ACUIX. Installation Manual. Indoor and Outdoor Housings. Document Rev B 03/08

Transcription

1 ACUIX Indoor and Outdoor Housings Installation Manual Document Rev B

2 Revisions Issue Date Revisions A 02/08 New document based on rev1.01, with new interface board. B Corrected safety cable call-out line on Figure 1-2, page 16.

3 FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to part 15 of the FCC rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference. For example, try orienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, or connecting the equipment to an outlet on a different circuit. Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Users of the product are responsible for checking and complying with all federal, state, and local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell Video Systems shall not be held responsible for the use of this product in violation of current laws and statutes. Canadian Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Manufacturer s Declaration of Conformance The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN for emissions, EN for immunity, and EN for Electrical Equipment safety. Document Rev B 3

4 Explanation of Graphical Objects The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the enclosure of the product that may be of sufficient magnitude to constitute a risk of electric shock to the person. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompany the product. Important Safety Instructions READ INSTRUCTIONS - All safety and operating instructions should be read before the unit is operated. 1. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference. 2. HEED WARNINGS - All warnings on the unit and in the operating instructions should be adhered to. 3. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed. 4. CLEANING - Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may result in the risk of fire, electric shock, or injury to persons. 6. ACCESSORIES - Only use accessories specified by the manufacturer. Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult and serious damage to the equipment. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. Wall or shelf mounting should follow the manufacturer's instructions and should use a mounting kit approved by the manufacturer. 7. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 8. POWER SOURCES - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or local power company. 9. OVERLOADING - Do not overload outlets and extension cords as this can result in a risk of fire or electric shock. 10. POWER-CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords, plugs, and convenience receptacles. 11. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 4

5 12. DAMAGE REQUIRING SERVICE - Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or moisture. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or the enclosure has been damaged. f. When the unit exhibits a distinct change in performance - this indicates a need for service. 13. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 14. SAFETY CHECK - Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 15. LIGHTNING AND POWER LINE SURGES - For added protection of this unit when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the unit due to lightning and power-line surges. 16. HEAT - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 17. INSTALLATION - Install in accordance with the manufacturer s instructions. Do not install the unit in an extremely hot or humid location, or in a place subject to dust or mechanical vibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit. Prior to installation and use of this product, please observe the following cautions and warnings. Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Document Rev B 5

6 Warning WARNING! Installation and servicing must be performed by qualified personnel in accordance with current IEE wiring regulations. WARNING! The PSU must be wired to a double pole fuse spur with 3mm separation. The 3A fuse spur must be located close to the PSU. WARNING! Using replacement parts or accessories other than the original manufacturers may invalidate the warranty. WARNING! To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance with the installation instructions. 6

7 ACUIX Housing Installation Manual Contents 1 Installing the Housing Introduction Related Documents Models Housings Lower Domes In-Ceiling (dropped) Housing Installation In-Ceiling Housing Installation Indoor Pendant Housing Installation Outdoor Pendant Housing Installation Wiring Recommended Cabling Connections Power Control Data RS485 Wiring RS485 Termination Control over Coaxial Cable Video Unshielded Twisted Pair (UTP)/Coaxial Selection Video Over Coaxial Cable Alarms Rev B 7 Document

8 Contents Rev B 8 Document

9 ACUIX Housing Installation Manual Figures Figure 1-1 Dropped Ceiling Housing Installation Figure 1-2 In-Ceiling Hole Dimensions Figure 1-3 In-Ceiling Housing Installation Figure 1-4 Spacing Wing Tabs Figure 1-5 Pendant Dome Housing Installation Figure 1-6 Outdoor Pendant Housing Installation Figure 2-1 Routing Field Wiring and Location of Terminal Blocks Figure 2-2 Terminal Block Wiring Figure 2-3 RS485 Termination SW1 Location Figure 2-4 RS485 Home Run Wiring (One Dome per Control Output) Figure 2-5 RS485 Daisy-Chain Wiring (up to 32 domes) with Control at One End Figure 2-6 UTP/Coaxial Selection on Interface Board Figure 2-7 Alarm Connection Rev B 9 Document

10 Figures Rev B 10 Document

11 ACUIX Housing Installation Manual Tables Table 1-1 ACUIX Housing Model Numbers Table 1-2 Lower Dome Model Numbers Table 2-1 ACUIX Recommended Cabling Table 2-2 ACUIX Wiring Table 2-3 Maximum Distance to Dome Table 2-4 Power Supplies Rev B 11 Document

