Siteline Primed Swinging Patio Doors Premium Wood

Transcription

1 TABLE OF CONTENT pecifications QuickpecGuide inglewing&frenchdoorhandingandtationarycallouts Elevations/izes:1/4 cale inglewingin-wingandout-wing PanelinglewingIn-wingandOut-wing inglewingcommercialwidthin-wingandout-wing inglewingcommercialwidthwithhandicapill FrenchIn-wingandOut-wing inglewingin-wingandout-wingectortop inglewingcommercialwidthectortop FrenchIn-wingandOut-wingectorTop FrenchCommercialWidthectorTop &10-0TallwingDoors wingdoortransomalignmentguide wingdoortransoms PanelGlazingOptions:3 cale TrimOptions LiteCutInformation Unit izing, Rough Opening, and Masonry Openings ectiondetails:6 cale ectiondetails:3 cale August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-1

2 EXTERIOR FINIH All exterior surfaces are covered with a factory-applied latex primer. AURALAT R WOOD AuraLast R wood is fundamentally different from wood resulting from traditional millwork preservation processes in that it uses a proprietary vacuum/pressure process to provide protection throughout the wood parts used to make windows and doors. AuraLast R wood is distinguished from wood using the current preservation methods by its unique ability to achieve greater penetration of the active ingredients into the wood parts, with a penetration of the treatment being a minimum of 92%. INTERIOR FINIH All interior surfaces are unfinished clear pine ready for on site finishing. Primed and pre-finished interiors are available in paint: Pure White, Extra White, Natural Choice, Moderate White; in stain: Wheat, Cherry, Fruitwood, Cordovan, Cider and Clear Lacquer. Frame is assembled from select kiln dried pine using AuraLast R wood on allexterior parts. Corner joints aresealed with silicone and secured with metal fasteners. Frames are finger jointed with an option for clear on most sizes. Frame thickness is 1-7/32 (31 mm) at head and side jamb and 11/16 (17.5mm) at sill. Basic jamb width is 4-9/16 (116mm) and may be extended for different wall depths. ill is constructed of a dark bronze one-piece pulltruded fiberglass and a bronze anodized aluminum track. An integral wrapped foam sill weather-strip provides continuous seal against water and air infiltration. PANEL Panel is 1-23/32 (43.7mm) thick select kiln-dried pine using AuraLast R wood and engineered wood substrate which is water repellent preservative treated. elected panel members have Timberstrand core for added strength and dimensional stability. Wood stiles and top rail are 4-9/16 (116mm) in face width and bottom rail is 5-5/16 (135mm)in face width on 6 8 height and 8-5/16 (211mm) on 6 11 and 8 0 heights. Panels are machine clamped to insure accurate squaring of the panel and joined with coped corners secured with multiple hardwood dowel pins. AZING 3/4 (19mm) thick seed insulating glass is constructed from two panes of tempered glass, utilizing a continuous roll formed stainless steel spacer with dual seal sealant. A computer-controlled application of clear silicone is used to bed the exterior of the insulating glass into the panel. An acrylic sealant is used to bed the interior. All insulating glass units comply with the performance requirements of IGCC in accordance with either ATM E774 or E2190. GLAZING OPTION iteline Primed winging Patio Doors 3/4 insulating glass available in Low-E with Argon, Low-E, Low-E 366, Clear, Neat Glass, reflective, tinted, or obscure, tempered or other specialty glass as specified. Preserve film is a thick polyethylene film with a low tack acrylic adhesive applied to the glass for protection during shipping and installation. 4,000 foot elevations and higher require a capillary tube to equalize environmental stress (otherwise known as High Altitude glazing). High Altitude glazing does not allow the use of Argon as listed under glazing options. PRODUCT PECIFICATION: WINGING PATIO DOOR WEATHER-TRIPPING Bronze colored wrapped resilient foam weather-strip is applied to the head and side jamb of door frame and to the center mull post. A multi-flanged door sweep is applied to the bottom of both active and stationary door panels. -wing doors,weather-strip isapplied to the full perimeter of the frame, but sweep system is replaced by oak extension piece on the door panel which contacts resilient foam weather-strip on face of sill threshold. HARDWARE ingle point system with solid brass handle set activates mortise lock. Integral dead bolt provides additional security. Multi-point system also available (standard on egment Head, 8 0, 9 0 and 10 0 heights). Multi-point operates in similar fashion to single point but has two additional locking points activated by lifting up on handle after door is closed. Door handle sets may be specified Bright Brass or Antique Brass with heavy gauge mill finish strike plates. Optional handle sets come in Polished Chrome, Brushed Chrome, or Powder Coat White with stainle ke plates. Optional handle set in Oil Rubbed Bronze is also available with Oil Rubbed Bronze strike plates. Throwaway construction handle is provided with each handle set. Keyway is chlage C. EXTERIOR INECT CREEN (IN-WING DOOR ONLY) Charcoal fiberglass screen cloth (18x16 mesh) with.040 (1mm) extruded aluminum frame. tandard sliding screen available for two and three panel doors (not available on doors with ADA sill). Door screen rides on a set of two adjustable steel rollers on outside track. creen locking latch is factory-applied. An outward swing screen is available for single panel doors and is hinged the same as the door panel. Insect screens are intended to allow air and light in and to keep insects They are not intended to keep anyone or anything from falling through an open door. For safety screens or other security devices contact your local building supply retailer. GRILLE DL imulated Divided Lites) - wood muntins permanently applied to the exterior of the insulating glass unit (not available on textured glass) in 7/8 (22mm), 1-1/8 (28.5mm), or 1-3/8 (34.9mm) widths, and a putty profile in 5/8 (15.9mm), 7/8 (22mm) and 1-1/8 (28.5mm) widths only. DL is standard with a light bronze internal shadow bar to give a true divided lite appearance. As an option, DL may be ordered with a silver shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Also available is a 2-5/16 (59mm) DL bar, which simulates a double-hung checkrail. Full urround Wood Grilles - Rectangular unfinished clear pine wood grilles in 7/8 (22mm), 1-1/8 (28.6mm) and 1-3/8 (35mm) are available in patterns selected by the owner. GBG (Grille e Glass) - 5/8 (15.9mm) flat and 23/32 or 1 contour mounted between the glass panes suspended within the air cavity. Continued on next page August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-2

