WALL MOUNTED TYPE ROOM AIR-CONDITIONER

Transcription

1 TECHNICAL MANUAL & PARTS LIST DRAFT WALL MOUNTED TYPE ROOM AIR-CONDITIONER (Split system, air to air heat pump type) SRK50HE-S, SRK56HE-S (Split system, air cooled cooling only type) SRK50CE-S, SRK56CE-S

2 INDOOR UNIT Models SRK50HE-S, SRK56HE-S SRK50CE-S, SRK56CE-S OUTDOOR UNIT Models SRC50HE-S, SRC56HE-S SRC50CE-S, SRC56CE-S REMOTE CONTROLLER

3 1 GENERAL INFORMATION 1.1 Specific features The Mitsubishi Daiya room air-conditioner: SRK series are of split and wall mounted type and the unit consists of indoor unit and outdoor unit with refrigerant precharged in factory. The indoor unit is composed of room air cooling or heating equipment with operation control switch and the outdoor unit is composed of condensing unit with compressor. (1) Remote control flap The flap can be automatically controlled by operating wireless remote controller. Air scroll: Flap operation is automatically control. Swing: This will swing the flap up and down. Memory flap: Once the flap position is set, the unit memorizes the position and continues to operate at the same position from the next time. (2) Automatic operation When the remote control switch is set on auto( ), it will either automatically decide operation mode such as cooling, heating and thermal dry, or operate in the operation mode before it has been turned to automatic control. () Self diagnosis function We are constantly trying to do better service to our customers by installing such judges that show abnormality of operation as follows. RUN light TIMER light Outdoor (LED) 1 time flash Heat exchanger sensor error 1 time flash OFF Outdoor temperature sensor error TIMER light ON 2 time flash Room temperature sensor error RUN light keeps flashing 2 time flash OFF Outdoor unit heat exchanger sensor error 6 time flash Indoor fan motor error 4 time flash OFF Discharge pipe sensor error 5 time flash 5 time flash Over heat of compressor RUN light ON 6 time flash 6 time flash Error of signal transmission 2 time flash OFF Abnormality of outdoor unit 1.2 How to read the model name Example : SR K 50 H E - S R410A models Series No. H: Heat pump type C: Cooling only type Product capacity Wall mounted type Split type room air-conditioner - 1 -

4 2 SELECTION DATA 2.1 Specifications Item Model SRK50HE-S Cooling capacity (1) W 4700 Heating capacity (1) W 500 Power source 1 Phase, V, 50Hz Cooling input kw 1.41 Running current (Cooling) A 6.5/6./6.0 Heating input kw 1.40 Running current (Heating) A 6.5/6.2/6.0 Inrush current A 9.6 Operation data (2) Model COP Cooling:. Heating:.79 SRC50HE-S Sound level Hi 4, Me 9, Lo 4 47 Cooling Power level 58 6 Noise level db Sound level Hi 44, Me 9, Lo 5 49 Heating Power level Exterior dimensions Height Width Depth mm Color Cool white Stucco white Net weight kg Refrigerant equipment Compressor type & Q ty RM-B5118MNE5 (Rotary type) 1 Motor kw 1.4 Starting method Line starting Heat exchanger Louver fins & inner grooved tubing Straight fins & inner grooved tubing Refrigerant control Capillary tubes + Electronic expansion valve Refrigerant () kg R410A 1.4 (Pre-Charged up to the piping length of 15m) Refrigerant oil R 0.7 (MA68) Deice control Microcompter control Air handling equipment Fan type & Q ty Tangential fan 1 Propeller fan 1 Motor W 27 5 Air flow (at High) (Cooling) CMM (Heating) Air filter, Q ty Polypropylene net (washable) 2 Shock & vibration absorber Cushion rubber (for compressor) Electric heater Operation control Operation switch Wireless-Remote controller Room temperature control Microcomputer thermostat Pilot lamp RUN (Green), TIMER (Yellow), HI POWER (Green), ECONO (Orange) Safety equipment Compressor: Overheat protection, Serial signal error protection, Indoor fan motor error protection, Frost protection Refrigerant piping O.D mm (in) Liquid line: φ6.5 (1/4 ) Gas line: φ12.7 (1/2 ) Connecting method Flare Connection Attached length of piping Liquid line: 0.54 m Gas line : 0.47 m Insulation Necessary (Both sides) Connectable 2 m ( cores with earth) Size Core number 1.5 mm 2 4 cores (Including earth cable) Connecting method Terminal block (Screw fixing type) Drain hose Power source cord Connection wiring SRK50HE-S (Indoor unit) SRC50HE-S (Outdoor unit) Accessories (included) Mounting kit, Clean filter (Natural enzyme filter 1, Photocatalytic washable deodorizing filter 1) Optional parts Notes (1) The data are measured at the following conditions. Item Indoor air temperature Outdoor air temperature Operation DB WB DB WB Standards Cooling 27ºC 19ºC 5ºC 24ºC ISO-T1, JIS C9612 Heating 20ºC 7ºC 6ºC ISO-T1, JIS C9612 The piping length is 7.5m. (2) The operation data are applied to the 220/20/240V districts respectively. () The refrigerant quantity to be charged includes the refrigerant in 15 m connecting piping. (Purging is not required even for the short piping.) If the piping length is longer, when it is 15 to 25 m, add 20 g refrigerant per meter

