Requirements of EN 1838: illuminance of 5 lx for safety equipment

Transcription

1 GuideLed SL 151, 152 CG-S Ceiling recessing, ceiling surface-mounting for illuminance of 5 lx vertically Requirements of EN 1838: illuminance of 5 lx for safety equipment Te aim of emergency ligting is to enable people to exit a room or building safely. It must also ensure tat fire figting and safety equipment can be easily found and operated wen needed. Tis equipment includes (but not exclusively): First aid stations All fire figting equipment and all alarm devices Ligting is required near eac first aid kit, near eac alarm and piece of fire figting equipment, as well as eac sign indicating a fire alarm system. In accordance wit EN 1838, near generally means a distance of no greater tan 2 metres, measured orizontally (tis corresponds wit Distance a in te diagram below). Te required level of illuminance on te equipment is 5 lx measured vertically - i.e. perpendicular to te usual orizontal illuminance measurements on one level. In comparison to te escape route requirement for 1 lx orizontally, different requirements apply in tis situation for te ligt distribution from te safety luminaires, due to te flatter ligt angle of incidence. GuideLed SL 151 und 152 CG-S meet te specific requirements of EN 1838 In order to meet te requirements of EN 1838, te new GuideLed SL 151 and 152 CG-S ave special optics to guarantee te required illuminance of 5 lx vertically over a wide area. Hence mounting at eigts of up to 5.6 m, and a breadt of illumination of up to 2.8 metres, are possible. Engineering elp, GuideLed SL 151 and 152 CG-S a m m Area in wic a minimum illuminance of 5 lx (maintenance factor 0.8) is acieved, depending on distance a and te rated operating time: a = 1,0 m a = 1,5 m a = 2,0 m 1.2 EMERGENCY LIGHTING Catalogue 103

2 GuideLed SL 151, 152 CG-S Ceiling recessing, ceiling surface-mounting for illuminance of 5 lx vertically GuideLed SL 151 CG-S * GuideLed SL 151, 152 CG-S Safety luminaire in LED tecnology for recessed mounting Unobtrusive design troug optics integrated in te luminaire Special asymmetric optics for illumination of 5 lx vertically for first aid stations, fire figting equipment and safety equipment acc. to EN 1838 Suitable for mounting eigts up to 5.6 m above te illuminated equipment Te illuminated area as a widt of up to 2.8 m. Minimum service requirement due to ig service life of te LEDs (50,000 ours) GuideLed SL 152 CG-S Luminous flux Φ N 310 lm Luminous flux Φ E /Φ N 100% at end of rated operating time Housing material Polycarbonate, aluminium Housing colour Wite, similar to RAL 9010 Weigt 0.3 kg Type of mounting Ceiling recessing, ceiling surface-mounting Terminals 2 x 3 x 2.5 mm² Connection voltage V AC, 50/60 Hz V DC Current consumption - battery operation (220 V) 21.5 ma Power consumption mains operation 8.5 VA / 5.0 W (apparent power/effective power) Permissible ambient temperature -20 C bis +0 C Ligt source HigPower LEDs 2 x 1.6 W C 0 C l/cd/klm Ordering details Scope of supply GuideLed SL 151 CG-S, recessed mounting wit asymmetric optics for illuminance of 5 lx vertically, incl. LED supply and CG-S Tecnology (20 addresses) GuideLed SL 152 CG-S, surface mounting wit asymmetric optics for illuminance of 5 lx vertically, incl. LED supply and CG-S Tecnology (20 addresses) Order No Ligt distribution curve GuideLed SL 151, 152 CG-S GuideLed SL 151 CG-S ,5 100 Orientation of escape route Ceiling cutout Tickness of ceiling 1-20 mm Module ousing GuideLed SL 152 CG-S , Orientation of escape route * GuideLed SL 151 CG-S: Degree of protection of te luminaire: IP1 Degree of protection of te module enclosure: IP EMERGENCY LIGHTING Catalogue

