luxcontrol lighting control system basicdim basicdim ILD 5DPI 14f Compact control module with ambient light sensor and motion sensor

Transcription

1 luxcontrol lighting control sstem ILD 5DPI 14f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 1 DSI or LI devices (max. 5 per output channel) LI/DSI output channels with adjustable negative offset from channel to channel 1 Ambient light sensor with motion detector Max. installation height 5 m Switch input for on/off switching and dimming Can be remote controlled Individual adjustment of the parameters with ILD Programmer or DSI-SMART Programmer 5-ear guarantee ILD 5DPI 14F È Wiring diagrams and installation examples, page 7 ILD 5DPI 14F Black ILD 5DPI 14F Black 1.8m 1

2 luxcontrol lighting control sstem ILD 5DPI 14f Compact control module with ambient light sensor and motion sensor Technical data Rated suppl voltage 4 V Mains frequenc 5 / 6 Hz Power W Stand-b power.5 W Momentar-action switch input for dimming single Digital control line DSI/LI Control output (devices) 1 Max. output cable length at 1.5 mm² 1 m Operating temperature C Storage temperature C Tpe of protection IP Max. casing temperature tc 75 C ,4 44,4 1,8 Ø13,9 1,9 3 Ordering data Tpe Article number Mounting Packaging carton ILD 5DPI 14f 813 Luminaire installation 1 pc(s). ILD 5DPI 14f Black 8159 Luminaire installation 1 pc(s). ILD 5DPI 14f Black 1.8m 8158 Luminaire installation 1 pc(s). Illuminance (factor default) Motion detection angle smmetric Specific technical data Tpe Detection Light detection angle Light measurement at Max. cable length sensor asmmetric the sensor head 1 ILD 5DPI 14f lx 15 lx 78.8 m ILD 5DPI 14f Black lx 15 lx 78.8 m ILD 5DPI 14f Black 1.8m lx 15 lx m 1 The measured value at the sensor head corresponds to approx. 15 to, lux on the surface measured. The illuminance is set for a room defined b Tridonic. Depending on the actual room (reflectance) the measured illuminance ma deviate from this value. The illuminance should therefore be checked in the installation and adjusted if necessar.

3 luxcontrol lighting control sstem ACCES- SORIES REMOTECONTROL IR6 Product description Optional infra-red remote control Switching on and off (On/Off button) Dimming (Up/Down button) Activation of automatic lighting control Setting the threshold control point (Set button) Ordering data Tpe Article number Dimensions L x W x H Packaging carton REMOTECONTROL IR x 4.5 x 7. mm 5 pc(s). ACCES- SORIES ILD Programmer Product description Optional infra-red programming unit for ILD Setting of predefined discrete parameter values Programmable functions such as light level, time dela, P.I.R., bright-out, power up Ordering data Tpe Article number Packaging carton Weight per pc. ILD Programmer pc(s)..3 kg 3

4 luxcontrol lighting control sstem ACCES- SORIES DSI SMART Programmer Product description Optional infra-red programming unit for DSI-SMART PTM or ILD 1 44,5 1 Settings can be read and modified Programmable functions such as light level, time dela, P.I.R., bright-out, power up 18 Ordering data Tpe Article number Packaging carton Weight per pc. DSI-SMART Programmer pc(s)..35 kg 1 At version.3 for ILD. ACCES- SORIES 5DPI 14f Mounting Kit Product description Mounting frame for attaching all 5DP 14f sensor directl to the luminaire housing Shutter for preventing movement detection in one direction Ordering data Tpe Article number Packaging carton Weight per pc. 5DPI 14f mounting kit pc(s)..4 kg 5DPI 14f mounting kit black pc(s)..4 kg 4

5 luxcontrol lighting control sstem ILD The basic DIM ILD provides the basis for an eas-to-use and cost-effective lighting sstem with motion detection. When the sensor detects movement it triggers a individual adjustable motion detection profile in the control unit. As the amount of natural ambient light changes the illuminance from the artificial lighting sstem is adjusted. The connected luminaires can be switched on and off via momentar-action switch or remote control possible. IR is alwas active. Standards EN 5515 EN EN EN EN EN Glow-wire test according to EN passed. LI standard The ILD is designed to control control gear with LI standard IEC 699 (LI V) and IEC 6386 (LI V1). Installation Don t use the ILD without the sensor. DSI/LI is not SELV. The installation instructions for mains voltage therefore appl. The maximum cable length between the external switch and ILD is 1 m. The cable between the luminaire installation sensor and the base module must not be extended. A snchronous operation of LI and DSI ballasts at the same control gear is not possible. The maximum cable length of the DSI / LI control signal (for a cable cross-section of 1,5 m ) must not be exceeded. An number of push to make switches ma be connected in parallel to the inputs. Do not connect standard switches to the input. Please ensure that the detection range of the sensor lies in the lighting area of the controlled luminaires. Please ensure that the detection ranges of the sensors do not overlap. This ma have influence to the lighting control. Heaters, fans, printers and copiers located in the detection zone ma cause incorrect presence detection. To avoid false readings, the sensor should be installed so there is no direct light from the lamp in the detection zone. To avoid false measurements caused b the light from other luminaires we recommend that the sensor should be located centrall in the luminaire. Sensor wires must be routed separatel from the lamp wires and mains cables otherwise the lighting control sstem ma malfunction. If separate routing is not possible (for reasons of space) shielded lamp wires and mains cables must be used. Mounting variants luminair housing: Size of the sheet: mm Size of the sheet:.6.8 mm 1,5,5 19,1 ø14,1 +,, +, 4 +, +,1 -,1 ø1,8 +,1 3, -,15 Size of the sheet:.8 3. mm 3,3 5,5 41,1 +, 14,1 +, R1,9 -, 5

