VAV FAN POWERED TERMINAL UNITS TABLE OF CONTENTS FAN POWERED TERMINAL UNITS. C-2 Excellence in Air Distribution MODEL KQFS MODEL KQFP MODEL QFC

Transcription

1 VAV TABLE OF CONTENTS FS/ rueger models FS and fan powered terminal units were designed for optimal performance in noise sensitive applications. These series and parallel fan terminals utilize built-in attenuator sections for ultra quiet performance. FC/FV rueger models FC and FV fan powered terminal units were designed to maintain optimum temperatures in the conditioned zones through recirculation of plenum return air. The F series and parallel fan terminals offer excellent performance characteristics at an affordable cost. LPS/LPP rueger models LPS and LPP low profi le fan powered terminal units offer excellent performance and affordability in a compact unit. The LP series and parallel fan terminals were designed with optimum physical dimensions of less than 10 5/8 in unit height, which is useful where building height limits dictate shallow ceiling plenums. MODEL FS Introduction... C-4 Capacities... C-5 Exploded Views... C-7 Product Description... C-8 FS Base... C-10 FS with Hot Water Heat... C-11 Hot Water Coil Dimensional Information... C-12 Hot Water Coil Performance Data... C-13 FS with Electric Heat... C-15 Electric Heat Features & Capacities... C-16 FS Fan Curves... C-17 FS Performance Data... C-19 FS Control Information... C-21 FS Engineering Specifi cation... C-23 MODEL Introduction... C-4 Capacities... C-6 Exploded Views... C-7 Product Description... C-8 Base... C-26 with Hot Water Heat on Discharge... C-27 with Hot Water Heat on Induced Air Inlet... C-28 Hot Water Coil Dimensional Information... C-29 Hot Water Coil Performance Data... C-30 with Electric Heat... C-32 Electric Heat Features & Capacities... C-33 Fan Curves... C-34 Performance Data... C-36 Control Information... C-39 Engineering Specifi cation... C-40 MODEL FC Introduction... C-43 Capacities... C-44 Exploded Views... C-45 Product Description... C-46 FC Base, s C-48 FC Base, 7... C-49 FC Attenuator Detail... C-50 FC with Hot Water Heat, s C-51 FC with Hot Water Heat, 7... C-52 Hot Water Coil Dimensional Information... C-53 Hot Water Coil Performance Data... C-54 FC with Electric Heat, s C-56 FC with Electric Heat, 7... C-57 Electric Heat Features & Capacities... C-58 FC Fan Curves... C-59 FC Performance Data... C-61 FC Control Information... C-63 FC Engineering Specifi cation... C-65 RUEGER 2006 C-2 Excellence in Air Distribution

2 VAV FS/ ULTRA UIET INTRODUCTION: FS/ FS - FS FEATURES Ultra uiet Operation for Critical Sound Applications Airfl ow Capacities Up to 3000 CFM for Model FS and Up to 3660 CFM For Model, Providing Air Flow Control for Commercial Applications 20 Gage Galvanized Steel Casing Construction Provides Advantages in Acoustics, uality, Strength, and Product Durability Several Types of Casing Liner Options Provide uiet and Clean Operation Round Inlet s Ranging from 6 to 16 Diameter are Slightly Undersized to Fit Standard Spiral and Flex Duct for uick Installation Each Offers Multiple Primary Inlet s to Allow for Flexible System Design Fully Removable Bottom Access Panel Included with Each for Easy Accessibility to Internal Components for Maintenance Integral Induced Air Attenuator; Bolt-on Attenuator Not Required Control Enclosure Located on Left or Right-hand Side for Easier Installation Single Point Electrical Connection Minimizes the Number of Ceiling Plenum Electrical Connections Recirculation Multi-voltage Fan Motors are uiet, Reliable, and Permanently Lubricated; ECM Motors are Available Electronic Speed Control (SCR) Allows Field Adjustable Fan Airfl ow Isolated Motor/Blower Assembly Limits Casing Acoustical Transmission ETL Listings Under UL 1995 Electrical Safety ARI Listings are Certifi ed in Accordance with ARI 880 Testing Standard External Filter Option for uick Access and Routine Replacement Auxiliary Heat Offers a Wide Range of Options, Including Electric and Hot Water Heat; Offers Induction and Discharge Hot Water Confi gurations Pneumatic, Analog, and Digital Controls Can Be Customized for Many Building Systems LineaHeat Solid State Electronic Proportional Control of Electric Heat is Available with or without Leaving Air Temperature Control In today s commercial structures, sound performance is a major concern. To satisfy this concern, rueger s F line of quiet, fan powered induction terminals have been designed to provide the lowest sound levels in the industry. Through economical recirculation of plenum return air and accurate control of primary air (cooling) to the zone, these units maintain optimum temperatures in the conditioned zone. F fan terminal units also offer strong integral panel/post construction for product durability. The multi-voltage motors, blower, and primary air damper components are easily accessible from the bottom of the unit. All F units are ETL listed and ARI certifi ed. With several types of casing liners, there is a unit confi guration to meet each job specifi cation. The Model FS is designed to sustain optimum occupant comfort levels by maintaining a constant supply of air to the conditioned zone. The recirculation fan draws cold air from the primary air duct and warm air from the return plenum in proportional amounts to satisfy zone temperature requirements. Warm air and cold air blend in the unit fan before entering the discharge plenum. Optional heating coils may be used for additional terminal heating requirements. The Model features intermittent parallel fan operation and is designed to maintain optimum occupant comfort levels by supplying warm induced plenum air, cold primary air (VAV), or a mixture of both to condition the space. The fan cycles on to satisfy zone heating requirements. Optional electric or hot water heating coils provide terminal heat after the fan has cycled on. With both types of units, primary air is modulated with digital electronic, analog electronic, or pneumatic pressure independent type controls. MODEL MODEL FS - Ultra uiet, Series Type Fan Powered Terminal MODEL - Ultra uiet, Parallel Type Fan Powered Terminal RUEGER 2006 C-4 Excellence in Air Distribution

