MECHANICAL ADDENDUM # DAE: March 4, 208 PROJEC NO: 7574 PROJEC: Orchard Cove Renovation DIISION 22 & 23 DRAWINGS SHEE - MG-00 Basement Level Medical Gas. Emergency oxygen supply connection was added and the associated keynote. SHEE - MP-0 Attic Mechanical Piping Plan. Keyed note #2 has been removed from this sheet. Fire-rated access doors are not required for each A box. he A boxes will be accessed/maintained through the attic access. 2. hey leaders & symbols for keyed notes 3 & 4 have been moved so they point to the correct locations near the north exterior of the building. SHEE - MP-40 Enlarged Mechanical Piping Plans. his sheet is no longer required and can be ignored. SHEE - P-0 Level Plumbing Plan. Pipe size of DHW and DCW increased to. 2. DHWR return loop added. SHEE - P-40 Enlarged Plumbing Plans. Detail - Roll-in Shower & Exam Rm Enlarged Plumbing Plan A. Keyed note #2 has been added to Exam Room 2-A, Roll-In Shower 24, & Existing Activity Space 20. 2. Keyed note #2 has been added to this sheet. 3. Automatic Fire Sprinklers and Piping General Notes have been added to this sheet. 4. Pipe size of DHW and DCW increased to. 5. DHWR return loop added. 6. Pressure callout was realigned. SHEE - P-50 Plumbing Details. Emergency oxygen supply connection detail added. 2. Detail title scale description adjusted.
Page 2 of 3 SPECIFICAIONS SECION - Specification Index. his index has been updated to include sections 2000, 23528, & 33633. It has also been updated to no longer show section 235239. SECION - 2000 Water-Based Fire-Suppression Systems. his section has been added to the mechanical specifications. SECION - 23528 Flexible Steel Water-ube Boilers. his section has been added to the mechanical specifications. SECION - 235239 Fire-ube Boilers. his section is no longer required and has been removed from the mechanical specifications. SECION - 33633 Underground Hot Water Piping System. his section has been added to the mechanical specifications. PRIOR APPROALS he following manufacturers, trade names and products are allowed to bid on a name brand only basis with the provision that they completely satisfy all and every requirement of the drawings, specifications and all addenda shall conform to the design, quality and standards specified, established and required for the complete and satisfactory installation and performance of the building and all its respective parts. Item Manufacturer Comments Boilers Pumps Domestic Heat Exchanger Access Doors Louvers Centrifugal Roof entilators Duct Silencers Split System A/C Units Air Separators Expansion anks Boiler Flue Building Automation Controls Phenolic Foam Ducts Fulton, Lochinvar Wilo, PACO, Grundfos Kelvion Nailor, Kees Nailor, American Warming, Cesco, Greenheck ACME, Greenheck Price LG, Lennox, Daikin Spirotherm Wessels, Flexcon an Packer, Industrial Chimney Company Wasatch Controls, Controls Solutions Group PALDuct Fire, Smoke, Combination Dampers Cesco High Efficiency ake-off Fittings Manual olume Dampers Control Dampers ariable Frequency Drives Clifco Air-Rite Greenheck Danfoss
Page 3 of 3 Underground Duct Manufactured Casings Electric Radiant Heaters Hydronic Heating & Cooling Panels Hydronic Air Coils Humidifiers Monoxivent Commercial Acoustics Indeeco Sigma emtrol Neptronic
GENERAL NOES # KEYED NOES. PROIDE LINK-SEAL IN ANNULAR SPACE, YPICAL. 2. PROIDE SCHEDULE 80 PC SLEEE HROUGH FOUNDAION WALL, YPICAL.. SEE SHEE MG-40 FOR CONINUAION. 2. UNDERGROUND MED GAS PIPING IS O BE ENCLOSED IN A CONINUOUS CONDUI AND RACER PIPE. 8. PROIDE 45 DEGREE FIINGS O MAKE ERICAL CHANGE IN PIPE ROUING. REMOE SUFFICIEN BUILDING FOUNDAION AND SLAB O ALLOW FOR CONDUIS AND PIPING O ENER INSIDE BUILDING. " MA UP 2" AC UP " O2 UP 3. PROIDE FERNCO RANSIION COUPLING, YPICAL. 4. PROIDE 4" ADS CONINUOUS CORRUGAED CASING, YPICAL. 5. UPON ENRY INO MECHANICAL ROOM RUN PIPING OERHEAD. 6. FLOOR SLEEE O BE PROIDED FOR NEW PIPING. 3. SAW CU EXISING ASPHAL FOR NEW PIPING. REPAIR AND REPLACE WIH ROAD BASE AND ASPHAL O MACH EXISING. YPICAL. 4. " O (OXYGEN), 2" AC (ACUUM), AND " MA (MEDICAL AIR) INSALLED IN SEPARAE 4" SLEEES. 5. PROIDE 45 DEGREE FIINGS O ALL FOR SLEEE O SLIDE OER AND PAS FIING. 6. REPLACE CONCREE CURB O MACH EXISING. REMOE CONCREE O NEARES JOIN. REPLACE WIH FULL PANELS OF CONCREE. 7. PRESERE AND PROEC EXISING CURB AND GUER. 9. CORE DRILL FOUNDAION WALL. 0. EXISING 3 ON CONDENSER UNIS AND MECH EQUIPMEN ON CONCREE PADS.. EXISING ELECRICAL O REMAIN. HIGH OLAGE ELECRICAL CONDUI ON EXERNAL FACE OF BUILDING. ERIFY EXAC UNDERGROUND LOCAIONS WIH UILIY LOCAER SERICE. 2. EXISING REE/BUSHES O BE PRESERED. 3. GUER SYSEM O BE PRESERED. 