April 2, 2019 ADDENDUM NO. 3 DEPARTMENT OF PUBLIC WORKS OPERATIONS BUILDING

Transcription

1 April 2, 2019 ADDENDUM NO. 3 DEPARTMENT OF PUBLIC WORKS OPERATIONS BUILDING Notice is hereby given that the following additional information and changes shall become part of the specifications of the above referenced contract. You are to acknowledge the addenda on the Proposal Sheet. 1. SECTION DOOR HARDWARE Specifications attached. 2. SECTION GROUND-SET FLAGPOLES Specifications attached. END OF ADDENDUM

2 SECTION DOOR HARDWARE PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Mechanical door hardware for the following: a. Swinging doors. b. Sliding doors. c. Folding doors. 2. Cylinders for door hardware specified in other Sections. 3. Electrified door hardware. 1.2 PREINSTALLATION MEETINGS A. Preinstallation Conference: Conduct conference at Project site B. Keying Conference: Conduct conference at Project site 1.3 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: For electrified door hardware. 1. Include diagrams for power, signal, and control wiring. 2. Include details of interface of electrified door hardware and building safety and security systems. C. Samples: For each exposed product in each finish specified. D. Door hardware schedule. E. Other Action Submittals: 1. Door Hardware Schedule: Prepared by or under the supervision of Installer, detailing fabrication and assembly of door hardware, as well as installation procedures and diagrams. Coordinate final door hardware schedule with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware. a. Format: Use same scheduling sequence and format using the same door numbers as in the Contract Documents

3 F. Keying schedule. b. Content: Include the following information: 1) Identification number, location, hand, fire rating, size, degree of opening, and material of each door and frame. 2) Locations of each door hardware set, cross-referenced to Drawings on floor plans and to door and frame schedule. 3) Complete designations, including name and manufacturer, type, style, function, size, quantity, function, and finish of each door hardware product. 4) Description of electrified door hardware sequences of operation and interfaces with other building control systems. 5) ÓVertical scheduling format only. ÓHorizontal schedules will be returned without review noted ÓRESUBMIT. 1. Coordinate with Owner s Master System. 1.4 INFORMATIONAL SUBMITTALS A. Sample warranty. 1.5 CLOSEOUT SUBMITTALS A. Maintenance data. 1.6 QUALITY ASSURANCE A. Installer Qualifications: Supplier of products and an employer of workers trained and approved by product manufacturers and of an Architectural Hardware Consultant who is available during the course of the Work to consult Contractor, Architect, and Owner about door hardware and keying. 1. Scheduling Responsibility: Preparation of door hardware and keying schedule. 2. Engineering Responsibility: Preparation of data for electrified door hardware, including Shop Drawings, based on testing and engineering analysis of manufacturer's standard units in assemblies similar to those indicated for this Project. 1.7 WARRANTY A. Refer to Division 1 for warranty requirements. B. Special Warranty Periods: 1. Closers shall carry manufacturer's 30-year warranty against manufacturing defects and workmanship

4 2. Locksets shall carry manufacturer's 3-year warranty against manufacturing defects and workmanship. 3. Exit Devices shall carry manufacturer's 3-year warranty against manufacturing defects and workmanship. 4. Continuous gear hinges shall carry manufacturer's lifetime warranty to be free from defects in material and workmanship. 5. Balance of items shall carry a manufacturer's 1-year warranty against manufacturing defects and workmanship. C. During the warranty period, replace defective work, including labor, materials and other costs incidental to the work. 1.8 DELIVERY, STORAGE, AND HANDLING A. Deliver keys to manufacturer of key control system for subsequent delivery to Owner. B. Deliver keys and permanent cores to Owner by registered mail or overnight package service. PART 2 - PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Fire-Rated Door Assemblies: Where fire-rated doors are indicated, provide door hardware complying with NFPA 80 that is listed and labeled by a qualified testing agency, for fire-protection ratings indicated, based on testing at positive pressure according to NFPA 252 or UL 10C. B. Smoke- and Draft-Control Door Assemblies: Where smoke- and draft-control door assemblies are required, provide door hardware that complies with requirements of assemblies tested according to UL 1784 and installed in compliance with NFPA Air Leakage Rate: Maximum air leakage of 0.3 cfm/sq. ft. at the tested pressure differential of Insert value of water. C. Electrified Door Hardware: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. D. Means of Egress Doors: Latches do not require more than 15 lbf to release the latch. Locks do not require use of a key, tool, or special knowledge for operation. E. Accessibility Requirements: For door hardware on doors in an accessible route, comply with the DOJ's "2010 ADA Standards for Accessible Design". 1. Provide operating devices that do not require tight grasping, pinching, or twisting of the wrist and that operate with a force of not more than 5 lbf. 2. Comply with the following maximum opening-force requirements:

