Installation lnstruc.tions Home Laundry Automatic Washers

Transcription

1 Installation lnstruc.tions Home Laundry Automatic Washers KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the washer changes ownership, be sure this manual accompanies the washer.) Part No R2 November 1997

2 1. Table of Contents. _ Replticetient Parts,.,. ->., -< _...*...*...*...*...*...*...*.*...*...*.*...~... 2 Roughing In Dimensions...**...*C*...*...**...*.*..*.~~...~..*...*. 3 Before You Start Tools..*..*...***..*.,...*...~...*.*...*.*..*.~..**.*...*...*..*.~*..~.*~~.**.*~.~~.* I ; Electrical.*.*,...~*.~..~.~*...*..~..*..*.*..*..*...*.*...**...~...*.*...*...~...**.*...**.*.*.. Water...~..~...~...~...~..~..~...~..~...~...~.~..~...~~...~~... 3., ^ - Installing the Washer Step 1 (Remove the Shipping Brace &d Shipping Plug) I Step 2 (Wipe Out Inside of -W&her)...~...~...~...~...~..~...~...~..~...~. 4 Step 3 (Connect Water Inlet Hoses) **...*..**.*...*...**...*..*.. 5 Steb 4 (Connect Drain Hose t.o Draie Receptacle)..*..C..*.*...***.*...*..* 6 Standpipe Itistallation...t...*...*.*.~*...*.*...*...*...~*...*... 6 I. High Standpipe Installation *...*..*.*...*...*.*...**. 7 Low St.atidpipe Installation.C...~~...~...C.~...~...~...~~..~... 7 Sink Inst&iation..*~...**...L...~.*...*...*..*..*...*..*...*..**.*..**.~**..*. 8 :I; the War1 Installation.C...~... 8 _ Laundry Tub Installation..*...*..*...*...*.*...*...~*.*...*...*...*.*. 8 Step 5 (Position and Level the Washer)...C...9 Step 6 (Plug in the Washer)...r~.-~..*..*...*..*...*...*...~.*..*...*...*. I 9 Step 7 (Add Water to the Washer).*...*...* Step 8 (Check Lid Switch) I...*...*...*.**...*...*...* Step 9 (Check Installation)...*...*..*...*..*...*...* Elect.rical Requirements...*..*...*...*..*...*..~..~.*...**...**.*...~...* 11 Water Supply Requirements Water Temperature..*...*..*...*.*.*...~..*...*.**...*...*...*...* 12 Water Pressure..*..*...*...*...*...*..*...*...*...*...*...*. 12 Rise.rs...*...~...*...*.~..*...*...~.*...*...**.*...*.*..*...*...**... 17I Installer Check..*...*.**.*...*...*...*...*...*..*.*...*. Back Cover Replacement Parts p If replacement parts are required, contact the source from Amana Appliances where you purc.hased your washer, or contact: P.O. Box 8901 Amana, IA Phone: (800) In U.S.A. (319) Outside U.S.A. FAX: (319) fur the name and address of the nearest authorized Amana parts distributor

3 : I Roughing In Dimensions E *WITH LEVELING LEGS TURNED INTO BASE Before You Start R For most installations, the basic tools vou will need are: J SCREWDRIVER 7. WRENCH : : I I i PLIERS fgiq I-/ y-4 w,, JJ 1, b-4 i>+?,i./ [.+t;i :!/ pi i j I ri 11 : _I- II t ii ii I),a ~~~:~j, f i ~ I I II, ;.I I, \,i i, I i :. \ (i Electrical Refer to Serial Plate for specific electrical requirements. For more detailed information refer to Section on Electrical Requirements. Water Washer needs two standard 3/4 inch (19.05 mm) water supply faucets with a pressure between pounds per square inch (138 to 827 kpa). For more detailed information refer to Section on Water Supply Requirements. LEVEL ~--~ vltp% -..p-; ;l, ~. -3 &!j,,q+- _.~.yy------!.i, 1 b---,,-. I..I D374lE 1 D

4 Installing the. Washer Step 1: Remove the Shipping Brace and Shipping Plug NOTE: Install drver before washer. This allows room for attaching exhkst duct. Remove the shipping; brace from under the lid. The plastic shipping plugwill be released from the base of the washer when removing the cardboard base from the washer. SH B NOTE: Do not tilt washer to front or sides when moving. The shipping brace and plug should be saved and must be reinstalled whenever washer is moved or transported to a new location. This will prevent damage to washer components. NOTE: See your Use and Care Guide for instructions on reinstallcng shipping brace and shipping plug. SHIPPING PLUG W373lEOA Step 2: Wipe Out Inside of Washtub Prior to first wash, use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub. W371 I EOA 38774

