Kitchen Range. Customer Care Guide Receiving and Installing your New Kitchen. i nspiration for your kitchen

Transcription

1 Kitchen Range Customer Care Guide Receiving and Installing your New Kitchen i nspiration for your kitchen

2 Contents Section : Your Guide to Components Received Section : Fittings Guide Section 3: Handy Hints on Preparation and Installation Section 4: Installation Sequence Section 5: Finishing Touches - Door Installation Section 6: Finishing Touches - Show End Fitting Section 7: Finishing Touches - Wirework; 600 Pullout Section 8: Caring for your Kitchen Section 9: Key Unit Dimensions Important Information Before you install your Kitchen, please read the Home Delivered Products leaflet as it is used in conjunction with this guide. This leaflet has been included with this guide. Note: It is not advisable to fit timber doors in newly constructed or recently plastered rooms. A high moisture content in the environment may cause the doors to swell and split. It is recoended that doors are stored outside the kitchen until the room has dried out thoroughly. These guidelines are not a substitute for professional advice. Whilst every care has been taken to ensure that the product design, descriptions, specifications and techniques of constructing the products are accurate at the date of printing, Wickes products will inevitably change from time to time and the customer is advised to check the design, descriptions, specifications and techniques of any of the products described in this leaflet are still valid at the time of purchase or placing an order. Where these guidelines vary from the instructions on a product or its packaging, then the instructions on the product or packaging should be followed. Wickes Customer Service Our advisors at our National Customer Service Centre are dedicated to helping you to make your project a success. If you need any additional support please contact us on *. We are open: Monday - Friday: 9am - 5:30pm * For training purposes and security, our calls may be recorded. insp iration for your home

3 Section : Your Guide to Components Received Many items in the Wickes stores are made up of a number of components. This is a guide to the components you will receive. The drawing and description on the left is how the item was ordered. On the right is how the components will be shipped. Note: Certain items, Pelmet, Cornice, Plinth, Tongue and Groove End Panels and Worktops, are supplied overlength to allow clean cutting to size Ordered Item: Component Received: Important: Small items such as handles, small gallery rails and screw packs for cornice and pelmets are packed in the small parts box/bag that comes with your delivery. Cabinet Component Colour: The cabinets are supplied in an off-white coloured board. Due to variations in supply, the colour of the component panels may be different even within a single unit. Base Units Carcase Handles Additional Highline Assembly Instructions and fittings contained in this pack. Items 300 Highline Base (NRLZB3) 300 Base Cabinet (F3) 300 Highline 400 Highline Base (NRLZB4) 400 Base Cabinet 500 Highline Base (NRLZB5) 500 Base/Sink Cabinet 600 Highline Base (NRLZB6) 600 Base/Sink /Hob Cabinet (F4) 400 Highline (F5) 500 Highline (F6) 600 Highline 800 Highline Base (NRLZB8) 800 Base/Sink /Hob Cabinet x (F4) 400 Highline 000 Highline Base (NRLZB0) 000 Base/Sink /Hob Cabinet x (F5) 500 Highline 800 Highline Corner Base (NRLZB8) 800 Base/Sink /Hob Cabinet (F4) 400 Highline 000 Highline Corner Base (NRLZB0) 000 Base/Sink /Hob Cabinet (F5) 500 Highline Base Units Drawerline 300 Drawerline Base 400 Drawerline Base 500 Drawerline Base 600 Drawerline Base Carcase Assembly Instructions and fittings contained in this pack. (NRLZB3) 300 Base Cabinet (NRLZB4) 400 Base Cabinet (NRLZB5) 500 Base/Sink Cabinet (NRLZB6) 600 Base/Sink /Hob Cabinet (FB3) 300 Drawerline (FB4) 400 Drawerline (FB5) 500 Drawerline (FB6) 600 Drawerline Tandem Drawer Box x (KQQDS3T) 300 Single Drawer Set x (KQQDS4T) 400 Single Drawer Set x (KQQDS5T) 500 Single Drawer Set x (KQQDS6T) 600 Single Drawer Set Handles Additional Items 800 Drawerline Base 000 Drawerline Base (NRLZB8) 800 Base/Sink /Hob Cabinet (NRLZB0) 000 Base/Sink /Hob Cabinet x (FB4) 400 Drawerline x (FB5) 500 Drawerline x (KQQDS4T) 400 Single Drawer Set x (KQQDS5T) 500 Single Drawer Set Drawerline Corner Base (NRLZB8) 800 Base/Sink /Hob Cabinet (FB4) 400 Drawerline x (KQQDS4T) 400 Single Drawer Set 000 Drawerline Corner Base (NRLZB0) 000 Base/Sink /Hob Cabinet (FB5) 500 Drawerline x (KQQDS5T) 500 Single Drawer Set 500 Drawerline Sink (NRLZB5) 500 Base/Sink /Hob Cabinet (FB5) 500 Drawerline 600 Drawerline Sink/Hob (NRLZB6) 600 Base/Sink /Hob Cabinet (FB6) 600 Drawerline 800 Drawerline Sink/Hob (NRLZB8) 800 Base/Sink /Hob Cabinet x (FB4) 400 Drawerline Drawerline Sink/Hob (NRLZB0) 000 Base/Sink /Hob Cabinet x (FB5) 500 Drawerline x (KQQDS5T) 500 Single Drawer Set 4 3