5 a. Interior, Non-Fire-Rated Hinged Doors: 5 lbf applied perpendicular to door. b. Sliding or Folding Doors: 5 lbf applied parallel to door at latch. c. Fire Doors: Minimum opening force allowable by authorities having jurisdiction. 3. Bevel raised thresholds with a slope of not more than 1:2. Provide thresholds not more than 1/2 inch high and 3/4 inch high for exterior sliding doors. 4. Closers: Adjust door and gate closer sweep periods so that, from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum. 5. Spring Hinges: Adjust door and gate spring hinges so that, from an open position of 70 degrees, the time required to move the door to the closed position is 1.5 seconds minimum. 2.2 SCHEDULED DOOR HARDWARE A. Provide products for each door that comply with requirements indicated in Part 2 and door hardware schedule. 1. Door hardware is scheduled in Part 3. B. Where only one manufacturer or product is listed, it is understood that this is the owner s Building Standard and no substitutions are allowed 2.3 HINGES A. Hinges: BHMA A Provide template-produced hinges for hinges installed on hollow-metal doors and hollow-metal frames. a. Ives; an Allegion Company. b. McKinney Products Company; an Assa Abloy Group Company. c. Stanley Commercial Hardware, a division of Stanley Security Solutions. 2.4 SELF-CLOSING HINGES AND PIVOTS A. Manufacturers: Subject to compliance with requirements, available manufacturers offering Products that may be incorporated into the work include: 1. Ives; an Allegion Company. 2. McKinney Products Company; an Assa Abloy Group Company. 3. Stanley Commercial Hardware, a division of Stanley Security Solutions

6 2.5 CENTER-HUNG AND OFFSET PIVOTS A. Center-Hung and Offset Pivots: BHMA A a. Ives; an Allegion Company. b. Dorma Americas. c. Rixson Specialty Door Controls; an Assa Abloy Group Company. 2.6 CONTINUOUS HINGES A. Continuous Hinges: BHMA A156.26; minimum inch- thick, hinge leaves with minimum overall width of 4 inches; fabricated to full height of door and frame and to template screw locations; with components finished after milling and drilling are complete. B. Pin-and-Barrel-Type Hinges: a. Ives; an Allegion Company. b. McKinney Products Company, an Assa Abloy Group Company. c. Stanley Commercial Hardware; a division of Stanley Security Solutions. C. Continuous, Gear-Type Hinges: Extruded-aluminum, pinless, geared hinge leaves joined by a continuous extruded-aluminum channel cap; with concealed, self-lubricating thrust bearings. a. Ives; an Allegion Company. b. McKinney Products Company, an Assa Abloy Group Company. c. Stanley Commercial Hardware; a division of Stanley Security Solutions. 2.7 MECHANICAL LOCKS AND LATCHES A. Lock Functions: As indicated in door hardware schedule. B. Lock Throw: Comply with testing requirements for length of bolts required for labeled fire doors, and as follows: 1. Bored Locks: Minimum 1/2-inch latchbolt throw. 2. Mortise Locks: Minimum 3/4-inch latchbolt throw. 3. Deadbolts: Minimum 1-inch bolt throw. C. Lock Backset: 2-3/4 inches unless otherwise indicated

7 D. Lock Trim: 1. Description: Insert description or manufacturer's design designation. 2. Dummy Trim: Match lever lock trim and escutcheons. E. Strikes: Provide manufacturer's standard strike for each lock bolt or latchbolt complying with requirements indicated for applicable lock or latch and with strike box and curved lip extended to protect frame; finished to match lock or latch. 1. Curved-Lip Strikes only as recommended by manufacturer. 2. Extended-Lip Strikes: For locks used on frames with applied wood casing trim. 3. Aluminum-Frame Strike Box: Manufacturer's special strike box fabricated for aluminum framing. 4. Rabbet Front and Strike: Provide on locksets for rabbeted meeting stiles. F. Bored Locks: BHMA A156.2; Grade 1; Series a. Falcon; an Allegion Company. b. Best Access Systems; Stanley Security Solutions, Inc. c. Sargent Manufacturing Company; an Assa Abloy Group Company. G. Mortise Locks: BHMA A156.13; Operational Grade 1 and Security Grade 1; stamped steel case with steel or brass parts; Series a. Best Access Systems; Stanley Security Solutions, Inc. b. Sargent, an Assa Abloy Group Company. c. Schlage; an Allegion Company. 2.8 AUXILIARY LOCKS A. Bored Auxiliary Locks: BHMA A156.36: Grade 1; with strike that suits frame. a. Best Access Systems; Stanley Security Solutions, Inc. b. Sargent Manufacturing Company; an Assa Abloy Group Company. c. Schlage; an Allegion Company. B. Mortise Auxiliary Locks: BHMA A156.36; Grade 1; with strike that suits frame. a. Best Access Systems; Stanley Security Solutions, Inc