5 Step 3: Connect Water Inlet IHoses I I FILTER WASHER (Screen must be facing outward) XOTE: Refer t.o Section on Water Szqq~ly Requirements before connecting water inlet hoses. Remove the two screene.d filter washers and the two plain rubber washers from accessories bag: and install them according to the illustration. Turn on the water supplv faucets and flush the lines for approximately two minites to remove any foreign materials that could clog the filter screens in the inlet hoses, or the screens in the water mixing valve. NOTE: M7hen installing in newly construct.ed or renovated building, it is verv important to flush the lines since build-up may ha;e occurred during construction. IMPORTAANT: Thread hose couplings onto valve connections finger-tight, then approximat.ely l/4 turn wit.h pliers. DO NOT cross thread or overtighten couplings. Turn water on and check for leaks. If leaks are found, retighten the hose couplings. Continue tightening and rechecking until no leaks are found. I END OF HOSE TO WATER SUPPLY FAUCET RUBBER WASHER (Plain) \ INSTALL THIi END OF HOSE TO VALVE CONNECTIONS AT REAR OF WASHER W004lE1 C (continued) 5

6 Step 4: Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose. from the retainer clamp. Find the instructions, on the following pages, that are appropriate for your type of drain receptacle (standpipe, high standpipe, low standpipe, sink, wall, or laundry tubj. Follow these instructions to properly install the drain hose. IMPORTANT: Drain receptacle must. be capable of handling a minimum of l-1/4 inch (32 cm) outside diameter drain hose. RETAINER CLAMP STANDPIPE ADAPTER I W324lEOA Standpipe Installation: Place the adapter into the standpipe. Remove the beaded tie-down strap from accessories bag and place around standpipe and drain hose, approximately 12 inches (30 cm) down from the top of pipe and tighten strap to hold hose to standpipe. This will prevent the drain hose from dislodging from drain receptacle during use. IMPORTANT: To prevent siphoning, do not place anv ribbed portion of the drain hose into the stkdpipe. RlBBED PORTION OF DRAIN HOSE \ STANDPIPE ADAPTER / STANDPIPE TIE-DOWN 2 (5.08 cm) STRAP or 1 -f/2 (4 cm) W325lEl A 38774

7 High Standpipe Installation: Place the adapter into the standpipe. Remove the beaded tie-down strap from accessories bag and place around standpipe and drain hose, approximately 12 inches (30 cm) down from the top of pipe and tighten strap to hold hose to standpipe. This will prevent the drain hose from dislodging from drain receptacle during use. STANDPIPE ADAPTER U STANDPIPE (Standpipes higher than 4 feet [I22 cm] are not recommended) W327lEl A Low Standpipe Installation: No. 562P3 Siphon Break Kit is required for this tape of installation. This kit is available (as optional equiiment at extra cost) through an authorized dealer or parts distributor. Installation instructions are supplied with the. kit. 562P3 SIPHON (continued) 7

8 Sink Installation: For this type of installation, use the beaded tie-down strap (supplied in accessories bag), or use a large wire tie (available from your local hardware store) and secure the drain hose to the cabinet top hinge. See illustration. This will prevent the drain hose from dislodging during use. We recommend leaving the standpipe adapter on the drain hose for this tvpe installation. d DRAlN HOSE TlE-DOWN STRAP OR WIRE TIE / CAMNiT TOP HINGE WI 77lEl A In the M7all Installation: For installations of this type, the drain hose MUST be secured to one of the inlet hoses using the beaded tiedown strap from accessories bag. TIE-DOWN STRAP NOTE: End of drain hose must not be below height of cabinet. top. Laundrv Tub Installation: For this hype of installation. I the drain hose IMUST be secured to the stationary tub to prevent hose from dislodging during use. Use the beaded tie-down strap (supplied in accessories bag) to secure hose. We recomme.nd leaving the standpipe adapter on the drain hose for this type installation. W78!ElA 38774

9 Step 5: Position and Level the Washer Place rubber feet on all four leveling legs. Place washer in position on a clean, dry, and reasonably firm floor. Installing the washer on any type of carpeting is not recommended. LEVEL Loosen 7/8 locknuts and adjust the two front leveling legs. Once adjusted, tilt the unit forward on front legs and lower back down into position to set the rear self-leveling legs. Washer must not rock. After washer is at desired height, tighten locknuts securely against bottom of washer base. If these locknuts are not tight, washer will not remain stationary during operation. Improper installation or flexing of a weak floor will cause excessive vibration. Jk LEVELING LEG Do not slide washer across floor once the leveling legs have been extended, as legs and base could become damaged. Step 6: Plug in the Washer Refer to Section on Electrical Requirements, and plug the washer in. D254lEOA (continued) 9

