SANDVIK CH430 Installation Drawings

Transcription

1 Nanjing Manganese Manufacturing Co,:Ltd Tel: Website: SANDVIK CH430 Installation Drawings Nanjing Manganese Manufacturing Co.;Ltd, which had specialized in casting crusher wear parts,jaw crusher parts, cone crusher parts,impact crusher parts, vsi crusher parts,roll mill parts and other manganese,chrome casting parts over 20 years. Our foundry locates in Gangtang town,shuangfeng city,hunan province.

2 Appendix A: Installation drawings IM Sandvik CH430:01, :02 A-3

3 IM Sandvik CH430:01, :02 A.1 General The following drawings show machine dimensions, connection positions and dimensions, and access dimensions. All dimensions must be respected. Dimensions are given in millimeters with inch dimension in brackets. NOTE! A.1.1 The motor can be installed on either side of the crusher. Mechanical drawings Drawing name Drawing No. Note Installation Oil tank installation Oil connection (standard) Oil connection (USA) Air over-pressure (blower/compressed air) Foundation loads A.1.2 Electrical drawings Drawing name Drawing No. Note Piping and instrument diagram, typical installation Connection diagram, oil tank Circuit diagram Instrument list Sensor list Modification of return oil flow switch option Connection of extra heating elements option Connection of heating cable option Connection of heater for Hydroset oil option

4 IM Sandvik CH430:01, :02 A.1.3 Foundation loads Drawing No The values are applicable for the maximum eccentric throw (36 mm (1.42")). Forces on foundation at each attachment point. CH430:01, :02 fixed installation kn lbf Vertical static load including material* Dynamic load during normal operation f = 6.0 Hz: Rotating horizontal force (H) Cyclic vertical force (V) ± * Material volume =1.20 m 3 (40 ft 3 ) * Bulk density = kg/m 3 (3 970 lbs) CH430:01, :02 on rubber dampers kn lbf Vertical static load including material* Dynamic load during starting and stopping: Rotating horizontal force (H) Cyclic vertical force (V) ± Dynamic load during normal operation f = 6.0Hz Rotating horizontal force (H) Cyclic vertical force (V) ±3 675 Horizontal displacement: ± 15 mm in all directions during starting and stopping ± 5 mm in all directions during operation * Material volume = 1.20 m 3 (40 ft 3 ) * Bulk density = kg/m 3 (3 970 lbs) CH430:01, :02 with subframe on rubber dampers kn lbf Vertical static load including material* Dynamic load during starting and stopping: Rotating horizontal force (H) Cyclic vertical force (V) ± Dynamic load during normal operation f = 6.0 Hz Rotating horizontal force (H) Cyclic vertical force (V) ±3 675 Horizontal displacement: ± 15 mm in all directions during starting and stopping ± 5 mm in all directions during operation * Material volume = 1.20 m 3 (40 ft 3 ) * Bulk density = kg/m 3 (3 970 lbs)

5 IM Sandvik CH430:01, :02 A.1.4 Mechanical connections Drawing No (standard) Drawing No (USA) The drawings show the points on the crusher and tank unit where connections are made, and also show the hoses that are supplied. This overview shows general information about the connections for the cone crusher and its accessories. Tank unit Dimension Max pressure A Lubrication oil from crusher Rp 2" internal thread B Lubrication oil to crusher Rp 1½" internal thread C Hydroset Rp ¾" internal thread D To oil heat exchanger Rp 1" E From oil heat exchanger Rp 1" F, G Over-pressure air Rp ¾" internal thread Crusher H Over-pressure air Rp ¾" internal thread I Lubrication oil to tank R 2" K Lubrication oil from tank G 1½" B L Hydroset G ¾" B Water/oil heat exchanger (option) M Oil inlet G 1½" B N Water outlet G 1½" B O Water inlet Rp 1½" B P Oil outlet G 1½" B Air/oil heat exchanger Q Oil outlet G 1¼" R Oil inlet G 1¼"

6 IM Sandvik CH430:01, :02 Mechanical connections overview H F G E I K A B C D L M N R O P Q

7 IM Sandvik CH430:01, :02 A.1.5 NOTE! Cable overview This cable overview shows general information about electrical cables not included in the delivery from Sandvik. Site specific signal cables are excluded from this table. All cable types and dimensions must meet local legislation. Cable Object Cable path Rating Notes designation From To 50 Hz 60 Hz W1-M1 Crusher main motor Switchgear -M kw W1-M2 Lubrication oil pump Switchgear -L9 1.5 kw 1.7 kw W1-M3 Cooling fan Switchgear -M3 1.5 kw 1.7 kw Option W1-M8 Over-pressure fan Switchgear -M kw 0.43 kw Option W1-E7 Oil tank heating Switchgear -L kw depending on voltage and number of heaters W1-CV Power supply Switchgear -L9 - - W2-CV Signals from switches -L9 Control system or similar - -

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25 Plant: Equipment Tag No: Equipment Name: Equipment Supplier: INSTRUMENT LIST HYDROCONE CH/CS-420/430 SANDVIK ROCK PROCESSING IDENTIFICATION INSTRUMENT TYPE APPLICATION INSTRUMENT DETAILS REMARKS Plant SRP Model Range Part No. Manufacturer Tag No. Tag No. -TI1 Thermometer Return oil temperature (main) ICF ºC LTR Lubr. system -PI1 Pressure gauge Hydroset pressure 100M MPa Tempress Hydroset system -PI2 Pressure gauge Oil pressure (main) 2748 D MPa Wika Lubr. system -LI1 Oil level indicator Oil level in tank (main) H High/Low Parker Hannifin Lubr. system -LI2 Oil level indicator Oil level in tank (Hydroset) H High/Low Parker Hannifin Hydroset system

26 Plant: Equipment Tag No: Equipment Name: Equipment Supplier: HYDROCONE CH/CS-420/430 SANDVIK ROCK PROCESSING SENSOR LIST IDENTIFICATION SENSOR TYPE APPLICATION SENSOR DETAILS REMARKS Plant SRP Model Range Part No. Output Contact Manufacturer Tag No. Tag No. rating -TG1 Thermostat Return oil temperature RT NC/NO 4A,400V Danfoss Lubr. system -TG2 Thermostat Oil cooling RT NC/NO 4A,400V Danfoss TG3 Thermostat Oil heating RT NC/NO 4A,400V Danfoss OG1 Flow indicator Return oil flow HeliFloat PF NC/NO 6A,240V HeliSim PG2 Pressure guard Filter diff. pressure (main) PIS bar NO 2,5A 230V Knecht B1N Position sensor Mainshaft position (HS-2800) EDS mm mA Micro Epsilon ASRi -B1N Position sensor Mainshaft position (HS-3800) EDS mm mA Micro Epsilon ASRi -B2N Press. transmitter Hydroset pressure bar mA Tecsis ASRi -B3N Temp. transmitter Return oil temperature FLEXTOP PT C mA Bourdone Sed. ASRi -U1N Power transducer Drive motor power draw P mA Tillquist ASRi

27

28

29

30