8 b. Sargent Manufacturing Company; an Assa Abloy Group Company. c. Schlage; an Allegion Company. C. Narrow Stile Auxiliary Locks: BHMA A156.36; Grade 1; with strike that suits frame. a. Accurate Lock & Hardware Co. b. Adams Rite Manufacturing; an Assa Abloy Group Company. c. Kaba Ilco Corp. 2.9 ELECTRIC STRIKES A. Electric Strikes: BHMA A156.31; Grade 1; with faceplate to suit lock and frame. a. Hanchett Entry Systems; an Assa Abloy Group Company. b. Von Duprin; an Allegion Company ELECTROMAGNETIC LOCKS A. Electromagnetic Locks: BHMA A156.23; electrically powered; with electromagnet attached to frame and armature plate attached to door; full-exterior or full-interior type, as required by application indicated. a. Von Duprin; an Allegion Company. b. Securitron; an Assa Abloy Group Company. B. Delayed-Egress Electromagnetic Locks: BHMA A156.24, electrically powered, with electromagnet attached to frame and armature plate attached to door; depressing push bar for more than three seconds initiates irreversible alarm and adjustable time delay for egress. When integrated with fire alarm, fire alarm voids time delay. a. Von Duprin; an Allegion Company. b. Securitron; an Assa Abloy Group Company ELECTROMECHANICAL LOCKS A. Electromechanical Locks: BHMA A156.25; Grade 1; motor driven; with strike that suits frame

9 a. Best Access Systems; Stanley Security Solutions, Inc. b. Sargent Manufacturing Company; an Assa Abloy Group Company. c. Schlage; an Allegion Company SELF-CONTAINED ELECTRONIC LOCKS A. Self-Contained Electronic Locks: BHMA A156.25, [bored] [mortise]; with internal, battery-powered, self-contained electronic locks; consisting of complete lockset, motor-driven lock mechanism, and actuating device; enclosed in zinc-dichromate-plated, wrought-steel case, and strike that suits frame. Provide key override, low-battery detection and warning, LED status indicators, and ability to program at the lock. a. Best Access Systems; Stanley Security Solutions, Inc. b. Sargent Manufacturing Company; an Assa Abloy Group Company. c. Schlage; an Allegion Company EXIT LOCKS AND EXIT ALARMS A. Exit Locks and Alarms: BHMA A156.29, Grade 1. a. Von Duprin; an Allegion Company. b. Precision Hardware Inc., a Stanley Company SURFACE BOLTS A. Surface Bolts: BHMA A a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco MANUAL FLUSH BOLTS A. Manual Flush Bolts: BHMA A156.16; minimum 3/4-inch throw; designed for mortising into door edge

10 a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco AUTOMATIC AND SELF-LATCHING FLUSH BOLTS A. Automatic and Self-Latching Flush Bolts: BHMA A156.16; minimum 3/4-inch throw; designed for mortising into door edge. Include wear plates. a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco EXIT DEVICES AND AUXILIARY ITEMS A. Exit Devices and Auxiliary Items: BHMA A a. Von Duprin; an Allegion Company. b. Precision Hardware Inc., a Stanley Company LOCK CYLINDERS A. Lock Cylinders: Tumbler type, constructed from brass or bronze, stainless steel, or nickel silver. Provide cylinder from same manufacturer of locking devices. a. Schlage; an Allegion Company. b. Best Access Systems; Stanley Security Solutions, Inc. c. Sargent Manufacturing Company; Assa Abloy. B. Standard Lock Cylinders: BHMA A156.5; Grade 1 permanent cores; face finished to match lockset. 1. Core Type:. Coordinate with owner. C. High-Security Lock Cylinders: BHMA A156.30; Grade 1 permanent cores that are removable; face finished to match lockset

