Undercounter Dishwasher

MPORTANT: Read and save these instructions. MPORTANT: nstaer: Leave nstaation nstructions with the homeowner, Homeowner: Keep nstaation nstructions for future reference. Save nstaation nstructions for oca inspector s use. Undercounter Dishwasher Part No, 3374368 7,/?3

Before vou start... L Proper instaation is your responsibiity. Make sure you have everything necessary for correct instaation. t is the persona responsibiity and obigation of the customer to contact a quaified instaer to assure that eectrica and pumbing instaations meet a nationa and oca codes and ordinances. Eectrica ground is required. See Eectrica requirements. DO NOT pinch power suppy cord or kink power suppy cabe between dishwasher and cabinet. DO NOT insta dishwasher over carpeted fooring. Figure 1 Proper eectrica, drain and water suppy ines must be avaiabe or must be instaed as specified within shaded area. Wiring shoud not cross in front of motor or dishwasher egs. See Eectrica, Water and Drain requirements. MPORTANT: Observe a governing codes and ordinances. Cut openings - Grommet Water ine: /2 hoe required for or arger. eectrica cabe Drain ine: - /2 hoe or power suppy or arger. cord hoe cut in Power suppy cord: 1 - /2 max. a meta hoe. cabinet. Direct wiring: 314 hoe. The unshaded area must be free of pipes or wires. Eectrica outet must be instaed in an adiacent cabinet. b- 24 odenina,\ w idth - t 33-7/a min. height Figure 2 1-24 depth + e 20.3/4 Toos and materias needed for instaation: eectric dri wire stripper and utiity knife Phiips screwdriver 5116 and /4 2 adjustabe nut driver or hex wrenches socket piers 3 twist-on wire measuring tape connectors for 16. fat-bade gauge wire (not screwdriver shown) pipe wrench 90 ebow with 3/a N.P.T. externa keyhoe saw threads on one end. tubing cutter (not The size of the other shown) end must fit your water suppy ine. pipe-joint (not shown) compound goves (not shown) Parts suppied for instaation: 2 drain hose camps. 2, No.-10 x /2 Phiips-head screws 0 drain hose Remove parts from bag. Check that a parts were suppied. Pane A Eectrica requirements L V, Corner ocation 2 min. door to cabinet or wa. - 23-718 width ) Eectrica Shock Hazard Eectrica ground is required on this appiance. f cod water pipe is interrupted by pastic, non-metaic gaskets or other insuating materias Do Not use for grounding. Do Not ground to gas pipe.. Do Not modify the power suppy cord pug. f it does not fit the outet, have a proper outet instaed by a quaified eectrician. Do Not use an extension cord with this appiance. Do Not have a fuse in the neutra or grounding circuit. A fuse in the neutra or grounding circuit coud resut in an eectrica shock. Check with a quaified eectrician if you are in doubt as to whether the appiance is propery grounded. Faiure to foow these instructions coud resut in serious injury or death. 4 min. rderside :ounter ieight. f codes permit and a separate grounding wire is used, it is recommended that a quaified eectrician determine that the grounding path is adequate. A 120-vot, 60.Hz, AC-ony, 15 or 20- ampere, fused eectrica suppy is required. Time-deay fuse or circuit breaker is recommended. t is recommended that a separate circuit serving ony this appiance be provided. The dishwasher must be connected copper wire ony. with Check ocation where dishwasher wi be instaed. The ocation shoud provide: Easy access to water, eectricity and drainage ines. Convenient oading -the best position is eft or right of kitchen sink. Opening that is square for proper dishwasher operation and appearance. Cabinet front that is perpendicuar to foor. Protection so that water inet vave and drain cannot freeze. /4 minimum cearance between motor and fooring to prevent motor from overheating. Eectrica Shock Hazard t is the persona responsibiity and obigation of the customer to contact a quaified eectrician to assure that the eectrica instaation is adequate and is in conformance with the Nationa Eectrica Code, ANS/NFPA 70 - atest edition* and a oca codes and ordinances. Faiure to foow these instructions coud resut in eectrica shock or other persona injury. Eectrica wiring and components must not contact any pumbing materia or drain hose.. Cabinet opening must competey encose sides, top and back of dishwasher. Faiure to do so may resut in persona injury from exposed wiring. Persona njury/product Damage Hazard Avoid opening dishwasher door before dishwasher is