4 Ordered Item: Base Units Drawer Pack and Pan Drawers Component Received: Carcase Assembly Instructions and fittings contained in this pack. Tandem Drawer Box Handles Additional Items 300 Drawer Pack (NRLZD3) 300 Drawer Cabinet (NRLZD5) 500 Drawer Cabinet (FD3) 300 Drawer Pack x (GRLDP3T) 300 Drawer Pack Set 500 Drawer Pack (FD5) 500 Drawer Pack x (GRLDP5T) 500 Drawer Pack Set Pan Drawer (NRLZPD6) 600 Drawer Cabinet (FPD6) 600 Pan Drawer x (GRLPD6T) 600 Pan Drawer Set Pan Drawer (NRLZPDBU9) 900 Pan Drawer/ Under Oven Cabinet (FPD9) 900 Pan Drawer x (GRLPD9T) 900 Pan Drawer Set 6/3 (NRLZPDBU9) 900 -Pan Drawer 900 Pan Drawer/ x (KQQPD9T) (FPD9) 900 -Pan Drawer 900 -Pan Drawer Set 4/ Under Oven Cabinet Drawer Curved Drawer Unit (NRLZPDBU9) 900 Pan Drawer/ Under Oven Cabinet (FPD9C) Curved 900 Pan Drawer x (GRLPD93CT) Curved Pan Drawer Set 6/3 Base Units Built-Under Oven Units Carcase Assembly Instructions and fittings contained in this pack. Handles Appliance 600 Under Oven Housing (NRLZBU6) 600 Under Oven Cabinet (FBU6) 3 x Single Oven (IN44) 44 x 896 Filler 900 Under Oven Housing (NRLZPDBU9) 900 Pan Drawer/ Under Oven Cabinet (FBU9) 03 x 896 Drawer (Stainless Steel Effect Only) Includes Drawer Box 900 Single Oven Base Units Belfast Sink Units and Butler Support Units Carcase Assembly Instructions and fittings contained in this pack. Handles Additional Items 600 Belfast Sink Unit With Door (BSSU6) 600 Belfast Sink Cabinet (FCH) x Belfast Sink Unit With Door (not available all ranges) (NRLZBSSU9) 900 Belfast Sink Cabinet x (FBS45) x Wide Butler Sink For 8 Thick Worktops (NRZLBSSU6) 600 Butler Sink Support Unit x (IN0) 0 x 596 Filler x (FCH) x Wide Butler Sink For 38 Thick Worktops (NRLZBSSU6) 600 Butler Sink Support Unit x ( FBU6 ) 3 x 596 Filler x (FCH) x ins piration for your home

5 Ordered Item: Base Units 'L' Shape Corner Base Component Received: Carcase Assembly Instructions and fittings contained in this pack. Handles Additional Items Highline 'L' Shape Corner Base 95 Corner Base Cabinet (NRLZCB9/ )Pack -Ends & Back (NRLZCB9/) Pack -Shelf Pack x (F3) 300 Highline BCF 735 Base Corner Post Highline 'L' Shape Corner Base With Carousel 95 Corner Base Cabinet (NRLZCB9/ )Pack -Ends & Back (NRLZCB9/) Pack -Shelf Pack x (F3) 300 Highline x ¾ Carousel BCF 735 Base Corner Post Drawerline 'L' Shape Corner Base 95 Corner Base Cabinet (NRLZCB9/ )Pack -Ends & Back (NRLZCB9/) Pack -Shelf Pack x (FB3) 300 Drawerline BCF 735 Base Corner Post Drawerline 'L' Shape Corner Base With Carousel 95 Corner Base Cabinet (NRLZCB9/ )Pack -Ends & Back (NRLZCB9/) Pack -Shelf Pack x (FB3) 300 Drawerline x ¾ Carousel BCF 735 Base Corner Post Base Units Corner Base / Larder Carcase Assembly Instructions and fittings contained in this pack. Drawer Set Handles Additional Items Syncromotion Drawer Corner Unit Syncromotion Cabinet (NRLZSCC )Pack -Ends & Back (NRLZSCC) Pack -Shelf Pack (FSCS) Syncromotion Set (SFK) Syncromotion Filler Kit Syncromotion Corner Drawer Set (KQQSCD) 6 Syncromotion Front Mechanism KQQSFMS x KQQSFMD x Tall Mondo Corner Unit Tall Mondo Mechanism x (FL3) 39 x 96 Door x (F3) 300 Highline TMF Tall Mondo Filler Kit Base Units Feature Units Carcase Assembly Instructions and fittings contained in this pack. Tandem Drawer Box Handles Additional Items / Optional Extras 500 Open Base (BDU5) 500 Open Base Display Unit Display Cabinet (FDF5)43 x 496 x 500 Single Drawer Set (KQQDS5T) 500 Open Base Display Unit With Wicker Basket (BDU5) 500 Open Base Display Cabinet (FDF5)43 x 496 x 500 Single Drawer Set (KQQDS5T) x 500 Wicker Baskets 50 Pull-Out Base Unit (not available all ranges) (NRLZPO5) 50 Pull-Out Cabinet (FP5) 50 Pull-Out Cabinet Pull Out Wirework Tray Unit (not available all ranges) (NRLZPO5) 50 Pull-Out Cabinet (TUF) Tray Unit Frame Single Tray (ST) 600 Concealed Drawer Unit (NRLZB6) 600 Base Cabinet 73 x 596 x 600 Easyspace Drawer (F6) (KQQZISSD6) x 600 Easyspace Drawer (KQQZISDD6) 5

6 Ordered Item: Wall Units Component Received: Carcase Handles Additional Assembly Instructions and fittings contained in this pack. Items 300 Wall Unit (NRLZW3) 300 x 735 Wall Cabinet (F3) 300 Highline 400 Wall Unit (NRLZW4) 400 x 735 Wall Cabinet (F4) 400 Highline 500 Wall Unit (NRLZW5) 500 x 735 Wall Cabinet (F5) 500 Highline 600 Wall Unit (NRLZW6) 600 x 735 Wall Cabinet (F6) 600 Highline 800 Wall Unit (NRLZW8) 800 x 735 Wall Cabinet x (F4) 400 Highline 000 Wall Unit (NRLZW0) 000 x 735 Wall Cabinet x (F5) 500 Highline 600 Corner Wall Unit (NRLZW6) 600 x 735 Wall Cabinet (F3) 300 Highline (MWC) Conversion Kit 65 Corner Wall Unit (NRLZCW6) 65 x 735 Corner Wall Cabinet (F4) 400 Highline 65 L-shaped Corner Wall Unit (NRLZCWL6) 65 x 735 Corner Wall Cabinet (FCWL6) Pair of doors 85wide (includes filler) 600 x 94 Cooker Hood Bridging Unit (NRLZCH) 600 x 94 Wall Ca binet (FAH) 90 x 596 Door 94 Feature Bridging Unit (CHF6) 600 x 94 Wall Cabinet (FCHGDA) 90 x 596 Aluminium Feature Door Included with 600 x 44 Cooker Hood Bridging Unit (NRLZCH6) 600 x 44 Wall Ca binet (FCH) x 596 Door Feature Units Carcase Assembly Instructions and fittings contained in this pack. / F rame Handles Additional Items / Optional Extras 500 Glass Wall Unit (ODU5) 500 x 735 Wall Cabinet (F5G) 500 Glass (GS) Glass Shelf 000 Glass Wall Unit (NRLZW0) 000 x 735 Wall Cabinet x (F5G) 500 Glass 500 Glass Peninsular Unit (ODU5) 500 Open Display Peninsular Cabinet x (F5G) 500 Glass (GS) Glass Shelf 500 Mixed Peninsular Unit (ODU5) 500 Open Display Peninsular Cabinet x (F5G) 500 Glass x (F5) 500 (GS) Glass Shelf 500 Standard Peninsular Unit (ODU5) 500 Open Display Peninsular Cabinet x (F5) Decorative Feature Unit ( ODU8) 800 x 584 Top Box ( ODC8) 4-Drawer Cabinet (ODF8) Frame (FHD4) Drawer Set (includes drawer boxes) Mid Height Feature Bridging Unit With Solid Door (MHF9) 900 x 367 Wall Ca binet (FMH9) 363 x 896 Door Pack of Stays (KQQSP) Certain ranges only 900 Mid Height Feature Bridging Unit With Aluminium Feature Door (MHF9) 900 x 367 Wall Ca binet (FMH9GDA) 363 x 896 Included Aluminium Feature Door with Pack of Stays (KQQSP) Certain ranges only 900 Feature Unit (FHF9) 900 Full Height Feature Cabinet (including mechanism) x (FMH9) 900 Mid Height Feature Tambour Unit (DCT) 500 Dresser/Tambour Cabinet (TM) Tambour Mechanism 6 ins piration for your home