3 EXTERIOR TRIM 1-3/32 (27.8mm) x 2 (50.8mm) brickmould. Flat casing is available as 1-3/32 (27.8mm) x 2 (50.8mm), 1-3/32 (27.8mm) x 3-1/2 (89mm), 1-3/32 (27.8mm) x 4-1/2 (114.3mm), and 1-3/32 (27.8mm) x 5-1/2 (139.7mm). The following profiled casings are available: Williamsburg 1-3/16 x 3-1/4. Cellular foam PVC (composite) is available in standard brickmould profile or 3-1/2 flat. EXTENION JAMB Extension jambs are applied to the exterior on In-wing doors and to the interior on Out-wing doors with 21/32 (16.7mm) thick pine to accommodate wall depths up to 9-5/16 with one piece, and up to 12 with two pieces. HANDING iteline Primed winging Patio Doors wing doors may be specified as In-wing or Out-wing (9 0 and 10 0 doors available as In-wing only). Operation of door panel is viewed from exterior and should be specified according to handing callouts as specified in options section. PRODUCT PECIFICATION: WINGING PATIO DOOR ILL PAN Molded AB plastic sill pan system is recommended for use in all patio door installations. The JELD-WEN winging Door sill pan must be specified when ordering and is field-installed prior to patio door placement. INTALLATION Installation per JELD-WEN Installation Method for Wood Patio Doors JII007 or JII008. ee for instructions. PERFORMANCE NFRC Certified - (Rated and labeled in accordance with NFRC) WDMA Hallmark Certified - In accordance with AAMA/NWWDA/101/I August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-3

4 EXTERIOR FINIH PRODUCT PECIFICATION: FRENCH WINGING PATIO DOOR WEATHER-TRIPPING All exterior surfaces are covered with a factory-applied latex primer. AURALAT R WOOD AuraLast R wood is fundamentally different from wood resulting from traditional millwork preservation processes in that it uses a proprietary vacuum/pressure process to provide protection throughout the wood parts used to make windows and doors. AuraLast R wood is distinguished from wood using the current preservation methods by its unique ability to achieve greater penetration of the active ingredients into the wood parts, with a penetration of the treatment being a minimum of 92%. INTERIOR FINIH All interior surfaces are unfinished clear pine ready for on site finishing. Primed and pre-finished interiors are available in paint: Pure White, Extra White, Natural Choice, Moderate White; in stain: Wheat, Cherry, Fruitwood, Cordovan, Cider and Clear Lacquer. Frame is assembled from select kiln dried pine using AuraLast R wood on allexterior parts. Corner joints aresealed with silicone and secured with metal fasteners. Frames are finger jointed with an option for clear on most sizes. Frame thickness is 1-1/4 (31.8 mm) at head and side jamb and 11/16 (17.5mm) at sill. Basic jamb width is 4-9/16 (116mm) and may be extended for different wall depths. ill is constructed of a dark bronze one-piece pulltruded fiberglass and oak threshold. Optional pulltruded fiberglass adjustable threshold is available on operating In-wing doors. PANEL Panel is 1-23/32 (43.7mm) thick select kiln-dried pine using AuraLast R wood and engineered wood substrate which is water repellent preservative treated. elected panel members have Timberstrand core for added strength and dimensional stability. Wood stiles and top rail are 4-9/16 (116mm) in face width and bottom rail is 5-5/16 (135mm) in face width on 6 8 height and 8-5/16 (211mm) on 6 11 and 8 0 heights. Panels are machine clamped to insure accurate squaring of the panel and joined with coped corners secured with multiple hardwood dowel pins. Quad doors have two stationary and two operating panels with a center astragal applied to the secondary active panel. The primary active panel is the left center panel on quad doors (viewed from the building exterior) unless otherwise specified. GLAZING 3/4 (19mm) thick sealed insulating glass is constructed from two panes of tempered glass, utilizing a continuous roll formed stainless steel spacer with dual seal sealant. A computer-controlled application of clear silicone is used to bed the exterior of the insulating glass into the panel. An acrylic sealant is used to bed the interior. All insulating glass units comply with the performance requirements of IGCC in accordance with either ATM E774 or E2190. GLAZING OPTION iteline Primed winging Patio Doors 3/4 insulating glass available in Low-E with Argon, Low-E, Low-E 366, Clear, Neat Glass, reflective, tinted, or obscure, tempered or other specialty glass as specified. Preserve film is a thick polyethylene film with a low tack acrylic adhesive applied to the glass for protection during shipping and installation. 4,000 foot elevations and higher require a capillary tube to equalize environmental stress (otherwise known as High Altitude glazing). High Altitude glazing does not allow the use of Argon as listed under glazing options. Bronze colored wrapped resilient foam weather-strip is applied to the head and side jamb of door frame and to the center mull post. A multi-flanged door sweep is applied to the bottom of both active and stationary door panels. On Out-wing doors, weather-strip is applied to the full perimeter of the frame, but sweep system is replaced by oak extension piece on the door panel which contacts resilient foam weather-strip on face of sill threshold. HARDWARE ingle point system with solid brass handle set activates mortise lock. Integral dead bolt provides additional security. Multi-point system also available (standard on egment Head, 8 0, 9 0 and 10 0 heights). Multi-point operates in similar fashion to single point but has two additional locking points activated by lifting up on handle after door is closed. Door handle sets may be specified Bright Brass or Antique Brass with heavy gauge mill finish strike plates. Optional handle sets come in Polished Chrome, Brushed Chrome, or Powder Coat White with stainless steel strike plates. Optional handle set in Oil Rubbed Bronze is also available with Oil Rubbed Bronze strike plates. Throwaway construction handle is provided with each handle set. Keyway is chlage C. EXTERIOR INECT CREEN (IN-WING DOOR ONLY) Charcoal fiberglass screen cloth (18x16 mesh) with.040 extruded aluminum frame. creen locking latch is factory applied. An outward swing screen is available for single panel doors and is hinged the same as the door panel. Insect screens are intended to allow air and light in and to keep insects out. They are not intended to keep anyone or anything from falling through an open door. For safety screens or other security devices contact your local building supply retailer. GRILLE DL (imulated Divided Lites) - wood muntins permanently applied to the exterior of the insulating glass unit (not available on textured glass) in 7/8 (22mm), 1-1/8 (28.5mm), or 1-3/8 (34.9mm) widths, and a putty profile in 5/8 (15.9mm), 7/8 (22mm) and 1-1/8 (28.5mm) widths only. DL is standard with a light bronze internal shadow bar to give a true divided lite appearance. As an option, DL may be ordered with a silver shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Also available is a 2-5/16 (59mm) DL bar, which simulates a double-hung checkrail. Full urround Wood Grilles - Rectangular unfinished clear pine wood grilles in 7/8 (22mm), 1-1/8 (28.6mm) and 1-3/8 (35mm) are available in patterns selected by the owner. GBG (Grilles between the Glass) - 5/8 (15.9mm) flat and 23/32 or 1 contour mounted between the glass panes suspended within the air cavity. Continued on next page August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-4