5 Model SRK56HE-S (Indoor unit) SRC56HE-S (Outdoor unit) Item Model SRK56HE-S Cooling capacity (1) W 5100 Heating capacity (1) W 5800 Power source 1 Phase, V, 50Hz Cooling input kw 1.59 Running current (Cooling) A 7./7.1/6.8 Heating input kw 1.58 Running current (Heating) A 7.4/7.1/6.8 Inrush current A 45.2 Operation data (2) COP Cooling:.21 Heating:.67 SRC56HE-S Sound level Hi 44, Me 40, Lo 5 49 Cooling Power level Noise level db Sound level Hi 44, Me 9, Lo 5 51 Heating Power level Exterior dimensions Height Width Depth mm Color Cool white Stucco white Net weight kg Refrigerant equipment Compressor type & Q ty RM-B5120MNE5 [Rotary type] 1 Motor kw 1.5 Starting method Line starting Heat exchanger Louver fins & inner grooved tubing Straight fins & inner grooved tubing Refrigerant control Capillary tubes + Electronic expansion valve Refrigerant () kg R410A 1.4 (Pre-Charged up to the piping length of 15m) Refrigerant oil R 0.7 (MA68) Deice control Microcomputer control Air handling equipment Fan type & Q ty Tangential fan 1 Propeller fan 1 Motor W 27 5 Air flow (at High) (Cooling) CMM (Heating) Air filter, Q ty Polypropylene net (washable) 2 Shock & vibration absorber Cushion rubber (for compressor) Electric heater Operation control Operation switch Wireless-Remote controller Room temperature control Microcomputer thermostat Pilot lamp RUN (Green), TIMER (Yellow), HI POWER (Green), ECONO (Orange) Safety equipment Compressor: Overheat protection, Serial signal error protection, Indoor fan motor error protection, Frost protection Refrigerant piping O.D mm (in) Liquid line: φ6.5 (1/4 ) Gas line: φ12.7 (1/2 ) Connecting method Flare connection Attached length of piping Liquid line: 0.54 m Gas line : 0.47 m Insulation Necessary (Both sides) Connectable 2 m ( cores with earth) Size Core number 1.5 mm 2 4 cores (Including earth cable) Connecting method Terminal block (Screw fixing type) Drain hose Power source cord Connection wiring Accessories (included) Mounting kit, Clean filter (Natural enzyme filter 1, Photocatalytic washable deodorizing filter 1) Optional parts Notes (1) The data are measured at the following conditions. Item Indoor air temperature Outdoor air temperature Operation DB WB DB WB Standards Cooling 27ºC 19ºC 5ºC 24ºC ISO-T1, JIS C9612 Heating 20ºC 7ºC 6ºC ISO-T1, JIS C9612 The piping length is 7.5m. (2) The operation data are applied to the 220/20/240V districts respectively. () The refrigerant quantity to be charged includes the refrigerant in 15 m connecting piping. (Purging is not required even for the short piping.) If the piping length is longer, when it is 15 to 25 m, add 20 g refrigerant per meter. - -