7 7 Ordered Item: Component Received: Tall Units Carcase Handles Additional Items And Assembly Instructions and fittings 300 & 500 Larders contained in this pack. Recoended Appliances 300 Larder With Pull-Out Rack (TLEP) Larder Decorative Ends (NRLZHP3) 300 Larder (FL3) 39 x 96 Door (F3) 300 Highline 300 Pull-Out Rack Standard 300 Larder With Softclose Pull-Out Rack (TLEP) Larder Decorative Ends (NRLZHP3) 300 Larder (FL3) 39 x 96 Door (F3) 300 Highline 300 Pull-Out Rack Softclose 300 Larder With Glass Doors (TLEP) Larder Decorative Ends (NRLZHP3) 300 Larder (FL3GDA) 39 x 96 Aluminium Frame (F3GDA) 300 Aluminium Frame Included with 300 Larder With Glass and Solid Doors (TLEP) Larder Decorative Ends (NRLZHP3) 300 Larder (FL3GDA) 39 x 96 Aluminium Frame (F3) 300 Highline & Included with 500 Larder (TLEP) Larder Decorative Ends (NRLZHP5) 500 Larder (FL5) 39 x 496 Door (F5) 500 Highline 500 Larder With Standard Pull-Out Rack (TLEP) Larder Decorative Ends (NRLZHP5) 500 Larder (FL5) 39 x 496 Door (F5) 500 Highline 500 Pull-Out Rack Standard 500 Larder With Softclose Pull-Out Rack (TLEP) Larder Decorative Ends (NRLZHP5) 500 Larder (FL5) 39 x 496 Door (F5) 500 Highline 500 Pull-Out Rack Softclose 500 Larder With Swing-Out Rack (TLEP) Larder Decorative Ends (NRLZHP5) 500 Larder (FL5) 39 x 496 Door (F5) 500 Highline Swing-Out Rack Tall Units Carcase Handles Additional Items And 600 Larders Assembly Instructions and fittings contained in this pack. Recoended Appliances 600 Larder (TLEP) Larder Decorative Ends (FL6) 39 x 596 Door (F6) 600 Highline 600 Larder With Glass Doors (TLEP) Larder Decorative Ends x (FL3GDA) 39 x 96 Aluminium Frame x (F3GDA) 300 Aluminium Frame 4 Included with 600 Larder With Glass and Solid Doors (TLEP) Larder Decorative Ends x (FL3GDA) 39 x 96 Aluminium Frame x (F3) 300 Highline & Included with

8 Ordered Item: Component Received: Tall Units Carcase Handles Additional Items And 600 Larders & Appliance Housings Assembly Instructions and fittings contained in this pack. Recoended Appliances TAE6- Pair of Oven Ends* (F6) 600 Highline Tall Appliance Housing Type 'A' (FBU6) 3 x 596 Filler Panel (FAH) 584 x 596 Door Single Oven TAE6- Pair of Oven Ends* (FCH) x 596 Door Tall Appliance Housing Type 'B' (FBU6) 3 x 596 Filler Panel (FAH) 584 x 596 Door Double Ovens TAE6- Pair of Oven Ends* (FCH) x 596 Door Tall Appliance Housing Type 'C' (IN0) 0 x 596 Filler Panel (FCH) x 596 Door Upper Aperture- Microwave Lower Aperture- Single Oven TAE6- Pair of Oven Ends* (FAH) 90 x 596 Door Tall Appliance Housing Type 'D' (IN0) 0 x 596 Filler Panel (FCH) x 596 Door Upper Aperture- Single Oven Lower Aperture- Single Oven TAE6- Pair of Oven Ends* (FAH) 584 x 596 Door Tall Appliance Housing Type 'E' (FAH3) 05 x 596 Door (FCH) x 596 Door 3 Larder Fridge or Freezer Tall Appliance Housing Type 'F' TAE6- Pair of Oven Ends* (FAH3) 05 x 596 Door (FAH3) 05 x 596 Door Larder Fridge and Freezer or Fridge/Freezer Tall Appliance Housing Type 'G' TAE6- Pair of Oven Ends* (FL6) 39 x 596 Door (FA6) 600 Highline Fridge/Freezer Tall Appliance Housing Type 'H With Pan Drawers TAE6- Pair of Oven Ends* (F6) 600 Highline (FBU6) 3 x 596 Filler Panel (FPD6) 90 x 596 Drawer (FDSP6 x on certain ranges) 3 Single Oven Drawer kit KQQPD6T Tall Appliance Housing Type 'J With Pan Drawers TAE6- Pair of Oven Ends* (FCH) x 596 Door (FBU6) 3 x 596 Filler Panel (FPD6) 90 x 596 Drawer s (FDSP6 x on certain ranges) 3 Double Ovens Drawer kit KQQPD6T Tall Appliance Housing Type 'K With Drawers TAE6- Pair of Oven Ends* (FCH) x 596 Door (IN0) 0 x 596 Filler Panel (FPD6) Drawer s Upper Aperture- Microwave Lower Aperture- Single Oven Drawer kit GRLPD6T Tall Appliance Housing Type 'L' TAE6- Pair of Oven Ends* (FCH) x 596 Door (IN0) 0 x 596 Filler Panel (FAH) 584 x 596 Door Coffee Machine Compact Oven Drinks Machine Note: All Tall Units are supplied with Decorative Ends. Please read the appliance manufacturer's installation instructions before assembling the Appliance Housing. 8 ins piration for your home