6 luxcontrol lighting control sstem Mounting in luminaire housing with Mounting Kit: Size of the sheet:.8. mm Dimension drawing for needed mounting opening, ø1, +,1 R,9 1,8±,5 Shutter support ring has to be snapped into the shutter support Thickness metal sheet.8. mm.8 1,65±,5 Option shutter: has to be snapped into the shutter support ring Mounting Kit mounting Mounting Kit Shutter Area which is masked b the shutter

7 luxcontrol lighting control sstem Switch ILD has an input terminal for an external switch. An number of switches can be connected in parallel to the terminal. Short press (> 5 6 ms): Long press (> 6 ms): ON/OFF Dim up/down A change in the light value deactivates lighting regulation onl temporaril. As soon as the luminaire has been automaticall switched on again (motion detection) or manuall switched off and on again, regulation is activated again. x short press: The overwritten setpoint light value is stored (luminaire acknowledges b flashing twice) Function is lockable via the DSI programmer DSI/LI interface The interface selection DSI or LI is made b the DSI SMART Programmer. Wiring diagram ILD L N Cable tpes and cable cross-sections Solid wire with a cable cross-section of.5 mm² to 1.5 mm². wire preparation: mm² PCA 8 9 mm L N T ILD CH1 D1 D 3 4 PCA Sensor CH D1 D 6 7 ILD Sensor Enhancement of controllable light point B using a combination of LI Repeater and LI Power Suppl it is possible to enhance the sum of controllable light points. The schematic visualizes the wiring. L N Max. Max LCA N ~ L PS LCA L N T ILD CH1 D1 D Sensor CH D1 D IN LI Repeater OUT ILD Sensor Use onl in combination with LI Repeater ( ) and one of the following LI Power Supplies: LI PS1 (43433), ma, max. 1 additional devices LI PS (8876), 4 ma, max. 1 additional devices Wire length for 1.5 mm cables: from to LI Repeater max. 1 m after LI Repeater max. 3 m This combination can be used on CH1 and CH. 7

8 luxcontrol lighting control sstem Light level recognition area Sensor alignment h α = α = 38 α = 3 38 h h * d 1.7 m 1.3 m.7 m 1. m.8 m. m 1.6 m.8 m 1. m 3. m.3 m 1.8 m.9 m 1.3 m 3.7 m.5 m. m 1. m 1.4 m 4. m.7 m.1 m 1.1 m 1.6 m 4.4 m 3. m.3 m 1. m 1.7 m 4.9 m 3.5 m.7 m 1.4 m. m 5.7 m 4. m 3.1 m 1.6 m.3 m 6.5 m * The recommended maximum room height for office applications is 3 m and for corridor applications for example 4 m. Up to m mounting height presence is detected and over m motion is detected. Calculation of the diameter (light area): = tan(a) h = tan(a) h = tan(a) h Calculation of the diameter (motion area): d = tan(,5 a) h Example for light and motion detection area at height of 1.7 m: 1 m.7 m 1.3 m Light level recognation area 1 m Presence / motion detection.8 m Presence / motion detection h α = 78 d 8

9 luxcontrol lighting control sstem The following operating modes can be set for the motion detector via the ILD Programmer or DSI-Smart Programmer: Active Off Onl Never Off Inactive The light is switched on or off automaticall depending on whether or not there is a person in the room. The motion detector onl switches the connected lighting off. The luminaires are switched on manuall via the connected external switch or infra-red control. If it has not detected an movement the sensor dims to the second light value parameter and remains at this value The motion sensor is deactivated. The light must be switched on or off manuall. Switch-off dela This is the time after which the lighting is switched off if no movement is detected. It can be set via the time dela parameter. Second light value On the ILD ou can set whether the light is to be switched off after the switch-off dela or dimmed to the second light value. The light value and the dwell time (how long the value is held) can be set via the when vacant and sec. level parameters. Offset The light level of channel is less then the light level of channel 1. The difference can be set with the parameter Offset Value via ILD Programmer or DSI-SMART Programmer. Channel Channel 1 4 % 7 % 5 LUX Artificial light Natural light Manual-off dela If the sstem is switched off manuall via the switch or remote control the motion sensor is deactivated. At the end of a 1 minutes dela if motion has not been detected the motion sensor is activated again. If the sensor detects motion during the Manual Off dela, the time will be reset to the start. The following operating modes can be set for lighting control via the DSI-Smart Programmer: Active Inactive Constant light control is active. Constant light control is deactivated. The lighting is switched on at 1%. The value is set with the light-level parameter. If the value is set to max then lighting control is deactivated. For all other values lighting control is active. Setpoint adjustment DSI-SMART Controller: Pressing the Set button stores the current light value as a new setpoint. ILD Programmer or DSI-SMART Programmer: Via the light-level parameter External switch: Briefl pressing the switch twice stores the current light value as a new setpoint. (Function is lockable via the ILD Programmer or DSI Programmer) Bright-out If the nominal illuminance (e.g. 5 lux) is exceeded for 1 minutes b more than 15 % (e.g. 75 lux), the lighting is switched off even if motion is detected. The lighting is switched on again when the measured light value falls below the setpoint. The bright-out function is displaed b a green status indication LED at the sensor. This function can be deactivated via the ILD Programmer or DSI-SMART Programmer. 9