instaed. Dishwasher, before it is instaed, may tip over when door is opened, resuting in persona injury or product damaae. Copies of the standards isted may be obtained from: *Nationa Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269 Read and foow the Eectrica requirements, Water requirements and Drain requirements sections before instaing dishwasher. Wiring methods Pick one method to foow, depending upon your dishwasher and oca codes. A Direct wire method (cdbe connecting dishwasher to a junction box). Eectrica Shock Hazard Disconnect eectrica power at the service pane (fuse box or circuit breaker box). Faiure to do so coud resut in serious injury or death. Recommended grounding method - 1. Disconnect power suppy. 2. Run fexibe, armored or non-metaic sheathed, copper cabe (with grounding wire) from fused disconnect, circuit breaker or junction box through the 3/4 cabinet hoe to the dishwasher ocation. The cabe must extend 24 from the back wa. The hoe cut through a wood cabinet shoud be sanded unti smooth. The hoe cut through a meta cabinet must be covered with a grommet (Part No. 302797), avaiabe from your oca deaer or parts suppier. A U.L.-isted strain reief or conduit connector must be instaed at each end of the power suppy cabe (at the dishwasher and at the junction box). Wire sizes (COPPER WRE ONLY) must conform with the rating of the dishwasher.

stud Figure 3 grounding wire 1 U.L.-isted strain reief or conduit connector - power suppy cabe 3. Remove the dishwasher termina box cover. Connect the white and back wires of the power suppy cabe to the white and back eads in the termina box with twist-on wire connectors. (See Figure 3.) 4. Loosen the front nut on..:...:. the grounding. :.:. connection stud ocated.i!., on the back of the termina box. Do Not oosen the rear nut on the 2i U-S! Yeped : grounding connection stud. Form the bare ~ grounding wire into a U-shaped hook. Wrap the grounding wire hook around the grounding connection stud between the two nuts on the stud. Securey tighten the front nut over the grounding wire. 5. Check that strain reief or conduit connector screws are tight. Repace termina box cover. B. Power suppy cord method (connecting dishwasher to outet). Loca codes may permit the use of a U.L.- isted, fexibe, three-conductor, power suppy cord terminated with a threeprong, grounding-type pug. t is recommended that cord kit (Part No. 43 17824). avaiabe at your oca deaer or parts suppier, be used. Foow the instructions packaged with the power suppy cord kit. f the cord kit is not avaiabe ocay, the fexibe cord used must be a U.L.-isted, three-conductor, 16-gauge cord that meets the Nationa Eectrica Code, ANS/NFPA 70 - atest edition* and oca codes and ordinances. The ength of the cord must not exceed six feet. t must be routed so it does not touch the dishwasher motor or the ower portion of the dishwasher tub. A strain reief (Part No. 596171), avaiabe at your oca deaer or parts suppier, or a simiar part must be used to secure the fexibe cord to the dishwasher frame or termina box. The fexibe cord must be pugged into a mating, 3-prong, grounding-type wa receptace, grounded in accordance with the Nationa Eectrica Code ANS/NFPA 70 - atest edition,* and a oca codes and ordinances. Foow the instructions packaged with the fexibe cord. Regrdmended 3-prong, J-prong, groundingtvoe wa receptace grounding For your persona safety, this appiance must be grounded. A power suppy cord having a 3-prong grounding pug must be used. t is the persona responsibiity and obigation of the customer to have a propery grounded, 3-prong wa receptace instaed by a quaified eectrician. The receptace shoud be instaed on the rear or side wa of the cabinet next to the dishwasher opening. Pane B Water reauirements The hot water ine to the dishwasher must provide between 15-120 psi water pressure. The hot water heater shoud be set to deiver 140 F water temperature to the dishwasher for best resuts. Use 3/8 minimum O.D. copper tubing or /2 minimum pastic tubing inet ine. Dishwasher inet vave has 3/8 N.P.T. interna pipe thread. Drain requirements The drain hose MUST have a high drain oop, 20 minimum ABOVE FLOOR, to prevent backfow or water siphoning out of dishwasher during operation. NOTE: An air gap MUST BE USED in the high drain oop if the drain hose is connected to house pumbing ower than 20 above the foor. Drain hose, suppied, meets AHAM DW- 1 test standards. Cut 1- /2 hoe in cabinet wa for drain hose. Additiona drain ine (a minimum of /2.D. and no onger than 20 feet) can be used if needed. Now start... With dishwasher in kitchen. 