11 1. Type: M, mechanical. D. Construction Master Keys: Provide cylinders with feature that permits voiding of construction keys without cylinder removal. Provide 10 construction master keys. E. Construction Cores: Provide construction cores that are replaceable by permanent cores. Provide 10 construction master keys KEYING A. Keying System: Factory registered, complying with guidelines in BHMA A156.28, appendix. Provide one extra key blank for each lock. Incorporate decisions made in keying conference. 1. No Master Key System: Only change keys operate cylinders. a. Provide three cylinder change keys. 2. Master Key System: Change keys and a master key operate cylinders. a. Provide three cylinder change keys and five master keys. 3. Grand Master Key System: Change keys, a master key, and a grand master key operate cylinders. a. Provide three cylinder change keys and five each of master and grand master keys. 4. Great-Grand Master Key System: Change keys, a master key, a grand master key, and a great-grand master key operate cylinders. a. Provide three cylinder change keys and five each of master, grand master, and great-grand master keys. 5. Existing System: a. Master key or grand master key locks to Owner's existing system. b. Re-key Owner's existing master key system into new keying system. 6. Keyed Alike: Key all cylinders to same change key. B. Keys: Nickel silver. 1. Stamping: Permanently inscribe each key with a visual key control number and include the following notation: a. Notation: Information to be furnished by Owner

12 2.20 KEY CONTROL SYSTEM A. Key Control Cabinet: BHMA A156.28; metal cabinet with baked-enamel finish; containing key-holding hooks, labels, two sets of key tags with self-locking key holders, key-gathering envelopes, and temporary and permanent markers; with key capacity of [150] <Insert number> percent of the number of locks. a. American Key Boxes and Cabinets. b. GE Security, Inc. c. HPC, Inc. d. Lund Equipment Company, Inc. e. MMF Industries. f. Telkee; Oasis International. 2. Wall-Mounted Cabinet: Grade 1 cabinet with hinged-panel door equipped with key-holding panels and pin-tumbler cylinder door lock ACCESSORIES FOR PAIRS OF DOORS A. Coordinators: BHMA A156.3; consisting of active-leaf, hold-open lever and inactive-leaf release trigger; fabricated from steel with nylon-coated strike plates; with built-in, adjustable safety release; and with internal override. B. Carry-Open Bars: BHMA A156.3; prevent the inactive leaf from opening before the active leaf; provide polished brass or bronze carry-open bars with strike plate for inactive leaves of pairs of doors unless automatic or self-latching bolts are used. C. Astragals: BHMA A a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco SURFACE CLOSERS A. Surface Closers: BHMA A156.4; cast iron, rack-and-pinion hydraulic type with adjustable sweep and latch speeds controlled by key-operated valves and forged-steel main arm. Comply with manufacturer's written instructions for size of door closers depending on size of door, exposure to weather, and anticipated frequency of use. Provide factory-sized closers, adjustable to meet field conditions and requirements for opening force

13 a. LCN; an Allegion Company CONCEALED CLOSERS A. Concealed Closers: BHMA A156.4; cast iron, rack-and-pinion hydraulic type with adjustable sweep and latch speeds controlled by key-operated valves. Comply with manufacturer's written instructions for size of door closers depending on size of door, exposure to weather, and anticipated frequency of use. Provide factory-sized closers, adjustable to meet field conditions and requirements for opening force. a. LCN; an Allegion Company CLOSER HOLDER RELEASE DEVICES A. Closer Holder Release Devices: BHMA A156.15; cast iron, Grade 1 closer connected with separate or integral releasing and fire- or smoke-detecting devices. Door shall become self-closing on interruption of signal to release device. Automatic release is activated by loss of power. a. LCN; an Allegion Company MECHANICAL STOPS AND HOLDERS A. Wall- and Floor-Mounted Stops: BHMA A a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco ELECTROMAGNETIC STOPS AND HOLDERS A. Electromagnetic Door Holders: BHMA A156.15, Grade 1; wall-mounted electromagnetic single unit with strike plate attached to swinging door; coordinated with fire detectors and interface with fire-alarm system for labeled fire-rated door assemblies

14 a. LCN; an Allegion Company. b. Rixson, an Assa Abloy Group Company. c. Sargent Manufacturing Company; an Assa Abloy Group Company OVERHEAD STOPS AND HOLDERS A. Overhead Stops and Holders: BHMA A a. Glynn Johnson; an Allegion Company. b. Sargent Manufacturing Company; Assa Abloy DOOR GASKETING A. Door Gasketing: BHMA A156.22; with resilient or flexible seal strips that are easily replaceable and readily available from stocks maintained by manufacturer. a. National Guard Products Inc. b. Pemko Manufacturing Co. c. Zero International, Inc. B. Maximum Air Leakage: When tested according to ASTM E 283 with tested pressure differential of 0.3-inch wg, as follows: 1. Smoke-Rated Gasketing: 0.3 cfm/sq. ft. of door opening. 2. Gasketing on Single Doors: 0.3 cfm/sq. ft. of door opening. 3. Gasketing on Double Doors: 0.50 cfm per foot of door opening THRESHOLDS A. Thresholds: BHMA A156.21; fabricated to full width of opening indicated. a. National Guard Products Inc. b. Pemko Manufacturing Co. c. Zero International, Inc