12 Tables Rev B 12 Document

13 ACUIX Housing Installation Manual 1 Installing the Housing Introduction The ACUIX product line offers housings for indoor and outdoor applications. The indoor application features a pendant housing for wall mounting. The outdoor application features a pendant housing with a sunshroud and heater and blower. The outdoor pendant housing can be mounted on a pendant mount, wall mount, or parapet mount. There are also adapters available for corner and pole mounting. This chapter provides instructions for mounting the different types of housings. Each housing contains an interface board that provides wiring for video on coax or unshielded twisted pair, and control data on shielded or unshielded twisted pair (RS485) or over coax. Refer to your specific mount manual for installing the mount. Refer to the ACUIX User Manual for installing the pan and tilt camera assembly and lower dome and for operation and programming information. Related Documents For more information about topics that are relevant to the subject of this manual, see the documents listed below: Document title Part number ACUIX User Manual ACUIX Quick Set-Up Poster HDPRM2 Parapet Mount Install Guide HDXWM1 Decorative Wall Mount Install Guide HDCM1 Indoor Pendant Mount Install Guide Document Rev B 13

14 Installing the Housing Models Housings Refer to the following table for the housing model numbers. Table 1-1 ACUIX Housing Model Numbers Housing Model Number HDH00DA00 HDH00PA00 HDH00BA00 HDH00WA00 Description Indoor In-ceiling Indoor Pendant, White Indoor Pendant, Black Outdoor Pendant Lower Domes The following table lists the lower domes available for the housings. Refer to the ACUIX User Manual for installing the lower dome. Table 1-2 Lower Dome HDB00P0SW HDB00P0SB HDB00P0CW HDB00P0CB HDB00D0CW HDB00D0SW HDB00D0CB HDB00D0SB HDB00D0GW HDB00D0GB Lower Dome Model Numbers Description Pendant, Smoke Lower Dome, White Trim Ring Pendant, Smoke Lower Dome, Black Trim Ring Pendant, Clear Lower Dome, White Trim Ring Pendant, Clear Lower Dome, Black Trim Ring Pendant, Clear Lower Dome, White Trim Ring Pendant, Smoke Lower Dome, White Trim Ring Pendant, Clear Dome, Black Trim Ring Pendant, Smoke Dome, Black Trim Ring Pendant, Gold Dome, White Trim Ring Pendant, Gold Dome, Black Trim Ring 14

15 ACUIX Housing Installation Manual In-Ceiling (dropped) Housing Installation WARNING! Installation must be performed by qualified technical personnel and must be in accordance with all national and local mechanical and electric codes. Perform the following steps to install a dropped ceiling housing (see Figure 1-1): Figure 1-1 Dropped Ceiling Housing Installation Field wiring access hole Dropped Ceiling Plate Lower dome mounting posts (3 places) Attach lanyard to lower dome Drywall ceiling 1. Select the location of the housing. Each ACUIX requires a 24 VAC ± 10% power source when measured at the dome. Ensure a A power source is available. See Chapter 2, Wiring, Table 2-3 on page 25 for maximum wiring distances to the dome. 2. Remove the ceiling panel at the dome location. 3. Place the ceiling tile on the dropped ceiling plate. Trim the ceiling tile so you can press the ceiling tile into the dropped ceiling plate. 4. Cut a hole in the ceiling tile flush with the hole in the center of the plate. 5. If necessary, secure a safety cable (supplied by the installer) to a building support structure. Honeywell recommends using a 3/32 plastic coated aircraft cable. 6. Insert the housing in the ceiling a. Adjust the turning screws on the wing tabs to ensure the space between the wing tabs and housing flange is greater than the thickness of the ceiling. b. Position the wing tabs flat against the housing. Insert the housing through the hole in the ceiling. Using a Phillips screwdriver, turn the two screws in the housing clockwise to rotate the tabs out and tighten the tabs against the ceiling. The recommended maximum torque is N-m or lbf-ft or lbf-in. c. Insert the housing through the hole in the ceiling, ensuring the wing tabs are flat against the housing. The recommended maximum torque is N m Document Rev B 15