9 9 Ordered Item: Component Received: Tall Units End P anels Shelf P ack Handles Additional Items And 600 Larders & Appliance Housings Assembly Instructions and fittings contained in this pack. Recoended Appliances Mid Height Larder Unit Type 'AM TAE6 Pair of Oven Ends* (FL6) 39 x 596 Door Mid Height Appliance Housing Type 'BM TAE6 Pair of Oven Ends* (FAH) 90 x 596 Door (FAH3) 05 x 596 Door Larder Fridge or Freezer (LQQAFK) 9 Filler Kit Mid Height Appliance Housing Type 'CM TAE6 Pair of Oven Ends* (FBU6) 3 x 596 Filler Panel (FA6) 600 Highline Compact Oven with accessory Drawer Microwave Coffee Machine (LQQAFK) 9 Filler Kit Mid Height Appliance Housing Type 'DM TAE6 Pair of Oven Ends* (FBU6) 3 x 596 Filler Panel (FPD6) 600 Pan Drawer 3 Compact Oven with accessory Drawer Microwave Coffee Machine x (GRLPD6T) 600 Pan Drawer Set (LQQAFK) 9 Filler Kit Mid Height Appliance Housing Type 'EM TAE6 Pair of Oven Ends* (FBU6) 3 x 596 Filler Panel (FAH) 584 x 596 Door Single Oven Compact Oven with Warming Drawer Mid Height Appliance Housing Type 'FM TAE6 Pair of Oven Ends* (FBU6) 3 x 596 Filler Panel (FPD6) 90 x 596 Drawer (FDSP6 x on certain ranges) Single Oven Compact Oven with Warming Drawer Drawer kit KQQPD6T Mid Height Appliance Housing Type 'GM TAE6 Pair of Oven Ends* (FAH) 584 x 596 Door (FA6) 600 Highline Integrated Dishwasher (LQQAFK) 9 Filler Kit Items Packed With All Necessary Components Feature Units Coents Decor Glass W all Ends Decor Ends Styles vary by range Pilasters (CAN) 600 Traditional Canopy Recoended Appliance- 600 Canopy Motor Decor Glass Wall End Universal (TCU6) 735 x 337 Wall Decor End (WP) 795 Wall Pilaster (CAN) 800 / 900 / 000 Traditional Canopy Recoended Appliance- 600 Canopy Motor Decor Glass Dresser End Left Hand (DDPGL) 795 x 337 Wall Decor End (BP) 870/890 Base Pilaster (CAN) 600 Bread Bin Canopy Recoended Appliance- 600 Canopy Motor 83 x 337 Dresser Decor End 500 Console Unit Traditional (TCU5) Supplied rigid. Decor Glass Dresser End Right Hand (DDPGR) (DP) 83 Dresser Pilaster 600 Console Unit Traditional (TCU6) Supplied rigid. 890 x 600 Base Decor End (WSU) Wall End Wing Unit Sometimes supplied rigid. Left or right handed in some ranges. 400 x 600 Tall Decor End (TP) 400 Tall Pilaster (Certain Ranges) (BSU) Base End Wing Unit Sometimes supplied rigid. Left or right handed in some ranges.

10 Other Items Available As Optional Extras Options Packed In Separate Boxes: Feature Units Frames Accessories F or F eature Units (All options are not available in all ranges) Coents (ODU3) 300 Open Base & Wall Unit (ODF3) Frame For 300 Open Unit (735 High) (GRO) Gallery Rail For Open Units ( pair) (FT3) 300 Fretwork (WRS) Wine Rack With Scallops (GRO) Gallery Rail For Open Units ( pair) (WRS) Wine Rack With Scallops (ODU5) 500 Open Base & Wall Unit (GRO) Gallery Rail For Open Units ( pair) (FT5) 500 Fretwork (GS) Glass Shelf For 500 Open Shelf (BDU5) 500 Open Base Display Unit (F5G) 500 Glass Door (PRG) Plate Rack and Gallery Rail Handle supplied separately Gallery Rail not supplied on certain ranges (WRG) Wine Rack and Gallery Rail Gallery Rail not supplied on certain ranges (FHD) Herb Drawers Handles supplied separately (ODF5) Frame For 500 Open Unit (735 High) (GRO) Gallery Rail For Open Units ( pair) (PRG) Plate Rack and Gallery Rail (WRG) Wine Rack and Gallery Rail (HDF5) Frame For 500 Open Unit (588 High) (GRO) Gallery Rail For Open Units (FHD) Herb Drawers Handles supplied separately (GRO) Gallery Rail For Dresser ( pair) (DCT) 500 Dresser/Tambour Cabinet (FT5) 500 Fretwork (GS3) Glass Shelf For Dresser (FHD) Herb Drawers Handles supplied separately (DR5) Dresser Drawer Handle supplied separately (FDR) 500 Glass Door For Dresser Handle supplied separately (WR) 50 Wine Rack (SD) Pack of 5 Spice Drawers (WSU) 300 Wall End Wing Unit (FTW) Fretwork For Wall End Wing (WGR) Gallery Rails For Wall End Wing (BSU) 300 Base End Wing Unit (FTB) Fretwork For Base End Wing (BGR) Gallery Rails For Base End Wing Supplied either left or right handed (BSU) 300 Base End Wing Unit (BGR) Cornice/Pelmet for Quad Unit (BGR) Plinth for Quad Unit (BGR) Left-hand Cornice for Quad Unit (BGR) Right-hand Cornice for Quad Unit (BGR) Pelmet for Quad Unit (BGR) Plinth for Quad Unit 0 ins piration for your home