10 Step 7: Add Water to the Washer To prevent damage to pump, do not run washer before adding at least on; quart water to the tub. If the washer is run before any water is added, the pump seal may overheat causing the pump to leak. Once installed, the water retained in the drain system from the previous cycle will provide sufficient cooling to prevent pump seal damage. NOTE: The agitator should not be removed except for service. The washtub is designed to be self-cleaning. W391 IElA J Step 8: Check Lid Switch Washer should stop agitating and spinning when lid is opened. Step 9: Check Installation Refer to Installer Check on the back cover of this manual and make sure that washer is installed correctly,

11 Electrical Requirements w (120 Volt, 60 Hertz with 3-Prong Grounding Plug) NOTE: The wiring diagram is located in the control hood..a WARNING To reduce the risk of fire, electric shock or personal injury, all wiring and earthing MUST conform with the latest edition of the National Electrical Code, ANSVNFPA 70, and such local regulations as might apply. It is the customer s responsibility to have the wiring, fuses and circuit breakers checked by a qualified electrician to make sure your home has adequate electrical power to operate the washer. WI29 Grounding Instructions The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric curtent. The washer is equipped with a cord having an equipment-grounding conductor and a 3-prong grounding plug. The plug must be plugged into an appropriate outlet. that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug; provided with the washer - if it will not fit the outlet, Kave a proper outlet installed by a qualified electrician. a WARNING improper connection of the equipmentearthing conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the washer is properly grounded. W032 DO NOT OVERLOAD CIRCUITS DO NOT USE ADAPTER DO NOT USE AN EXTENSION CORD D009lEl A NOTE: Have a qualified electrician check the polarity of the \F7a11 receptacle. If a voltage reading is measureb other than that illustrated, the qualified electrician should correct the problem. STANDARD 120 VOLT, 60 HERTZ, 31WIRE EFFECTIVELY GROUNDED CIRCUIT NEUTRAL NEUTRAL \ D090tEl A I1

12 WARNH+dG Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an oben flame during this time. WO29 NOTE: Water supple faucets must. fit standard 314 inch (19.05 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS. NOTE: Water supply faucets should be readilv accessible to permit turning them off when washer is not being used. WATER COLD WATER CONNECTION \ Water Temperature Cold: Recommended cold water temperature is 50@ to 75 Fahrenheit, 10c to 24 Celsius. Hot: Recommended hot water temperature. is 1403 to 150 Fahrenheit, 60 to 66* Celsius. Warm: Mixture of hot and cold water. (Warm water temperature is dependent upon the water tempe.rature and the pressure of both the hot and cold water supply lines.) IMPORTANT: Turn off water supplv faucets after check-out and demonstration. Ownerw should turn off water supply whenever there will be an extended period of non-use. NOTE: Longer inlet hoses are available (as optional equipment. at extra cost) if the hoses (supplied with the washer) are not long enough for the installation. Order hoses as follows: No Inlet Hose (8 foot) (2.44m) No Inlet Hose (10 foot) (3.05m)I Water Pressure Pressure must be a minimum of 20 to a maximum of 120 pounds per square inch (138 to 827 kpa) static pressure measured at the faucet. NOTE: Water pressure under 20 pounds per square inch (138 kpa) will cause an extended fill time in the washer. WATER 1NiET HOSES / HOT WATER CONNECTION W187lElA Risers Risers (or air cushions) may have to be installed if the pipes knock or pound when flow of water stops. The risers are more efficient when installed as close as possible to the water supply faucets. See illustration below. RISERS (Air cushions) W0051E1 C

13

14

15 38774

16 Installer heck p Fast Track for Installing the Washer- (Refer to the manual for more detailed information) Position and Level the 0 -LEVEL 0 D2551EOA 0 CHECK /./;a\ I ti?--, Y, b ; \,/ W373tEOC cj W3161EOA Washtub. 0 0 I Plug in the Washer. 0 CHECK W371 IEOB n CHECK v I Connect Water Inlet JV314lEOl3 W39l IEOA II Connect Drain Hose to Drain Receptacle. Check Lid CHECK I I I!I L- Ll W3! 51EOA / W376lEOB 38774