15 2.30 SLIDING DOOR HARDWARE A. Sliding Door Hardware: BHMA A156.14; consisting of complete sets including rails, hangers, supports, bumpers, floor guides, and accessories indicated. a. Brio b. Johnson, LE Products, Inc. c. Stanley Commercial Hardware; a division of Stanley Security Solutions FOLDING DOOR HARDWARE A. General: BHMA A156.14; complete sets including overhead rails, hangers, supports, bumpers, floor guides, and accessories indicated. a. Arthur Cox & Sons, Inc. b. Johnson, LE Products, Inc. c. Stanley Commercial Hardware; a division of Stanley Security Solutions METAL PROTECTIVE TRIM UNITS A. Metal Protective Trim Units: BHMA A156.6; fabricated from inch- thick stainless steel; with manufacturer's standard machine or self-tapping screw fasteners. a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco AUXILIARY DOOR HARDWARE A. Auxiliary Hardware: BHMA A a. Ives; an Allegion Company. b. Rockwood Manufacturing; an Assa Abloy Group Company. c. Trimco

16 2.34 AUXILIARY ELECTRIFIED DOOR HARDWARE A. Auxiliary Electrified Door Hardware: a. Best Access Systems; Stanley Security Solutions, Inc. b. Sargent Manufacturing Company; an Assa Abloy Group Company. c. Schlage; an Allegion Company FINISHES A. Provide finishes complying with BHMA A as indicated in door hardware schedule. PART 3 - EXECUTION 3.1 INSTALLATION A. Mounting Heights: Mount door hardware units at heights to comply with the following unless otherwise indicated or required to comply with governing regulations. 1. Standard Steel Doors and Frames: ANSI/SDI A Custom Steel Doors and Frames: HMMA Wood Doors: DHI's "Recommended Locations for Architectural Hardware for Wood Flush Doors." B. Install each door hardware item to comply with manufacturer's written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work. Do not install surface-mounted items until finishes have been completed on substrates involved. C. Hinges: Install types and in quantities indicated in door hardware schedule, but not fewer than the number recommended by manufacturer for application indicated or one hinge for every 30 inches of door height, whichever is more stringent, unless other equivalent means of support for door, such as spring hinges or pivots, are provided. D. Intermediate Offset Pivots: Where offset pivots are indicated, provide intermediate offset pivots in quantities indicated in door hardware schedule, but not fewer than one intermediate offset pivot per door and one additional intermediate offset pivot for every 30 inches of door height greater than 90 inches. E. Lock Cylinders: Install construction cores to secure building and areas during construction period. 1. Replace construction cores with permanent cores as directed by Owner. 2. Furnish permanent cores to Owner for installation

17 F. Key Control Cabinet: Tag keys and place them on markers and hooks in key control system cabinet, as determined by final keying schedule. G. Thresholds: Set thresholds for exterior doors and other doors indicated in full bed of sealant complying with requirements specified in Section "Joint Sealants." H. Stops: Provide floor stops for doors unless wall or other type stops are indicated in door hardware schedule. Do not mount floor stops where they will impede traffic. I. Perimeter Gasketing: Apply to head and jamb, forming seal between door and frame. 1. Do not notch perimeter gasketing to install other surface-applied hardware. J. Meeting Stile Gasketing: Fasten to meeting stiles, forming seal when doors are closed. K. Door Bottoms: Apply to bottom of door, forming seal with threshold when door is closed. 3.2 ADJUSTING A. Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements. 3.3 DOOR HARDWARE SCHEDULE Hardware Set No EA A. HINGE 112XY 628 IVE 1 EA B. HINGE 112XY EPT 628 IVE 1 EA POWER TRANSFER EPT VON 1 EA REMOVABLE MULLION VON 1 EA PANIC HARDWARE 35A-EO 626 VON 1 EA ELEC PANIC HARDWARE HD-QEL-35A-NL-OP VDC 626 VON