6 Model Model Item SRK50CE-S SRC50CE-S Cooling capacity (1) W 4700 Power source 1 Phase, V, 50Hz Cooling input kw 1.41 Running current (Cooling) A 6.5/6./6.0 Inrush current A 9.6 COP Cooling:. Noise level Sound level Hi 4, Me 9, Lo 4 47 Cooling db Power level 58 6 Exterior dimensions Height Width Depth mm Color Cool white Stucco white Net weight kg Refrigerant equipment Compressor type & Q ty RM-B5118MNE5 (Rotary type) 1 Motor kw 1.4 Starting method Line starting Heat exchanger Louver fins & inner grooved tubing Straight fins & inner grooved tubing Refrigerant control Capillary tubes + Electronic expansion valve Refrigerant () kg R410A 1.4 (Pre-Charged up to the piping length of 15m) Refrigerant oil R 0.7 (MA68) Deice control Microcomputer control Air handling equipment Fan type & Q ty Tangential fan 1 Propeller fan 1 Motor W 27 5 Air flow (at High) (Cooling) CMM Air filter, Q ty Polypropylene net (washable) 2 Shock & vibration absorber Cushion rubber (for compressor) Electric heater Operation control Operation switch Wireless-Remote controller Room temperature control Microcomputer thermostat Pilot lamp RUN (Green), TIMER (Yellow), HI POWER (Green), ECONO (Orange) Safety equipment Compressor: Overheat protection, Serial signal error protection, Indoor fan motor error protection, Frost protection Operation data (2) Refrigerant piping O.D mm (in) Liquid line: φ6.5 (1/4 ) Gas line: φ12.7 (1/2 ) Connecting method Flare connection Attached length of piping Liquid line: 0.54 m Gas line : 0.47 m Insulation Necessary (Both sides) Connectable 2 m ( cores with earth) Size Core number 1.5 mm 2 4 cores (Including earth cable) Connecting method Terminal block (Screw fixing type) Drain hose Power source cord Connection wiring SRK50CE-S (Indoor unit) SRC50CE-S (Outdoor unit) Accessories (included) Mounting kit, Clean filter (Natural enzyme filter 1, Photocatalytic washable deodorizing filter 1) Optional parts Notes (1) The data are measured at the following conditions. Item Indoor air temperature Outdoor air temperature Operation DB WB DB WB Standards Cooling 27ºC 19ºC 5ºC 24ºC ISO-T1, JIS C9612 The piping length is 7.5m. (2) The operation data are applied to the 220/20/240V districts respectively. () The refrigerant quantity to be charged includes the refrigerant in 15 m connecting piping. (Purging is not required even for the short piping.) If the piping length is longer, when it is 15 to 25 m, add 20 g refrigerant per meter