11 Section : Fittings Guide Shown on this page are illustrations of the fittings that are used in assembling your new kitchen. All the fittings included with each unit will be on this page. Refer to the illustrations in the assembly instructions to determine which is the correct list for that unit. Please study this list so as you will recognise the fittings as you open the boxes. Most items are not shown full size, however, Ref. No. Cam Permafix Block Cover Cap (White) 570 Wall Hanging Plate Tandem Dresser Drawer Side (P air) LH-5385 RH Hinge Arm Cover Cap 555 Item Ref. Ref. No. Item No. Item Metal Shelf Support 5 Euro Screw Hinge Arm Cover Cap x 7 Tandem F ascia Bracket Aluminium F eature Door Hinge Plate Mini-fix Bolt Jointing Plate 5404 Glass Shelf Support Cover Cap (Cream) Wall Hanging Bracket LH-546 RH-547 Wall Hanging Bracket Cover Tandem Dresser Drawer Runner (P air) LH-5387 RH-5388 Hinge Plate x x 3 LH-548 RH-549 Tandem Cover (P air) LH-5366 RH Hinge 560 Dowel the screws are shown approximately full size. Not all of these parts will be used in every kitchen. Refer to the Assembly Leaflets for actual number and types of fittings required for each unit or housing. If it is necessary for you to telephone the customer service team, please limit confusion by referring to the parts by the name and reference number (i.e. Ref.54076) shown. Universal Fixing Bracket Screw-on Half Block Cover Cap (Light Oak) x 5 Carcase Connecting Bolt x Cover Cap x x 45 Carcase Screw Tandem Drawer Bracket (P air) 4.5 x 55 Carcase Screw 5098 Tandem P an Drawer Bracket LH-5359 RH Tandem Drawer Side (P air) LH-5380 RH-538 Tandem Pan Drawer Gallery Rail Hinge Ref. No. Soft-close Buffer 00 Hinge Soft-close Buffer 70 Hinge Tandem Drawer Runner (P LH-5390 RH-539 Tandem P an Drawer Box Side 5384 Item Door\Drawer Buffer 5999 Quad Unit 00 Hinge (unsprung) 570 air) Aluminium F eature Door Hinge 564 Aluminium F eature Door Stay 5406 Quad Unit Soft Close Striker Plate 573 Leg socket Quad Unit Soft Close Buffer 57 Plinth Clip Quad Unit Soft Close Holder 57 Adjustable Leg

12 S ection 3 : Handy Hints on Preparation and Installation Please spend 5 minutes reading this section before coencing to assemble and install your new kitchen. CAUTION! Some pieces of hardware could be hazardous to small children. K eep all these items out of reach and do not leave children unattended in the assembly area. Many of the units, particularly the double door units and tall units, are heavy and should be lifted with caution. To reduce the risk, do not fit doors or drawers until the units have been attached to the walls. D O N O T U S E A K N I F E T O O P E N T H E B O X E S A S T H I S M AY DA M A G E T H E C O N T E N T S. Read the plans Find and review the plans and any other drawings used to prepare your order. Pay particular attention to any units that have special features such as aluminium legs or will be positioned unusually. Preparation Before starting any assembly, spend some time preparing the area where the units will be fitted. To get long term use and performance from our products, make sure the kitchen is installed by a competent DIYer. To help your project run smoothly, make sure your contractor understands the measurements and dimensions before you start work. After checking that all the units you ordered have been delivered, the area should be stripped out and any obstructions such as old skirting, disused pipes, tiles etc. removed. It is not advisable to fit timber doors in newly constructed or recently plastered rooms. High moisture content in the environment may cause the doors to swell and split. Don t store your products in and unsuitable place or on hard surfaces such as concrete etc. as they may get damaged. Services If you wish to fit or move any electric, gas or water points, now is the time to do this. Services to appliances should be to the manufacturer's specification and fitted by a qualified person. There are many Wickes Good Ideas Leaflets to help you in this so please ask a Design Consultant in any of our Wickes stores. Our designers have created clear, easy-to-follow instructions but, if you have any difficulties, please call our customer service team who can help at any stage of the process. ins piration for your home

13 Walls and floor Make sure all plaster work is sound particularly where the units will be attached. This is between 800 & 870 up the wall for base units and between 00 & 00 from the floor for wall units. It is important to make sure all plaster is dry before fitting units as damage may occur to the units. Floors should be sound and able to take the weight of the units and appliances. Not all walls are straight, plumb or square. However, in most cases, this can be overcome by using thin pieces of wood between the unit and the wall. Decorating Although the units will cover a large amount of the floors and walls, it may well be easier to decorate the areas of the walls, ceilings and floor that will show around the units before installation. This is particularly true of the wall and ceiling above the wall units and the space between the base and wall units. If tiles are to be fitted, it is recoended that this is done after the units and worktop have been installed. Tools The following tools are necessary for assembling and installing the units: Pozidrive No (cross head) screwdriver; 5 flat screwdriver; Metric tape measure; square; spirit level; electric drill with 8, 5, 3 diameter wood drillbits and appropriate masonry drillbits; panel and jig saw; bradawl; mallet; G-clamps (minimum of two); mitre block and mitre saw; work bench or firm work surface. Basics Protect the finish on panels by laying them on the floor and using the packaging to prevent scratches. Do not overtighten screws and be particularly careful when using power screwdrivers. Make sure that all the parts and hardware have been enclosed, contact your supplier if there is anything missing or damaged. First-time assemblers All the units have been designed for easy assembly. First-time assemblers should start by assembling a small unit such as a single door base unit to familiarise themselves with the fittings. Read the assembly instructions carefully before starting assembly and complete one unit before starting the next. It is advisable to leave all of the facias, drawer boxes, plinth, cornice and worktops in a separate room whilst assembling and installing the units. 3

14 5 55 Section 4: Installation Sequence Step - Get ready Read the Handy Hints pages. Check the plans for the new kitchen. Step - Start in a corner Fit any special features (such as decorative feet or replacement ends) before installing the unit and note where these units are positioned on the plans. Try assembling a small unit to familiarise yourself with the procedure. Carousel Top Panel Drilling Carousel Bottom Panel Drilling Begin in a corner. If a Corner Unit is to be fitted, assemble and position this unit in the corner. If the units are to be fitted between two corners, refer to the plan to see which corner is the starting point. The units illustrated on the right are all coonly used to start a run of units in a corner. If the kitchen does not fit up to a corner, remember to allow for End Wings or Show Ends when positioning the first unit. Standard Base Unit This will begin a straight run of units x 95 Corner Unit The shelf or carousel must be fitted before installation. To fit the carousel, it is necessary to drill a 5 diameter hole in the top and bottom panel in the locations shown in the illustration. Unit Width X 65 Corner Base Unit Follow installation instructions with the unit for the correct position in the corner. Appliance Housing, Broom Cupboard or Larder This will begin a straight run of units. Step 3 - Tall units Step 4 - Assemble and position the base units Assemble the tall units and place in position Level Assemble any remaining base units and place in position. Sink units should be cut as necessary for the plumbing. Find the lowest point on the floor. The legs on the unit in this position should be 40 high plus the thickness of any flooring that will be underneath the plinth. Level the remaining base units, working away from this unit. Level Floor Covering 40 Plinth Floor 4 ins piration for your home