5 EXTERIOR TRIM PRODUCT PECIFICATION: FRENCH WINGING PATIO DOOR ILL PAN 1-3/32 (27.8mm) x 2 (50.8mm) brickmould. Flat casing is available as 1-3/32 (27.8mm) x 2 (50.8mm), 1-3/32 (27.8mm) x 3-1/2 (89mm), 1-3/32 (27.8mm) x 4-1/2 (114.3mm), and 1-3/32 (27.8mm) x 5-1/2 (139.7mm). The following profiled casings are available: 3-1/2 (89mm) and Williamsburg 1-3/16 x 3-1/4. Cellular foam PVC (composite) is available in standard brickmould profile or 3-1/2 flat. EXTENION JAMB Extension jambs are applied to the exterior on In-wing doors and to the interior on Out-wing doors with 21/32 (16.7mm) thick pine to accommodate wall depths up to 9-5/16 with one piece, and up to 12 with two pieces. HANDING iteline Primed winging Patio Doors wing doors may be specified as In-wing or Out-wing (9 0 and 10 0 doors available as In-wing only). Operation of door panel is viewed from exterior and should be specified according to handing callouts as specified in options section. Molded AB plastic sill pan system is recommended for use in all patio door installations. The JELD-WEN winging Door sill pan must be specified when ordering and is field-installed prior to patio door placement. INTALLATION Installation per JELD-WEN Installation Method for Wood Patio Doors JII007 or JII008. ee for instructions. PERFORMANCE NFRC Certified - (Rated and labeled in accordance with NFRC) WDMA Hallmark Certified - In accordance with AAMA/NWWDA/101/I August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-5

6 QUICK PEC GUIDE: WINGING PATIO DOOR PECIFICATION TANDARD FEATURE OPTIONAL FEATURE ome options may require additional lead times. Consult your JELD-WEN ales Representative. Fingerjoint Wood Clear available on most sizes EXTERIOR FINIH Primed Natural EXTERIOR TRIM 1-3/32 Brickmould Vinyl Drip Cap INTERIOR FINIH Natural Priming Available IZE Width: OnePanel-2-6,2-9,3-0,3 2-9/16,3-6 TwoPanel-5-0,5-6,6-0,6 5-1/8,7-0 Three Panel - 7-6, 8-3, 9-0, /16, 10-6 Four Panel - 8-0, 10-0, 11-0, 12-0 idelight Width - 1-0, 1-6, 2-0 Height: 6-8, 6-11, 7-3, 8-0, 9-0, 10-0 idelight Height: 6-8, 6-11, 7-3, 8-0 GLAZING Tempered Low-E Insulating Glass Preserve Protective Film Flat Casing: 1-3/32 x 2, 3-1/2, 4-1/2, and 5-1/2 Williamsburg Casing: 1-3/16 x 3-1/4 No Brickmould Option Pre-finished Interior Options are: Paint - Pure White, Extra White, Natural Choice, Moderate White tain - Wheat, Fruitwood, Cherry, Cordovan, Cider Clear Lacquer Minimum Width: 2-0 Maximum Width: 3-6 Minimum Width: 4-0 Maximum Width: 7-0 Maximum Multi Panel Frame Width: 12-0 Minimum idelight Frame Width: 1-0 Minimum Height: 2-0 Maximum Height: 10-0 Maximum idelight Frame Height: 8-0 Clear Obscure Bronze Low-E 366 High Altitude Neat Glass Dual Low-E Reflective Tempered Additional Options for Transoms only: Decorative Glass d Craftsman d Classic d Contemporary d Estate Custom Design Capability GRILLE 5/8 Flat, 23/32 or 1 Contour GBG 7/8, 1-1/8, 1-3/8 Full urround Wood Grilles DL Bead Profile: 7/8, 1-1/8, 1-3/8, 2-5/16 with Light Bronze hadow Bar 7/8, 1-1/8, 1-3/8, 2-5/16 with ilver hadow Bar DL Putty Profile: 5/8, 7/8, 1-1/8 with Light Bronze hadow Bar 5/8, 7/8, 1-1/8 with ilver hadow Bar PANEL OPTION Lock Rail wing Door Clad Pine Bottom Panel HARDWARE ingle Point (standard up to 7 2-1/2) Multi-point optional on 7-3 heights and smaller Multi-point (standard on 8-0 and over) Multi-point (available on 6-2 and over) Continued on next page August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-6

7 QUICK PEC GUIDE: WINGING PATIO DOOR PECIFICATION HANDLE ET Antique Brass Polished Brass TANDARD FEATURE HINGE In-wing Hinges Match Handle Color Out-wing Hinges - Brushed tainless teel ILL Dark bronze one-piece pulltruded fiberglass and oak threshold HANDING Viewed from the outside OPTIONAL FEATURE ome options may require additional lead times. Consult your JELD-WEN ales Representative. Polished Chrome Brushed Chrome Powder Coat White Adjustable Hinge Available Oil Rubbed Bronze atin Nickel ADA ill Option Pulltruded Fiberglass Adjustable Threshold JAMB 4-9/16 Minimum: 4-9/16 Maximum In-wing (Exterior): 9-5/16 Exterior: Extruded Aluminum for In-wing Doors Maximum Out-wing (Interior): 9-3/8 (one piece) Interior Pine for Out-wing Doors CREEN Fiberglass Extruded Aluminum Frame CREEN COLOR Brilliant White Chestnut Bronze Desert and French Vanilla Mesa Red Hartford Green Black Arctic ilver Dark Chocolate liding screen available on In-wing doors only Hinged creen available on In-wing doors only Bronze Heirloom White Bone White Dark Buckskin moke Mocha Cream Hunter Green age Brown Redwood ea Foam Ivory Cascade Commercial Grade Kynar 500 Resin ystem August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-7