7 Model SRK56CE-S (Indoor unit) SRC56CE-S (Outdoor unit) Model Item SRK56CE-S SRC56CE-S Cooling capacity (1) W 5100 Power source 1 Phase, V, 50Hz Cooling input kw 1.59 Running current (Cooling) A 7./7.1/6.8 Inrush current A 45.2 COP Cooling:.21 Noise level Sound level Hi 44, Me 40, Lo 5 49 Cooling db Power level Exterior dimensions Height Width Depth mm Color Cool white Stucco white Net weight kg Refrigerant equipment Compressor type & Q ty RM-B5120MNE5 [Rotary type] 1 Motor kw 1.5 Starting method Line starting Heat exchanger Louver fins & inner grooved tubing Straight fins & inner grooved tubing Refrigerant control Capillary tubes + Electronic expansion valve Refrigerant () kg R410A 1.4 (Pre-Charged up to the piping length of 15m) Refrigerant oil R 0.7 (MA68) Deice control Microcomputer control Air handling equipment Fan type & Q ty Tangential fan 1 Propeller fan 1 Motor W 27 5 Air flow (at High) (Cooling) CMM Air filter, Q ty Polypropylene net (washable) 2 Shock & vibration absorber Cushion rubber (for compressor) Electric heater Operation control Operation switch Wireless-Remote controller Room temperature control Microcomputer thermostat Pilot lamp RUN (Green), TIMER (Yellow), HI POWER (Green), ECONO (Orange) Safety equipment Compressor: Overheat protection, Serial signal error protection, Indoor fan motor error protection, Frost protection Operation data (2) Refrigerant piping O.D mm (in) Liquid line: φ6.5 (1/4 ) Gas line: φ12.7 (1/2 ) Connecting method Flare connection Attached length of piping Liquid line: 0.54 m Gas line : 0.47 m Insulation Necessary (Both sides) Connectable 2 m ( cores with earth) Size Core number 1.5 mm 2 4 cores (Including earth cable) Connecting method Terminal block (Screw fixing type) Drain hose Power source cord Connection wiring Accessories (included) Mounting kit, Clean filter (Natural enzyme filter 1, Photocatalytic washable deodorizing filter 1) Optional parts Notes (1) The data are measured at the following conditions. Item Indoor air temperature Outdoor air temperature Operation DB WB DB WB Standards Cooling 27ºC 19ºC 5ºC 24ºC ISO-T1, JIS C9612 The piping length is 7.5m. (2) The operation data are applied to the 220/20/240V districts respectively. () The refrigerant quantity to be charged includes the refrigerant in 15 m connecting piping. (Purging is not required even for the short piping.) If the piping length is longer, when it is 15 to 25 m, add 20 g refrigerant per meter

8 2.2 Range of usage & limitations Item Indoor return air temperature (Upper, lower limits) Outdoor air temperature (Upper, lower limits) Refrigerant line (one way) length Vertical height difference between outdoor unit and indoor unit Models All models Refer to the selection chart Max. 25m Max. 15m (Outdoor unit is higher) Max. 15m (Outdoor unit is lower) Power source voltage Rating ± 10% Voltage at starting Frequency of ON-OFF cycle ON and OFF interval Min. 85% of rating Max. 10 times/h Max. minutes 2. Exterior dimensions (1) Indoor unit Models All models Unit: mm A Piping hole right 298 right: 67 left : Indoor unit 69 Installating board Drain hose 515 (ø16) Piping for gas 5.5 (ø12.7) Piping for liquid 60.5 (ø6.5) VIEW A Piping hole (ø65) Piping hole (ø65) - 6 -

9 (2) Outdoor unit Models All models Drain holes Elogated hole (2-12 x16) Terminal block Ground terminal Service valve (Liquid) ø6.5 (1/4'') Service valve (Gas) ø12.7 (1/2'')

10 2.4 Piping system Models SRK50HE-S, 56HE-S Indoor unit Flare connection Outdoor unit Service valve (Gas) Cooling cycle Heating cycle Outdoor air temp. sensor Piping (Gas) ø12.7 Check joint 4 way valve Accumulator Room temp. sensor Heat exchanger Heat exchanger sensor Discharge pipe temp. sensor Compressor Heat exchanger Heat exchanger sensor Piping (Liquid) ø6.5 Service valve (Liquid) Capillary tube Capillary tube Flare connection Strainer Electronic expansion valve Models SRK50CE-S, 56CE-S Indoor unit Flare connection Outdoor unit Service valve (Gas) Cooling cycle Outdoor air temp. sensor Piping (Gas) ø12.7 Check joint Accumulator Room temp. sensor Heat exchanger Heat exchanger sensor Discharge pipe temp. sensor Compressor Heat exchanger Heat exchanger sensor Piping (Liquid) ø6.5 Service valve (Liquid) Capillary tube Capillary tube Flare connection Strainer Electronic expansion valve - 8 -