4. REFER O SHEE P-50 FOR EMERGENCY OXYGEN SUPPLY CONNECION DEAIL. ELLIO WORKGROUP ARCHIECURE LLC 44 West Ute Blvd, Suite 00 Park City, Utah 84098 435-649-0092 or 80-45-839 elliottworkgroup.com 5 3 N3 MA AC O2 " 2" " 2 4 N4 N5 2 0 3 MA 2 S3 S4 S5 REGISERED SAE PROFESSIONAL No. 87737 JEFFREY S. WAKINS 04.20.208 OF UAH ENGINEER SOUH DAIS COMMUNIY HOSPIAL N6 N7 7 6 8 9 4 " MA UP 2" AC UP " O2 UP DHX " MA UP 2" AC UP " O2 UP S6 Orchard Cove Renovation 485 E 500 S Bountiful, U 8400 YY No. Date Description 5/4/8 ADDENDUM # ZZ AA AA W W2 W3 W4 W5 W6 W7 W8 W9 ISSUE DAE: 208.04.20 OWNER PROJEC NO:. CONRAC NO:. DRAWN BY: CHECKED BY: DESIGNED BY: EWG PROJEC NO: COPYRIGH: Author JSW KJM 207.60 Elliott Workgroup Architecture, LLC SHEE ILE BASEMEN LEEL MEDICAL GAS PLAN SCALE: /8" = '-0" W W W. B F A. C O M 330 South 300 East AN BOERUM & FRANKASSOCIAES, INC. CONSULING ENGINEERS Salt Lake City Logan St. George empe Salt Lake City, U 84 BFA Project Number: 7574 80.530.348 80.530.350 F BASEMEN LEEL MEDICAL GAS MG-00 SHEE OF
# KEYED NOES. HIS HEAING HO WAER SUPPLY AND REURN PIPING IS O RUN BELOW GRADE FROM HE NEW BOILER SHED O HE MECHANICAL ROOM ON HE LOWER LEEL. SEE SHEE MP-00 FOR CONINUAION. 2. HIS KEYED NOE IS NO USED. 3. HIS HEAING HO WAER SUPPLY AND REURN PIPING IS O RUN BELOW GRADE FROM HE NEW MAIN PIPING OER O HE NEW AIR HANDLER LOCAED ON GRADE. 4. ALL EXPOSED PIPING IS O BE LINED WIH HEA RACE A 5 WAS PER LINEAR FOO. E E2 E3 E4 E5 E6 E7 E8 E9 E0 E E2 E3 ELLIO WORKGROUP ARCHIECURE LLC 44 West Ute Blvd, Suite 00 Park City, Utah 84098 435-649-0092 or 80-45-839 elliottworkgroup.com 4 2 /2" HWR 3 M-40 AHU H 2 /2" HWS XX AAA BBB N N2 N3 N4 N5 N6 N7 YY 4 3 /4" HWR 2/2" HWS " HWR 3/4" HWR 2/2" HWS 2/2" HWR 3/4" HWS 2 /2" HWS -3-4 -5-9 -6-7 -2 S S2 S3 S4 S5-8 2/2" HWS DN 2/2" HWR DN S6 /4" HWR /4" HWR /2" HWR /2" HWR 2" HWR 2/2" HWS 2" HWS 2" HWS - -0-34 3/4" HWS 3/4" HWR -9-8 -7-6 -5-4 -3-32 -2-33 - 2" HWR 2" HWS 2" HWR 2" HWS 2" HWR 2" HWS /2" HWS REGISERED PROFESSIONAL No. 87737 JEFFREY S. WAKINS 04.20.208 SAE OF UAH ENGINEER SOUH DAIS COMMUNIY HOSPIAL Orchard Cove Renovation 485 E 500 S Bountiful, U 8400 No. Date Description 5/4/8 ADDENDUM # -20-2 -22-23 -24-25 -26-27 -28-29 -30-3 AIC MECHANICAL PIPING PLAN SCALE: 3/32" = '-0" ZZ AA 2 /2" HWR 3/4" HWS " HWS " HWS /4" HWS 2 /2" HWR AA W W2 W3 W4 W5 W6 W7 /4" HWS /2" HWS 2 /2" HWR 2" HWR /2" HWS 2" HWR W8 W9 W0 W W2 W3 BB AN BOERUM & FRANKASSOCIAES, INC. ISSUE DAE: 208.04.20 OWNER PROJEC NO:. CONRAC NO:. DRAWN BY: CHECKED BY: DESIGNED BY: EWG PROJEC NO: COPYRIGH: KJM JSW KJM 207.60 Elliott Workgroup Architecture, LLC SHEE ILE AIC MECHANICAL PIPING PLAN CONSULING ENGINEERS W W W. B F A. C O M Salt Lake City Logan St. George empe 330 South 300 East Salt Lake City, U 84 BFA Project Number: 7574 80.530.348 80.530.350 F MP-0 SHEE OF
# KEYED NOES. PLUMBING O BE IED INO EXISING LAAORY SUPPLIES ON OPPOSIE SIDE OF WALL. SEE P-40, YPICAL. 2. PIPE CHASE ABOE BASEMEN MECHANICAL ROOM 009. 3. WASE DROPS FROM BELOW FIRS FLOOR LEEL O BELOW BASEMEN LEEL. 4. NEW DOMESIC SUPPLY LINES O IE INO EXISING MAINS. 5. PROIDE ACCESS O ISOLAION ALES. 6. CONNEC O EXIS 2" (2 PSI) GAS SERICE DOWNSREAM OF MEER. 2050 ADDED CFH. COORDINAE WIH GAS SUPPLIER FOR YARD LINE, REGULAOR AND MEER SIZE. 7. INCREASE SIZE OF MEER PAD O SUPPOR GAS MEER AND PIPING. 8. HEA RACE RO WAER PIPING FROM MECHANICAL SHED O AIR HANDLER. E E2 E3 E4 E5 E6 E7 E8 E9 E0 E E2 E3 XX AAA BBB N 3 P-40 L- PRIAE 69 OILE 68A L- 4" W(E) SEMI PRIAE 68 SEMI PRIAE 68 OILE 69A 2" (E) S LAUNDRY 65 4" 64 W(E) EXISING SUPPLY ROOM 2" (E) PRIAE PRIAE PRIAE PRIAE PRIAE PRIAE SEMI-PRIAE SEMI-PRIAE 62 6 60 59 58 57 54 63 L- L- PRIAE L- L- L- L- L- L- 55 L- 2 P-40 OILE OILE OILE OILE OILE 203 96 204 97 98 OILE 99 OILE OILE OILE OILE 200 4" W(E) 20 202 94 2" (E) OILE OILE OILE 55A 24 54A OILE 53A 3" W(E) 3/4" DHW(E) PRIAE 53 3/4" DCW(E) L- ELLIO WORKGROUP ARCHIECURE LLC 44 West Ute Blvd, Suite 00 Park City, Utah 84098 435-649-0092 or 80-45-839 elliottworkgroup.com MEP GAS SORAGE - HR RAED 9 MED GAS SUPPOR - HR RAED 92 4 P-40 BOILER ROOM - HR RAED 90 8 3/4" LPG G ROS 3/4" 3/4" AHU H N2 N3 N4 PRIAE 70 PRIAE 7 L- 3" WOILE (E) L- OILE 70A 7A OILE 205 S2 S3 2" UP(E) /2" DCW(E) 2" (E) EXISING NURSE SAION 36 /4" DHW(E) 34 /2" DHW(E) EXISING BAHING 2" DCW(E) ELEAOR 45 EXISING BEAUY / BARBER EXISING ACIIY SPACE 37 EXISING PRIAE DINING 2-B 2" (E) /4" DCW(E) 2" (E) " DCW(E) UIL " DHW(E) 3/4" DHW(E) 47 3" (E) 2" (E) EXISING NURSE SAION 46 EXISING DINING EXISING ACIIY SPACE PRIAE EXISING ACIIY SPACE 40 42 43 3" UP(E) EX OFFICE EX OFFICE 44 45 Room 52 EX SOCIAL SERICES CLEAN 48 COPY 49 OILE 52A ADMINISRAION 5 L- SEMI-PRIAE 52 REGISERED PROFESSIONAL No. 87737 JEFFREY S. WAKINS 04.20.208 SAE OF UAH ENGINEER SOUH DAIS COMMUNIY HOSPIAL 22 02 N5 N6 N7 YY PRIAE 72 PRIAE 73 PRIAE 74 3" W(E) L- L- L- 3 SEMI-PRIAE 75 2 OILE SOILED 72A 3 OILE CLEAN 73A 30 2" DCW(E) OILE 2" 74ADHW(E) 3/4" DHWR(E) S4 S5 S6 4 " DHW EX OILE 28 SAIRS 33 " DCW 5 EXISING MED ROOM 23 EXISING NURSE SAION 25 2" (E) 3" UP(E) /2" DCW(E) 3" (E) EXAM ROOM 2-A ROLL-IN