid» key to restart the machine. - Remedy the problem that caused the emergency stop and release the emergency stop button in a clockwise direction. Displayed advertisement : 02. LACK OF COMPRESSED AIR Check compressed air pressure (5 bars) or contact your technician Reason : A slight drop in air pressure has been detected (detected by the manometer). - Manual water valves (taps) are close. - No air in main supply. - Air leak in the circuit. If the problem is solved : Push on «Valid» key to restart the machine. - Open taps. - Check air in main supply (5 bars on the B1 pressure controller). - Find the leak and repair it. Displayed advertisement : 03. GAS PRESSURE FAILURE Check gas supply valve or contact your technician Reason : A slight drop in gas pressure has been detected. - Manual gas valves (taps) are close. - No gas in main supply. If the problem is solved : Push on «Valid» key to restart the machine. - Open taps. - Check gas in main supply.

55 INSTRUCTION 8. Operating incidents Error/Function Cause Action Displayed advertisement : 04. GAS IGNITION ERROR Reset ignition process or contact your technician Reason : The gas burner does not start. - No gas in connection. - No gas in burner. - No flame in burner. If the problem is solved : Push on «Valid» key to restart the machine. - Check gas in main supply. - Check the Y1/Y2 gas electrovalves. - Check the E2/E3 ignition electrodes. Displayed advertisement : 05. OVERHEAT DETECTION Cool machine down in manual mode or contact your technician Reason : A temperature overheat has been detected. - One of the temperature measurement is over the limit value (<230 C). If the problem is solved : Push on «Valid» key to restart the machine. - Decrease the heating temperature by ironing wet sheets. - Reduce the program s temperature value. Displayed advertisement : 06. MAIN TRANSMISSION ERROR Read instructions in the manual or contact your technician Reason : A problem has occured with the main transmission. - No status change of the counting detector. - No status change of the main transmission when running is asked. If the problem is solved : Push on «Valid» key to restart the machine. - Check the DP1 counting detector. - Check the cinematic chain of the ironing cylinder (motor operation M1, converter A0, transmission chain). Displayed advertisement : 07. LENGTH FOLDING ERROR Read instructions in the manual or contact your technician Reason : A problem has occured with the folding arm. - No status change of the folding arm position detector. - No status change of the folding arm position, despite folding request. If the problem is solved : Push on «Valid» key to restart the machine. - Check the DP3 and DP4 detectors. - Check the cinematic chain of the E1 folding arm (electric clutch operation, transmission chain).

56 Operating 8 INSTRUCTION incidents Error/Function Cause Action Displayed advertisement : 08. FOLDING MEASURE ERROR Read instructions in the manual or contact your technician Reason : A problem has occured with the folding measure. - Sheet not detected at longitudinal fold. If the problem is solved : Push on «Valid» key to restart the machine. - Check the DP7. Displayed advertisement : Actually out of service. 09. FOLDING TRANSFER ERROR Read instructions in the manual or contact your technician Displayed advertisement : 10. CROSS FOLD 1 JAMED Remove item according to instructions in manual or contact your technician Reason : A jamed has occured with cross fold 1. - The sheet is jammed at the inlet of the cross of the first fold. If the problem is solved : Push on «Valid» key to restart the machine. - Clear the item by disengaging the cross transmission if necessary (index pin on the pulley). Displayed advertisement : 11. CROSS FOLD 2 OR 3 JAMED Remove item according to instructions in manual or contact your technician Reason : A jamed has occured with cross fold 2 or 3. - The sheet is jamed in the second or third cross fold. If the problem is solved : Push on «Valid» key to restart the machine. - Disengage the item (see above).

57 INSTRUCTION 8. Operating incidents Error/Function Cause Action Displayed advertisement : 12. JAM AT CROSS FOLD EXIT Remove item according to instructions in manual or contact your technician Reason : A jamed has occured with cross fold exit. - The sheet is jammed at the exit from the cross on the transfer table. - No sheet detection on the transfer table. If the problem is solved : Push on «Valid» key to restart the machine. - Clear the item by disengaging the cross transmission if necessary (index pin on the pulley). - Check the DP28 detector. Displayed advertisement : 13. STACKER ERROR Read instructions in the manual or contact your technician Reason : A bad operation of the stacker is detected. - No status change of the stacker position detection. - No status change of the stacker position. If the problem is solved : Push on «Valid» key to restart the machine. - Check the detector. - Check the mechanical operation of each table function (motion, detection, opening, closing). Displayed advertisement : 14. THERMIC FUSE FAULT Read instructions in the manual or contact your technician Reason : A temperature overheating is detected. - A temperature overheating is detected (>240 C). If the problem is solved : Push on «Valid» key to restart the machine. - Decrease the heating temperature by ironing wet sheets. - When the machine is stopped, change the F2 fuse. Displayed advertisement : 15. OVERHEAT. SAFETY SWITCH Read instructions in the manual or contact your technicien Reason : The overheating safety switch is open. - A temperature overheating is occured (>215 C). If the problem is solved : Push on «Valid» key to restart the machine. - Decrease the heating temperature by ironing wet sheets.