3 GuideLed SL 131, 132 CGLine Ceiling recessing, ceiling surface-mounting for illuminance of 5 lx vertically Requirements of EN 1838: illuminance of 5 lx for safety equipment Te aim of emergency ligting is to enable people to exit a room or building safely. It must also ensure tat fire figting and safety equipment can be easily found and operated wen needed. Tis equipment includes (but not exclusively): First aid stations All fire figting equipment and all alarm devices Ligting is required near eac first aid kit, near eac alarm and piece of fire figting equipment, as well as eac sign indicating a fire alarm system. In accordance wit EN 1838, near generally means a distance of no greater tan 2 metres, measured orizontally (tis corresponds wit Distance a in te diagram below). Te required level of illuminance on te equipment is 5 lx measured vertically - i.e. perpendicular to te usual orizontal illuminance measurements on one level. In comparison to te escape route requirement for 1 lx orizontally, different requirements apply in tis situation for te ligt distribution from te safety luminaires, due to te flatter ligt angle of incidence. GuideLed SL 131 and 132 CGLine meet te specific requirements of EN 1838 In order to meet te requirements of EN 1838, te new GuideLed SL 131 and 132 CGLine ave special optics to guarantee te required illuminance of 5 lx vertically over a wide area. Hence mounting at eigts of up to 5.6 m, and a breadt of illumination of up to 2.8 metres, are possible. Engineering elp, GuideLed SL 131 and 132 CGLine Rated operating time 1 Rated operating time 3 Rated operating time 8 a m m -2 m m -2 m m Area in wic a minimum illuminance of 5 lx (maintenance factor 0.8) is acieved, depending on distance a and te rated operating time: a = 1,0 m a = 1,5 m a = 2,0 m EMERGENCY LIGHTING

4 GuideLed SL 131 CGLine * GuideLed SL 131, 132 CGLine LED self-contained safety luminaire wit automatic test for reduced inspection effort Universal use for maintained and non-maintained operation and for 1, 3 or 8 operation For autonomous installation or connection to te CGLine monitoring system Environmentally-friendly due to modern litium ion tecnology Low operating costs via low connected load Minimum maintenance effort via ig LED service life (50,000 ours) Special asymmetric optics for illumination of 5 lx vertically for first aid stations, fire figting equipment and safety equipment acc. to EN 1838 Simple fault analysis and status display via bicolor LED and testing button 1 minute switc-back delay after mains return Blocking function prevents unintended discarge during idle operating times (only wit CGLine monitoring systems) GuideLed SL 132 CGLine C 0 C Ligt distribution curve GuideLed SL 131, 132 CGLine l/cd/klm Luminous flux Φ N (mains operation) 310 lm Luminous flux Φ E /Φ N 100 % at 1 ; 55 % at 3 ; 20 % at 8 at end of rated operating time Housing material Polycarbonate, aluminium Housing colour Wite, similar to RAL 9010 Weigt 0.62 kg (131 CGLine) 0.86 kg (132 CGLine) Type of mounting Ceiling recessing, ceiling surface-mounting Terminals Troug-wiring from mains (L, L`, N, PE) to 2.5 mm² CGLine Bus troug wiring to 1.5 mm² Connection voltage V AC, 50 Hz Power consumption mains operation 6.9 VA / 6.7 W (apparent power/effective power) Permissible ambient temperature Maintained mode -5 C bis + C Non-maintained mode 0 C bis +35 C Battery Litium-Ion 3.7 V/000 ma wit multiple protective circuit Ligt source HigPower LEDs 2 x 1.6 W Ordering details Scope of supply GuideLed SL /D CGLine, ceiling recessed wit asymmetric optics for illuminance of 5 lx vertically, clamping range for ceiling tickness 0-20 mm GuideLed SL /D CGLine, ceiling surface-mounted wit asymmetric optics for illuminance of 5 lx vertically Order No GuideLed SL 131 CGLine Alignment escape route Ceiling cut-out Ceiling tickness 1-20mm Required eigt in cavity ceiling for recessing troug ceiling cut-out: 150 mm GuideLed SL 132 CGLine * GuideLed SL 131 CGLine: Degree of protection of te luminaire: IP1,2 Degree of protection of te module enclosure: IP EMERGENCY LIGHTING