SHOWER 24 EXISING ACIIY SPACE 20 3/4" GPM EXISING DINING 9 P-40 EXISING PHYSICAL HERAPY GYM 5 EX HEAD NURSE EXIS P WORK 03 3 WOMEN 05 EX OFFICE MEN 2 06 EXISING ACIIY SPACE 7 EXISING ADL RAINING 8 07 2" (E) " DCW(E) EXISING NURSE SAION /4" DHW(E) " DHW(E) 4" W(E) 3/4" DHWR(E) L- OILE 89A SOIL 09 UIL 0 3 2" (E) 89 3" UP(E) 2" (E) 4" W(E) OILE 88A SEMI-PRIAE L- SEMI-PRIAE 88 Orchard Cove Renovation 485 E 500 S Bountiful, U 8400 OILE OILE OILE OILE OILE OILE OILE OILE OILE OILE OILE OILE 75A L- 76A L- 77A 78A 79A 80A 208 209 20 2 22 23 OILE L- L- L- L- L- L- L- L- L- L- 2" (E) 2" (E) 2" (E) OILE 93 92 L- No. Date Description 5/4/8 ADDENDUM # PRIAE 76 PRIAE 77 PRIAE 78 PRIAE 79 PRIAE PRIAE PRIAE PRIAE PRIAE PRIAE PRIAE 80 8 82 83 84 85 86 SEMI-PRIAE 87 3 2" (E) 3" W DN(E) LEEL PLUMBING PLAN SCALE: 3/32" = '-0" ZZ AA 6 GAS MEER 7 BB ISSUE DAE: 208.04.20 OWNER PROJEC NO:. CONRAC NO:. DRAWN BY: CHECKED BY: DESIGNED BY: EWG PROJEC NO: COPYRIGH: KJM JSW KJM 207.60 Elliott Workgroup Architecture, LLC SHEE ILE LEEL PLUMBING PLAN AN BOERUM & FRANKASSOCIAES, INC. CONSULING ENGINEERS W W W. B F A. C O M Salt Lake City Logan St. George empe 330 South 300 East Salt Lake City, U 84 BFA Project Number: 7574 80.530.348 80.530.350 F P-0 SHEE OF
# KEYED NOES N6 N7 4 5 3 LPG 3' - 4" 2" (" WC) LPG SPS -2 MP LPG FS- ENLARGED SHED PLAN SCALE: /4" = '-0" AA ' - 0" 20 " DCW UP SPS - MAC SPS 2- O2 " 3" UP " DCW DN 3/4" 2/2" 4 2/2" FS- 3/4" 7 G G 5 3/4" /2" " DCW UP 2/2" G UP B 4 4 2" PC 3/4" LPG G LPG SPS 2-2 SPS 3-2 6 DHX LPG BASEMEN LEEL PLUMBING PLAN ENLARGED PLAN SCALE: /4" = '-0" MA 2 8 FCO DCW(E) 9 2" PC 3/4" 2" 2 G 8 PC LPG 4' - 0" 20 2" DCW UP(E) 3/4" DHWR UP(E) 2" DHW UP(E) DHW(E) RCP DHWR(E) 2" 6 0 3/4" 5 ' - 0" 2" 2" W(E) 7 PC 2" PC B 2 2 SPS 3- LPG RO ROS S 3/4" ROS 3/4" 3/4" ROS DN HWP HWP 2 L 9 B L- S4 S5 WC EX OILE SD 28 E4 SH " FD- WC- 2" SH- " EXISING MED ROOM 23 ROLL-IN SHOWER 2 2 24 " 4" 4" L- 3 " 3/4" 4" W DN SCALE: /4" = '-0" YP. PAIEN ROOM EXAM SINK SCALE: /4" = '-0" 2" 3/4" /2" 2 3/4" AAA BBB EXAM ROOM 2-A 3 EXISING ACIIY SPACE ROLL-IN SHOWER & EXAM RM ENLARGED PLUMBING PLAN FIRE SPRINKLERS SYSEM EQUIPMEN SPRINKLERS: L 20 AUOMAIC FIRE SPRINKLERS AND PIPING GENERAL NOES 3 2 MANUFACURER SH W L- WC L-2 YCO, RELIABLE, IKING, OR ICAULIC SEMI-RECESSED, WHIE, MACH EXISING K-FACOR PIPE HANGERS UL LISED & NFPA #3, SEISMIC BRACING PER & SUPPORS NFPA 3 CHAPER 9 PIPING: SCHEDULE 40 OR HREADABLE HINWALL FIINGS: UL LISINGS & NFPA #3 MECHANICAL EE: FLEXIBLE SPRINKLER DROPS: ICAULIC SERIES 920 OR 920N ICAULIC AH2 MAY BE USED IF A HYDRAULIC CALCULAION IS PROIDED A. BUILDING HAS AN EXISING SPRINKLER SYSEM INSALLED O PROEC SHELLED SPACE AND ALL OHER SURROUNDING AREAS. SCOPE OF WORK SHALL CONSIS OF ADDING/RELOCAING SPRINKLERS FOR NEW FLOOR AND CEILING PLAN INCLUDING HEIGH ADJUSMENS. B. MAKE CONNECION O EXISING PIPING AS NEEDED USING MECHANICAL EES, PLAIN END OR HREADED FIINGS. C. AUOMAIC, WE FIRE SPRINKLER SYSEM SHALL BE DESIGNED, AND INSALLED IN ACCORDANCE WIH NFPA # 3, 203 EDIION. D. SHOP DRAWINGS, CALCULAIONS AND MAERIAL SUBMIALS SHALL BE SUBMIED O HE ENGINEER AND FIRE MARSHALL. E. ANY SPRINKLER MODIFIER OR MOED SHALL BE REPLACED WIH A NEW QUICK RESPONSE SPRINKLER. ANY COMPARMEN CONAINING A MODIFIED SPRINKLER SHALL HAE QUICK RESPONSE SPRINKLERS INSALLED HROUGHOU HE COMPARMEN. EXENDED COERAGE SPRINKLERS MAY BE USED IF HEY ARE CURRENLY INSALLED IN HE EXISING AREA. IF EXENDED COERAGE SPRINKLERS ARE USED HEY SHALL BE INSALLED PER HE MANUFACURER'S REQUIREMENS. F. SPRINKLER & PIPING SHALL BE PROIDED HROUGHOU HE BUILDING, WIH QUICK RESPONSE SPRINKLERS, SPRINKLERS SHALL ALSO BE PROIDED O PROEC COMBUSIBLE SPACES HROUGHOU HE BUILDING. G. A WARRANY, FOR PRODUC AND SYSEM OPERAIONS SHALL BE PROIDED FOR ONE YEAR, UPON SYSEM ACIAION ND ACCEPANCE. DCW DHW YP. PAIEN ROOM EXAM SINK 2 SCALE: /4" = '-0". PLUMBING FOR SINK O BE IED INO EXISING LAAORY. 2. 4" WASE LINE HROUGH FLOOR O BELOW BASEMEN LEEL. SEE SHEE P-00. 3. PROIDE ACCESS O ISOLAION ALES. 4. NAURAL GAS FIRED BOILERS WIH LOW PRESSURE GAS BACK UP CONNECIONS. 5. EXISING AO SMIH BH 99 WAER HEAERS. 6. EXISING WAER SOFENER SYSEM. 7. EXISING M. 8. EXISING PRESSURE REDUCING SAION. 9. EXISING ELECRICAL PANELS. 0. PROIDE SEISMIC RESRAIN SRAPS FOR WAER SOFENER AND BRINE ANK.. EXISING DOMESIC RECIRCULAION PUMP 2. IE MAKE UP WAER LINE INO EXISING MAIN DOWNSREAM OF WAER SOFENERS. 3. 000 GALLON EASERN SORAGE PROPANE ANK. LOCAE 0' FROM CREEK FENCE AND 0' MECHANICAL SHED. 4. QUICK FILL ALE DCW MAKE UP O HYDRONIC WAER HEAING SYSEM. REFER O SHEE M-70. 5. INSALL BACKFLOW PREENER ON DOMESIC COLD WAER LINE SERING MECHANICAL SHED. 6. SEE SHEE P-00 FOR CONINUAION. 7. LB O 4 OZ GAS PRESSURE REGULAOR 30 CFH. 8. 2 LB O LB GAS PRESSURE REGULAOR 2050 CFH. 9. EXEND AND CONNEC O HUMIDIFIER. 20. REFER O SRUCURAL DRAWINGS AND SECIONS FOR AREA WELL CONSRUCION. 