16 Installing the Housing 7. Refer to Wiring on page 21 for information on connecting the field wiring to the interface board in the housing. 8. Refer to the ACUIX User Manual to install the camera assembly and the lower dome. In-Ceiling Housing Installation WARNING! Installation must be performed by qualified technical personnel and must be in accordance with all national and local mechanical and electrical codes. Perform the following steps to install an ACUIX in-ceiling housing: 1. Select the location(s) of the housing(s). Each ACUIX requires a 24 VAC ± 10% power source when measured at the dome. Ensure a A power source is available. See Chapter 2, Wiring, Table 2-3 on page 25 for maximum wiring distances to the dome. 2. Cut a 7 5/8 (193.8 mm) diameter hole in the ceiling. Figure 1-2 In-Ceiling Hole Dimensions 7 5/8" (193.8 mm) Attach safety cable from building support structure to one of the lugs that secures the wing tab screw to the housing. 3. If the ceiling is drywall or plaster, Honeywell Video Systems recommends sealing the entire perimeter of the ceiling cut-out with tape or plastic channel (provided by the installer). This prevents dust and material from dropping from the ceiling. 16

17 ACUIX Housing Installation Manual 4. If required, secure a safety cable (supplied by the installer) to a building support structure. Honeywell recommends using a 3/32 plastic coated aircraft cable. Attach the safety cable (from the building support structure) to the housing by: a. Threading the safety cable through a looping sleeve, b. Around one of the lugs that secures the wing screws to the housing (refer to Figure 1-2), c. Back through the looping sleeve, and then d. Crimp the looping sleeve to secure the safety cable. 5. Insert the housing in the ceiling. Attach to building structure Looping sleeves (2) Attach to lug on wing bracket on housing Figure 1-3 In-Ceiling Housing Installation Cable entry hole a. Make sure the space between the wing tabs on the housing and the housing flange is greater than the thickness of the ceiling. Adjustments are made by turning the screws on the wing tabs; clockwise decreases the space between the tab and the housing flange and counterclockwise increases the space between the tab and the housing flange. Make sure the wing tabs on the housing are staggered so the tabs are not at the same height. Figure 1-4 Spacing Wing Tabs b. Position the wing tabs flat against the housing. Insert the housing through the hole in the ceiling (some jostling is required). Using a Phillips screwdriver, turn the two screws in the housing clockwise to rotate the tabs out and tighten the tabs against the ceiling. The recommended maximum torque is N-m (Newton meters) or lbf-ft (pound-force-foot) or lbf-in (pound-force-inch). Document Rev B 17

18 Installing the Housing 6. Refer to Wiring on page 21 for information on connecting the field wiring to the interface board in the housing. 7. Refer to the ACUIX User Manual to install the camera assembly and the lower dome. Indoor Pendant Housing Installation WARNING! Installation must be performed by qualified technical personnel and must be in accordance with all national and local mechanical and electrical codes. Perform the following steps to install an ACUIX pendant housing on a Honeywell Video Systems indoor wall or ceiling dome mount. See Figure Select the location(s) of the housing(s). Each ACUIX requires a 24 VAC ± 10% power source measured at the housing. Ensure a A power source is available. See Chapter 2, Wiring, Table 2-3 on page 25 for maximum wiring distances to the dome. 2. Install the mount using the instructions provided with your specific mount. 3. Run the field wiring (control data, video, power, and alarm) through the mount. The wiring must extend at least one foot (0.3 m) past the pipe for wiring purposes. See Wiring on page 21 for detailed wiring information. 4. Locate the pendant housing. Figure 1-5 Pendant Dome Housing Installation 1.5" NPT threaded nipple Route field wiring from mount 18

19 ACUIX Housing Installation Manual a. Insert the field wiring (data, power, video, and alarm) from the mount through the threaded nipple on the pendant housing. b. Carefully thread the housing into the mount. 5. See Connections on page 22 for information on connecting the field wiring to the terminal strips on the interface board in the housing. 6. Refer to the ACUIX User Manual to install the camera assembly and the lower dome. Outdoor Pendant Housing Installation WARNING! Installation must be performed by qualified technical personnel and must be in accordance with all national and local mechanical and electrical codes. Perform the following steps to install an ACUIX outdoor dome on a Honeywell Video Systems outdoor mount: 1. Select the location(s) of the housing(s). Each ACUIX requires a 24 VAC ± 10% power source measured at the housing. Ensure a A power source is available. See Chapter 2, Wiring, Table 2-3 on page 25 for maximum wiring distances to the dome. 2. Install the mount using the instructions provided with your specific mount. Run the required field wiring through the mount for the ACUIX dome. The wiring must extend at least one foot (0.3 m) past the pipe for wiring purposes. See Wiring on page 21 for detailed wiring information. 3. Locate the 1-1/2 NPT conduit nut shipped loose with the mount. Wrap Teflon tape (installer supplied) around the threaded nipple on the outdoor pendant housing. 4. Carefully thread the conduit nut onto the threaded nipple on the outdoor housing until the connection is as tight as possible. Document Rev B 19