5 .1 Outdoor emergency ligting Atlantic LED Innovative LED tecnology Complies wit EN Rugged cast aluminum IK10 Ni-M HT Suitable for industrial environments Ligt Source: Two ig-brigtness LEDs of 1.6W wit loop life of ours Materials: Cast aluminum ousing unit in grey Wite polycarbonate reflector Clear polycarbonate diffuser AtlanticLED is a device for ligting and signaling safety. Te durable cast aluminum body along wit te ig IP65 protection rating, makes tis unit particularly suited to industrial areas, underground car parks and tunnels. Te electronic circuit performs self-diagnosis functions and independent tests for functionality and autonomy duration. AtlanticLED as internal jumpers tat allows to switc between 200 lux or 75 lux ligt output. Te optical asymmetric lens are optimally designed to spread ligt in corridors and escape routes. 62mm 3mm Operation: Maintained and Non- Maintained versions and CBS models available Autonomy 1 Manual test wit magnet Atlantic LED 136mm Installation: Wall and ceiling installations Applications: Factories, wareouses, underground car parks, worksops, tunnel Escape routes, corridors Atlantic LED can be used as exit sign Model Heigt (m) Distance for 1 Lux (open area) Distance for 0,5 Lux (escape route) Atlantic LED 03,00 03,00 07,90 07,50 16,70 15,00 06,60 03,50 02, 08,02 08, 18,60 16,60 07,0 0,00 0,00 08,0 09,10 20,0 18,00 08,10 Order code Description ATLANTIC LED R-AD, (open area) 2 x 1 6W LED 200Lm 60,8V-2,2A Maintained / Non-Maintained ATLANTIC LED R-AD, (escape route, double side) 2 x 1 6W LED 200Lm 60,8V-2,2A Maintained / Non-Maintained ATLANTIC LED R-AD, (escape route, single side) 2 x 1 6W LED 200Lm 60,8V-2,2A Maintained / Non-Maintained Accessories Single side pictogram (rigt) Single side pictogram (left) Single side pictogram (down) Double side pictogram (rigt) Double side pictogram (left) Double side pictogram (down) 68 Emergency ligting design andbook revision d_el_rev._eng July 201

6 Outdoor emergency ligting.2 Outdoor Wall Innovative LED tecnology Complies wit EN Rugged cast aluminum IK10 Ni-M HT Suitable for emergency exits Ligt Source: Two ig-brigtness LEDs of 1.6W wit loop life of ours Materials: Cast aluminum ousing unit in grey Wite polycarbonate reflector Clear polycarbonate diffuser Te durable cast aluminum along wit te ig degree of protection (IP65) makes tis outdoor wall unit particularly suitable for industrial areas, underground car parks and tunnels. Outdoor Wall as been developed to be mounted on te wall above te safety exits of a building bot inside and outside, tanks to te special design wic allows 90 installation and ensures te uniform illumination level required by law. Outdoor Wall as an internal jumpers tat allows to switc between 200 lux or 75 lux ligt output. Te optical asymmetric lens are optimally designed to spread ligt in corridors and escape routes. 3mm 18mm Operation: Maintained and Non- Maintained versions and CBS models available Autonomy 1 152mm 72mm 160mm Manual test wit magnet Installation: Outdoor wall Wall mounting over exits and escape routes versions Applications: 750 Factories, wareouses, underground car parks, worksops, tunnel Escape routes, corridors Installation on emergency exits inside and outside buildings Outdoor LED ligt coverage 2,5 m 5 lx 7,5 m 1 lx 12 m Order code Description OUTDOOR WALL AD 2 x 1 6W LED 200Lm 60,8V-2,2A Maintained / Non-Maintained Emergency ligting design andbook revision d_el_rev._eng July