2. HE EXISING FIRE SPRINKLERS IN HIS AREA ARE O BE MODIFIED, REPLACED, OR ADDED AS REQUIRED BY NFPA 3-203. HE FIRE SPRINKLER CONRACOR SHALL FIELD ERIFY HE LOCAION OF HE EXISING FIRE SPRINKLERS. ADD/RELOCAE AS NECESSARY FOR HE REMODELED SPACE, INCLUDING NEW FLOOR PLAN, CEILING PLAN, AND CEILING HEIGH ADJUSMENS. ALL REMOED SPRINKLERS SHALL BE REPLACED WIH NEW QUICK RESPONSE SPRINKLERS. PLEASE REFER O HE AUOMAIC FIRE SPRINKLERS AND PIPING GENERAL NOES ON HIS PAGE FOR ADDIIONAL INFORMAION. W W W. B F A. C O M 330 South 300 East AN BOERUM & FRANKASSOCIAES, INC. CONSULING ENGINEERS Salt Lake City Logan St. George empe Salt Lake City, U 84 BFA Project Number: 7574 80.530.348 80.530.350 F ELLIO WORKGROUP ARCHIECURE LLC 44 West Ute Blvd, Suite 00 Park City, Utah 84098 435-649-0092 or 80-45-839 elliottworkgroup.com REGISERED SAE EWG PROJEC NO: COPYRIGH: PROFESSIONAL No. 87737 JEFFREY S. WAKINS 04.20.208 OF UAH Orchard Cove Renovation ENGINEER SOUH DAIS COMMUNIY HOSPIAL 485 E 500 S Bountiful, U 8400 No. Date Description 5/4/8 ADDENDUM # ISSUE DAE: 208.04.20 OWNER PROJEC NO:. CONRAC NO:. DRAWN BY: CHECKED BY: DESIGNED BY: SHEE KJM JSW KJM 207.60 Elliott Workgroup Architecture, LLC SHEE ILE ENLARGED PLUMBING PLANS P-40 OF
2 7/8" 5" YP. 6" 6 7/8" 2 5/8" WALL (BY OHERS) C.I. COER AND FRAME FINISHED GRADE CLEANOU PLUG 9 /4" MAIN LINE PRESSURE SWICH 8"x8"x6" HICK CONCREE PAD 4" C.I. CEMEN PACH OERALL MANIFOLD LENGH SEE CHAR BELOW MAIN LINE GAUGE CONCREE PIPE (SIZE AS SHOWN ON PLANS) 4" CONCREE PIPE CYLINDERS PER BANK OERALL LENGH 2" 2 24" PLAN IEW 3 4 MED GAS MANIFOLD 47" 5 57" 6 67" 7 77" 8 9 0 2 87" 97" 07" 7 27 MAIN LINE PRESSURE SWICH HIGH PRESSURE SIGNAL O MASER ALARM PANEL (BY AUOMAIC EMPERAURE CONROLS CONRACOR) LOW PRESSURE SIGNAL O MASER ALARM PANEL CLEANOU O GRADE DEAIL (COG) SCALE: 2" = '-0" RESERE IN USE SIGNAL: O MASER ALARM PANEL (BY ELECRICAL CONRACOR) POWER FEED -20 OL,. 60 Hz EMERGENCY CIRCUI (BY ELECRICAL CONRACOR) MOUNING BRACKE (YP.) HEADER EXENSION (YP.) H-YPE CYLINDERS (SUPPLIED BY OHERS) WALL MOUNED POWER SUPPLY 6" FACORY INSALLED SOURCE ALE MAIN OULE O2 FRON IEW MAIN LINE PRESSURE GAUGE /2" DIA. EN LINE RUN O OUSIDE URN DOWN AND SCREEN (SEE NOE 7) RELIEF ALE OULE PRESSURE CONROL CABINE FLEXIBLE CYLINDER CONNECIONS (YP.) 8 /4". 2. 3. 4. 5. 6. 7. 8. NOES O FACILIY FIRE RAED PENERAION O MACH WALL WALL (BY OHERS) ACCESSORIES BEYOND SOURCE ALE SUPPLIED BY ENDOR AND INSALLED BY CONRACOR. ALL PIPE AND FIINGS BEYOND SOURCE ALE AND RELIEF ALE OULE SUPPLIED BY MECHANICAL. INDIIDUALLY SECURE EACH CYLINDER WIH RACKS, CHAINS, OR OHER FASENINGS O PREEN DAMAGE. NEER PERMI OIL, GREASE OR OHER COMBUSIBLE MAERIAL O COME IN CONAC WIH CYLINDERS, MANIFOLDS AND CONNECIONS. REFER O DRAWINGS FOR ACUAL CYLINDER QUANIIES. MANIFOLD DIMENSIONS ARE BASED ON H-YPE CYLINDERS. FULL CYLINDERS OF COMPRESSED GAS, OHER HA N2O AND CO2, NORMALLY CONAIN APPROX. 2,200 PSIG. N20 AND CO2 ARE LIQUEFIED IN SANDARD FULL CYLINDERS AND CYLINDER PRESSURES ARY WIH EMPERAURE. RELIEF ALE PIPING SHALL BE BRAZED WIH A SILER BRAZING FILLER MAERIAL. ALL MANIFOLDS OHER HAN 02 SHALL USE SAINLESS SEEL PIGAILS. O2 MANIFOLD SHALL BE SUPPLIED WIH PRE-FORMED RIGID COPPER PIGAILS. 2 COUNERSUNK SCREW ACCESS COER AND FRAME. OP OF COER SHALL BE FLUSH W/OP OF FLOOR. CAS IRON /8 BEND BRASS CLEANOU PLUG AND FERRULE FINISHED FLOOR BALANCE OF PIPING SAME AS CLEANOU O GRADE. WASE PIPING FLOOR CLEANOU DEAIL NO O SCALE /8 BEND IF CLEANOU OCCURS A END OF LINE ELLIO WORKGROUP ARCHIECURE LLC 44 West Ute Blvd, Suite 00 Park City, Utah 84098 435-649-0092 or 80-45-839 elliottworkgroup.com REGISERED SAE PROFESSIONAL No. 87737 JEFFREY S. WAKINS 04.20.208 OF UAH ENGINEER SOUH DAIS COMMUNIY HOSPIAL Orchard Cove Renovation 485 E 500 S Bountiful, U 8400 4 MED GAS MANIFOLD NO O SCALE 3 HEA EXCHANGER DEAIL NO O SCALE SHU-OFF ALE (YP.) CHECK ALE (YP.) LINE PRESSURE ALARM SWICH PRESSURE LINE INDICAOR No. Date Description 5/4/8 ADDENDUM # WALL MAIN LINE EXERIOR CONNECION POIN FINISHED FLOOR RELIEF ALE AND EN ISSUE DAE: 208.04.20 OWNER PROJEC NO:. CONRAC NO:. DRAWN BY: CHECKED BY: DESIGNED BY: EWG PROJEC NO: COPYRIGH: Author JSW KJM 207.60 Elliott Workgroup Architecture, LLC SHEE ILE 5 PROPANE ANK DEAIL NO O SCALE 6 EMERGENCY OXYGEN SUPPLY CONNECION NO O SCALE W W W. B F A. C O M 330 South 300 East AN BOERUM & FRANKASSOCIAES, INC. CONSULING ENGINEERS Salt Lake City Logan St. George empe Salt Lake City, U 84 BFA Project Number: 7574 80.530.348 80.530.350 F PLUMBING DEAILS P-50 SHEE OF