11 2.5 Selection chart Correct the cooling and heating capacity in accordance with the conditions as follows. The net cooling and heating capacity can be obtained in the following way. Net capacity = Capacity shown on specification Correction factors as follows. (1) Coefficient of cooling and heating capacity in relation to temperatures 1. Coefficient of cooling & Heating capacity in relation to temperature Cooling Heating Applicable range Cooling operation Outdoor air D.B. temperature C D.B Indoor air W.B. temperature C W.B. ISO-T1 Standard Condition Heating operation Indoor air D.B. temperature C D.B Outdoor air W.B. temperature C W.B. ISO-T1 Standard Condition (2) Correction of cooling and heating capacity in relation to one way length of refrigerant piping It is necessary to correct the cooling and heating capacity in relation to the one way piping length between the indoor and outdoor units. Piping length [m] Cooling Heating () Correction relative to frosting on outdoor heat exchanger during heating In additions to the foregoing corrections (1), (2) the heating capacity needs to be adjusted also with respect to the frosting on the outdoor heat exchanger. Air inlet temperature of outdoor unit in C WB Adjustment coefficient How to obtain the cooling and heating capacity Example : The net cooling capacity of the model SRK50HE-S with the piping length of 15m, indoor wet-bulb temperature at 19.0 C and outdoor dry-bulb temperature 5 C is Net cooling capacity = = 458 W SRK50HE-S Length 15m Factor by air temperatures - 9 -

12 Power source 1 Phase V 50Hz BR LB Y/GN HEAT EXCHANGER FMI SM Y BL 52C4 52C N J G 52C CNU CNM F 250V.15A ( ) CNE ZNR Printed circuit board CNG 52C Indoor unit TB TB N N Outdoor unit Y/GN - Y/GN G1 ZNR + D.S F (250V.15A) J N L CM2 52X1 CM1 52X2 5 52X 1 CC U CM V CFO OR CNU 51C 20S W FMo Models SRK50HE-S, 56HE-S.1 Electrical wiring ELECTRICAL DATA Color symbol BR LB OR Y Y/GN Black Brown Red Light Blue Orange White Yellow Yellow/Green Display Wireless R-Amp Th1 Th2 52X1 52X2 52X RL Printed circuit board CNE CNG CNB EEV Th4 Th5 Th6 Meaning of marks Symbol Parts name CM Compressor motor F Fuse FMI Fan motor (Indoor) FMo Fan motor (Outdoor) SM Flap motor RL Inspection lamp Th1 Room temp. sensor Symbol Th2 Th4 Th5 Th6 ZNR 20S 52C Parts name Heat exchanger sensor (Indoor unit) Heat exchanger sensor (Outdoor unit) Outdoor air temp. sensor Discharge pipe sensor Varistor 4 way valve (coil) Magnetic contactor Symbol Parts name DS Diode stack 52X1- Auxiliary relay EEV Electronic expansion valve 51C Motor Protector for CM TB Terminal block

13 Power source 1 Phase V 50Hz BR LB Y/GN HEAT EXCHANGER FMI Y BL 52C4 52C N J G 52C CNU F 250V.15A ( ) ZNR 52C Printed circuit board Indoor unit 1 TB TB 1 2 N 2 N Outdoor unit Y/GN - Y/GN G1 ZNR + D.S J N L F (250V.15A) CM2 52X1 CM1 52X2 5 CC U V CM CFO OR CNU 51C W FMo Models SRK50CE-S, 56CE-S SM CNM CNE CNG 52X1 52X2 Color symbol BR LB OR Y Y/GN Black Brown Red Light Blue Orange White Yellow Yellow/Green Display Wireless R-Amp Th1 Th2 RL Printed circuit board CNE CNG Th4 Th5 Th6 EEV Meaning of marks Symbol Parts name CM Compressor motor F Fuse FMI Fan motor (Indoor) FMo Fan motor (Outdoor) SM Flap motor RL Inspection lamp Symbol Th1 Th2 Th4 Th5 Th6 ZNR Parts name Room temp. sensor Heat exchanger sensor (Indoor unit) Heat exchanger sensor (Outdoor unit) Outdoor air temp. sensor Discharge pipe sensor Varistor Symbol Parts name 52C Magnetic contactor DS Diode stack 52X1-2 Auxiliary relay EEV Electronic expansion valve 51C Motor Protector for CM TB Terminal block