3 VAV ULTRA UIET, PARALLEL FLOW UNIT CAPACIES, UNIT CAPACITIES WITH PSC MOTOR Inlet Motor HP Motor Amps Fan 0.25" WG Primary Airflow Minimum Pressures, Ps, "WG 120V 208/240V 277V Max. Min. Max. Min. No or EH 1 Row HW 2 Row HW Pv or / or or / or or or or / or or or / or or or or / or or or or / or or , UNIT CAPACITIES WITH ECM MOTOR Inlet Motor HP ECM Motor Amps Primary Airflow ECM Fan Airflow 120V 208/240V 277V Max. Min. Max. Min or or 0 1/ or or or or or or 0 maximum primary airfl ow (CFM) is based on 1.00 WG differential pressure signal from inlet airfl ow sensor. Minimum recommended airfl ow (CFM) is based on 0.03 WG differential pressure of the inlet airfl ow sensor, or 0 cfm WG is equal to 15% 20% of the nominal fl ow rating of the terminal. Less than 15%-20% may result in greater than +/-5% control of box fl ow. To obtain Total Pressure add the ΔPv for a given CFM to the static pressure drop of the desired confi guration. (Example: size 3-10 with 1 row HW coil, = 0.82 Pt) Minimum static pressures are the difference from inlet to discharge at the maximum airfl ow with unit damper wide open. Pressures shown include losses across hot water or electric coils where applicable. Minimum pressures with water coils assume coil is on discharge of unit. See page C-34 and C-35 for complete fan curves. PSC is permanent split capacitor motor. ECM is electronically commutated motor. RUEGER 2006 C-6 Excellence in Air Distribution

4 VAV FS/ ULTRA UIET FS/ EXPLODED VIEWS FS, EXPLODED VIEW PERFORATED SOUND TRAP CONTROL ENCLOSURE PRIMARY INLET & INLET SENSOR (4 LINEACROSS SHOWN) PSC MOTOR (ECM OPTIONAL) MOTOR BLOWER ACCESS PANEL THREE-UARTER TURN LATCHES, BOTTOM ONLY (OPTIONAL) PLENUM ACCESS PANEL FORWARD CURVED FAN ELECTRIC REHEAT (OPTIONAL) FILTER CLIPS FILTER (OPTIONAL) HOT WATER COILS (OPTIONAL), EXPLODED VIEW INLET ACCESS PANEL HOT WATER COIL (OPTIONAL WITH PLENUM MOUNTING) ELECTRIC REHEAT (OPTIONAL) CONTROL ENCLOSURE PRIMARY INLET SENSOR (4 LINEACROSS SHOWN) FORWARD CURVED FAN FILTER CLIPS FILTER (OPTIONAL) BACDRAFT DAMPER RUEGER 2006 THREE-UARTER TURN FASTENERS, BOTTOM ONLY (OPTIONAL) PSC MOTOR (ECM MOTOR OPTIONAL) MOTOR BLOWER ACCESS PANEL FS - Excellence in Air Distribution C-7

5 VAV FS/ ULTRA UIET FS/ PRODUCT DESCRIPTION CASING All FS and unit casing panels are constructed of 20 gage galvanized steel. A removable bottom panel allows access to motor/blower assemblies. The unit is equipped with a backdraft damper to prevent backward fan/motor rotation. INLET COLLARS All round 22 gage inlet collars accommodate standard spiral and fl ex duct sizes. The primary air inlet is located on either the left or righthand side of the unit inlet panel of the FS or unit. (Hand is determined by looking at the unit in the direction of airfl ow with the unit in the installed position.) OUTLET CONNECTIONS All outlet connections are rectangular and require a fl anged duct connection. DAMPER ASSEMBLY All units utilize a round volume control damper with a solid shaft that rotates in self lubricating Delrin bearings. Damper blade incorporates a fl exible gasket for tight airfl ow shutoff and operates over a full 90 rotation. The damper position is marked by an arrow embossment on the end of the damper shaft. (Optional) Sterilwall Insulation: casing shall be lined with 1/2 or 1 thick, 1 1/2 lb. dual density fi berglass insulation, meeting UL 181 and NA 90A, enclosed between the unit casing and a non-perforated internal sheetmetal cover extending over the fi berglass insulation, as well as covering the liner cut edges. (Optional) Perforated Doublewall Insulation: casing shall be lined with 1/2 or 1 thick, 1 1/2 lb. dual density fi berglass insulation, (additional options: 1/2 or 1 thick, 1 1/2 lb. density foil reinforced fi berglass insulation or 13/16 thick, 4 lb. density, rigid board insulation with fi ber reinforced foil covering) meeting UL 181 and NA 90A, enclosed between the unit casing and a perforated internal sheetmetal cover extending over the fi berglass insulation, as well as covering the liner cut edges. (Optional) No Liner: casing shall be equipped with no internal insulation liner. AIRFLOW SENSOR All units are equipped with a factory installed inlet airfl ow sensor device. The standard sensor is a linear, multi-point, velocity averaging airfl ow sensor with an amplifi ed signal. (Optional) 4 LineaCross: A four-quadrant, multi-point, center averaging airfl ow sensor is also available. Balancing taps are provided to allow for easy airfl ow verifi cation. FS - INDUCED AIR INLET ATTENUATOR Integral induced air sound attenuator is a standard component for reducing radiated sound. INDUCED AIR INLET FILTER Induced air inlet fi lters (disposable, construction type) are available. These fi lters are typically used for job start-up and are provided with clip frames for easy fi lter replacement. CASING LINERS casing shall be lined with 1/2 thick, 1 1/2 lb. dual density fi berglass insulation that meets UL 181 and NA 90A. (Optional) 1 Thick Insulation: casing shall be lined with 1 thick, 1 1/2 lb. dual density fi berglass insulation that meets UL 181 and NA 90A. (Optional) Steriliner Insulation: casing shall be lined with 13/16 thick, 4 lb. density, rigid board insulation with fi ber reinforced foil covering insulation fi bers that meets UL 181 and NA 90A. Liner shall be attached to unit casing by insulation adhesive and have foil tape sealing the insulation cut edges. (Optional) Cellular Insulation: casing shall be lined with glued and riveted 3/8 thick, 1 1/2 lb. density, smooth surface, polyolefi n, closed-cell foam insulation for fi ber free application. Cellular insulation meets UL 181 and NA 90A and does not support mold or bacteria growth. (Optional) Foil Encapsulated Insulation: casing shall be lined with foil reinforced, wrapped edges, 1/2 or 1 thick, 1 1/2 lb. density fi berglass insulation that meets UL 181 and NA 90A. FAN MOTORS Fan motors for models FS, units sizes 2 to 6, and, unit sizes 2 to 7, are multi-voltage, [120, 208/240, or 277 Volt, Single-Phase] permanent split capacitor (PSC) type. Fan motor for model FS, unit size 7, is single voltage [208/240 or 277 Volt, Single-Phase] permanent split capacitor (PSC) type. s equipped with [120, 208/240 or 277 Volt, Single- Phase] electric heat have fan motors wired with the same line voltage. s with [208 Volt, Three-Phase, Three- Wire] electric heat utilize [208/240 Volt] fan motors. s with [480 Volt, Three-Phase, Four-Wire] heat are equipped with [277 Volt, Single-Phase] fan motors. [120, 208/240, or 277 Volt, Single-Phase] ECM (electronically commutated motor) fan motor is available. A motor disconnect switch is available (not available if the unit is equipped with electric heat including the doorlocking disconnect option). Motor fusing is available. FAN SPEED CONTROL All units with PSC motors are equipped with an SCR fan speed controller capable of reducing fan output by as much as 50 to 55%. All units with optional ECM motor include either a VCU or ACU speed controller. The VCU fan speed control with digital display, alternating between RPM and percentage of full fl ow, is manually fi eld set and is fi eld adjustable. The ACU control provides a means to remotely set and/or adjust the fan speed. RUEGER 2006 C-8 Excellence in Air Distribution