15 5 Step 5 - Connect the base units and fix to the wall 5 Once the units are correctly positioned, start in a corner and fix the units to the wall and connect them together. Fix to the wall with the supplied brackets. Use plugs or other suitable fixings of the correct type for the wall construction. Tall and appliance units in particular, must be securely fixed. If in any doubt, consult an expert. The connecting bolts used to connect the units together can be hidden by putting them adjacent to the hinge plate, shelf or drawer runner. Drill G-clamps Clamp the units together. Decide where to locate the connection bolts. This shows the hole being drilled behind a hinge location. Drill through with a 5 wood drill into a piece of scrap wood. Push in the bolt and tighten the screw. Alternative position above a drawer runner. Please use suitable fixings (not supplied) Plasterboard Fixing- Not suitable for many units. See notes. Mark the position for drilling. Move the bracket out of the way. Drill using a bit suitable for the wall and the size of wall plug. Fit the plug. Put the bracket back in position and fit a suitable screw. Plasterboard is not strong enough to support wall or tall units so plasterboard fixings are not suitable for fixing those units but are acceptable for base units only. Tall units, especially ones with appliances, need to be very securely fixed to the wall. If necessary fit a batten to studs within the wall and then fix the unit to the batten. Step 6 - Mark a line for the wall hanging plates. Centreline Screw Slots Centreline Screw Slots 64 Mark a line around the room at the height for the wall hanging plates. Kitchens with Tall units: measure 64 down from the top of the Tall Unit. Kitchens without Tall units: measure 9 up from the floor. If there are Dressers units, make sure there is 59 between the line and the top of the base units Dresser Position

16 Step 7 - Assemble and fit the corner wall units. 0 0 CAUTION! people are required for this stage. Centreline Screw Slots Assemble the corner wall unit. There is two types of corner wall unit. Installation is the same for both types. Fix the wall hanging plates to the wall as shown in the instructions. They are fitted to the wall 0 in from the outside edge of the unit. Use plugs or other suitable fixings of the correct type for the wall construction. Wall hanging plates must be securely fixed to the wall. If necessary, fit a batten to studs within the wall and then fix the plates to the batten. If in any doubt, consult an expert. Hang the unit on the plates. This needs people. Don't adjust the hanging bracket at this stage. 65 Corner Wall L - shaped Corner Wall Plasterboard Fixing- Not suitable for wall units. See notes Step 8 - Assemble and fit the remaining wall and feature units. Assemble the remaining wall units and accessories Hang the remaining wall units. Level the wall units by adjusting the wall hanging brackets and fit the covers. Fix the standard units together with connecting bolts. See Step 5. Feature Units and Accessories are connected with 3 screws fitted from the adjacent units instead of connecting bolts. After fixing, tighten the units to the wall. Drill G-clamps Fitting Accessories Use 3 screws to connect the accessories to the other units. Countersinking the screws allows them to be fitted behind hinge plates, shelves or drawer runners. Use a 3 drill to make 30 deep pilot holes. Do not drill through both units x 3 6 ins piration for your home

17 70 Step 9 - Fit Show Ends and Worktops. If Show Ends have been ordered, fit them now. See page 9 for details. Cut the worktops to the correct size and apply edging. Mark and cut out the holes for the sinks and hobs. Fit the worktops. At the front, the worktop is held in place by screws through the front rails. At the rear, use roundhead screws through the brackets. Fit the hob. Refer to the manufacturer s handbook. Fit the sink. Finish plumbing. Worktops Cutting- It is recoended that the surface of the laminate is scored with a knife and then cut with a fine toothed saw. Take great care moving a worktop with a sink cut-out as the cut-out makes it weak. Sealing- All cut edges where raw chipboard is exposed on both the worktop and the carcase must be sealed with a moisture resistant sealer such as gloss paint, varnish or silicone sealant. Edging- If aluminium end caps/jointing strips are to be used, the cut edge should be sealed. The edging strip supplied with the worktop should be glued to the cut end with contact adhesive. Excess edging can be tried off using a metal file. 4.5 x x 3 Over - hang Step 0 - Fit Dressers, Cornice and Pelmet,Appliances. Fit the dressers. Tile the walls and finish decorating. Mitre and fit the cornice and light pelmet. Fit Fretwork and Galleries etc. Fit remaining appliances. Refer to the manufacturer s instructions for information. Pay particular attention to note on ventilation. Cornice and Pelmet The Cornice and Pelmet should be cut using a mitre block and saw. Follow the diagram for the correct angles. Different styles of Cornice and Pelmet are fitted in slightly different positions. See the illustration for guidance. Section A-A shows the view from the side and how the items overhang the doors. Section B-B shows the view from the front and how the items overhang the sides. Drill 5 holes or attach half blocks 50 in from each end and every 450 along straight sections. Section A-A (Side View) B-B (Front View) Door 0 Section A-A (Side View) B B-B (Front View) 5 90 Door B B-B (Front View) 45 A A Section A-A (Side View) Section A-A (Side View) B-B (Front View) Door Door Door Door 0 Wear a suitable dustmask when cutting MDF Newel Post The Newel Post is fixed flush at the front corners of the unit. The Pelmet must be fixed with at least enough setback to cover the ends completely. Wall Unit Underside 7

18 Step - Flooring and Plinth Lay flooring. The flooring usually stops at the legs but will need to continue under units with decorative legs. Fit the plinth. The plinth may need to be tried to allow for irregularities in the floor. A return plinth is made from a section of Continuous Plinth. It will need to be notched to fit around the legs. It is fitted behind the plinth along the front. Any cut edges should be covered with the supplied edging tape using contact adhesive. On the return, fit the plinth clips the other way up to avoid clashing with the plinth clip on the front. Floor Covering Return Plinth Trim to suit the wall 40 Plinth Floor = = = = Continuous Plinth Edging Tape Step - Fit the Doors and Drawers. Assemble and fit the drawer boxes. Fit the shelves. Hang the doors. Refer to pages 0 and for more information. Refer to information included with the appliance for information on fitting integrated appliance doors. Fit the Softclose buffers. Smaller doors need only Softclose buffer with a cover cap for the other hinge. Larger doors use Softclose buffers. Refer to the assembly instructions. Fit the drawer fronts. Drill the doors and drawer fronts for the handles. Refer to page for more information. 8 ins piration for your home (if required)