18 1 EA RIM CYLINDER SCH 2 EA 90 DEG OFFSET PULL 8190EZHD 12" O IVE 2 EA OH STOP 100S 630 GLY 2 EA SURFACE CLOSER LCN 2 EA MOUNTING PLATE G 689 LCN 2 SET WEATHER SEAL (BY DOOR AND FRAME MFR) 2 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A-V3-223 A ZER 1 EA ACCESS CONTROL (BY SECURITY CONTRACTOR) 1 EA POWER SUPPLY PS RS VON PRESENTING AN AUTHORIZED CREDENTIAL WILL RETRACT THE EXIT DEVICE LATCHBOLT AND ALLOW ACCESS. FREE EGRESS IS ALWAYS ALLOWED. COORDINATE SYSTEM OPERATION AND COMPONENT LOCATIONS WITH THE OWNER, THE ARCHITECT AND ALL RELATED TRADES. Hardware Set No A EA C. HINGE 112XY 628 IVE 2 EA PUSH/PULL BAR 9190EZHD-12"-NO IVE 2 EA OH STOP 100S 630 GLY 2 EA SURFACE CLOSER LCN 2 EA MOUNTING PLATE G 689 LCN Hardware Set No A

19 1 EA D. HINGE 112XY 628 IVE 1 EA PUSH/PULL BAR 9190EZHD-12"-NO IVE 1 EA OH STOP 100S 630 GLY 1 EA SURFACE CLOSER LCN 1 EA MOUNTING PLATE G 689 LCN Hardware Set No B A 1 EA E. HINGE 112XY EPT 628 IVE 1 EA POWER TRANSFER EPT VON 1 EA ELEC PANIC HARDWARE HD-QEL-35A-NL-OP VDC 626 VON 1 EA RIM CYLINDER SCH 1 EA 90 DEG OFFSET PULL 8190EZHD 12" O IVE 1 EA OH STOP 100S 630 GLY 1 EA SURFACE CLOSER LCN 1 EA MOUNTING PLATE G 689 LCN 1 SET WEATHER SEAL (BY DOOR AND FRAME MFR) 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A-V3-223 A ZER 1 EA ACCESS CONTROL (BY SECURITY CONTRACTOR) 1 EA POWER SUPPLY PS RS VON PRESENTING AN AUTHORIZED CREDENTIAL WILL RETRACT THE EXIT DEVICE LATCHBOLT AND ALLOW ACCESS. FREE EGRESS IS ALWAYS ALLOWED. COORDINATE SYSTEM OPERATION AND COMPONENT LOCATIONS WITH THE

20 OWNER, THE ARCHITECT AND ALL RELATED TRADES. Hardware Set No EA SLIDING DOOR HW SD JSTP N N Sl 630 SCH 1 EA 90 DEG OFFSET PULL PR 8190EZHD 12" N IVE Hardware Set No EA HINGE 5BB1 4.5 X IVE 1 EA PUSH PLATE " X 16" 630 IVE 1 EA PULL PLATE " 4" X 16" 630 IVE 1 EA SURFACE CLOSER LCN 1 EA KICK PLATE " X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE Hardware Set No EA F. HINGE 224XY 628 IVE 1 EA STOREROOM LOCK L9080P LLL 17A L SCH 1 EA DOOR PULL VR IVE

21 1 EA SURFACE CLOSER 4111 SHCUSH SRI ST LCN 1 EA KICK PLATE " X 2" LDW B-CS 630 IVE 1 EA RAIN DRIP 142AA AA ZER 1 EA GASKETING 429AA-S AA ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A-V3-223 A ZER Hardware Set No A EA HINGE 5BB1 4.5 X IVE 1 EA STOREROOM LOCK ND80PD SPA 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE Hardware Set No EA G. HINGE 224XY EPT 628 IVE 1 EA POWER TRANSFER EPT VON 1 EA ELEC PANIC HARDWARE HD-QEL-98-NL-OP-110MD-24VDC 626 VON 1 EA RIM CYLINDER SCH 1 EA DOOR PULL VR910 NL 630 IVE 1 EA SURFACE CLOSER 4111 SCUSH 689 LCN

