anti-condensation valve

Transcription

1 anti-condensation valve

2 Dimensions B C B Function The ltecnic anti-condensation valve connects between a biomass burning boiler and a direct or indirect heating system or domestic hot water system. It automatically controls the return temperature to the boiler to avoid condensation, by means of an integral thermostatic sensor. Keeping the boiler at a high temperature prevents condensation forming from the water vapour contained in the flue gases. It can be used on central biomass boilers or residential biomass burners such as fireplace heating systems and solid fuel stoves and cookers The anti-condensation valve gives the boiler a longer life and ensures greater efficiency. Design ulti-functional Body The compact brass single body casting houses the thermostatic sensor and temperature gauge pockets enables immediate installation of the unit, either on the right or left of the biomass boiler, respecting the flow directions as shown. The brass body prevents the formation of ferrous residues in the system, thereby helping to prolong the life of the boiler. nti-condensation valve nti-condensation valve incorporates a thermostatic sensor to control the temperature of water returning to the boiler, preventing the formation of condensation. The sensor has been specifically designed to be removed from the valve body for maintenance, re-setting or replacement if necessary. Pockets for Temperature Gauges The body of the anti-condensation valve in sizes DN25 (1 ) and DN32 (1¼ ) have pockets for temperature gauges on the front and rear sides. The pockets allow the installation of suitable temperatures gauges for measuring the three water temperatures and re-setting the thermostat if required. Code DN B C D E F kg R¾ R R R1¼ Code 6 th Digit D E F Setting 45 C 55 C 60 C 70 C Technical Specification Component aterial Specification Body: DN20 Brass BS EN CW617N DN25 & DN32 Brass BS EN 1982 CB753S Cap: Brass BS EN CW614N Obturator: PSU Polymer Spring: Stainless steel Swing check valve: PPS Polymer Sealing elements: EPD Union sealing washers: Non-asbestos fibre Wax thermostatic sensor Performance edium: water glycol solution ax. glycol percentage: 50% ax. working pressure: 10 bar ax. operating temperature: 5 C to 100 C Connections Pipe connections: nti-condensation valve Setting temperature: Setting accuracy: Bypass complete closing temperature: male taper with union BS EN C, 55 C, 60 C & 70 C ±2 C + 10 C

3 Components The Wooden biomass and condensation build-up Flow bypass Wooden solid fuel contains a variable moisture percentage depending on the type (logs, pellets, woodchips etc.) and seasoning. Water vapour is released during the solid fuel drying phase inside the combustion chamber. 5 7 The presence of cold zones in the boiler or flue gas chimney can lower the temperature of the flue gas down to the dew point, causing condensation to occur. Return to boiler System return Water vapour condenses onto the boiler surfaces, together with soot and part of the unburnt hydrocarbons contained in the flue gas, producing deposits and tar. These substances stick to the walls of the boiler, covering most of the inner surfaces. In addition to being dangerous due to its flammability, tar is damaging to the integrity of the boiler and limits the efficiency of the flue gas-system water exchanger. 1 nti- condensation thermostatic sensor 2 Obturator 3 Spring 4 Cap 5 Valve body 6 Temperature gauge pocket Kv Values and Flowrates 4 8 By keeping the boiler walls at the highest possible temperature, the anti-condensation recirculation and unit limits the formation of these substances, thereby increasing the combustion efficiency, controlling the emissions into the environment and prolonging the life of the boiler. Flue gas and emission control SF DN20 DN25 DN32 50 pressure loss - kpa flowrate - l/m ccumulation of ash and residues Primary and secondary air: Combustion efficiency SR NTI-CONDENSTION VLVE Zone ofcondensation forming: Deposits and tar Corrosion Reduction inheat exchanger efficiency Flammability Size DN20 DN20 DN25 DN32 Connection ¾ 1 1 1¼ Kv m 3 /h

4 Operating Principle The thermostat (1), which is completely immersed in the medium, controls the obturator (2) that regulates the flow through the bypass port (7) and back towards boiler. s the boiler starts up from cold the anti-condensation valve re-circulates the water so that it brings the boiler up to temperature as quickly as possible. Operating Principle Continued > +10 C SYSTE LODING by-pass closed > > +10 C, = SYSTE STRTUPTRNSIENT system returnclosed, = = ixed water temperature returning to boiler = Return water temperature from storage cylinder = Flow temperature = nti-condensation set temperature When the flow temperature exceeds the set temperature of the anti-condensation valve, the units cold port (8) starts to open to produce mixed water, in this phase the system loading begins. > STRT OF SYSTE LODING >, <, = Schematic Symbols When the return temperature to the boiler is greater than the set temperature of the anti-condensation valve by 10 C, the bypass port (7) closes and water returns to the boiler at the same temperature as the water returning from the storage cylinder. > +10 C SYSTE LODING > > +10 C, = Deaerator Dirt separator Pump Shut-off valve Expansion vessel Check valve otorised mixing valve Pressure reducing valve Filling unit Backflow preventer Safety reliefvalve Dirt separator for vertical pipes Deaerator for vertical pipes Y-strainer

5 Typical pplications Biomass Boiler with Calorifier for Indirect Heating Biomass Boiler with Direct Heating and Calorifier E & O.E ltecnic Ltd ustang Drive, Stafford, Staffordshire ST16 1GW T: +44 (0) E: sales@altecnic.co.uk Registered in England No: altecnic.co.uk L