20 Installing the Housing Figure 1-6 Outdoor Pendant Housing Installation 1.5 NPT threaded nipple wrap with teflon tape Route field wiring from mount 5. After the housing is threaded into the mount as far as it will go, thread the conduit nut on the housing up against the mount and tighten it. 6. See Connections on page 22 for information on connecting the field wiring to the interface board in the housing. Caution All joints, bolts, and screws in the mount must be properly sealed to prevent water (moisture) from entering the housing. 7. Refer to the ACUIX User Manual to install the camera assembly and the lower dome. 20

21 ACUIX Housing Installation Manual 2 Wiring This chapter provides the recommended cable types, cable distances for proper operation of the ACUIX dome, and wiring connections in the housing. All field wiring is connected to the interface board installed inside the housing. Where applicable, Category 5 (CAT5) cables or higher should be used. Recommended Cabling Table 2-1 ACUIX Recommended Cabling Type Recommended Cable Part Number Maximum Distance Video Coax, RG59/U, 75 Ohms BNC Connector, Crimp On for RG59/U BNC Connector, Screw Type for RG59/U feet (305 m) Data Power One Shielded Twisted Pair, RS485 Cable 18 AWG 2-Conductor, Vinyl Jacket feet (1219 m) See Gauge chart for each unit Alarm Belden ,000 feet Unshielded Twisted Pair (UTP) UTP Cabling: 1 twisted pair for data 1 twisted pair for video feet 1200 feet (365.7 m) Document Rev B 21

22 Wiring Connections Caution Installation must be performed by qualified technical personnel and must be in accordance with all national and local mechanical and electrical codes. The field wiring is connected to the interface board in the top of the ACUIX housing. 1. Route the field wiring (data, power, video, alarm) through the ACUIX mount, through the field wiring access hole in the housing and then through the access hole in the interface board installed in the housing. Figure 2-1 Routing Field Wiring and Location of Terminal Blocks Housing Field wiring access hole in housing Interface board J4 terminal blocks Field wiring access hole in interface board J1 terminal block J6 terminal block 2. Remove the plug-in terminal blocks on terminal strips J1 and J6. You should only remove the plug-in terminal block on terminal strip J4 if you are using alarm inputs. 22

23 ACUIX Housing Installation Manual Figure 2-2 Terminal Block Wiring Remove terminal blocks on J1, and J6. U3 SW2 ACUIX Interface Board (installed in housing) J3 Only remove terminal blocks on J4 when using alarm inputs. A1 CM A2 A3 CM A4 J4 1 J7 V+ V- Field wiring wire access hole J1 AC GND AC Fan D+ D- J6 SH SW1 3. Loosen the screws on the terminal strip. 4. Install the 24 VAC power wires, data wires, video wires (if UTP is selected) and alarm wires on the correct positions on terminal strips J1, J4, J6, and J7. Caution To make good wire contact and ensure it does not short to adjacent wires, fully insert the wire in the hole on the terminal strip. Document Rev B 23

24 Wiring Note You can connect the data cable shield to Pin 6 (SH) on terminal strip J1. Use this connection for looping the shield through to the next dome in the daisy chain. It is not connected to the analog interface board. Both terminal strips J1 and J6 accept AWG wire. If larger or smaller field-run wire is required, a AWG wire must be spliced onto the field wire for insertion into the terminal strip. Table 2-2 ACUIX Wiring Terminal Strip J1 Pin 1 Pin 2 Pin 3 Terminal Strip J6 Pin 1 Pin 2 Pin 3 Terminal Strip J4 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Terminal Strip J7 Pin 1 Pin 2 Function 24 VAC (AC) Earth Ground 24 VAC (AC) Function Data + (D+) Data (D ) Shield (SH) Function Alarm 1 (A1) Alarm Common (CM) Alarm 2 (A2) Alarm 3 (A3) Alarm Common (CM) Alarm 4 (A4) Video + (V+) (UTP wiring) Video (V ) (UTP wiring) Caution A good earth ground must be connected at J1, pin 2. Surge suppression is not provided if the unit is not connected to a good earth ground. 5. Tighten the screw on the terminal strip to secure the wire. 6. Plug the terminal strips into their respective connectors on the interface board. Caution Ensure there are no bare wires touching or faulty operation may occur. 24