8 QUICK PEC GUIDE: FRENCH WINGING PATIO DOOR PECIFICATION TANDARD FEATURE OPTIONAL FEATURE ome options may require additional lead times. Consult your JELD-WEN ales Representative. Fingerjoint Wood Clear available on most sizes EXTERIOR FINIH Primed Natural EXTERIOR TRIM 1-3/32 Brickmould Vinyl Drip Cap INTERIOR FINIH Natural Priming Available IZE Width: TwoPanel-5-0,5-6,6-0,6 5-1/8,7-0 Three Panel - 7-6, 8-3, 9-0, /16, 10-6 Four Panel - 8-0, 10-0, 11-0, 12-0 Height: 6-8, 6-11, 7-3, 8-0, 9-0, 10-0 idelight Height: 6-8, 6-11, 7-3, 8-0 GLAZING Tempered Low-E Insulating Glass Preserve Protective Film Flat Casing: 1-3/32 x 2, 3-1/2, 4-1/2, and 5-1/2 Williamsburg Casing: 1-3/16 x 3-1/4 No Brickmould Option Pre-finished Interior Options are: Paint - Pure White, Extra White, Natural Choice, Moderate White tain - Wheat, Fruitwood, Cherry, Cordovan, Cider Clear Lacquer Minimum Width: 2-0 Maximum Width: 3-6 Minimum Width: 4-0 Maximum Width: 7-0 Maximum Multi Panel Frame Width: 12-0 Minimum Height: 2-0 Maximum Height: 10-0 Maximum idelight Frame Height: 8-0 Clear Neat Glass Obscure Dual Low-E Bronze Reflective Low-E 366 Tempered High Altitude GRILLE 5/8 Flat, 23/32 or 1 Contour GBG 7/8, 1-1/8, 1-3/8 Full urround Wood Grilles DL Bead Profile: 7/8, 1-1/8, 1-3/8, 2-5/16 with Light Bronze hadow Bar 7/8, 1-1/8, 1-3/8, 2-5/16 with ilver hadow Bar DL Putty Profile: 5/8, 7/8, 1-1/8 with Light Bronze hadow Bar 5/8, 7/8, 1-1/8 with ilver hadow Bar PANEL OPTION Lock Rail wing Door Clad Pine Bottom Panel HARDWARE ingle Point (standard up to 7 2-1/2) Multi-point optional on 7-3 heights and smaller Multi-point (standard on 8-0 and over) Multi-point (available on 6-2 and over) Continued on next page August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-8

9 QUICK PEC GUIDE: FRENCH WINGING PATIO DOOR PECIFICATION HANDLE ET Antique Brass Polished Brass TANDARD FEATURE HINGE In-wing Hinges Match Handle Color Out-wing Hinges - Brushed tainless teel ILL Dark bronze one-piece pulltruded fiberglass and oak threshold HANDING Viewed from the outside OPTIONAL FEATURE ome options may require additional lead times. Consult your JELD-WEN ales Representative. Polished Chrome Brushed Chrome Powder Coat White Adjustable Hinge Available Oil Rubbed Bronze atin Nickel ADA ill Option Pulltruded Fiberglass Adjustable Threshold JAMB 4-9/16 Minimum: 4-9/16 Maximum In-wing (Exterior): 9-1/16 Maximum In-wing (Exterior): 9-3/8 (Primed) Exterior: Extruded Aluminum for In-wing Doors Maximum Out-wing (Interior): 9-3/8 (one piece) Interior Pine for Out-wing Doors CREEN Fiberglass Hinged creen available on In-wing doors only (NOT INCLUDED IN DOOR BAE PRICE) Extruded Aluminum Frame CREEN COLOR Brilliant White Chestnut Bronze Desert and French Vanilla Mesa Red Hartford Green Black Arctic ilver Dark Chocolate Bronze Heirloom White Bone White Dark Buckskin moke Mocha Cream Hunter Green age Brown Redwood ea Foam Ivory Cascade Commercial Grade Kynar 500 Resin ystem August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-9

10 INGLE WING HANDING CALLOUT Doors pictured as viewed from exterior. Top down view shows panels as In-wing. All extension is opposite panel swing. OUT-WING OPTION: Numerical callout for Out-wing doors does not change. Add Out-wing to description and use TO callout. INIDE OUTIDE IN-WING CALLOUT # OUT-WING CALLOUT # INIDE OUTIDE T-1 T-2 T-3 T-4 T-9 T-10 T-5 TO-1 TO-2 TO-3 TO-4 TO-9 TO-10 TO-5 IN-WING CALLOUT # OUT-WING CALLOUT # T-6 TO-6 T-7 TO-7 T-8 TO-8 T-11 TO-11 T-12 TO-12 INIDE OUTIDE IN-WING CALLOUT # OUT-WING CALLOUT # T-13 TO-13 T-14 TO-14 T-15 T-16 TO-15 TO-16 INIDE OUTIDE IN-WING CALLOUT # OUT-WING CALLOUT # T-17 T-18 TO-17 TO-18 T-19 TO-19 T-20 TO-20 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-10

11 FRENCH DOOR HANDING CALLOUT OUT-WING OPTION: Numerical callout for Out-wing doors does not change. Add Out-wing to description and use FO callout. Top down view shows panels as In-wing. INIDE OUTIDE Doors pictured as viewed from exterior. All extension is opposite panel swing. IN-WING CALLOUT # OUT-WING CALLOUT # F-1 FO-1 F-2 FO-2 F-3 FO-3 F-4 FO-4 INIDE OUTIDE IN-WING CALLOUT # OUT-WING CALLOUT # F-5 FO-5 F-6 FO-6 F-7 FO-7 F-8 FO-8 INIDE OUTIDE IN-WING CALLOUT # OUT-WING CALLOUT # F-9 F-10 F-11 F-12 FO-9 FO-10 FO-11 FO-12 TATIONARY IN-WING AND OUT-WING PATIO DOOR INIDE OUTIDE IN-WING CALLOUT # OUT-WING CALLOUT # -1 O-1-1 O-1-1 O-1-1 O-1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-11

12 GENERAL INFORMATION DIMENIONAL DOOR Wood In-wing and Out-wing patio doors may be specified as dimensional, by adjusting the desired rough opening width or height in 1/4 increments from standard. Wood In-wing and Out-wing patio doors are available in single, twin, triple and quad panel doors. Transoms are available to match the variety of door sizes. INACTIVE LEFT OPERATION Wood In-wing and Out-wing patio doors are available in a full range of operating styles. ingle panel doors may be specified as stationary (non-venting) or can operate left or right. Center swing two- or three-panel doors are available with left or right operation. French doors feature two operating panels (one active, which opens first; and one inactive, which closes first), and are available in two-panel and four-panel styles. Configuration and handing is based on viewing the door from the interior. MULTIPLE AEMBLIE Wood In-wing and Out-wing patio doors are available in a wide variety of multiple panel configurations from the factory, all of which are assembled with continuous sills. Wood In-wing and Out-wing patio doors may be mulled below, or beside other wood door and wood window products. Factory assembled mulls are limited in height (100 ), width (150 ), and a total area (75 square feet). August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-12