22 1 EA RAIN DRIP 142AA AA ZER 1 EA GASKETING 429AA-S AA ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A-V3-223 A ZER 1 EA ACCESS CONTROL (BY SECURITY CONTRACTOR) 1 EA POWER SUPPLY PS RS VON PRESENTING AN AUTHORIZED CREDENTIAL WILL RETRACT THE EXIT DEVICE LATCHBOLT AND ALLOW ACCESS. FREE EGRESS IS ALWAYS ALLOWED. COORDINATE SYSTEM OPERATION AND COMPONENT LOCATIONS WITH THE OWNER, THE ARCHITECT AND ALL RELATED TRADES. Hardware Set No A 2 EA HINGE 5BB1HW 4.5 X 4.5 NRP 652 IVE 1 EA ELECTRIC HINGE 5BB1HW 4.5 X 4.5 TW4 652 IVE 1 EA STOREROOM LOCK ND80PDEU SPA CON12V/24V DC 626 SCH 1 EA SURFACE CLOSER 4111 SCUSH 689 LCN 1 EA KICK PLATE " X 1" LDW B-CS 630 IVE 1 EA ACCESS CONTROL (BY SECURITY CONTRACTOR) 1 EA POWER SUPPLY PS RS VON PRESENTING AN AUTHORIZED CREDENTIAL WILL UNLOCK THE OUTSIDE TRIM AND ALLOW ACCESS. FREE EGRESS IS ALWAYS ALLOWED. COORDINATE SYSTEM OPERATION AND COMPONENT LOCATIONS WITH THE OWNER, THE ARCHITECT AND ALL RELATED TRADES. Hardware Set No

23 3 EA HINGE 5BB1 4.5 X IVE 1 EA CLASSROOM LOCK ND70PD SPA 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE Hardware Set No SET BI-FOLD HARDWARE 100FS JOH 2 EA DOOR PULL, 3/4" RND 8102HD 6" STD 630 IVE Hardware Set No A 118B 118C 118D EA * ALL HDWE BY THE DOOR MFR * Hardware Set No EA HINGE 5BB1HW 4.5 X 4.5 NRP 652 IVE 2 EA SURFACE BOLT SB453 8" TB 652 IVE 1 EA ENTRANCE/OFFICE LOCK ND50PD SPA 626 SCH

24 2 EA WALL STOP WS406/407CCV 630 IVE Hardware Set No EA HINGE 5BB1HW 4.5 X IVE 1 EA PRIVACY LOCK ND40S SPA 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA GASKETING 488SBK PSA BK ZER Hardware Set No EA HINGE 5BB1 4.5 X IVE 1 EA ENTRANCE/OFFICE LOCK ND50PD SPA 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA GASKETING 488SBK PSA BK ZER END OF SECTION Revision History Date Rev. No.?? 0 DO/dm CityOfJacksonFinishHardwareSpec docx

25 THIS PAGE INTENTIONALLY LEFT BLANK

26 SECTION GROUND-SET FLAGPOLES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes ground-set flagpoles made from aluminum. B. Owner-Furnished Material: Flags. 1.3 ACTION SUBMITTALS A. Product Data: For each type of product. 1. Include construction details, material descriptions, dimensions of individual components and profiles, operating characteristics, fittings, accessories, and finishes for flagpoles. B. Shop Drawings: For flagpoles. 1. Include plans, elevations, and attachment details. Show general arrangement, jointing, fittings, accessories, grounding, anchoring, and support. 2. Include section, and details of foundation system. C. Samples for Verification: For each type of exposed finish, in manufacturer's standard sizes. 1.4 CLOSEOUT SUBMITTALS A. Operation and Maintenance Data: For flagpoles to include in operation and maintenance manuals. 1.5 DELIVERY, STORAGE, AND HANDLING A. Spiral wrap flagpoles with heavy paper and enclose in a hard fiber tube or other protective container Revision No.0

27 PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Source Limitations: Obtain flagpoles as complete units, including fittings, accessories, bases, and anchorage devices, from single source from single manufacturer. 2.2 PERFORMANCE REQUIREMENTS A. Delegated Design: Engage a qualified professional engineer, as defined in Section "Quality Requirements," to design flagpole assemblies. B. Seismic Performance: Flagpole assemblies shall withstand the effects of earthquake motions determined according to ASCE/SEI 7. C. Structural Performance: Flagpole assemblies, including anchorages and supports, shall withstand design loads indicated within limits and under conditions indicated. 1. Wind Loads: Determine according to NAAMM FP Basic wind speed for Project location is 115mph, 3 second gust. 2. Base flagpole design on nylon or cotton flags of maximum standard size suitable for use with flagpole or flag size indicated, whichever is more stringent. 2.3 ALUMINUM FLAGPOLES A. Aluminum Flagpoles: Cone-tapered flagpoles fabricated from seamless extruded tubing complying with ASTM B241/B241M, Alloy 6063, with a minimum wall thickness of 3/16 inch. 1. American Flagpole 2. Concord Industries, Inc. 3. U.S. Flag & Flagpole Supply, LP B. Exposed Height: One (1) at 30 feet. C. Construct flagpoles in one piece if possible. If more than one piece is necessary, comply with the following: 1. Fabricate shop and field joints without using fasteners, screw collars, or lead calking. 2. Provide flush hairline joints using self-aligning, snug-fitting, internal sleeves. D. Metal Foundation Tube: Manufacturer's standard corrugated-steel foundation tube, inch wall thickness with 3/16-inch steel bottom plate and support plate; 3/4-inch diameter, steel ground spike; and steel centering wedges welded together. Galvanize foundation tube after assembly. Furnish loose hardwood wedges at top of foundation tube for plumbing pole. 1. Flashing Collar: Same material and finish as flagpole Revision No.0

