FF0002 Certificate of Compliance Certificate: 2792948 Issued to: Siemens Canada Limited 1954 Technology Drive Peterborough, ON K9J 7B1 Canada Attention: Mr. Lee Rogers The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only K Atkins Issued by: K. Atkins PRODUCTS CLASS 2252 06 - PROCESS CONTROL EQUIPMENT CLASS 2252 86 - PROCESS CONTROL EQUIPMENT (Certified to U.S. Standards) External Display and Adjustment Unit, Model LGRI; supplied from SIEMENS sensor only, optional heating, supplied at 24Vdc (+5%), 1.7 W; Enclosure CSA type 4X, 6P; Ambient Temperature -40 C to +80 C (without display and adjustment module), -15 C to +70 C (with display and adjustment module), -40 C to +70 C (with heated display and adjustment module); Notes: 1. To be supplied by a Class 2 or Limited Energy Source in accordance with CSA 61010-1-12. 2. Rated: Pollution Degree 2, Overvoltage Category I. 3. Environmental Conditions: 5000 m max DQD 507 Rev. 2012-05-22 Page 1
CLASS 2258 02 - PROCESS CONTROL EQUIPMENT For Hazardous Locations CLASS 2258 82 - PROCESS CONTROL EQUIPMENT For Hazardous Locations Certified to US Standards Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups E, F and G; Class III Class I, Zone 2 A/Ex na IIC Gc Model LGRI series Indication and Adjustment Unit; supplied from SIEMENS sensor only, optional heating, supplied at 24Vdc (+5%), 1.7 W; Enclosure CSA type 4X, 6P; Ambient Temperature -40 C to +80 C (without display and adjustment module), -15 C to +70 C (with display and adjustment module), -40 C to +70 C (with heated display and adjustment module); Permissible temperature -20 C... + 53C -40 C... + 68 C -40 C... + 85 C Model LGRI.CAIabcdef, where: a = Housing: K, A or V b = Protection: I or N c = Cable entry: M, N or D d = Indicating adjusting module: X, A or H e = Mounting: A, C, D, E or F f = Certificates: X or M Class I, Division 1, Groups A, B, C and D; Class II, Division 1, Groups E, F, G; Class III Ex d IIC Gb Class I, Zone 1 A/Ex d IIC Gb Model LGRI series Indication and Adjustment Unit. Enclosure Type 4X; IP66. Permissible temperature -50 C... + 60 C -40 C... + 68 C -40 C... + 85 C Model LGRI.CEIabcdef, where : a = Housing: A or V b = Protection: N c = Cable entry: M, N or D d = Indicating adjusting module: X or A e = Mounting: A, C, D, E or F f = Certificates: X or M DQD 507 Rev. 2012-05-22 Page 2
CLASS 2258 04 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe, Entity - For Hazardous Locations CLASS 2258 84 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe, Entity - For Hazardous Locations Certified to US Standards Class I, Division 1, Groups A, B, C and D; Class II, Division 1, Groups E, F, G; Class III Ex ia IIC Ga, Gb Class I, Zone 0 A/Ex ia IIC T6 Ta = 60 C Model LGRI series Indication and Adjustment Unit. Enclosure Type 4X, IP66. Intrinsically safe with entity parameters Vmax = 6.4 V, Imax = 207.5 ma, Pi = 332 mw, Ci = 0 µf, Li = 0 when connected to the Comm Port of a SIEMENS sensor per control drawing 49633. EPL Ga installation: Permissible temperature -20 C... + 37C -20 C... + 50 C -20 C... + 60 C EPL Gb installation: Permissible temperature -40 C... + 53C -40 C... + 68 C -40 C... + 85 C Model LGRI. CaIbcdefg where a = Approval: C or O b = Housing: K, A or V c = Protection: I or N d = Cable entry: M, N or D e = Indicating adjustment module: X or A f = Mounting: A, C, D, E or F g = Certificates: X or M APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No. 61010-1-12 UL Std. No. 61010-1 (3 rd Edition) CSA Std. C22.2 No. 94-M91(R 2006) CSA Std. C22.2 No. 25-1966 (R2009) - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use, Part 1: General Requirements - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use - Part 1: General Requirements - Special Purpose Enclosures - Enclosures for Use in Class II Groups E, F and G Hazardous DQD 507 Rev. 2012-05-22 Page 3
Locations CSA Std. C22.2 No. 30 M1986 (R 2003) - Explosion-Proof Enclosures for Use in Class Hazardous Locations CSA Std. C22.2 No. 157-92 (R 2006) - Intrinsically Safe and Non-Incendive Equipment for Use in Hazardous Locations CSA Std C22.2 No. 213-M1987 (R 2004) - Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations CAN/CSA Std. C22.2 No. 60079-0:12 - Electrical apparatus for explosive gas atmospheres - Part 0: General requirements CAN/CSA Std. C22.2 No. 60079-1:12 - Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof Enclosure d CAN/CSA Std. C22.2 No. 60079-11:12 - Electrical apparatus for explosive gas atmospheres - Part 11: Intrinsic safety "i" CAN/CSA Std. C22.2 No. 60079-15:12 - Electrical Apparatus for Explosive Gas Atmospheres--Part 15: Type of Protection "n" UL Std. No. 913 (4th Ed) - Intrinsically Safe and Associated Apparatus For Use In Class I, II, and III, Division 1, Hazardous (Classified) Locations ANSI/ISA 12.12.01 - Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Division 1 and 2 Hazardous (Classified) Locations UL Std. No. 50 (Edition 10) - Enclosures for Electrical Equipment UL Std. No. 1203, Ed 4 (2006) - Explosion-Proof and Dust-Ignition-ProofElectrical Equipment for Use in Hazardous (Classified) Locations ANSI/UL 60079-0 (5th Ed. 2009) - Explosive Atmospheres Part 0: Equipment - General Requirements ANSI/UL 60079-1 (6th Ed. 2009) - Explosive Atmospheres Part 1: Equipment Protection by Flameproof Enclosures d ANSI/UL 60079-11(5th Ed. 2009) - Explosive Atmospheres Part 11: Equipment Protection by Intrinsic Safety "i" ANSI/ISA 60079-15 (5th Ed. 2009) - Electrical Apparatus for Explosive Atmospheres: Part 15: Electrical Apparatus with Type of Protection n MARKINGS The manufacturer is required to apply the following markings: Products shall be marked with the markings specified by the particular product standard. Products certified for Canada shall have all Caution and Warning markings in both English and French. DQD 507 Rev. 2012-05-22 Page 4
Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where applicable, in accordance with the requirements of those authorities. The products listed are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US (indicating that products have been manufactured to the requirements of both Canadian and U.S. Standards) or with adjacent indicator 'US' for US only or without either indicator for Canada only. (1) Company's name, trademark, or the CSA Master Contract Number (adjacent the CSA Mark). (2) Catalogue / Model designation. (3) Complete electrical rating (amps, hertz, and volts). (4) Date code / Serial number traceable to month and year of manufacture. (5) Hazardous Location designations. (6) Optional markings: Class I, Zone 0/1, IIC, T6-1 (as applicable) (7) The symbol "A/Ex ia" (as applicable) (8) The words "INTRINSICALLY SAFE" (as applicable) (9) Install as per Installation Control Drawings (as applicable) (10) Temperature code with derating for process temperature (may appear in Instruction Manual or in Safety Manual provided with the Instruction Manual. (11) Maximum ambient 60 C (12) Maximum Working Pressure (13) CSA Mark, with the C/US indicator; The products listed are eligible to bear the CSA Mark with adjacent indicators 'C' and 'US' for Canada and US. (14) Single Seal (15) The following cautions: WARNING - A SEAL SHALL BE INSTALLED WITHIN 18 inch OF THE ENCLOSURE WARNING - DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE IS PRESENT WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR INTRINSIC SAFETY WARNING AVOID ELECTROSTATIC CHARGE REQUIRED METHOD OF MARKING: The marking shall be permanent, such as a 0.5-mm thick metal nameplate secured by drive pins or screws in bottomed holes, cast, etched, or engraved, or CSA Accepted adhesive-type nameplates, manufactured by Brady, P/N B-423 or Schreiner Colour Laser Film Black SA (39-06), P/N Polyscript Carbo ACE SA, mounted to bare stainless steel, Valox 357 Polymer or painted aluminum. The manufacturer is required to apply the following markings: Products shall be marked with the markings specified by the particular product standard. Products certified for Canada shall have all Caution and Warning markings in both English and French. Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where applicable, in accordance with the requirements of those authorities. DQD 507 Rev. 2012-05-22 Page 5
The following markings appear on the product: 1. Company s identification (company name and/or Master Contract and/or registered trade name); 2. Marking on the unit that indicates the manufacturing location if the equipment is manufactured at more than one factory location.model designation; 3. Electrical rating; 4. Date of manufacture: Month and year of manufacture or date code. If a serial number is used instead of date of manufacture, a record of serial numbers shall be kept traceable to date of manufacture. (Not related to date of sale). 5. The products listed are eligible to bear the CSA Mark shown with adjacent indicators C and US for Canada and US, or with adjacent indicator US for US only, or without either indicator for Canada only:, or, or. Marking Method: The above markings are made via silk screening, die stamping, moulding, or on CSA certified or UL recognized adhesive nameplate material compatible with the surface used, or other equivalent permanent means that can pass the label rub test. DOCUMENTATION: Equipment is accompanied by the following documentation. General: Technical specifications, instructions for use and details of where technical assistance may be obtained if required. Equipment Ratings: This includes equipment supply, description of I/O connections and operating environmental conditions. 1. Pollution degree 2; 2. Installation category I; 3. Altitude 5000m; 4. Electrical supply from SIEMENS sensor only, optional heating, supplied at 24Vdc (+5%), 1.7 W 5. Temperature -40 C to +80 C (without display and adjustment module), -15 C to +70 C (with display and adjustment module), -40 C to +70 C (with heated display and adjustment module; Equipment Installation: This includes instructions for Assembly and mounting; location requirements. PERMANENTLY CONNECTED EQUIPMENT requires the special considerations to satisfy the CEC, NEC and the Canadian deviations in the standard, including overcurrent and fault protection as required. DQD 507 Rev. 2012-05-22 Page 6
Equipment Operation: This includes explanations of operating controls and warning symbols used. 1. List of accessories which meet the manufacturer s specifications to be used; 2. Guidance on how to determine that the equipment is functioning correctly; 3. Statement that, if the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. Equipment Maintenance and Service: This includes instructions for preventative maintenance, inspection and cleaning, replacement of parts, etc. DQD 507 Rev. 2012-05-22 Page 7