25 ACUIX Housing Installation Manual 7. If you are using a coaxial cable for video, connect the field-run coaxial cable to J3 on the interface board. Note When connecting field wiring, connect to either J3 or J7, not to both at the same time. 8. Secure the wires from the terminal strip and BNC connector (if applicable) together with a wire tire to ensure the cabling does not interfere with the rotation of the pan and tilt assembly. 9. Feed extra wire and cable up through the hole in the top of the housing and route it so that it doesn't interfere with the pan and tilt unit when it is inserted. Caution Ensure the cabling does not interfere with the rotation of the pan and tilt assembly when it is installed. Power The indoor ACUIX requires a 24 VAC power 1.9A, measured at the dome. The outdoor ACUIX requires a 24 VAC power 2.5A, measured at the dome. The following table shows the wire gauge required for maximum distances to maintain 24 VAC ± 10% at the dome. These wire sizes and distances represent one power source for one ACUIX. Table 2-3 Maximum Distance to Dome AWG 24 VAC Camera Only (1.9A) 24 VAC Camera plus Heater & Blower (2.5A) feet (11.8 meters) 30 feet (9.1 meters) feet (18.9 meters) 47 feet (14.3 meters) feet (30.2 meters) 75 feet (22.9 meters) feet (47.9 meters) 120 feet (36.6 meters) feet (76.2 meters) 190 feet (58 meters) feet (100.0 meters) 302 feet (92 meters) Document Rev B 25

26 Wiring Caution Installation must be performed by a qualified electrician. The proper wire size for the distance and the number of domes must be determined to maintain 24 VAC at each ACUIX. Do not use the above table for this type of configuration. For CE compliance, the ACUIX power supply must be connected to a CE approved 240V UPS (uninterruptible power supply). One of the following power supplies must be used to meet FCC and UL requirements. Table 2-4 Power Supplies Model Number Description HPTV2416CB 16 Output, 24 VAC, 8 A, SmartFused HPTV2408CB 8 Output, 24 VAC, 4 A, SmartFused HPTV2404CB 4 Output, 24 VAC, 4 A, SmartFused HPTV2401WPZ Single Output, video, data and power protection, NEMA 4 Enclosure HPTV2401Z Single Output, video, data and power protection, Indoor Enclosure HPTVWPPMK2 2" Pole mounting kit for HPTV2401WPZ HPTVWPPMK3 3" Pole mounting kit for HPTV2401WPZ HPTVWPPMK4 4" Pole mounting kit for HPTV2401WPZ Control Data RS485 Wiring One pair of shielded twisted pair RS485 wire or one pair of unshielded twisted pair wire can be used for RS485 data. The data lines can be home-run wired or daisy-chain wired from the control output. Home-run wiring consists of one ACUIX per control output. The ACUIX must be terminated. Daisy-chain wiring consists of up to 32 domes per data run with the control output at one end of the run or in the middle of the run. If the control output is at the end of the data run, the last ACUIX on the end of the data run must be terminated and all intermediate dome s unterminated. If the control output is in the middle of the data run, the last ACUIX on both ends must be terminated, and all intermediate domes unterminated. 26

27 ACUIX Housing Installation Manual RS485 Termination RS485 communication is terminated using switch SW1 on the interface board installed in the ACUIX housing. SW1 is located near terminal strip J1, Pin 3. Figure 2-3 RS485 Termination SW1 Location J1 1 ACUIX Interface Board (installed in housing) J6 C4 T1 CR5 R3 SW1 shown in ON position SW1 RS485 termination: Switch positioned away from ON= not terminated (default) Switch positioned ON = terminated in 120 Ohms Figure 2-4 RS485 Home Run Wiring (One Dome per Control Output) SW1 Control equipment Dome terminated Document Rev B 27