6 VAV FS/ ULTRA UIET FS/ PRODUCT DESCRIPTION CONTROLS Pneumatic, analog electronic, and factory mounted direct digital electronic control types are available. A no control unit is also available for fi eld mounting of electronic controls. HOT WATER HEAT The model FS coil is factory mounted to the unit discharge. Model coil is factory mounted to the induced air inlet or the unit discharge. One or two row coils are constructed of ten aluminum fi ns per inch with 5/8 O.D. sweat type connection. Left or righthand tubing connections are available. The coil tubing is water leakage tested to 400 PSIG. The standard unit access panel provides upstream cleaning capability of the coil fi ns for units with discharge mounted coils. Vent and drain option is available. ELECTRIC HEAT Heaters are ETL listed and are constructed of 20 gage galvanized steel. Available combinations are [120, 208/240, 277 Volt, Single- Phase], [208/240 Volt, Three-Phase, Three-Wire], and [480 Volt, Three-Phase, Four-Wire] See fan motor description for electric heat/fan motor combinations. Heaters for units with electronic controls include a factory supplied, mounted and wired control transformer mounted inside the electric heat enclosure. Standard heaters are equipped with automatic reset thermal cutout, magnetic contactors, airfl ow proving switch, and 80/20 Ni-Cr heating elements. Electric heater options include a fused or non-fused door interlocking disconnect switch, mercury contactors, fuseblock, manual reset cutout, and dust tight enclosure construction. LineaHeat solid state electronic proportional control of electric heat is available with or without leaving air temperature control. See page A-28 in the Engineering Section for additional information. CONTROL TRANSFORMERS Electric heat units include a factory supplied, mounted and wired control transformer, mounted inside the control enclosure for electronic control applications. Non-electric heat units with electronic controls include a factory supplied and wired control transformer mounted inside the control enclosure. RUEGER 2006 LABELS Label information adhered to each unit includes model, size, airfl ow (CFM), balancing chart, tagging data, electrical ratings, removal of fan protection packing material information, and all required agency listings. PACAGING Multiple units are palletized. Each pallet of units is banded and stretch wrapped with cellophane. FS - Excellence in Air Distribution C-9