13 INGLE WING IN-WING AND OUT-WING PATIO DOOR ELEVATION DRAWING UTILIZE A LIMITED NUMBER OF PROJECTED LINE TO PRODUCE A RUDIMENTARY DRAWING INTENDED TO BE UED IN A MALL GRAPHICAL CALE. ELEVATION ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THE TRUCTURE. IF MORE DIMENION ARE NEEDED, UE THE ECTION DRAWING FOR MORE COMPLETE DEPICTION. RO GLA 3-2 1/ / / /2 68 OUTIDE OF EXTERIOR TRIM DAYLIGHT OPENING WHD INDICATE WOOD WING PATIO DOOR WHD-3068 WHD-3068O WHD-6068F WHD-6068FO IN-WING DOOR O INDICATE OUT-WING DOOR F INDICATE FRENCH IN-WING DOOR FO INDICATE FRENCH OUT-WING DOOR BOOK CODE THE LAT TWO NUMBER INDICATE THE HEIGHT THE FIRT TWO NUMBER INDICATE THE WIDTH GENERAL WINGING DOOR NOTE 1. WOOD WINGING PATIO DOOR ARE AVAILABLE A OPERATING OR FIXED. 2. ELEVATION ARE HOWN WITHOUT EXTERIOR TRIM. IZE & MAONRY OPENING DIMENION WILL CHANGE WITH THE ADDITION OF EXTERIOR TRIM. EE THE IZING, ROUGH OPENING & MAONRY OPENING PAGE FOR EXTERIOR TRIM EFFECT. 3. OPERATING ARE AVAILABLE A LEFT OR RIGHT HAND OPERATION. 4. HANDICAP ILL, 10 1/4 BOTTOM RAIL, INTERMEDIATE LOCK RAIL AND RAIED PANEL ARE AVAILABLE FOR ALL. August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-13

14 INGLE WING IN-WING AND OUT-WING PATIO DOOR IN-WING 1-2 1/ / / / / /2 OUT-WING RO 1-0 3/ / / / / /4 7-6 GLA / / / / / / / / /2 81 WHD-1068 WHD-1068O WHD-1668 WHD-2068 WHD-2668 WHD-5068 WHD-7668 WHD-1668O WHD-2068O WHD-2668O WHD-5068O WHD-7668O WHD WHD WHD WHD WHD WHD WHD-10611O WHD-16611O WHD-20611O WHD-26611O WHD-50611O WHD-76611O WHD-1073 WHD-1073O WHD-1673 WHD-1673O WHD-2073 WHD-2073O WHD-2673 WHD-2673O WHD-5073 WHD-5073O WHD-7673 WHD-7673O Note: WHD-1080 WHD-1080O WHD-1680 WHD-2080 WHD-2680 WHD-5080 WHD-7680 WHD-1680O WHD-2080O WHD-2680O WHD-5080O WHD-7680O Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-14

15 INGLE WING IN-WING AND OUT-WING PATIO DOOR IN-WING / / /2 OUT-WING RO 2-9 3/ / /4 8-3 GLA / / / / / / / / WHD-2968 WHD-5668 WHD-8368 WHD-2968O WHD-5668O WHD-8368O WHD WHD WHD WHD-29611O WHD-56611O WHD-83611O WHD-2973 WHD-2973O WHD-5673 WHD-5673O WHD-8373 WHD-8373O Note: WHD-2980 WHD-5680 WHD-8380 WHD-2980O WHD-5680O WHD-8380O Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-15

16 INGLE WING IN-WING AND OUT-WING PATIO DOOR IN-WING 3-2 1/ / /2 OUT-WING RO 3-0 3/ / / GLA / / / / / / WHD-3068 WHD-6068 WHD-9068 WHD-3068O WHD-6068O WHD-9068O WHD WHD WHD WHD-30611O WHD-60611O WHD-90611O WHD-3073 WHD-6073 WHD-9073 WHD-3073O WHD-6073O WHD-9073O / /2 81 Note: WHD-3080 WHD-6080 WHD-9080 WHD-3080O WHD-6080O WHD-9080O Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-16

17 4-PANEL INGLE WING IN-WING AND OUT-WING PATIO DOOR IN-WING / /2 OUT-WING RO / / GLA / / / / / / / / WHD WHD-10068O WHD WHD O WHD WHD-10073O WHD WHD-11068O WHD WHD O WHD WHD-11073O WHD WHD-10080O WHD WHD-11080O Note: Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-17

18 4-PANEL INGLE WING IN-WING AND OUT-WING PATIO DOOR IN-WING /2 OUT-WING 12-3 RO / GLA / / / / / / / / WHD WHD-12068O WHD WHD O WHD WHD-12073O Note: Other panel combinations and swings may be specified. WHD WHD-12080O CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-18

19 INGLE WING COMMERCIAL WIDTH IN-WING AND OUT-WING PATIO DOOR IN-WING 3-5 1/ / /16 OUT-WING 3-5 9/ / /16 RO 3-3 5/ / / / / /16 GLA 28 9/ / / / / / / / / / /2 81 WHD-30C68 WHD-60C68 WHD-90C68 WHD-30C68O WHD-60C68O WHD-90C68O WHD-30C611 WHD-60C611 WHD-90C611 WHD-30C611O WHD-60C611O WHD-90C611O WHD-30C73 WHD-60C73 WHD-90C73 WHD-30C73O WHD-60C73O WHD-90C730 Note: WHD-30C80 WHD-60C80 WHD-90C80 WHD-30C80O WHD-60C80O WHD-90C80O Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-19

20 INGLE WING COMMERCIAL WIDTH IN-WING AND OUT-WING PATIO DOOR WITH HANDICAP ILL These doors have shorter frame and rough opening heights due to the handicap sill. IN-WING 3-5 1/ / /16 OUT-WING 3-5 9/ / /16 RO 3-3 5/ / / / / /16 GLA 28 9/ / / / / / / / / / / / / / / / / / / WHD-30C68 WHD-60C68 WHD-90C68 WHD-30C68O WHD-60C68O WHD-90C68O WHD-30C611 WHD-60C611 WHD-90C611 WHD-30C611O WHD-60C611O WHD-90C611O WHD-30C73 WHD-60C73 WHD-90C73 WHD-30C73O WHD-60C73O WHD-90C73O Note: WHD-30C80 WHD-60C80 WHD-90C80 WHD-30C80O WHD-60C80O WHD-90C80O Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-20