28 E. Sleeve for Aluminum Flagpole: Fiberglass or PVC pipe foundation sleeve, made to fit flagpole, for casting into concrete foundation. 1. Flashing Collar: Same material and finish as flagpole. F. Cast-Metal Shoe Base: Made from aluminum with same finish and color as flagpoles for anchor-bolt mounting; furnish with anchor bolts. 1. Furnish ground spike. 2.4 FITTINGS A. Finial Ball: Flush-seam ball, sized as indicated or, if not indicated, to match flagpole-butt diameter inch spun aluminum with gold anodic finish. B. Internal Halyard, Winch System: Manually operated winch with control stop device and removable handle, stainless-steel cable halyard, and concealed revolving truck assembly with plastic-coated counterweight and sling. Furnish flush access door secured with cylinder lock. Finish truck assembly to match flagpole. 1. Halyard Flag Snaps: Chromium-plated bronze swivel snap hooks. Furnish two per halyard. 2.5 MISCELLANEOUS MATERIALS A. Nonshrink, Nonmetallic Grout: Factory-packaged, nonstaining, noncorrosive, nongaseous grout complying with ASTM C1107/C1107M. B. Drainage Material: Crushed stone, or crushed or uncrushed gravel; coarse aggregate. C. Sand: ASTM C33/C33M, fine aggregate. D. Elastomeric Joint Sealant: Multicomponent nonsag urethane joint sealant complying with requirements in Section "Joint Sealants." E. Bituminous Paint: Cold-applied asphalt emulsion complying with ASTM D1187/D1187M. 2.6 ALUMINUM FINISHES A. Powder-Coat Finish: AAMA 2603 except with a minimum dry film thickness of 1.5 mils. Comply with coating manufacturer's written instructions for cleaning, conversion coating, and applying and baking finish. 1. Color and Gloss: White Revision No.0

29 PART 3 - EXECUTION 3.1 PREPARATION A. Prepare uncoated metal flagpoles that are set in foundation tubes by painting below-grade portions with a heavy coat of bituminous paint. B. Foundation Excavation: Excavate to neat clean lines in undisturbed soil. Remove loose soil and foreign matter from excavation and moisten earth before placing concrete. Place and compact drainage material at excavation bottom. C. Provide forms where required due to unstable soil conditions and for perimeter of flagpole base at grade. Secure and brace forms to prevent displacement during concreting. D. Foundation Tube: Place foundation tube, center, and brace to prevent displacement during concreting. Place concrete. Plumb and level foundation tube and allow concrete to cure. E. Sleeves: Locate and secure sleeves in forms by bracing to reinforcement and forms. F. Anchor Bolts: Locate and secure anchor bolts in forms with templates and by tying to reinforcement. G. Place concrete, as specified in Section "Cast-in-Place Concrete." Compact concrete in place by using vibrators. Moist-cure exposed concrete for no fewer than seven days or use nonstaining curing compound. H. Trowel exposed concrete surfaces to a smooth, dense finish, free of trowel marks, and uniform in texture and appearance. Provide positive slope for water runoff to perimeter of concrete base. 3.2 FLAGPOLE INSTALLATION A. General: Install flagpoles where indicated and according to manufacturer's written instructions. B. Foundation Tube: Place flagpole in tube, seated on bottom plate between steel centering wedges, and install hardwood wedges to secure flagpole in place. Place and compact sand in foundation tube and remove hardwood wedges. Seal top of foundation tube with a 2-inch layer of elastomeric joint sealant and cover with flashing collar. C. Baseplate: Cast anchor bolts in concrete foundation. Install baseplate on washers placed over leveling nuts on anchor bolts and adjust until flagpole is plumb. After flagpole is plumb, tighten retaining nuts and fill space under baseplate solidly with nonshrink, nonmetallic grout. Finish exposed grout surfaces smooth and slope 45 degrees away from edges of baseplate. END OF SECTION Revision No.0

30 THIS PAGE INTENTIONALLY LEFT BLANK Revision No.0