1 cabine]- 4 Aternate waterine ocations water suppy pipe / 1 n Rough in water ine to the dishwasher cabinet opening using one of the routing methods shown. Cut /2 or arger hoe in cabinet wa for water ine. 2 n nsta a shutoff vave in the water ine where it can be easiy used. 3 n Fush water ine into a bucket to get rid of any partices that may cog inet vave. Turn shutoff vave to the OFF position. Eectrica Shock Hazard Disconnect eectrica power at the service pane (fuse box or circuit breaker box). Faiure to do so coud resut in eectrica shock or other persona ~ iniurv. eectrica wiring aternate eectrica wiring ocation \ R -- 4 H Cut a 1- /2 maximum hoe for power suppy cord or a 3/4 hoe for direct wiring in the cabinet or foor for the eectrica wiring to pass through. f this hoe is cut in a wood cabinet, sand the hoe unti it is smooth. f the hoe is cut in a meta cabinet, the hoe must be covered by a grommet (Part No. 302797), avaiabe at your oca deaer or parts suppier. nsta wa receptace on rear or side wa of a cabinet next to dishwasher opening. nsta a 3/4 U. L.-isted conduit connector to connect the fexibe armored or non-metaic sheathed, copper cabe (with grounding wire> to the fused disconnect, circuit breaker or junction box. Run the cabe through the hoe in the cabinet opening. The cabe shoud extend 24 from the back wa.

Recommended drain hose connection methods: Drain hose to air gap to waste tee. air-gap kit (Part No. 300096) w Remove the 4 screws attaching access pane and toe pane to dishwasher using a /4 hex socket, nut driver or Phiips screwdriver. Remove access pane and toe pane. 8 w Latch dishwasher door. Push dishwasher into pace, siding drain hose through hoe cut in cabinet opening. Do not pinch power suppy cord or kink power suppy cabe between dishwasher and cabinet. Check that front eveing egs are firmy against the foor. Aign dishwasher door with cabinet doors, so that spacing is the same on both sides. waste tee L 20 minimum cearance to foor k i camps Entry must be above trap. Drain hose to air gap to disposer 0 air-gap kit (Part No. 6 n Measure heiaht of cabinet 9 n Connect drain hose to an air gap opening from the 6ont edge of the underside of cabinet opening to foor. Check chart for that height opening. Put the whees in the required position. The dishwasher shoud be instaed as eve as possibe from front to back. Loosen and then turn front eveers the number of times indicated in the chart or waste tee using one of the recommended or aternate methods. Cut hose connector to fit. if needed. r 34! 1! 9 For additiona height: 1. Add shims under the whees. 2. Turn front eveers (each turn is approximatey 1 /16 in height). You may have this type drain connector... f connecting drain hose to an air gap or waste tee, cut end of drain hose as shown. Secure drain hose with screw-type or spring-type hose camp (camp type varies with modes). Do Not cut drain hose when connecting to a 7/8 disposer connector. Knock out pug from disposer inet. Secure drain hose with hose camp provided. DO NOT cut ribbed section to shorten drain hose. Numbers correspond to steps. to foor Entry mui be above trap. nsta air gap according to kit instructions. f other brands of air gaps are used, they shoud be checked to make sure they aow for the same air fow. Connect the air gap to a waste tee* or disposer using a rubber connector*. Most disposers have 7/8 connectors or specia connectors are avaiabe at pumbing suppy houses. Knock out disposer inet pug from inet. f inet pug fas inside disposer, you must remove inet pug before connecting drain hose. f disposer is aready instaed in sink, you may need to take out disposer to remove inet pug. or this type. \ -- / straight. 7 n Put spring-type drain hose camp over connector. Push drain hose onto connector. Use piers to open camp and side camp over drain hose and connector. Check that drain hose is secure. f screw-type camp is used instead of spring-type camp, use a 5/16 nut driver to tighten drain hose securey to connector. To minimize noise and vibration, route drain hose to avoid contact with door springs, motor, water ine, cabinet or fooring. Do Not run drain hose over top of tub. Connect to garbagedisposer connector. Cut here to connect to waste tee or /2 copper tu,birig-. Drain hose Y r traight end Pane C