21 FRENCH IN-WING AND OUT-WING PATIO DOOR IN-WING 4-2 1/ /2 OUT-WING RO 4-0 3/ /4 8-0 GLA 16 3/4 16 3/ / / / / / / / / WHD-4068F WHD-4068FO WHD-40611F WHD-40611FO WHD-4073F WHD-4073FO WHD-8068F WHD-8068FO WHD-80611F WHD-80611FO WHD-8073F WHD-8073FO Note: WHD-4080F WHD-4080FO Other panel combinations and swings may be specified. WHD-8080F WHD-8080FO CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-21

22 FRENCH IN-WING AND OUT-WING PATIO DOOR IN-WING 5-2 1/ /2 OUT-WING RO 5-0 3/ / GLA / / / / / / / / WHD-5068F WHD-5068FO WHD-50611F WHD-50611FO WHD-5073F WHD-5073FO WHD-10068F WHD-10068FO WHD F WHD FO WHD-10073F WHD-10073FO Note: WHD-5080F WHD-5080FO Other panel combinations and swings may be specified. WHD-10080F WHD-10080FO CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-22

23 FRENCH IN-WING AND OUT-WING PATIO DOOR IN-WING 5-8 1/ /2 OUT-WING RO 5-6 3/ / GLA / / / / / / / / WHD-5668F WHD-5668FO WHD-56611F WHD-56611FO WHD-5673F WHD-5673FO WHD-11068F WHD-11068FO WHD F WHD FO WHD-11073F WHD-11073FO WHD-5680F WHD-5680FO WHD-11080F WHD-11080FO Note: Other panel combinations and swings may be specified. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-23

24 FRENCH IN-WING AND OUT-WING PATIO DOOR IN-WING OUT-WING RO 6-2 1/ / / / GLA / / / / / / / / WHD-6068F WHD-6068FO WHD-60611F WHD-60611FO WHD-6073F WHD-6073FO WHD-12068F WHD-12068FO WHD F WHD FO WHD-12073F WHD-12073FO Note: WHD-6080F WHD-6080FO Other panel combinations and swings may be specified. WHD-12080F WHD-12080FO CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-24

25 INGLE WING IN-WING ECTOR TOP PATIO DOOR IN-WING 2-8 1/ /2 OUT-WING RO 2-6 3/ /4 5-0 GLA / /2 MAX DROP 11 MAX DROP / / / / / / /2 MAX DROP /2 MAX DROP 11 WHD-2668 EG TOP WHD EG TOP 6-0 1/2 MAX DROP /2 MAX DROP 10 WHD-5068 EG TOP WHD EG TOP WHD-2673 EG TOP WHD-5073 EG TOP 7-0 1/2 MAX DROP /2 MAX DROP / /2 81 WHD-2680 EG TOP WHD-5080 EG TOP Note: Other panel combinations and swings may be specified. 3 & 4 Panel Radius doors are available, contact JELD-WEN for assistance. ector Top doors have multi-point hardware. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-25

26 INGLE WING IN-WING ECTOR TOP PATIO DOOR IN-WING / /2 OUT-WING RO 2-9 3/ / GLA /2 MAX DROP 11 iteline Primed winging Patio Doors 5-9 1/2 MAX DROP / / / / / / /2 MAX DROP /2 MAX DROP 11 WHD-2968 EG TOP WHD EG TOP 6-0 1/2 MAX DROP /2 MAX DROP 10 WHD-5668 EG TOP WHD EG TOP WHD-2973 EG TOP WHD-5673 EG TOP 7-0 1/2 MAX DROP /2 MAX DROP / /2 81 WHD-2980 EG TOP WHD-5680 EG TOP Note: Other panel combinations and swings may be specified. 3 & 4 Panel Radius doors are available, contact JELD-WEN for assistance. ector Top doors have multi-point hardware. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-26

27 INGLE WING IN-WING ECTOR TOP PATIO DOOR IN-WING 3-2 1/ /2 OUT-WING RO 3-0 3/ / GLA / /2 MAX DROP 11 MAX DROP / / / / / / / / /2 MAX DROP /2 MAX DROP /2 MAX DROP 11 WHD-3068 EG TOP WHD EG TOP WHD-3073 EG TOP 6-0 1/2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-6068 EG TOP WHD EG TOP WHD-6073 EG TOP WHD-3080 EG TOP WHD-6080 EG TOP Note: Other panel combinations and swings may be specified. 3 & 4 Panel Radius doors are available, contact JELD-WEN for assistance. ector Top doors have multi-point hardware. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-27

28 INGLE WING IN-WING ECTOR TOP PATIO DOOR COMMERCIAL WIDTH IN-WING 3-5 1/ /8 OUT-WING 3-5 9/ /8 RO 3-3 5/ / / /8 GLA 28 9/ / / /2 MAX DROP 11 MAX DROP / / / / / / / / /2 MAX DROP /2 MAX DROP /2 MAX DROP 11 WHD-30C68 EG TOP WHD-30C611 EG TOP WHD-30C73 EG TOP 6-0 1/2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-60C68 EG TOP WHD-60C611 EG TOP WHD-60C73 EG TOP WHD-30C80 EG TOP WHD-60C80 EG TOP Note: Other panel combinations and swings may be specified. 3 & 4 Panel Radius doors are available, contact JELD-WEN for assistance. ector Top doors have multi-point hardware. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-28

29 FRENCH IN-WING ECTOR TOP PATIO DOOR IN-WING 4-2 1/ / /2 OUT-WING RO 4-0 3/ / /4 5-6 GLA 16 3/ /2 MAX DROP 9 1/2 MAX DROP 10 iteline Primed winging Patio Doors 5-9 1/2 MAX DROP / / / / / / / / MAX DROP 9 1/2 6-5 MAX DROP 9 1/2 7-2 MAX DROP 9 1/2 WHD-4068F EG TOP WHD-40611F EG TOP 6-0 1/2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-5068F EG TOP WHD-50611F EG TOP 6-0 1/2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-5668F EG TOP WHD-56611F EG TOP WHD-4073F EG TOP WHD-5073F EG TOP WHD-5673F EG TOP WHD-4080F EG TOP WHD-5080F EG TOP WHD-5680F EG TOP Note: Other panel combinations and swings may be specified. 3 & 4 Panel Radius doors are available, contact JELD-WEN for assistance. ector Top doors have multi-point hardware. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-29