7 VAV ULTRA UIET, PARALLEL FLOW BASE UNIT DIMENSIONAL INFORMATION BASE UNIT, INLET, PLAN, AND DISCHARGE VIEWS D H X Y A W 1 1/4" B 1 1/2" PRIMARY AIR INLET 1/2" DIAMETER DAMPER SHAFT DD 1/2" RECIRCULATED AIR INLET 20" ALLOW AT LEAST 24" CLEARANCE FOR CONTROLS HANGER BRACETS - 4 PLACES L 6 1/4 DISCHARGE J 11 7/8" INLET VIEW PLAN VIEW DISCHARGE VIEW F G Z 2 9/16" BASE UNIT, DIMENSIONAL DETAILS Max. Primary CFM Max. Fan CFM HP Inlet L W H BASE UNIT FEATURES & OPTIONS Recirculated Air Discharge D A B F G J X Y Z / /8" 36 1/8" 18 1/16" 15 1/8" 15" 5 7/8" 11" 14" 3 1/8" 9" 6" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 7 7/8" 11" 14" 3 1/8" 9" 6" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 7 7/8" 11" 14" 3 1/8" 9" 6" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 9 7/8" 11" 14" 3 1/8" 9" 7" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 9 7/8" 11" 14" 3 1/8" 9" 7" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 11 7/8" 11" 14" 3 1/8" 9" 8" 3 1/8" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 11 7/8" 15" 17" 4 1/8" 10" 8" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 13 7/8" 15" 17" 4 1/8" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 13 7/8" 15" 17" 4 1/8" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 15 7/8" 15" 17" 4 1/8" 10" 10 1/4" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 15 7/8" 15" 17" 4 1/8" 10" 10 1/4" 5 1/2" Left-hand base unit with electronic control enclosure shown; right-hand is available. STANDARD FEATURES 20 Gage Galvanized Steel Casing Construction Control Enclosure For Electronic Components 1/2 Thick, Dual Density Fiberglass Insulation Meeting NA 90A And UL 181 Safety Requirements 120, 208/240, or 277 Volt, Multi-voltage, Single-Phase, Single-Speed, Permanently Lubricated PSC Motors Field Adjustable Fan Speed Control Integral Induced Air Attenuator Motor/Blower Isolation Removable Bottom Panel Allows Easy Access to Motor/Blower Assembly and Primary Air Damper Linear Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 3 7/8 ), s 12 to 16 (DD = 5 7/8 ) Discharge Requires Flanged Duct; Connection by Others Electronic Controls Include 24 Volt Control Transformer Variety of Pneumatic, Analog, and Factory Mounted Digital Electronic Control Packages Backdraft Damper Assembly ETL Listed; Adherence to UL 1995 and CSA C22.2 No ARI Certifi ed Sound Ratings OPTIONAL FEATURES Liners: Cellular Insulation, 1 Dual Density Fiberglass Insulation, Foil Encapsulated Fiberglass Insulation, Sterilwall, Steriliner, Perforated Doublewall, or No Liner Four uadrant, Center Averaging Airfl ow Sensor; Inlet s 6-10 (DD = 5 7/8 ); s (DD = 7 7/8 ) 120, 208/240 or 277 Volt ECM Motor with VCU or ACU Controls Cam Locks (Access Panel) Motor Disconnect Recirculated Air Filter Left-hand or Right-hand Control Enclosure Hanger Brackets (Not available with Sterilwall or Perforated Doublewall liner options.) Motor Fusing Dust Tight Control Enclosure RUEGER 2006 C-26 Excellence in Air Distribution

8 VAV ULTRA UIET, PARALLEL FLOW UNIT WITH HOT WATER HEAT ON DISCHARGE DIMENSIONAL INFORMATION UNIT WITH HOT WATER HEAT ON DISCHARGE, INLET, PLAN, AND DISCHARGE VIEWS D H X Y A W 1 1/4" B 1 1/2" PRIMARY AIR INLET RECIRCULATED AIR INLET 1/2" DIAMETER DAMPER SHAFT DD 1/2" 20" ALLOW AT LEAST 24" CLEARANCE FOR CONTROLS HANGER BRACET - 4 PLACES L LEFT-HAND COIL CONNECTION SHOWN UNINSULATED COIL CASING DISCHARGE SIZES 2-4: 3 1/8" SIZES 5-7: 4 1/8" 1 & 2 ROW: 9" 1" FLANGE TYP INLET VIEW PLAN VIEW DISCHARGE VIEW 6 1/4" 11 7/8" F G Z 1 1/2" UNIT WITH HOT WATER HEAT ON DISCHARGE, DIMENSIONAL DETAILS Max. Max. Fan CFM Primary HP Inlet Recirculated Air Discharge L W H D CFM 1 Row 2 Row A B F G X Y Z / /8" 36 1/8" 18 1/16" 15 1/8" 15" 5 7/8" 15 1/8" 17" 9" 6" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 7 7/8" 15 1/8" 17" 9" 6" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 7 7/8" 15 1/8" 17" 9" 6" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 9 7/8" 15 1/8" 17" 9" 7" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 9 7/8" 15 1/8" 17" 9" 7" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 11 7/8" 15 1/8" 17" 9" 8" 2 7/8" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 11 7/8" 17 5/8" 25" 10" 8" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 13 7/8" 17 5/8" 25" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 13 7/8" 17 5/8" 25" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 15 7/8" 17 5/8" 25" 10" 10 1/4" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 15 7/8" 17 5/8" 25" 10" 10 1/4" 5 1/2" Dimensions in ( ) are mm. Left-hand base unit with electronic control enclosure shown; right-hand is available. UNIT WITH HOT WATER HEAT ON DISCHARGE FEATURES & OPTIONS RUEGER 2006 STANDARD FEATURES 20 Gage Galvanized Steel Casing Construction Control Enclosure for Electronic Components 1/2 Thick, Dual Density Fiberglass Insulation Meeting NA 90A and UL 181 Safety Requirements 120, 208/240, or 277 Volt, Multi-voltage, Single-Phase, Single-Speed, Permanently Lubricated PSC Motors Field Adjustable Fan Speed Control Integral Induced Air Attenuator Motor/Blower Isolation Removable Bottom Panel Allows Easy Access to Motor/Blower Assembly and Primary Air Damper Linear Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 3 7/8 ), s 12 to 16 (DD = 5 7/8 ) Discharge Requires Flanged Duct; Connection by Others Electronic Controls Include 24 Volt Control Transformer Variety of Pneumatic, Analog, and Factory Mounted Digital Electronic Control Packages Backdraft Damper Assembly ETL Listed; Adherence to UL 1995 and CSA C22.2 No ARI Certifi ed Sound Ratings OPTIONAL FEATURES Liners: Cellular Insulation, 1 Dual Density Fiberglass Insulation, Foil Encapsulated Fiberglass Insulation, Sterilwall, Steriliner, Perforated Doublewall, or No Liner Four uadrant Center Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 5 7/8 ); s 12 to 16 (DD = 7 7/8 ) 120, 208/240, or 277 Volt ECM Motor with VCU or ACU Controls Left-hand or Right-hand Control Enclosure Hot Water Coil Vent and Drain Motor Disconnect Recirculated Air Filter Hanger Brackets (Not Available With Sterilwall or Perforated Doublewall Liner Options) Dust Tight Control Enclosure Motor Fusing Cam Locks (Access Panel) Excellence in Air Distribution C-27