Aternate drain hose TOP mountina brackets attached connection methods: 17 w Check that a parts have Drain hose to waste tee. waste tee * 20 minimum cearance to foor,~~n~e~o 10 x /2 N Do Not drop screws into tub. L been instaed and no steps were skipped. Check that you have a the toos you started with. 18 n Turn on eectric subpv. Start dishwasher and aow it to compete a cyce. Check that dishwasher is working propery and that there are no water eaks. f oca pumbing codes permit, dishwasher drain hose may be connected directy to waste tee. The waste tee connection MUST be made ahead of the trap and a minimum of 20 inches above the foor. w Ooen dishwasher door and Drain hose to disposer. d remove a shipping materias. Remove bottom rack. Pace a newspaper, arge sheet of paper or a towe over bottom of dishwasher to prevent screws or other ut hose items from entering the pump area 19 w Rebace the access bane1 ctor. when securing dishwasher to and toe pane. The toe pane must be countertop. positioned to contact foor. 20 minimum cearance to 20 w f changing coor of door foor! and access pane or instaing custom panes, foow the To change door Persona njury/product Damage pane coor and To change access Hazard pane coor instructions, Pane E and f oca pumbing codes permit, The dishwasher must be secured to back cover. dishwasher drain hose may be the countertop to keep it from titing when door is open. connected directy to disposer. Most disposers have 7/8 connectors or Do Not drop screws in dishwasher specia connectors are avaiabe at tub. f screws shoud fa into pump, pumbing suppy houses. pump and motor damage may occur. Faiure to foow these instructions may resut in persona injury or product damage. Knock out disposer inet pug from inet. f inet pug fas inside disposer, you must remove inet pug before connecting drain hose. f dispose is aready instaed in sink, you may need to out disposer to remove inet pug. A parts are avaiabe through your deaer or oca hardware or pumbing store. Product Damage Do Not soder within 6 of pastic water inet vaves. Faiure to foow this instruction coud resut in product damage. 13 w Secure dishwasher to countertop with two, No.- 10 x /2 Phiips-head screws from parts bag. You MUST secure dishwasher to keep it from titing when door is opened or cosed. Do Not drop screws in dishwasher tub. Remove paper from bottom of dishwasher. Equay spaced Congratuations! You have just finished instaing your new undercounter dishwasher. Keep instaation nstfuctions avaiabe for easy reference. water inet vave \ \ 14 w Open door approximatey 3 and check for equa spacing between inner door and tub sides. f necessary, oosen screws that fasten dishwasher to countertop and shift tub. Tighten screws. 10 n Connect water pipe or tubing directy to water inet vave. Do Not run pipe or tubing across front of motor or dishwasher egs. Turn on water suppy and check for eaks. 11 n Check eectrica requirements. Be sure you have correct eectrica suppy and recommended grounding method. See Panes A and B for proper connection. 15 n Check door for prober operation. Door shoud cose easiy without samming and open with its own weight. f necessary, cose door and adjust both door springs by moving spring ends to different hoes in base. 16 w Take a few minutes to read the Use and Care Guide to fuy understand your new dishwasher. Pane D

To change door pane coor NOTE: The opposite side of the door coor pane is a different coor. Persona njury Hazard Wear goves and hande panes carefuy. Cut meta edges may cause persona injury or damage to other materias. 1 n nsert finger under one end of retainer and pu towards you in a peeing action. Set retainer aside. m Lift /w door pane(s) at outer edges. Use one hand to bow bottom of pane(s). Remove pane(s). Do Not remove spacer. To change access coor pane (For modes so equipped) Persona njury Hazard Wear goves and hande panes carefuy. Cut meta edges may cause persona iniury or damage to other materias. 1 n Push up with thumbs on each end of access pane top trim to unsnap trim. Remove top trim and set it aside. 2 n Carefuy side coor access pane upwards and remove. Do Not remove spacer. 