7 Emergency Alfalux Hig Bay LED Designing emergency ligting for areas wit ig ceilings poses problems. Conventional bulkeads lack sufficient ligt output and often ave inappropriate potometric distribution. Twin spot projectors are equally unlikely to provide te 0.5 Lux minimum coverage over te entire core area for open areas as required for compliance wit standards. Alfalux ig bay provides a compact, simple to install solution suitable for mounting eigts up to 25m. Te Alfalux LED range is split into two variants wit a mid bay solution for low to medium eigt mounting and a Hig Bay solution up to 25m. 60,000 our LED options Mid bay and ig bay options for optimum luminaire efficiency reducing te number of fittings required Weaterproof IP65 ingress protection suitable for outdoor and wet environments Vandal resistant die-cast ousing wit polycarbonate lens Hinged gear tray for ease of installation Self-contained, slave, self-test and addressable testing options 262

8 Emergency Alfalux Hig Bay LED Lamp Options 13W ig power wite LED Materials Base - die-cast aluminium, finised in wite powder coated paint Diffuser - clear polycarbonate Battery - NiCd (self-contained version) Installation Notes Suitable for ceiling mounting Designed for mounting eigts of 6-25m Twin BESA entry drill-outs on rear 20mm conduit entry on eac end, wit blanking plugs for ease of installation Direct screw fix option, wit fixing oles outside IP65 area for improved ingress protection Geartray inged, retained in closed position by single tumb screw Terminal block, accommodating pus-in wiring (solid or stranded cables) Diffuser retained by allen key security screws Potometric Data Escape route 2m wide Open (anti-panic) area 1 lux min 0.5 lux min Mode Mounting Lux level eigt directly (m) under Mtd/NMtd Hig Bay V Slave & CEAG Hig Bay Mtd/NMtd Mid Bay V Slave & CEAG Mid Bay Self Contained W T5 NMtd Self Contained W T5 Mtd Options Self-contained - Can be operated in maintained or non-maintained mode Intellem self-test (see page 21) EasiCeck addressable test versions (see page 236) Central battery slave versions CEAG slave versions Specification To specify state: Self-contained - Hig output ig performance IP65 rated self-contained luminaire complete wit NiCd battery, control gear and purpose designed optic/reflector suitable for mounting eigts of up to 25 metres. Cast aluminium base and eavy duty clear diffuser as Alfalux Hig Bay LED part number Slave - Hig output ig performance IP65 rated slave luminaire complete wit ig output control gear and purpose designed optic/reflector suitable for mounting eigts of up to 25 metres. Cast aluminium base and eavy duty clear diffuser as Alfalux Hig Bay LED part number Catalogue Numbers System Mode Cat No Weigt (kg) LED Maintained 3Hr (Hi Bay) HLLEDH3H 2.7 LED Maintained 3Hr Intellem self-test (Hi Bay) HLLEDH3HIS 2.7 LED Maintained 3Hr EasiCeck 2 (Hi Bay) HLLEDH3HEC2 2.7 LED 2V AC Mains slave (Hi Bay) HLLEDH2 2.7 LED 2V Mains slave EasiCeck (Hi Bay) HLLEDH2EC 2.7 LED 2V CEAG slave (Hi Bay) HLLEDH2CG 2.7 LED Maintained 3Hr (Mid Bay) HLLEDL3H 2.7 LED Maintained 3Hr Intellem self-test (Mid Bay) HLLEDL3HIS 2.7 LED Maintained 3Hr EasiCeck 2 (Mid Bay) HLLEDL3HEC2 2.7 LED 2V AC Mains slave (Mid Bay) HLLEDL2 2.5 LED 2V Mains slave EasiCeck (Mid Bay) HLLEDL2EC 2.5 LED 2V CEAG slave (Mid Bay) HLLEDL2CG 2.5 Dimensions L (mm) W (mm) D (mm)