28 Wiring Figure 2-5 RS485 Daisy-Chain Wiring (up to 32 domes) with Control at One End SW1 SW1 SW1 Up to 32 Control equipment Dome 1 unterminated Dome 2 unterminated Last Dome terminated Caution The data cable shield should be carried through all units by connecting the cable shields together. Connect the cable shield at the control unit. Control over Coaxial Cable The control equipment adds the data signal to the video coaxial cable. In this case, there are no connections made at Data+ and Data on the terminal strip J1. Caution For control over coaxial cable, the ACUIX must be set to VCL Video Telemetry (control over coax) protocol. The ACUIX must be controlled using an HMAX082 or HMAX162 control unit with HKJMMTP joystick controller. 28

29 ACUIX Housing Installation Manual Video Unshielded Twisted Pair (UTP)/Coaxial Selection Video over Unshielded Twisted Pair (UTP) is selected at switch SW2 on the interface board installed in the housing. Switch SW2 is located above terminal strip J4, pin 1. Figure 2-6 UTP/Coaxial Selection on Interface Board SW2 shown ON (with UTP enabled) U3 ACUIX Interface Board (installed in housing) BNC connector J4 R12 R13 Switch positioned away from ON: UTP video balun disabled, to be used with normal 75 Ohm coax video operation (default configuration). Switch positioned toward ON: UTP video balun enabled, to be used with 120 Ohm UTP video operation. Video Over Coaxial Cable The video must be terminated in 75 Ohms at the last video device. If the video is not terminated or is double terminated, the resulting picture is poor and ghosting is displayed. Document Rev B 29

30 Wiring Video Over Unshielded Twisted Pair (UTP) If the UTP option is selected, the video is run on UTP wire and the BNC connector is not used. The video is connected at terminal strip J7, pins 1 and 2. A UTP-compatible receiver is required at the monitor to view and/or record the images. Caution The video on the UTP wire cannot be daisy-chained. The video lift and gain settings can be adjusted through the on-screen setup menus to compensate for cable distances over UTP wiring. Refer to the ACUIX User Manual, On-Screen Setup Menus, Enhanced Settings. Alarms Connect a twisted-pair cable from each peripheral alarm contact to each input at the alarm number terminal and the alarm common terminal on terminal strip J4. The alarm is a dry contact between the alarm terminal and the common terminal. The alarms can be configured as normally open or normally closed. Note that the common terminals are doubled up, as shown in Figure 2-7. Refer to the ACUIX User Manual, On-Screen Setup Menus, Control Options, Program Alarms for configuring the alarms. Figure 2-7 Alarm Connection ALRM 1 ALRM 2 ALRM 3 ALRM 4 J4 A1 CM A2 A3 CM A4 30

31

32 Honeywell Video Systems (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA Honeywell Security Australia Pty Ltd. Unit 5, Riverside Centre, River Road West Parramatta, NSW 2150, Australia Honeywell Security Asia Pacific 33/F Tower A, City Center, 100 Zun Yi Road Shanghai , China Honeywell Security Asia Flat A, 16/F, CDW Building, 388 Castle Peak Road Tsuen Wan, N.T., Hong Kong Honeywell Security France Parc Gutenberg, 8, Voie La Cardon 91120, Palaiseau, France Honeywell Security Italia SpA Via della Resistenza 53/ Buccinasco Milan, Italy Honeywell Security España Mijancas 1. 3 a Planta P.Ind. Las Mercedes Madrid, Spain Honeywell Video Systems Northern Europe Netwerk WV Purmerend, The Netherlands Honeywell Systems Group Aston Fields Road, Whitehouse Ind Est Runcorn, Cheshire, WA7 3DL, UK (0) Honeywell Security South Africa Unit 6 Galaxy Park, 17 Galaxy Avenue Linbro Park, P.O. Box Kengray, Johannesburg, South Africa Honeywell Security Deutschland Johannes-Mauthe-Straße 14 D Albstadt, Germany Honeywell Security Poland Chmielewskiego 22a, Szczecin, Polska Honeywell Security Czech Republic Havránkova 33, Brno Dolní Heršpice, , Czech Republic Honeywell Security Slovakia Republic Vajnorská 142, Bratislava Slovakia CCTV (North America only) HVSsupport@honeywell.com Document Rev B 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.