SPECIFICAION INDEX 2 000 Water-Based Fire-Suppression Systems 220500 Common Work Results for Plumbing 22053 Common Motor Requirements for Plumbing Equipment 22059 Meters and Gages for Plumbing Piping 220523 General-Duty alves for Plumbing Piping 220529 Hangers and Supports for Plumbing Piping and Equipment 220533 Heat racing for Plumbing Piping 220548 ibration and Seismic Controls for Plumbing Piping and Equipment 220553 Identification for Plumbing Piping and Equipment 22079 Plumbing Piping Insulation 226 Domestic Water Piping 229 Domestic Water Piping Specialties 2223 Domestic Water Pumps 2236 Sanitary Waste and ent Piping 2239 Sanitary Waste Piping Specialties 22323 Sanitary Waste Interceptors 2243 Facility Storm Drainage Piping 22423 Storm Drainage Piping Specialties 223502 Packaged Domestic Water Steam-o-Water Heat Exchangers 224000 Plumbing Fixtures 224500 Emergency Plumbing Fixtures 22476 Pressure Water Coolers 2263 Compressed-Air Piping for Laboratory and Healthcare Facilities 2269 Compressed-Air Equipment for Laboratory and Healthcare Facilities 22623 acuum Piping for Laboratory and Healthcare Facilities 22629 acuum Equipment for Laboratory and Healthcare Facilities 22633 Gas Piping for Laboratory and Healthcare Facilities 226400 Medical Gas Alarms 226700 Deionized Pure Water System 22670 Pure Water Piping 23000 Mechanical Requirements 23050 emporary Use of Equipment and Systems 230500 Common Work Results for HAC 23053 Common Motor Requirements for HAC Equipment 23056 Expansion Fittings and Loops for HAC Piping 23057 Sleeves and Sleeve Seals for HAC Piping 23058 Escutcheons for HAC Piping 23059 Meters and Gages for HAC 230523 General-Duty alves for HAC Piping 230529 Hangers and Supports for HAC Piping and Equipment 230548 ibration and Seismic Controls for HAC 230550 Operation and Maintenance of HAC Systems 230553 Identification for HAC Piping and Equipment 230593 esting, Adjusting, and Balancing for HAC 23073 Duct Insulation 23076 HAC Equipment Insulation 23079 HAC Piping Insulation elliott workgroup architecture LLC SPECIFICAION INDEX Specification Index -
230900 Instrumentation and Control for HAC 2323 Facility Natural-Gas Piping 2323 Hydronic Piping 2326 Hydronic Piping Specialties 23223 Hydronic Pumps 23223 Steam and Condensate Heating Piping 23226 Steam and Condensate Piping Specialties 232300 Refrigerant Piping 23253 Water reatment for Closed-Loop Hydronic Systems 23300 Common Duct Requirements 2333 Metal Ducts 2336 Non-Metal Ducts 2339 HAC Casings 233300 Air Duct Accessories 233423 HAC Power entilators 233600 Air erminal Units 23373 Diffusers, Registers, and Grilles 23374 Fixed Louvers 23500 Breechings, Chimneys, and Stacks 23528 Flexible Steel Water-ube Boilers 23743 Packaged, Outdoor, Rooftop Units 23750 HW Piping System 23828 Split-System Wall Air-Conditioners 23823 Balance Heating and Cooling Units 23826 Hydronic Air Coils 23844 Humidifiers 33 633 Underground Hot Water piping System elliott workgroup architecture LLC SPECIFICAION INDEX Specification Index - 2
SECION 2 0 00 WAER-BASED FIRE-SUPPRESSION SYSEMS.0 GENERAL. RELAED DOCUMENS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 Specification Sections, apply to this Section..2 SUMMARY A. his Section includes the following fire-suppression piping inside the building:. Remodel to an existing wet-pipe sprinkler system including adding/relocating fire sprinklers as necessary for the remodeled space including new floor plan, ceiling plan and ceiling height adjustments. 2. All sprinklers removed shall be replaced with new quick response sprinklers. All sprinklers throughout the remodeled compartment shall be flat plate concealed quick response. Modify sprinklers adjacent to the remodel as required by NFPA 3. B. Related Sections include the following:. Division 0 Section "Fire Extinguisher Cabinets" and "Fire Extinguishers" for cabinets and fire extinguishers. 2. Division 22 Section "Facility Water Distribution Piping" for piping outside the building. 3. Division 28 Section "Fire Detection and Alarm" for alarm devices not specified in this Section. C. All black steel sprinkler pipe shall have a wall thickness less than or equal to schedule 40 and greater than schedule 0. D. All fire protection equipment, including piping, hangers, control valves, shall be UL listed and FM approved. A copy of the manufacturer s specification sheet for each specific component installed shall be included with shop drawings. E. Summary able: Item Underground service entrance piping, Alarm device, FDC Interior pipe type Sprinkler Finish Extended Coverage Center of ile Flexible Sprinkler Drops FM Global Calculations Summary Existing to remain Mains: Schedule 40 Branch-lines: hreadable thin-wall or schedule 40 Flat Plate Concealed Match existing k-factor and flow characteristics Required, Center thirds are acceptable Not allowed in remodel No Not required, Building occupancy to remain unchanged. No more than one fire sprinkler drop to be fed from an existing outlet. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000 -