9 VAV ULTRA UIET, PARALLEL FLOW UNIT WITH HOT WATER HEAT ON INDUCED AIR INLET DIMENSIONAL INFORMATION UNIT WITH HOT WATER HEAT ON INDUCED AIR INLET, INLET, PLAN, AND DISCHARGE VIEWS D H 1" 1 1/4" FLANGE TYP B 1 1/2" X Y A W PRIMARY AIR INLET UNINSULATED COIL CASING RECIRCULATED AIR INLET RIGHT HAND COIL CONNECTION SHOWN 1 & 2 ROW: 9" 1/2" DIAMETER DAMPER SHAFT DD 1/2" 20" L ALLOW AT LEAST 24" CLEARANCE FOR CONTROLS HANGER BRACETS - 4 PLACES DISCHARGE J 11 7/8" 6 1/4" G Z F 2 9/16 INLET VIEW PLAN VIEW DISCHARGE VIEW UNIT WITH HOT WATER HEAT ON INDUCED AIR INLET, DIMENSIONAL DETAILS Max Max Fan CFM Primary HP Inlet Recirculated Air Discharge L W H 1 2 D CFM A B F G Row Row J X Y Z / /8" 36 1/8" 18 1/16" 15 1/8" 17" 5 7/8" 11" 14" 3 1/8" 9" 6" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 17" 7 7/8" 11" 14" 3 1/8" 9" 6" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 17" 7 7/8" 11" 14" 3 1/8" 9" 6" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 17" 9 7/8" 11" 14" 3 1/8" 9" 7" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 17" 9 7/8" 11" 14" 3 1/8" 9" 7" 3 1/8" / /8" 36 1/8" 18 1/16" 15 1/8" 17" 11 7/8" 11" 14" 3 1/8" 9" 8" 3 1/8" / /8" 46 1/8" 20 1/16" 17 1/8" 25" 11 7/8" 15" 17" 4 1/8" 10" 8" 5 1/2" / /8" 46 1/8" 20 1/16" 17 1/8" 25" 13 7/8" 15" 17" 4 1/8" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 17 1/8" 25" 13 7/8" 15" 17" 4 1/8" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 17 1/8" 25" 15 7/8" 15" 17" 4 1/8" 10" 10 1/4" 5 1/2" / /8" 46 1/8" 20 1/16" 17 1/8" 25" 15 7/8" 15" 17" 4 1/8" 10" 10 1/4" 5 1/2" Left-hand base unit with electronic control enclosure shown; right-hand is available. UNIT WITH HOT WATER HEAT ON INDUCED AIR INLET FEATURES & OPTIONS STANDARD FEATURES 20 Gage Galvanized Steel Casing Construction Control Enclosure for Electronic Components 1/2 Thick, Dual Density Fiberglass Insulation Meeting NA 90A and UL 181 Safety Requirements 120, 208/240, or 277 Volt, Multi-voltage, Single-Phase, Single-Speed, Permanently Lubricated PSC Motors Field Adjustable Fan Speed Control Integral Induced Air Attenuator Motor/Blower Isolation Removable Bottom Panel Allows Easy Access to Motor/Blower Assembly and Primary Air Damper Linear Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 3 7/8 ), s 12 to 16 (DD = 5 7/8 ) Discharge Requires Flanged Duct; Connection by Others Electronic Controls Include 24 Volt Control Transformer Variety of Pneumatic, Analog, and Factory Mounted Digital Electronic Control Packages Backdraft Damper Assembly ETL Listed; Adherence to UL 1995 and CSA C22.2 No ARI Certifi ed Sound Ratings OPTIONAL FEATURES Liners: Cellular Insulation, 1 Dual Density Fiberglass Insulation, Foil Encapsulated Fiberglass Insulation, Sterilwall, Steriliner, Perforated Doublewall, or No Liner Four uadrant Center Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 5 7/8 ); s 12 to 16 (DD = 7 7/8 ) 120, 208/240, or 277 Volt ECM Motor with VCU or ACU Controls Left-hand or Right-hand Control Enclosure Hot Water Coil Vent and Drain Heater Disconnect, Fused or Not Fused Hanger Brackets (Not Available With Sterilwall or Perforated Doublewall Liner Options) Cam Locks (Access Panel) Motor Disconnect Motor Fusing Recirculated Air Filter Dust Tight Control Enclosure RUEGER 2006 C-28 Excellence in Air Distribution