58 INSTRUCTION 8. Operating incidents Error/Function Cause Action Displayed advertisement : 16. EXHAUSTING FAILURE Read instructions in the manual or contact your technician Reason : A problem has occured with the throwing out of the burned gas. - Overabundance of burned gas in the machine. If the problem is solved : Push on «Valid» key to restart the machine. - Check the evacuation of the burning gas as well as the fan motor. Displayed advertisement : 17. HEATING ERROR Read instructions in the manual or contact your technician Reason : A problem has occured with the heating. - Status of the heating contactor is not in accordance with the command. If the problem is solved : Push on «Valid» key to restart the machine. - Stop the machine by means of the main switch, turn the ironing cylinder with the handle to avoid burning the bands. When the cylinder is cold, replace the contactor. Displayed advertisement : 20. COM FAILURE Read instructions in the manual or contact your technician Reason : A problem has occured with the electronic command. - Communication between electronic boards is not working properly. If the problem is solved : Push on «Valid» key to restart the machine. - Check the communication wires between boards.

59 INSTRUCTION 8. Operating incidents This page is left blank on purpose.

60 Preventive maintenance INSTRUCTION Maintenance CAUTION For an optimal service of your machine, execute this instructions at regular intervals and according to the frequency of use.

61 INSTRUCTION 9. Preventive maintenance Daily (8 h) (at the beginning of each working day) 1 Check that the emergency stop button works correctly. 2 Check that the machine stops when you press the mobile safety protector. Weekly (40 h) 3 Clean the drive system of the dewrinkling strips.. 4 Clean motor ventilation grills. 5 Clean the separators. 6 Clean the detection cells and the refl ectors. 7 Check and clean the fl uff fi lter (on gas heating only). Clean the box of the fi lter with suction device. Monthly (170 h) 8 Remove dust from outside the machine. 9 Ensure that the thermostatic regulation and overheat safety shoes are always clean and in contact with the cylinder. 10 Check the condition of the smoothing belts, and replace them if necessary. 11 Lubricate the bearings with high-temperature grease (see lubrication chart in next pages). 12 Turn the blue O ring seals of the feeding pincers through 1/8 of a turn to relieve their bearing surface when the pincers close. Every six months (1000 h) 13 Check for any possible oil seepage, particularly at the fi ller plug (only on Dubixium cylinders). 14 Grease chains (see lubrifi cation table on the following pages). 15 Clean and inspect the cylinder support rollers, along with the stop roller wear indicator (except on the steam machine). If there is any premature wear, see technical support, ref Check operation of the handle. 17 Inspect tightness of electrical connections on the power supply terminal block and electrical earthing connections. 18 Clean exhaust system. 19 Inspect heating elements, cables and electrical connections (on electrical heating only). 20 Clean gas fi lter inside the gas valve (on gas heating only). 21 Check the condition of ironing bands and their staples. 22 Check the feed bands and their drive and ejection bands (on models with the folding funciton only). 23 Remove dust from inside the machine.

62 Preventive maintenance INSTRUCTION Maintenance CAUTION To ensure that your machine gives the very best service, please take care that maintenance is carried strict accordance with the instructions above mentioned.

63 INSTRUCTION 9. Preventive maintenance Every year (2000 h) 24 Check if the cylinder is dirty and clean it if necessary. 25 Inspect and clean external pipes. 26 Check that the burner works correctly (gas machines only). 27 Clean the inner gas burner with suction device. 28 Check the sight of the ceramic plates joints and change them if necessary. 28 The bearings must be grease once a year, you may grease them using a grease which same characteristics as that originally used (grease CELTIA G2). Every three year (6000 h) 30 Clean the ceramic plates with suction device. 31 Change the high temperature joints made of mineral wool. 32 Check the tightness of the venturis. Motors The fan motor is life lubricated. The movement reduction gear is life lubricated. Bearings The bearings must be grease once a year, you may grease them using a grease which same characteristics as that originally used (grease CELTIA G2). Grease periodically the two bearings on the steam cylinder (please see «Preventive maintenance») using a grease which is resistant to high temperatures. Cylinder The cylinder must be maintained very carefully so that ironing is easy and good quality. Detergent or scale deposits must be removed as soon as they reduce ironing quality (jamming, creases on the washing, etc.). Note: The drier-ironing machine textile components must be considered as wearing parts. The lifetime of these parts (ironing strips, feeding strips, clamping belts, transfer belts, etc.) is highly dependent on the usage conditions and maintenance frequencies. Consequently, their replacement may not be claimed under any guarantee.

64 Preventive maintenance INSTRUCTION Air compressor Some machines are supplied with an integrated air compressor. At first start, it is necessary to turn off the compressor manometer tap, wait until the compressor reaches the pressure of 7 bars, then re-open the valve. Every 6 months Check the oil level regularly and top up if necessary (O). Carry out this operation with the machine cold. Start up the ironing machine in folding mode (the reception tub must be in vertical position). Remove the left hand side casing to access the electricity cabinet. O D1816 Activate relay KM9 to move the folding arm forward. KM9 Check that the oil level is now visible on the level indicator. Top up if necessary. Put the arm back in rear position by activating relay KM9 again. Put the side casing back. KM9 D2011 D2011 Every 6 months Check the cleanliness of the intake filter, clean if necessary (F). F D2004