30 FRENCH AND FRENCH COMMERCIAL IN-WING ECTOR TOP PATIO DOOR ECTOR TOP PATIO DOOR COMMERCIAL ECTOR TOP PATIO DOOR IN-WING 6-2 1/2 OUT-WING 6-3 RO 6-0 3/4 6-0 GLA /2 MAX DROP 10 iteline Primed winging Patio Doors 5-9 1/2 MAX DROP / / / /8 28 9/ / / / / / / / / /2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-6068F EG TOP WHD-60611F EG TOP WHD-6073F EG TOP 6-0 1/2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-60C68F EG TOP WHD-60C611F EG TOP WHD-60C73F EG TOP WHD-6080F EG TOP WHD-60C80F EG TOP Note: Other panel combinations and swings may be specified. 3 & 4 Panel Radius doors are available, contact JELD-WEN for assistance. ector Top doors have multi-point hardware. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-30

31 9-0 INGLE WING IN-WING PATIO DOOR 2-8 1/ / /2 RO 2-6 3/ / /4 3-0 GLA / / / / /2 RO 5-0 3/ / /4 6-0 GLA / / WHD-2690 WHD-2990 WHD-3090 WHD-5090 WHD-5690 WHD-6090 Note: Other panel combinations and swings may be specified. 9-0 & 10-0 high doors are not available in Out-wing. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-31

32 10-0 INGLE WING IN-WING PATIO DOOR 2-8 1/ / /2 RO 2-6 3/ / /4 3-0 GLA / /2 105 WHD WHD WHD / / /2 RO 5-0 3/ / /4 6-0 GLA / /2 105 WHD WHD WHD Note: Other panel combinations and swings may be specified. 9-0 & 10-0 high doors are not available in Out-wing. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-32

33 9-0 INGLE WING IN-WING EGCTOR TOP PATIO DOOR 2-8 1/ / /2 RO 2-6 3/ / /4 3-0 GLA /2 MAX DROP /2 MAX DROP /2 MAX DROP / /2 93 WHD-2690 EG TOP WHD-2990 EG TOP WHD-3090 EG TOP 5-2 1/ / /2 RO 5-0 3/ / /4 6-0 GLA /2 MAX DROP /2 MAX DROP /2 MAX DROP / /2 93 WHD-5090 EG TOP WHD-5690 EG TOP WHD-6090 EG TOP Note: Other panel combinations and swings may be specified. 9-0 & 10-0 high doors are not available in Out-wing. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-33

34 10-0 INGLE WING IN-WING ECTOR TOP PATIO DOOR 2-8 1/ / /2 RO 2-6 3/ / /4 3-0 GLA /2 MAX DROP /2 MAX DROP /2 MAX DROP / /2 105 WHD EG TOP WHD EG TOP WHD EG TOP 5-2 1/ / /2 RO 5-0 3/ / / GLA /2 MAX DROP /2 MAX DROP /2 MAX DROP / /2 105 WHD EG TOP WHD EG TOP WHD EG TOP Note: Other panel combinations and swings may be specified. 9-0 & 10-0 high doors are not available in Out-wing. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-34

35 9-0 & 10-0 TALL FRENCH IN-WING PATIO DOOR 5-2 1/ / /2 RO 5-0 3/ / / GLA / / / /2 93 WHD-5090F WHD-5690F WHD-6090F 5-2 1/ / /2 RO 5-0 3/ / / GLA WHD-50100F WHD-56100F WHD-60100F Note: Other panel combinations and swings may be specified. 9-0 & 10-0 high doors are not available in Out-wing. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-35

36 9-0 & 10-0 TALL FRENCH IN-WING ECTOR TOP PATIO DOOR 5-2 1/ / /2 RO 5-0 3/ / / GLA /2 MAX DROP /2 MAX DROP /2 MAX DROP / / / /2 93 WHD-5090F EG TOP WHD-5690F EG TOP WHD-6090F EG TOP RO / / / GLA /2 MAX DROP /2 MAX DROP /2 MAX DROP 10 WHD-50100F EG TOP WHD-56100F EG TOP WHD-60100F EG TOP Note: Other panel combinations and swings may be specified. 9-0 & 10-0 high doors are not available in Out-wing. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-36

37 WING DOOR TRANOM ALIGNMENT GUIDE ONE PANEL TRANOM ONE PANEL TRANOM TWO PANEL TRANOM THREE PANEL TRANOM FOUR PANEL TRANOM CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-37

38 WING DOOR TRANOM 2-2 1/ / /2 RO 2-0 3/ / /4 4-0 GLA 16 3/4 40 3/4 16 3/ / / / / / / / / /16 WHD-2014T-1 WHD-2016T-1 WHD-4014T-1 WHD-4016T-1 WHD-4014T-2 WHD-4016T-2 WHD-2020T-1 WHD-4020T-1 WHD-4020T / /2 RO 6-0 3/ / GLA / / / / / / / / / /16 WHD-6014T -1 WHD-6016T -1 WHD-6014T-3 WHD-6016T-3 WHD-6020T -1 WHD-6020T-3 RO GLA 8-2 1/ / / / / / / / / / / / / /16 WHD-8014T-1 WHD-8016T-1 WHD-8014T-4 WHD-8016T-4 WHD-8020T-1 WHD-8020T-4 Note: Location of sash within the Transom frame matches In-wing. door panels only, see (4 9/16 jamb) or (6 9/16 jamb) for transom detail. Construction of the unit does not allow sash to be repositioned to match Out-wing panels. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-38

39 WING DOOR TRANOM 2-8 1/ /2 RO 2-6 3/ / GLA / / / / / / / / /16 WHD-2614T-1 WHD-2616T-1 WHD-5014T-1 WHD-5016T-1 WHD-2620T-1 WHD-5020T-1 RO GLA 7-8 1/ / / / / / / / / / / / /16 WHD-7614T-1 WHD-7616T-1 WHD-5014T-2 WHD-5016T-2 WHD-7620T-1 WHD-5020T-2 RO GLA 7-8 1/ / / / / / / / / / / / /16 WHD-7614T-3 WHD-7616T-3 WHD-10014T-4 WHD-10016T-4 WHD-7620T-3 WHD-10020T-4 Note: Location of sash within the Transom frame matches In-wing door panels only, see (4 9/16 jamb) or (6 9/16 jamb) for transom detail. Construction of the unit does not allow sash to be repositioned to match Out-wing panels. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-39

40 WING DOOR TRANOM / /2 RO 2-9 3/ / GLA / / / / / / / / /16 WHD-2914T-1 WHD-2916T-1 WHD-5614T-2 WHD-5616T-2 WHD-2920T-1 WHD-5620T-2 RO GLA 5-8 1/ / / / / / / / / / / / /16 WHD-5614T-1 WHD-5616T-1 WHD-8314T-3 WHD-8316T-3 WHD-5620T-1 WHD-8320T-3 RO GLA / / / / / / / / / / /16 WHD-11014T-4 WHD-11016T-4 WHD-11020T-4 Note: Location of sash within the Transom frame matches In-wing door panels only, see (4 9/16 jamb) or (6 9/16 jamb) for transom detail. Construction of the unit does not allow sash to be repositioned to match Out-wing panels. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-40