10 VAV ULTRA UIET, PARALLEL FLOW HOT WATER COIL DIMENSIONAL INFORMATION HOT WATER COIL, TOP AND FACE VIEWS DISCHARGE DISCHARGE 9" (229) 15/32" (12) FIN DEPTH 1 3/32" (28) 3" (76) 1" (25) MOUNTING HOLES ON THIS FLANGE SIDE ONLY TOP VIEW: 1 ROW HOT WATER COIL H PLUS 2" (51) 1" (25) FIN HEIGHT 9" (229) 15/32" (12) 12 MOUNTING HOLES 3/16" (5) FIN DEPTH 2 5/32" (55) 3" (76) 1" (25) 2 3/32" (53) RETURN SUPPLY MOUNTING HOLES ON THIS FLANGE SIDE ONLY TOP VIEW: 2 ROW HOT WATER COIL RETURN 1 5/8" (41) H D FIN LENGTH SUPPLY W WPLUS2"(51) FACE VIEW 2 CONNECTIONS 5/8" (16) O. D. 1" (25) HOT WATER COIL, DIMENSIONAL DETAILS W H D " (432) 15 1/8" (384) 13 3/4" (349) " (635) 17 5/8" (448) 16 1/4" (413) 7 Dimensions in ( ) are mm. HOT WATER COIL FEATURES & OPTIONS RUEGER 2006 STANDARD FEATURES Coils are shipped from the factory attached to the unit discharge or induced air inlet. Hot water coil is confi gured for a fl anged ductwork connection. Coil section is uninsulated. Coils are not for steam applications. Contact your rueger Representative for steam coil information. Connection Tubing - 5/8 O. D. Male Solder Coil Casing - 20 Gage Galvanized Steel Coil Tubing - 1/2 O. D. x Thick Copper Coil Fins Thick Aluminum, 10 Per Inch; Mechanically Bonded to Tubing Optional Vent & Drain Excellence in Air Distribution C-29

11 VAV ULTRA UIET, PARALLEL FLOW HOT WATER COIL PERFORMANCE DATA HOT WATER COIL PERFORMANCE DATA, SIZES 2-4, 1 & 2 ROWS Rows 2 1 Row 2 2 Rows Rows 3 1 Row 3 2 Rows Rows 4 1 Row 4 2 Rows GPM Head Airflow, CFM & Resulting MBH Loss Airside Ps Airside Ps GPM Head Airflow, CFM & Resulting MBH Loss Airside Ps Airside Ps GPM Head Airflow, CFM & Resulting MBH Loss Airside Ps Airside Ps Coil capacities are given in MBH. Head loss is given in feet of water. Air Temperature Rise (ATR) = 927 x MBH/cfm. Water Temperature Drop (WTD) = 2.04 x MBH/GPM. Coils are for hot water applications only. Coil capacities are based on 180 F entering water, 65 F entering air ( T = 115 F), and 0% Glycol. Use correction factor multipliers in chart below for other temperature differences. See -Select for other conditions.airside Ps is defi ned as the minimum static pressure at the maximum CFM with the damper full open. MBH CORRECTION FACTORS T Factor RUEGER 2006 C-30 Excellence in Air Distribution

12 VAV ULTRA UIET, PARALLEL FLOW HOT WATER COIL PERFORMANCE DATA HOT WATER COIL PERFORMANCE DATA, SIZES 5-7, 1 & 2 ROWS Head Airflow, CFM & Resulting MBH Rows GPM Loss Row Airside Ps Rows Airside Ps Head Airflow, CFM & Resulting MBH Rows GPM Loss Row Airside Ps Rows Airside Ps Head Airflow, CFM & Resulting MBH Rows GPM Loss Row Airside Ps Rows Airside Ps Coil capacities are given in MBH. Head loss is given in feet of water. Air Temperature Rise (ATR) = 927 x MBH/cfm. Water Temperature Drop (WTD) = 2.04 x MBH/GPM. Coils are for hot water applications only. Coil capacities are based on 180 F entering water, 65 F entering air ( T = 115 F), and 0% Glycol. Use correction factor multipliers in chart below for other temperature differences. See -Select for other conditions.airside Ps is defi ned as the minimum static pressure at the maximum CFM with the damper full open. MBH CORRECTION FACTORS T Factor RUEGER 2006 Excellence in Air Distribution C-31

13 VAV ULTRA UIET, PARALLEL FLOW UNIT WITH ELECTRIC HEAT DIMENSIONAL INFORMATION UNIT WITH ELECTRIC HEAT, INLET, PLAN, AND DISCHARGE VIEWS D H X Y A W 1 1/4" B 1 1/2" 1/2" PRIMARY AIR INLET 1/2" DIAMETER DAMPER SHAFT DD 31" RECIRCULATED AIR INLET DIGITAL / ANALOG CONTROL OPTION ALLOW AT LEAST 36" CLEARANCE FOR CONTROLS HANGER BRACET - 4 PLACES L 9 3/4" 6 1/4" HEATER TERMINATION ENCLOSURE 1" FLANGE DISCHARGE J 11 7/8" G Z F 2 5/16" INLET VIEW PLAN VIEW DISCHARGE VIEW UNIT WITH ELECTRIC HEAT, DIMENSIONAL DETAILS Max Max Primary Fan HP Inlet Recirculated Air Discharge L W H D A B F G CFM CFM J X Y Z / /8" 36 1/8" 18 1/16" 15 1/8" 15" 5 7/8" 11 1/2" 14 1/2" 3" 9" 6" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 7 7/8" 11 1/2" 14 1/2" 3" 9" 6" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 7 7/8" 11 1/2" 14 1/2" 3" 9" 6" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 9 7/8" 11 1/2" 14 1/2" 3" 9" 7" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 9 7/8" 11 1/2" 14 1/2" 3" 9" 7" 2 7/8" / /8" 36 1/8" 18 1/16" 15 1/8" 15" 11 7/8" 11 1/2" 14 1/2" 3" 9" 8" 2 7/8" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 11 7/8" 15" 17" 4" 10" 8" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 13 7/8" 15" 17" 4" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 13 7/8" 15" 17" 4" 10" 10" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 15 7/8" 15" 17" 4" 10" 10 1/4" 5 1/2" / /8" 46 1/8" 20 1/16" 20 1/8" 17" 15 7/8" 15" 17" 4" 10" 10 1/4" 5 1/2" Left-hand base unit with electronic control enclosure shown; right-hand is available. See next page for electric heat standard features. UNIT WITH ELECTRIC HEAT FEATURES & OPTIONS STANDARD FEATURES 20 Gage Galvanized Steel Casing Construction Control Enclosure for Electronic Components 1/2 Thick Dual Density Fiberglass Insulation Meeting NA 90A and UL 181 Safety Requirements 120, 208/240, or 277 Volt, Multivoltage, Single-Phase, Single-Speed, Permanently Lubricated PSC Motors. Field Adjustable Fan Speed Control Integral Induced Air Attenuator Removable Bottom Panel Allows Easy Access to Motor/Blower Assembly and Primary Air Damper Linear Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 3 7/8 ), s 12 to 16 (DD = 5 7/8 ) Discharge Requires Flanged Duct; Connection by Others Electronic Controls Include 24 Volt Control Transformer ARI Certifi ed Sound Ratings Motor/Blower Isolation Backdraft Damper Assembly Variety of Pneumatic, Analog, and Factory Mounted Digital Electronic Control Packages ETL Listed; Adherence to UL 1995 and CSA C22.2 No OPTIONAL FEATURES LineaHeat Solid State Electronic Proportional Control of Electric Heat Liners: Cellular Insulation, 1 Dual Density Fiberglass Insulation, Foil Encapsulated Fiberglass Insulation, Sterilwall, Steriliner, Perforated Doublewall, or No Liner Four uadrant Center Averaging Airfl ow Sensor; Inlet s 6 to 10 (DD = 5 7/8 ); s 12 to 16 (DD = 7 7/8 ) 120, 208/240, or 277 Volt ECM Motor with VCU or ACU Controls Hanger Brackets (Not available with Sterilwall or Perforated Doublewall liner options) Motor Fusing Fused or Non-fused Door Interlocking Disconnect Left-hand or Right-hand Control Enclosure Manual Reset Recirculated Air Filter Dust Tight Control Enclosure Mercury Contactors Cam Locks (Access Panel) RUEGER 2006 C-32 Excellence in Air Distribution