14 4 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER 4.1 Operation control function by remote control switch Remote controller Models All models S Operation section FAN SPEED button Each time the button is pushed, the indicator is switched over in turn. OPERATION MODE select button Each time the button is pushed, the indicator is switched over in turn. HI POWER button This button changes the HIGH POWER mode. ON/OFF button Press for starting operation, press again for stopping. ECONO button AIR FLOW button This button changes the ECONOMY mode. This button changes the flap mode. When pressed, this button changes the mode in the following order: (Air scroll) (Flap stopped) (Swing) TEMPERATURE button This button sets the room temperature. (This button changes the present time and TIMER time.) ON TIMER button This button selects ON TIMER operation. CANCEL button This button cancels the ON timer and OFF timer. Time switch This switch for setting the time. OFF TIMER button This button selects OFF TIMER operation. The above illustration shows all controls, but in practice only the relevant parts are shown. RESERVE button This button sets the present time and TIMER time. RESET switch Switch for resetting microcomputer. S Indication section HIGH POWER MODE indicator Indicates during high power mode operation. TEMPERATURE indicator Indicates set temperature. (Does not indicate temperature when operation mode is on AUTO) FAN SPEED indicator AUTO HI MED LO HI POWER ON AM ECONO PM OFF ECONOMY MODE indicator Indicates during economy mode operation. OPERATION MODE indicator Indicates selected operation with lamp. Heat pump type: [ (Auto) (Cool) (Heat) (Dry)] Cooling only type: [ (Auto) (Cool) (Fan) (Dry)] Indicates set air flow rate with lamp. TIME indicator Indicates present time or timer setting time. AIR FLOW indicator Shows selected flap mode. OFF TIMER indicator Indicates OFF TIMER operation. ON TIMER indicator Indicates during ON TIMER operation

15 Unit indication section Models All models RUN (HOT KEEP) light (green) Illuminates during operation. Brinks at air flow stop due to the HOT KEEP. TIMER light (yellow) Illuminates during TIMER operation. HI POWER light (green) Illuminates during HIGH POWER operation. ECONOMY light (orange) Illuminates during ECONOMY operation

16 5 INSTALLATION R410A refrigerant is used for this air-conditioner. Execute the installation work while taking care of the following points in addition to the general caution items. 5.1 Installation tools Prepare the following special tools for R410A in addition to the general-purpose tools. Flare tool Vacuum pump adaptor Gauge manifold Leak detector Charge hose 5.2 Refrigerant piping Use the copper pipe that has less than 40 mg/10 m of oil adhesion and 0.8 mm of wall thickness. Never use the thin walled pipe the thickness of which is less than 0.8 mm. Use the flare nut attached to the air-conditioner. 5. Pipe connection (1) Pipe working Copper pipe dia. Liquid side ø6.5 ø9.52 Gas side ø12.7 Dimension "A" (mm) Flare tool bar Dimension "B" Copper pipe Copper pipe dia. ø6.5 ø9.52 ø12.7 Dimension "B" (mm) Clutch type flare tool for R410A 0.0 ~ ~ ~ 0.5 (2) Tightening torque The tightening torque is shown below. Copper pipe dia. Liquid side ø6.5 ø9.52 Gas side ø12.7 Across flats of flare nut (mm) Tightening torque N m (kgf m) 14 ~ 18 (1.4 ~ 1.8) ~ 42 (. ~ 4.2) 50 ~ 62 (5.0 ~ 6.2) () Vacuuming The charge hose for R22 cannot be connected because the service port diameter is different from the conventional one. Use the special charge hose for R410A. Use the vacuum pump adapter for reverse flow prevention to check the reverse flow of vacuum pump oil. If oil flows back to the air-conditioner, it causes failure of refrigerant cycle. Service valve (Two-way) -101kPa (-76cmHg) Compound pressure gauge Handle Lo Service valve (-way) Charge Hose Service Port (Special for R410A) Pressure gauge Handle Hi Gauge manifold (Special for R410A) Charge hose (Special for R410A) Vacuum pump adaptor (For reverse flow prevention) (Special for R410A) Vacuum Pump