10 luxcontrol lighting control sstem User-definable parameters ILD have the following user-definable parameters (since DSI-SMART Programmer version.3): The values in parentheses are the factor default settings. The adjustable values for the ILD Programmer is available in a separatel documentation on Parameter light-level time dela if vacant Range (Factor setting) 1 1/max (7) 3 s 6 min/con ( min) off 3 s 6 min/con (off) sec. level 1 1 % (1 %) P.I.R active/inactive/off onl (active) bright-out Power up hold overwrite PTM Set LIorDSI Offset Mode es/no (es) on/off (on) on/off (off) on/off (on) DSI/LI (DSI) fixed/converging (converging) Offset Value to -7 % (-3 %) Description Selectable lighting control set point, 1 1 increments. max also makes it possible to set the control gear to full power. (DSI 55) man indicates whether the adjustment value was overwritten b the SET function of the SMART Controller. Dela time after the last detected movement The following values can be set: 3 seconds, 1,, 3, 5, 1, 15,, 3, 45 and 6 minutes and continuous (no switch-off) The off setting switches the luminaire off after the dela time has elapsed. If a time value is set, the luminaire dims to the sec. level parameter and onl switches off after the previousl set time has elapsed. The following values can be set: off, 3 seconds, 1,, 3, 5, 1, 15,, 3, 45 and 6 minutes and continuous ( never OFF function) Second light level to which luminaire dims after the dela time has elapsed. (in conjunction with the if vacant parameter) With the active setting, the lighting is automaticall switched on or off depending whether a person is present. With the inactive setting, the ILD/DSI-SMART (PTM) can, in combination with continuous time dela, onl be used for lighting control. With the off onl setting, the lighting has to be switched on manuall (momentar-action switch, remote control) but is switched off b the presence detector. With the es setting, the lighting switches off as soon as the light level exceeds 15 % of the set point for longer than 1 minutes, for instance, if the room is adequatel illuminated b sunlight. If the actual value falls below 1 % of the set point, the lighting switches back on again. With the no setting, the lighting remains switched on (at the minimum dimming level) even if the room is adequatel illuminated b sunlight and no artificial lighting is required. With the on setting, the luminaire switches on after a mains break. With the off setting, the luminaire does not switch on after a mains break. The presence detector becomes active again after 15 seconds. If the light level is manuall dimmed via a momentar-action switch or remote control, lighting control stops. The previousl set dimming level retains its fixed value as long as lighting control is not activated b manual intervention (momentar-action switch or remote control). If there is no movement in the room in this state and the time dela has elapsed, the control unit stores the fixed dimming level. With the off setting, lighting control is restarted each time movement is detected. With the on setting, the control unit switches the luminaires back to the fixed dimming level each time movement is detected and lighting control remains stopped. With this setting, lighting control can be activated again via the remote control (Automatic button). If lighting control was active before repeated detection or if the lighting was switched off manuall, the luminaires and lighting control are switched on after movement is detected in order to prevent people having to enter a dark room. With the on setting, it is possible to save the currentl set light level as a lighting control set point b pressing the momentar-action switch twice shortl. With the off setting, this function is disabled. With the DSI setting, DSI interface mode is enabled. With the LI setting, LI interface mode in which LI broadcast commands are sent is enabled. This parameter specifies how the adjustable Offset Value of the ILD behaves from channel to channel 1 over the dimming range. With the fixed setting, the previousl set Offset Value remains the same across the dimming range. (e.g. with an Offset Value of -3 %, channel remains at 7 % when channel 1 has reached 1 %). With the converging setting, the previousl set Offset Value remains the same up to a specific dimming level and decreases the closer one gets to 1%. (e.g., with an Offset Value of -3 %, the dimming level of channel is 4 % and that of channel 1 is 7 %. but both channels simultaneousl change to a dimming level of 1 % if the lighting is dimmed up). Adjustable brightness difference between channel and channel 1 of the ILD. The following values can be set: %, -1 %, - %, -3 %, -4 %, -5 %, -6 % and -7 % 1

11 luxcontrol lighting control sstem Default Parameter Motion Detector Parameter A light-level 1 time dela B sec. level if vacant 11