14 VAV ULTRA UIET, PARALLEL FLOW ELECTRIC HEAT FEATURES & CAPACITIES The kw charts below indicates the maximum and minimum safe limit capacities for each of the units and has been specifi cally designed for rueger fan powered terminals. For safe operation, the electric heater controls are interlocked with the airfl ow proving switch to allow the heater to energize only after the fan is running. Each terminal unit has been tested by ETL in accordance with UL standards. ELECTRIC HEAT STANDARD FEATURES 20 Gage Galvanized Steel Casing Construction Line Voltage Combinations: [120, 208/240, or 277 Volt, Single-Phase] [208 Volt, Three-Phase, Three-Wire] [480 Volt, Three-Phase, Four-Wire] Control Transformer for Analog and Direct Digital Controls NEMA 2 Electric Heat Control Enclosure Flanged Discharge for Field Duct Connection Single Point Connection Between the Heater and the Fan Motor (See Combinations Below) 80/20 Ni-Cr Heating Elements Automatic Reset Thermal Cutout De-energizing Magnetic Contactors Positive Pressure Airfl ow Switch OPTIONAL HEATER CONTROL LineaHeat solid state electronic proportional control of electric heat is available with or without leaving air temperature control. See page A-28 in the Engineering Section for additional information. SINGLE POINT CONNECTION COMBINATIONS ELECTRIC HEATER/FAN MOTOR [120, 208/240 or 277 Volt, Single-Phase] Electric Heat Includes Fan Motor Wired with Same Line Voltage [208 Volt, Three-Phase, Three-Wire] Electric Heat Utilizes a 208/240 Volt, Single-Phase Fan Motor [480 Volt, Three-Phase, Four-Wire] Electric Heat is Equipped with 277 Volt, Single-Phase Fan Motor kw = CFM x T ( F) 3160 Single Phase Amperes = Watts Line Voltage Three Phase Amperes = Watts Line Voltage x 1.73 When selecting electric heaters, do not exceed 120 F discharge air temperature, per NEC. The ASHRAE Handbook of Fundamentals states that discharge temperatures in excess of 90 F are likely to result in objectionable air temperature stratifi cation in the space. Also, ventilation short circuiting may occur. ASHRAE Standard 62 now limits discharge temperatures to 90 F or increasing the ventilation rate when heating from the ceiling. MINIMUM kw 1 Phase 3 Phase 120 Volt 208 Volt 240 Volt 277 Volt 208 Volt 480 Volt s Stage Stage Stage MAXIMUM kw 1 Phase 3 Phase 120 Volt 208/240 Volt 277 Volt 208 Volt 480 Volt / / / / RUEGER 2006 Excellence in Air Distribution C-33

15 VAV ULTRA UIET, PARALLEL FLOW PSC FAN CURVES PSC FAN CURVE, SIZE 2 PSC FAN CURVE, SIZE Fan Capacity (CFM) External Static Pressure ( WG) Max Min 1 Row HW 2 Row HW Fan Capacity (CFM) External Static Pressure ( WG) Max Min 1 Row HW 2 Row HW PSC FAN CURVE, SIZE 4 PSC FAN CURVE, SIZE Fan Capacity (CFM) Fan Capacity (CFM) External Static Pressure ( WG) Max Min 1 Row HW 2 Row HW External Static Pressure ( WG) Max Min 1 Row HW 2 Row HW Fan speed controller (SCR) is standard with each unit. Fan curves indicate maximum achievable fl ow reductions using SCR speed control. s must be selected to operate within the fl ow and external static pressure ranges as shown. Fan discharge air volume will be reduced approximately 5% when unit is equipped with optional factory supplied electric heat coils. RUEGER 2006 C-34 Excellence in Air Distribution