17 PARTS LIST (Main parts) (1) Indoor unit No. Parts Name SRK50HE-S Parts No. SRK56HE-S 1 PANEL ASSY, FRONT RKT102A750 2 PANEL, FRONT RKT122A600B GRILLE ASSY, AIR INLET RKT45A600B 4 GRILLE ASSY, AIR OUTLET RKT45A750 5 MOTOR, DC SSA512T046B 6 IMPELLER SSA41G040C 7 HEAT EXCH ASSY(AIR) RKT01A750 8 PWB ASSY RKV505A200G RKV505A200J 9 CONTROL ASSY, REMOTE RMA502A001 (2) Outdoor unit No. Parts Name SRC50HE-S Parts No. SRC56HE-S PANEL, FRONT PANEL, SIDE(R) PANEL, SIDE(L) PANEL, TOP GRILLE, AIR OUTLET GUA, FIN BRACKET, MOTOR MOTOR, AC PROPELLER BASE ASSY HEAT EXCH ASSY(AIR) VALVE, S(4WAY) COIL, SOLENOID RWC122A00 RWC12A005F RWC12A002 RWC124A00 RWC45A002 RWC11A004 RWC116A041 SSA511C06A SSA41B2 RWC111A00H RWC01A02 SSA82C078 RSA82F010B 14 COMPRESSOR ASSY AHT201A50ND AHT201A540ND PWB ASSY VALVE, BODY(EXP) COIL,SOLENOID RCP505A500C SSA87F05 SSA82F210A

18 PARTS LIST (Main parts) (1) Indoor unit No. Parts Name SRK50CE-S Parts No. SRK56CE-S 1 PANEL ASSY, FRONT RKT102A750 2 PANEL, FRONT RKT122A600B GRILLE ASSY, AIR INLET RKT45A600B 4 GRILLE ASSY, AIR OUTLET RKT45A750 5 MOTOR, DC SSA512T046B 6 IMPELLER SSA41G040C 7 HEAT EXCH ASSY(AIR) RKT01A750 8 PWB ASSY RKV505A200H RKV505A200K 9 CONTROL ASSY, REMOTE RMA502A001 (2) Outdoor unit No. Parts Name SRC50CE-S Parts No. SRC56CE-S PANEL, FRONT PANEL, SIDE(R) PANEL, SIDE(L) PANEL, TOP GRILLE, AIR OUTLET GUA, FIN BRACKET, MOTOR MOTOR, AC PROPELLER BASE ASSY HEAT EXCH ASSY(AIR) RWC122A00 RWC12A005F RWC12A002 RWC124A00 RWC45A002 RWC11A004 RWC116A041 SSA511C06A SSA41B2 RWC111A00H RWC01A02A 12 COMPRESSOR ASSY AHT201A50ND AHT201A540ND PWB ASSY VALVE, BODY(EXP) COIL, SOLENOID RCP505A500C SSA87F05 SSA82F210A

19 WALL MOUNTED TYPE ROOM AIR-CONDITIONER Air-Conditioning & Refrigeration Systems Headquarters 16-5, 2-chome, Kounan, Minato-ku, Tokyo, , Japan Fax : (0)