.3 DEFINIIONS A. CPC: Chlorinated polyvinyl chloride plastic. B. CR: Chlorosulfonated polyethylene synthetic rubber. C. High-Pressure Piping System: Fire-suppression piping system designed to operate at working pressure higher than standard 75 psig. D. PE: Polyethylene plastic. E. Underground Service-Entrance Piping: Underground service piping below the building..4 SYSEM DESCRIPIONS A. Wet-Pipe Sprinkler System: Automatic sprinklers are attached to piping containing water and that is connected to water supply. Water discharges immediately from sprinklers when they are opened. Sprinklers open when heat melts fusible link or destroys frangible device. Hose connections are included if indicated..5 PERFORMANCE REQUIREMENS A. Standard Piping System Component Working Pressure: Listed for at least 75 psig. B. Original fire sprinkler system design to remain. All remodel work shall match the existing installation for pressure and flow characteristics.. Sprinkler Occupancy Hazard Classifications: a. Building Service Areas: Ordinary Hazard, Group. b. Electrical Equipment Rooms: Ordinary Hazard, Group. c. General Storage Areas: Ordinary Hazard, Group. d. Mechanical Equipment Rooms: Ordinary Hazard, Group. e. Office and Public Areas: Light Hazard. 2. Minimum Density for Automatic-Sprinkler Piping Design: a. Light-Hazard Occupancy: 0.0 gpm over 500-sq. ft. area. b. Ordinary-Hazard, Group Occupancy: 0.5 gpm over 500-sq. ft. area. c. Ordinary-Hazard, Group 2 Occupancy: 0.20 gpm over 500-sq. ft. area. d. Special Occupancy Hazard: As determined by authorities having jurisdiction. 3. Maximum Protection Area per Sprinkler: a. Office Spaces: 225 sq. ft.. b. Storage Areas: 30 sq. ft.. c. Mechanical Equipment Rooms: 30 sq. ft.. d. Electrical Equipment Rooms: 30 sq. ft.. e. Other Areas: According to NFPA 3 recommendations, unless otherwise indicated. 4. otal Combined Hose-Stream Demand Requirement: According to NFPA 3, unless otherwise indicated: elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-2
a. Light-Hazard Occupancies: 00 gpm for 30 minutes. b. Ordinary-Hazard Occupancies: 250 gpm for 60 to 90 minutes. C. Seismic Performance: Fire-suppression piping shall be capable of withstanding the effects of earthquake motions determined according to NFPA 3..6 SUBMIALS A. Product Data: For the following:. Piping materials, including sprinkler specialty fittings. 2. Pipe hangers and supports, including seismic restraints. 3. alves, including listed fire-protection valves, unlisted general-duty valves, and specialty valves and trim. 4. Sprinklers, escutcheons, and guards. Include sprinkler flow characteristics, mounting, finish, and other pertinent data. B. Shop Drawings: Diagram power, signal, and control wiring. C. Approved Sprinkler Piping Drawings: Working plans, prepared according to NFPA 3, that have been approved by authorities having jurisdiction, including hydraulic calculations, if applicable. Drawings are to be approved by Engineer prior to submission to State Fire Marshal. D. Seismic Calculations. E. Field est Reports and Certificates: Indicate and interpret test results for compliance with performance requirements and as described in NFPA 3. Include "Contractor's Material and est Certificate for Aboveground Piping" and "Contractor's Material and est Certificate for Underground Piping." F. Field quality-control test reports. G. Operation and Maintenance Data: For sprinkler specialties to include in emergency, operation, and maintenance manuals..7 QUALIY ASSURANCE A. Installer Qualifications:. An experienced installer who has designed and installed fire-suppression piping similar to that indicated for this Project and obtained design approval and inspection approval from authorities having jurisdiction. he Engineer requires evidence to support the ability of the contractor to perform work in the scope and volume as specified. A contractor, who cannot show such experience, may be found not suitable to perform the work. he following are the approved contractors for this project: a. PRE-APPROED CONRACORS LIS ) Certified Fire 2) Chaparral Fire 3) Cottle Fire 4) Delta Fire 5) FireFly Fire Protection 6) Fire Services Inc. 7) Firerol elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-3
8) Quality Fire Protection 9) Simplex-Grinnell 0) he Safety eam ) Western Automatic 2) Or prior approved equal b. A contractor not listed in the PRE-APPROED CONRACORS LIS must receive prior approval from the engineer to bid this project. B. Installer's responsibilities include designing, fabricating, and installing fire-suppression systems and providing professional engineering services needed to assume engineering responsibility. Base calculations on results of fire-hydrant flow test.. Engineering Responsibility: Preparation of working plans, calculations, and field test reports by a qualified professional engineer or NICE Level III technician. C. Welding: Qualify processes and operators according to ASME Boiler and Pressure essel