16 VAV ULTRA UIET, PARALLEL FLOW PSC FAN CURVES PSC FAN CURVE, SIZE 6 ECM FAN CURVES ECM FAN CURVE, SIZE 4 Fan Capacity (CFM) External Static Pressure ( WG) Max Min 1 Row HW 2 Row HW PSC FAN CURVE, SIZE 7 Fan Capacity (CFM) Fan Capacity (CFM) Static Pressure ( WG) 0.6 Flow Operating Range Outside Operating Range ECM FAN CURVE, SIZE 7 Fan Capacity (CFM) Static Pressure ( WG) 0.6 Flow Operating Range Outside Operating Range VCU or ACU fan speed controller is standard with each unit. Fan curves indicate the maximum and minimum achievable airfl ows. See Product Description section, page C-8 for defi nitions of VCU and ACU controllers. s must be selected to operate within the airfl ow and external static pressure ranges shown External Static Pressure ( WG) Max Min 1 Row HW 2 Row HW RUEGER 2006 Fan speed controller (SCR) is standard with each unit. Fan curves indicate maximum achievable fl ow reductions using SCR speed control.s must be selected to operate within the fl ow and external static pressure ranges as shown. Fan discharge air volume will be reduced approximately 5% when unit is equipped with optional factory supplied electric heat coils. Excellence in Air Distribution C-35

17 VAV ULTRA UIET, PARALLEL FLOW DISCHARGE SOUND PERFORMANCE DATA, DISCHARGE SOUND DATA Inlet Flow Rate Min Ps 0.5" Ps 1.0" Ps 2.0" Ps Octave Band Sound Power, Lw Lp Octave Band Sound Power, Lw Lp Octave Band Sound Power, Lw CFM (L/s) "WG (Pa) NC NC NC 100 (47) (3.1) (94) (12.4) (142) (28.0) (189) (49.8) (236) (77.8) (85) (3.3) (170) (13.2) (255) (29.6) (340) (52.7) (425) (82.3) (137) (3.5) (274) (13.8) (411) (31.1) (547) (55.3) (684) (86.5) (198) (3.4) (396) (13.7) (595) (30.9) (793) (54.9) (991) (85.7) (269) (3.7) (538) (14.7) (807) (33.0) (1076) (58.7) (1345) (91.7) (349) (3.5) (698) (13.9) (1048) (31.3) (1397) (55.6) (1746) (86.9) All sound data is based on tests conducted in accordance with ARI Ps is the difference in static pressure from inlet to discharge. Sound power levels are in db, re watts. Discharge sound power is the sound emitted from the unit discharge. NC application data is from ARI Standard Appendix E, as a function of fl ow rate shown. Dash (-) indicates a NC is less than 20. See -Select for specifi c sound data for optional liners; 1/2 dual density liner shown. See Engineering section for reductions and defi nitions. ARI rating points based on 0.25 WG external pressure. Lp ARI CERTIFICATION RATING POINTS Inlet Primary CFM Min. Ps Sound 1.5" Ps RUEGER 2006 C-36 Excellence in Air Distribution

18 VAV ULTRA UIET, PARALLEL FLOW RADIATED SOUND PERFORMANCE DATA, RADIATED SOUND DATA Inlet Flow Rate Min Ps 0.5" Ps 1.0" Ps 2.0" Ps Octave Band Sound Power, Lw Lp Octave Band Sound Power, Lw Lp Octave Band Sound Power, Lw CFM (L/s) "WG (Pa) NC NC NC 100 (47) (3.1) (94) (12.4) (142) (28.0) (189) (49.8) (236) (77.8) (85) (3.3) (170) (13.2) (255) (29.6) (340) (52.7) (425) (82.3) (137) (3.5) (274) (13.8) (411) (31.1) (547) (55.3) (684) (86.5) (198) (3.4) (396) (13.7) (595) (30.9) (793) (54.9) (991) (85.7) (269) (3.7) (538) (14.7) (807) (33.0) (1076) (58.7) (1345) (91.7) (349) (3.5) (698) (13.9) (1048) (31.3) (1397) (55.6) (1746) (86.9) All sound data is based on tests conducted in accordance with ARI Ps is the difference in static pressure from inlet to discharge. Sound power levels are in db, re watts. Radiated sound power is the sound transmitted through the casing walls. NC application data is from ARI Standard Appendix E, as a function of fl ow rate shown. Dash (-) indicates a NC is less than 20. See -Select for specifi c sound data for optional liners; 1/2 dual density liner shown. See Engineering section for reductions and defi nitions. ARI rating points based on 0.25 WG external pressure. Lp ARI CERTIFICATION RATING POINTS Inlet Primary CFM Min Ps Sound 1.5" Ps RUEGER 2006 Excellence in Air Distribution C-37

19 VAV ULTRA UIET, PARALLEL FLOW RADIATED & DISCHARGE SOUND PERFORMANCE DATA, FAN ONLY RADIATED & DISCHARGE SOUND DATA Radiated Sound Power Discharge Sound Power Flow Rate Octave Band Octave Band Lp Sound Power, Lw Sound Power, Lw Lp CFM (L/s) NC NC 150 (71) (113) (153) (193) (236) (142) (212) (283) (354) (429) (175) (260) (347) (434) (519) (236) (378) (519) (661) (802) (354) (472) (602) (727) (849) (354) (500) (649) (802) (944) All sound data is based on tests conducted in accordance with ARI Ps is the difference in static pressure from inlet to discharge. Sound power levels are in db, re watts. Discharge sound power is the sound emitted from the unit discharge. Radiated sound power is the sound transmitted through the casing walls. NC application data is from ARI Standard Appendix E, as a function of fl ow rate shown. Dash (-) indicates a NC is less than 20. See -Select for specifi c sound data for optional liners; 1/2 dual density liner shown. See Engineering section for reductions and defi nitions. ARI CERTIFICATION RATING POINTS Fan Watts Fan CFM Radiated Sound Power, Lw Discharge Sound Power, Lw RUEGER 2006 C-38 Excellence in Air Distribution