41 WING DOOR TRANOM RO 3-2 1/ / / / GLA / / / / / / / / /16 WHD WHD WHD WHD WHD WHD RO GLA 6-2 1/ / / / / / / / / / / / /16 WHD WHD WHD WHD WHD WHD RO GLA / / / / / / / / / / /16 WHD WHD Note: WHD Location of sash within the Transom frame matches In-wing door panels only, see (4 9/16 jamb) or (6 9/16 jamb) for transom detail. Construction of the unit does not allow sash to be repositioned to match Out-wing panels. CALE: 1/4 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-41

42 PANEL GLAZING OPTION 5/8 7/8 7/8 7/8 3/4 INULATED 3/4 INULATED 3/4 INULATED 3/4 INULATED 3/4 INULATED WITH 5/8 WITH 7/8 WITH 7/8 DL WITH 7/8 DL AIRPACE GRILLE FULL URROUND WITH HADOW BAR WITH ILVER PACER WOOD GRILLE 11/8 11/8 13/8 13/8 2 5/16 3/4 INULATED WITH 1 1/8 DL WITH HADOW BAR 3/4 INULATED 3/4 INULATED 3/4 INULATED 3/4 INULATED WITH 1 1/8 DL WITH 1 3/8 DL WITH 1 3/8 DL WITH 2 5/16 WITH ILVER PACER WITH HADOW BAR WITH ILVER PACER IMULATED CHECK RAIL WITH ILVER PACER BAR (HADOW BAR ALO AVAILABLE) NOTE: DL not available on textured glass. CALE 3 = 1 August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-42

43 TRIM OPTION IN-WING PATIO DOOR EXTERIOR TRIM 1 1/16 [27] 1 1/16 [27] 1 3/32 [28] 2 [51] 1 7/32 [31] 31/2 [89] 2 23/32 [69] 31/2 [89] 3 [76] BRICKMOULD FLAT CAING ADAM CAING August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-43

44 TRIM OPTION OUT-WING PATIO DOOR EXTERIOR TRIM 1 1/16 [27] 1 1/16 [27] 1 3/32 [28] 2 [51] 11/2 [38] 31/2 [89] 3 [76] 31/2 [89] 3 [76] BRICKMOULD FLAT CAING ADAM CAING August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-44

45 LITE CUT INFORMATION Wood In-wing and Out-wing patio doors are available in 7/8, 1-1/8 and 1-3/8 widths for DL (imulated Divided Lites); 5/8 Flat, 23/32 and 1 Contour GBG (Grilles between the Glass); and 7/8, 1-1/8 and 1-3/8 Full urround removable grilles. tandard lite cuts are rectangular. LITE CUT OPTION pecial lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown here represent just a few of the possibilities. Rectangular, horizontal, vertical and Prairie lite patterns are available in all standard size wood swinging patio doors. Uneven, diamond, radius and Gothic lite cuts are available, subject to approval. Approvals are based on the ability to fulfill the design requirement while maintaining the construction integrity of the finished product. RECTANGULAR HORIZONTAL VERTICAL PRAIRIE UNEVEN DIAMOND RADIU GOTHIC BAR ALIGNMENT Alignment of divided lite muntin bars from one product to the next is often required by fine architectural design. Wood grilles, GBG s, and imulated Divided Lites may be specified with muntin bars aligned. August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-45

46 GRILLE & DL LITE PATTERN PRIMED/NATURAL WING DOOR - tandard Lite Patterns Applies to all Wood Grilles, Airspace Grilles, and DL (imulated Divided Lite) INGLE WING DOOR IZE 6-8 HEIGHT 6-11 HEIGHT 7-3 HEIGHT 8-0 HEIGHT TANDARD LITE PATTERN IZE TANDARD LITE PATTERN IZE TANDARD LITE PATTERN IZE TANDARD LITE PATTERN WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H FRENCH WING DOOR IZE 6-8 HEIGHT 6-11 HEIGHT 7-3 HEIGHT 8-0 HEIGHT TANDARD LITE PATTERN IZE TANDARD LITE PATTERN IZE TANDARD LITE PATTERN IZE TANDARD LITE PATTERN WHD 4068F 2W x 5H WHD 40611F 2W x 5H WHD 4073F 2W x 5H WHD 4080F 2W x 6H WHD 5068F 2W x 5H WHD 50611F 2W x 5H WHD 5073F 2W x 5H WHD 5080F 2W x 6H WHD 5668F 3W x 5H WHD 56611F 3W x 5H WHD 5673F 3W x 5H WHD 5680F 3W x 6H WHD 6068F 3W x 5H WHD 60611F 3W x 5H WHD 6073F 3W x 5H WHD 6080F 3W x 6H ECTOR TOP WING DOOR IZE 6-8 HEIGHT 6-11 HEIGHT 7-3 HEIGHT 8-0 HEIGHT TANDARD LITE PATTERN IZE TANDARD LITE PATTERN IZE TANDARD LITE PATTERN IZE TANDARD LITE PATTERN WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD 3068 COM 3W x 5H WHD COM 3W x 5H WHD 3073 COM 3W x 5H WHD 3080 COM 3W x 6H WHD 6068 COM 3W x 5H WHD COM 3W x 5H WHD 6073 COM 3W x 5H WHD 6080 COM 3W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD W x 5H WHD W x 5H WHD W x 5H WHD W x 6H WHD 4068F 2W x 5H WHD 40611F 2W x 5H WHD 4073F 2W x 5H WHD 4080F 2W x 6H WHD 5068F 2W x 5H WHD 50611F 2W x 5H WHD 5073F 2W x 5H WHD 5080F 2W x 6H WHD 5668F 3W x 5H WHD 56611F 3W x 5H WHD 5673F 3W x 5H WHD 5680F 3W x 6H WHD 6068F 3W x 5H WHD 60611F 3W x 5H WHD 6073F 3W x 5H WHD 6080F 3W x 6H WHD 6068F COM 3W x 5H WHD 60611F COM 3W x 5H WHD 6073F COM 3W x 5H WHD 6080F COM 3W x 6H CUTOM LITE PATTERN ARE AVAILABLE NOTE: LITED LITE PATTERN ARE PER DOOR PANEL August 2010 JELD-WEN reserves the right to change specifications without notice. Page 14-46