Code: Section IX. D. NFPA Standards: Fire-suppression-system equipment, specialties, accessories, installation, and testing shall comply with the following:. NFPA 3-203, "Installation of Sprinkler Systems." E. International Conference of Building Code Officials codes and standards complying with the following:. IBC-205, International Building Code. 2. IFC-205, International Fire Code. 3. Utah Amendments.8 COORDINAION A. Coordinate layout and installation of sprinklers with other construction that penetrates ceilings, including light fixtures, HAC equipment, and partition assemblies..9 EXRA MAERIALS A. Furnish extra materials described below that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.. Sprinkler Cabinets: Include number of sprinklers required by NFPA 3 and sprinkler wrench. Include sprinklers and wrench for each type of sprinkler on Project. 2.0 PRODUCS 2. MANUFACURERS A. In other Part 2 articles where titles below introduce lists, the following requirements apply to product selection: elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-4
. Manufacturers: Subject to compliance with requirements, provide products by one of the manufacturers specified. 2.2 SEEL PIPE AND FIINGS A. hreaded-end, Standard-Weight Steel Pipe: ASM A 53/A 53M, ASM A 35, or ASM A 795, hot-dip galvanized where indicated and with factory- or field-formed threaded ends.. Cast-Iron hreaded Flanges: ASME B6.. 2. Malleable-Iron hreaded Fittings: ASME B6.3. 3. Gray-Iron hreaded Fittings: ASME B6.4. 4. Steel hreaded Pipe Nipples: ASM A 733, made of ASM A 53/A 53M or ASM A 06, Schedule 40, seamless steel pipe hot-dip galvanized where indicated. Include ends matching joining method. 5. Steel hreaded Couplings: ASM A 865 hot-dip galvanized-steel pipe where indicated. B. Plain-End, Standard-Weight Steel Pipe: ASM A 53/A 53M, ASM A 35, or ASM A 795 hot-dip galvanized-steel pipe where indicated.. Locking-Lug Fittings: UL 23, ductile-iron body with retainer lugs that require one-quarter turn to secure pipe in fitting not allowed. C. Plain-End, Standard-Weight Steel Pipe: ASM A 53/A 53M, ASM A 35, or ASM A 795 hot-dip galvanized-steel pipe where indicated.. Steel Welding Fittings: ASM A 234/A 234M, and ASME B6.9 or ASME B6.. 2. Steel Flanges and Flanged Fittings: ASME B6.5. D. Grooved-End, Standard-Weight Steel Pipe: ASM A 53/A 53M, ASM A 35, or ASM A 795, hotdip galvanized where indicated and with factory- or field-formed, roll-grooved ends.. Grooved-Joint Piping Systems: a. Manufacturers: ) Anvil International, Inc. 2) Central Sprinkler Corp. 3) ictaulic Co. of America. 4) Ward Manufacturing. b. Grooved-End Fittings: UL-listed, ASM A 536, ductile-iron casting with OD matching steelpipe OD. c. Grooved-End-Pipe Couplings: UL 23 and AWWA C606, rigid pattern, unless otherwise indicated; gasketed fitting matching steel-pipe OD. Include ductile-iron housing with keys matching steel-pipe and fitting grooves, pre-lubricated rubber gasket listed for use with housing, and steel bolts and nuts. E. hreaded-end, hreadable, hin-wall Steel Pipe: ASM A 35 or ASM A 795, with wall thickness less than Schedule 40 and greater than Schedule 0, and with factory- or field-formed threaded ends.. Cast-Iron hreaded Flanges: ASME B6.. 2. Malleable-Iron hreaded Fittings: ASME B6.3. 3. Gray-Iron hreaded Fittings: ASME B6.4. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-5
4. Steel hreaded Pipe Nipples: ASM A 733, made of ASM A 53/A 53M or ASM A 06, Schedule 40, seamless steel pipe. 5. Steel hreaded Couplings: ASM A 865. F. Plain-End, hreadable, hin-wall Steel Pipe: ASM A 35 or ASM A 795, with wall thickness less than Schedule 40 and greater than Schedule 0.. Locking-Lug Fittings: UL 23, ductile-iron body with retainer lugs that require one-quarter turn to secure pipe in fitting not allowed. G. Plain-End, hreadable, hin-wall Steel Pipe: ASM A 35 or ASM A 795, with wall thickness less than Schedule 40 and greater than Schedule 0.. Steel Welding Fittings: ASM A 234/A 234M, and ASME B6.9 or ASME B6.. 2. Steel Flanges and Flanged Fittings: ASME B6.5. H. Grooved-End, hreadable, hin-wall Steel Pipe: ASM A 35 or ASM A 795, with wall thickness less than Schedule 40 and greater than Schedule 0, and with factory- or field-formed, roll-grooved ends.. Grooved-Joint Piping Systems: a. Manufacturers: ) Anvil International, Inc. 2) Central Sprinkler Corp. 3) ictaulic Co. of America. 4) Ward Manufacturing. b. Grooved-End Fittings: UL-listed, ASM A 536, ductile-iron casting with OD matching steelpipe OD. c. Grooved-End-Pipe Couplings: UL 23 and AWWA C606, rigid pattern, unless otherwise indicated; gasketed fitting matching steel-pipe OD. Include ductile-iron housing with keys matching steel-pipe and fitting grooves, pre-lubricated rubber gasket listed for use with housing, and steel bolts and nuts. 2.3 LISED FIRE-PROECION ALES A. alves shall be FMG approved, with 75-psig minimum pressure rating. alves shall have 250-psig minimum pressure rating if valves are components of high-pressure piping system. B. Ball alves: Comply with UL 09, except with ball instead of disc.. NPS -/2 and Smaller: Bronze body with threaded ends. 2. NPS 2 and NPS 2-/2: Bronze body with threaded ends or ductile-iron body with grooved ends. 3. NPS 3: Ductile-iron body with grooved ends. 4. Manufacturers: a. NIBCO. b. ictaulic Co. of America. C. Butterfly alves: UL 09. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-6