19 Section 5: Finishing Touches - Show End Fitting Scribing to the Wall Position the unit. Clamp the Show End to the unit so that it is just touching the wall. Measure the overhang at the front of the unit and subtract the amount needed to overhang the door. Cut a small block of wood to this size and by placing it Wall and Dresser Units The Show End is supplied 53 deeper than the carcase to allow for scribing to the wall at the back and overhanging the door at the front. The amount of overhang depends on the thickness of the door. The bottom of the Show End can either be left to enclose the pelmet (Option A) or the top (Option B) Over - hang against the wall, draw a line parallel to the wall onto the Show End. Trim the Show End along the line. If desired, the fit can be tested on a piece of the packaging before cutting the Show End. tried so that the bottom of the Show End is flush to the bottom of the unit and the pelmet fitted underneath the Show End (Option B). See Page 5 for hints on concealing the screws. Scribe to the wall x 3 (Option A) (Option B) x4/ Show End Bottom of Wall Unit Base Units and Tall Units The show end needs to be cut down to suit the height of the unit once it has been installed. The show end should overhang the front of the carcase and continue to the floor. The Show End is supplied 30 deeper than the carcase to allow for scribing to the wall at the back and overhanging the door at the front. The amount of overhang depends on the thickness of the door. The bottom and back can be scribed to the floor and wall and the raw edge must be sealed with a suitable sealer. See Page 5 for hints on concealing the screws. Trim to correct height 5 Over - hang Over - hang 5 Scribe to the wall Scribe to the wall 4.5 x 3 x4/ Show End 4.5 x 3 x8/ Show End 9

20 Section 6: Finishing Touches - Door Installation Please spend 5 minutes reading this section after the units have been assembled and fitted but before you start to fit the doors. Unpacking For timber doors, drawer fronts and accessories The doors, drawer fronts and some accessories of your new kitchen are manufactured from carefully selected solid timber/veneers of the finest quality. As with most things in nature, there is a degree of variation in both colour and graining. These differences are part of the special character and beauty of wood, differences which make a wood kitchen such a desirable product. Any large differences in tone apparent when your kitchen is first unpacked will diminish over a few months as the timber mellows with exposure to daylight to give a natural uniformity. Installation For the best results, the doors and drawer fronts should be checked together. After unpacking, and before installing doors and drawers, it is recoend that they are placed against their respective units, in order to judge the final effect. Reposition any items to obtain the most even match. Note: It is not advisable to fit timber doors in newly constructed or recently plastered rooms. A high moisture content in the environment may cause the doors to swell and split. It is recoended that doors are stored outside the kitchen until the room has dried out thoroughly. Hinges and Drawers Once you are happy with the overall effect, fit the hinges and drawer boxes. Attach doors and drawers to the cabinets taking care not to damage the lacquered surfaces. When all items are installed and you have checked the results, attach the handles. Handles Check one more time before drilling, place a piece of scrap wood behind the hole to prevent splintering then using a 5 drill, carefully drill through. Fit handles taking care not to let the screwdriver slip. See inside this leaflet for more information. Please note: Any doors or drawer fronts which have been fitted with hinges or drilled for handles cannot be returned to the supplier. Self - Adhesive Edging Tape Self- adhesive edging tape is available to colour match the doors. It is fitted before attaching the doors. The edge of the carcase must be clean, dry and free from dust and grease. Apply the tape carefully to the front edge. Press the tape down firmly with a clean hard roller or smooth bar to ensure good adhesion. Trim any excess with a sharp knife. 0 ins piration for your home

21 Door Installation Door Adjustment Please Note: The door on a single door unit may open either left or right. Before attaching hinges to the door, choose which opening is wanted and fit hinges to the appropriate side. A B C x /door A- V ertical B - Lateral C - Horizontal Loosen screw 'A' on all Loosen screw 'B'. Adjust Loosen screw 'B' ½ turn. hinges. Adjust door and door and retighten screw. Turn screw 'C' until door is retighten screw. positione d correctly and retighten screw 'B'. Standard Hinge A Corner Unit Hinge B C A Aluminium Feature Door B C x/hinge 3.5 x 3 (if required) A B C Door and Drawer Handle Drilling Please Note: All doors and drawers are pin marked on the back for a handle. Because some Use a 5 flat-tipped drill bit and drill into a piece of doors are reversible, they are pin marked in several places. Please decide the handle position on scrap wood to prevent splintering. all units and check all details carefully before drilling as drilled doors and drawer fronts cannot be It is recoended that the doors and drawers are fitted returned. before drilling. Base Units (Top of Door) Drawer Fronts Scrap wood Wall Units (Bottom of Door) 5 Wood Drill Bit

22 Section 7: Finishing Touches - Wirework Wire Door Mounted Racks (Items may be different than illustrated) These racks are suitable for 500 or 600 wide doors, Please read the fitting notes below. Spice Rack Important P oints Double Bottle Rack Single Bottle Rack Some doors have very thin sections in the centre or on the edges. The screws supplied may not be suitable for all doors. Note the position of shelves when positioning the rack. Do not overload the racks as this may damage the rack and the hinges. Wicker And Wire Baskets Shallow Baskets are 00 deep; Deep Baskets are 00 deep. Baskets can be fitted to 500 wide Highline Units, 500 wide Drawerline Units and 500 wide Larders. The following illustrations should be used as a guide only. Please check fitting before installing the baskets. 3.5 x x 6/Basket x /Basket Pull-out Unit 735 High End Panel Highline positions I I Door drilling and Bracket positions 0 Dia. x deep 7 Bradawl Important- This unit uses the components from the Easy Space kit. The upper two drawers are concealed drawers and assembled using the Easy Space instruction sheet. The bottom drawer is assembled the same way but the door fascia is fitted instead of the concealed drawer fascia. The drawer box is fixed to the fascia with the drawer brackets. Follow the instructions supplied with the Easy Space and fit the drawer runners and packers for a 735 high Highline unit. The packers are fitted to the right side only. I Bottom Drawer- Except for the concealed drawer fascia, use the components supplied with the Easy Space kit. The door fascia needs to be drilled for the rails and the holes for the brackets started with a bradawl in the positions shown in the illustration. The brackets are offset on one side for the packers. Fit the brackets to the fascia and assemble the drawer box using the door fascia instead of the concealed drawer fascia. x insp iration for your home 3.5 x 7 x4