3 w With desired coor facing out, bow access pane and insert into >ttom dge Figure 4 Cut door pa cear access pane when door is in open position. This pane is narrower than access pane. Fie or sand edges of patoy sivers. Heavy-duty door springs must be used if custom door pane weighs more than 4 pounds. Heavy-duty Door Springs Kit, Part No. 43 18050, is avaiabe from your deaer or parts suppier. Maximum door weight is 8 pounds. Wood access pane This pane is wider that door pane. b- 23-5116 4-711 access bane1 frame. Side pane down into groove aong bottom of access pane frame. with desired coor facing out, into one side of door 4 n Line up frame. edges of top trim with sides of access pane frame. Tit back of Bow door 4 n pane(s) and insert other side of door pane(s) into door frame. contro consoe Push in 5 n on door pane(s) near the top and side pane(s) and spacer up inside bottom of contro consoe, aowing pane(s) to rest on channe at bottom of door. trim down and side into pace. Snap front of trim down to cover top edge of access pane. To insta customized wood panes in door and access pane Dishwasher door pane and access pane (if mode is so equipped) can be customized to match wood cabinets. A standard /4 (7/32 actua thickness) wood pane can be used as is for customizing the door and access panescabinet- maker cut the A door pane thicker than 7/32, requires routing the top and bottom to a 7132 thickness. An access pane thicker than 7/32, requires routing a four edges to a 7/32. t is recommended that a cabinetmaker cut the customized panes because of the precise cuts required. (See Figures 5 and 6.) Wood door pane Cut accuratey for a snug fit between door side frames. Note: Custom pane fits between, Not inside frame. A edges routed to 7/32 thickness. Top view,7/32 thick /4 min. n Cut wood door and access panes using specified dimensions. Make sure wood grain direction matches cabinet wood grain. 2 w Fie or sand edges of wood panes to avoid sivers. - Dishwasher is subject to some humidity. Cover both sides and edges of wood panes with moisture-resistant seaer. Persona njury Hazard Wear goves and hande panes carefuy. Cut meta edges may cause persona injury or damage to other materias. 3 w nsert finger under one end of retainer and pu towards you in a peeing action. Set retainer aside. 4 Lift door n pane(s) at outer edges. Use one hand to bow bottom of pane(s). Remove pane(s) and spacer. Save pane(s) and spacer for future use. top of pane under contro consoe 6 Snap one end of retainer into n channe as shown. Push inward whie siding thumb aong fu ength of retainer. Pane E w nsert top of wood door pane between sides of door frame about 3 beow consoe. Rotate wood door pane down against dishwasher door. Side top edge of wood door pane under bottom edge of consoe. Press ower portion of wood door pane in pace between sides of door frame, aowing wood door pane to rest on channe at bottom of door.

Snap into Push in 6 Snap one end of%tainer into n channe as shown. Push inward whie siding thumb aong fu ength of retainer. 7 n Check door for proper operation. Door shoud cose easiy without samming and open with its own weight. f necessary, cose door and adjust both door springs by moving spring ends to different hoes in base, 8 n Push up with thumbs on each end of access pane top trim to unsnap trim. Remove top trim and set it aside. 9 w Carefuy side coor access pane and spacer upwards and remove. Save coor access pane and spacer for future use. 10 n nsert wood access pane into access pane frame. Side.pane down into groove aong bottom of access pane frame. t may be necessary to remove the two screws securing top of access pane to dishwasher frame and tit access pane forward to insta some wood panes. 11 n Line up edges of top trim with sides of access pane frame. Tit back of trim down and side into pace. Snap front of trim down to cover top edge of wood access pane. f the dfshwasher is not operating propery... Check these points: s the door cosed tighty and atched securey? Has the cyce been set correcty to start the dishwasher? s the water turned on? Has a house fuse bown or circuit breaker tripped? Has eectrica power been interrupted? Note: f the motor has stopped because of overoad, it wi automaticay reset itsef within a few minutes. f after checking these points the dishwasher sti does not run or compete a cyce, ca for service. f you need assistance... Check your Use and Care Guide for a to-free number to ca or ca the deaer from whom you purchased this appiance. When you ca, you wi need the dishwasher mode and seria number. Both numbers are ocated on the seria/rating pate ocated behind the door on the front frame of the dishwasher opening. Part No. 33774368 01993 Benton Harbor, M 49022 Printed in U.S.A.