23 Section 8: Caring for your Kitchen Please note that although these units have been designed to give years of pleasure and satisfaction, you will help maintain the original beauty of your kitchen by following these guide lines. Timber Doors, Trims And Timber Accessories The wood products you have purchased will resist most household chemicals including alcohol. However, any spillage which occurs should be wiped off at once and the area should be rinsed thoroughly and wiped dry! On no account should any spillage, even water, be allowed to lie on the surface. Occasional marks can, in most cases, be removed with a soft damp cloth. More persistent marks can be removed using a mild solution of water and household detergent. Once the mark is removed, the area should be wiped over with a damp cloth to remove any excess water and dried with a soft, clean cloth. On no account should solvents or an abrasive cleaner be used as permanent damage to the finish could take place. A good quality wax furniture polish can be used occasionally to emphasise the inherent beauty of the timber. Please read the manufacturer's instructions first. Glass Doors A non-abrasive window cleaner should be used, if the door is leaded care should be taken using cleaning solutions on the decorative leading. Melamine, Vinyl And Foil Wrapped Mdf Doors Occasional marks can, in most cases, be removed with a soft damp cloth. More persistent marks can be removed using a mild solution of water and household detergent. Once the mark is removed, the area should be wiped over with a damp cloth to remove any excess and dried with a soft, clean cloth. On no account should solvents or an abrasive cleaner be used as permanent damage to the finish could take place High Gloss Doors Use a cleaning product not containing aggressive substances like acetone, alcohol, bleach as those components could seriously damage the surface of the door. The best would be to use soft cotton or micro fibre cloth with only water and soft soap (containing maximum % of liquid soap). Also smoking may cause discolouration on some finishes which is not removed by the recoended cleaning methods. Worktops All exposed worktop edges must be sealed with a waterproof sealant to prevent water moisture penetration, which will cause the laminate to lift. Although the worktop is very hard wearing, sharp knives and objects will scratch the surface. To prevent damage, a chopping board should be used and pots and pans should be lifted and not dragged. Care should be taken not to drop any heavy objects onto the worktop as the surface may crack. The laminate surface can tolerate boiling water and hot cooking splashes but may be damaged if very hot saucepans, oven dishes, electric irons or burning cigarettes are placed on the surface. To prevent damage always use heat resistant mats and ashtrays. For cleaning, a damp soapy cloth will clean off most spills. Bleaches, scouring pads, multi-surface cleaners should not be used. Concentrated juices, corrosive liquids and food colourants should be wiped off iediately. On no account should any spillage, even water, be allowed to lie on the surface. Carcases Do not use polish on any surfaces, a damp cloth with soapy water will clean off most marks and spills. On no account should any spillage, even water, be allowed to lie on the surface. Bleaches, scouring pads, multi-surface cleaners should not be used. Drawers, Runners, Doors And Hinges These should be wiped out with a damp soapy cloth and wiped dry with a soft cloth when necessary. The roller runners and hinges are lubricated and should not be cleaned with a degreasing agent as this will affect the action of the moving parts. Never lean on partially or fully open doors and drawers in order to gain access to base units. The hinges are specified to adequately support the weight of a door, plus small additional weights such as wire racks holding cloths, small jars of herbs etc. It is advised that once the kitchen has been installed you should check every six months that all screw 'B' on the hinges are tight. It is recoended not to attach a waste bin to the door, but instead use one supported by the carcase. Wall Units Care should be taken not to position kettles, or any appliance which creates a large amounts of heat or steam underneath a wall unit. Excessive heat or moisture can damage the units and doors. Temperature And Humidity Avoid excessive change in temperature and humidity as much as possible. Always try to ensure adequate ventilation when cooking and washing. Dryers, if possible, should be vented to the outside to avoid excessive humidity in the kitchen. 3

24 Section 9: Key Unit Dimensions 307 Wall Shelf Unit / 500 Glass unit 500 Cooker Hood 600 Aluminium Decorative Wall / 900 Feature Cabinet Tall Wall Cabinets 3,4,5 & & / 600 Up & Over Cabinet 800/000 Dresser unit /600 with Tambour 50 Wine Rack 600 / 900 /00 Aventos Feature Cabinet 500 Open display plate rack 900 Aventos with Glass Feature Door 600 BI-Fold Cabinet 600 Cooker hood 600 Integrated hood 600 Short Wall Unit Decor end panels Wall Dresser Dresser Unit Base Shelf Unit Decor moulding /500 Drawer pack 600 Belfast sink support unit /900 x Pan Drawers 600/ Pan Drawer 600 / 900 / Pullout 800/ Open display Open display wicker baskets wine rack 900 Belfast sink support unit Butler Sink 0/3 7 Décor shelf Butler sink support unit 3* 600 Single oven unit 600 Extractor Tray 900 Single oven unit 600 Double oven Tall Type AM Larder Unit Type CM Compact Oven Microwave Coffee Machine Type GM 450 Integrated Dishwasher Type EM Single oven Compact Oven / 500 Belfast Sink 600 Bowfront sink support unit B Also available with drawer Base Type B/J Double oven (drawers optional) Type D 600 Microwave Single oven Type E In column fridge or freezer Type F I n column fridge or freezer 3* 0* 3* 0* 0* wire baskets Bow Fronted Sink 50 Pullout Base Belfast Sink 50 Wine rack /500 Pull Out Option Larders 300/ /600 & 000 Larder Type A/H Single oven (drawers optional) Type C/K 450 Microwave Single oven (drawers optional) Type L 450 Appliance 450 Appliance Integrated Living Type F In column Fridge In column Freezer Range specific Forli Larder Type G In column fridge or freezer Tall Pilaster * 3* 0* 0* 0* Bridge Unit 600 Bridge Unit 400 Small Wall Unit 600 Short Wall Unit Larder Type A/H Type B/J Type C/K Type D Type E Type F Type G Type L Standard & Tall Wall Corner Cabinets Type BM In column fridge or freezer Type DM Compact Oven Microwave Coffee Machine Built-under Appliances: Dishwashers; Built-Under Refrigeration; Washing Machines Type EM Single oven Compact Oven 900 Single Pan Drawer 600 Single Pan Drawer Single Appliance Ref.7300 (5 ) Pair of Appliances Single Appliance Single Appliance Spacer panel Please Note: Every effort has been made to insure that this product leaves the factory in perfect condition. Any item which has a visible defect must not be installed and the customer service department contacted iediately 3/05/ Corner Wall Unit 65 L' Shape Corner Wall 600 Closed Wall Unit Base/Wall Quad Unit 65 Internal Curved Corner Wall This corner type is range specific The overall size requires 95 x Base Corner Cabinets Please note: Not all units are available in all ranges and style may vary. *3 and 0 filler may be required to be cut down to suit various appliances 95 L' Shape Corner Base 95 Syncromotion Corner Unit 95 Internal Curved Corner Base 95 Internal Curved Corner Base Range Specific Tall Corner Cabinets 900 Mondo Corner Unit This may require Decor End Panels Walk-In Corner Pantry 95 Tall Corner Carousel Tall Curved Larder