. NPS 2 and Smaller: Bronze body with threaded ends. a. Manufacturers: ) Global Safety Products, Inc. 2) Milwaukee alve Company. 2. NPS 2-/2 and Larger: Bronze, cast-iron, or ductile-iron body; wafer type or with flanged or grooved ends. a. Manufacturers: ) Central Sprinkler Corp. 2) McWane, Inc.; Kennedy alve Div. 3) Mueller Company. 4) NIBCO. 5) ictaulic Co. of America. D. Check alves NPS 2 and Larger: UL 32, swing type, cast-iron body with flanged or grooved ends.. Manufacturers: a. American Cast Iron Pipe Co.; Waterous Co. b. Central Sprinkler Corp. c. Clow alve Co. d. Crane Co.; Crane alve Group; Crane alves. e. Crane Co.; Crane alve Group; Jenkins alves. f. Globe Fire Sprinkler Corporation. g. Grinnell Fire Protection. h. Hammond alve. i. McWane, Inc.; Kennedy alve Div. j. Mueller Company. k. NIBCO. l. Potter-Roemer; Fire Protection Div. m. Reliable Automatic Sprinkler Co., Inc. n. Stockham. o. United Brass Works, Inc. p. ictaulic Co. of America. q. Watts Industries, Inc.; Water Products Div. 2.4 UNLISED GENERAL-DUY ALES A. Ball alves NPS 2 and Smaller: MSS SP-0, 2-piece copper-alloy body with chrome-plated brass ball, 600-psig minimum CWP rating, blowout-proof stem, and threaded ends. B. Check alves NPS 2 and Smaller: MSS SP-80, ype 4, Class 25 minimum, swing type with bronze body, nonmetallic disc, and threaded ends. C. Gate alves NPS 2 and Smaller: MSS SP-80, ype 2, Class 25 minimum, with bronze body, solid wedge, and threaded ends. D. Globe alves NPS 2 and Smaller: MSS SP-80, ype 2, Class 25 minimum, with bronze body, nonmetallic disc, and threaded ends. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-7
2.5 SPRINKLERS A. Sprinklers shall be UL listed or FMG approved, with 75-psig minimum pressure rating. Sprinklers shall have 250-psig minimum 300-psig pressure rating if sprinklers are components of high-pressure piping system. B. Manufacturers:. Reliable Automatic Sprinkler Co., Inc. 2. yco Fire Products 3. ictaulic Co. of America. 4. iking Corp. C. Automatic Sprinklers: With heat-responsive element complying with the following:. UL 99, for nonresidential applications. D. Sprinkler ypes and Categories: Nominal /2-inch orifice for "Ordinary" temperature classification rating, unless otherwise indicated or required by application. E. Sprinkler types, features, and options as follows:. Concealed ceiling sprinklers, including cover plate. 2. Pendent sprinklers. 3. Quick-response sprinklers. 4. Sidewall sprinklers. 5. Upright sprinklers. F. Sprinkler Finishes: Chrome plated, bronze, and painted. G. Special Coatings: Wax, lead, and corrosion-resistant paint. H. Sprinkler Escutcheons: Materials, types, and finishes for the following sprinkler mounting applications. Escutcheons for concealed and semi-recessed type sprinklers are specified with sprinklers.. Ceiling Mounting: Flat plate concealed, white. 2. Sidewall Mounting: Semi-recessed, white. I. Sprinkler Guards: Wire-cage type, including fastening device for attaching to sprinkler. 3.0 EXECUION 3. PREPARAION A. Contractor to field verify all existing conditions. 3.2 EXAMINAION A. Proceed with installation only after unsatisfactory conditions have been corrected. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-8
3.3 PIPING APPLICAIONS A. Shop-weld pipe joints where welded piping is indicated. B. Do not use welded joints for galvanized-steel pipe. C. Flanges, flanged fittings, unions, nipples, and transition and special fittings with finish and pressure ratings same as or higher than system's pressure rating may be used in aboveground applications, unless otherwise indicated. D. Branch line piping: Use the following:. NPS 2 and Smaller: Schedule 40 or hreadable steel pipe with threaded ends; cast- or malleable-iron threaded fittings; and threaded joints. E. Mains: Use the following:. NPS 2-/2 and larger: Schedule 40 steel pipe with grooved ends & Welded outlets. 3.4 ALE APPLICAIONS A. Drawings indicate valve types to be used. Where specific valve types are not indicated, the following requirements apply:. Fire-Protection-Service alves: UL listed for applications where required by NFPA 3. 2. General-Duty alves: For applications where UL-listed valves are not required by NFPA 3. a. Shutoff Duty: Use gate, ball, or butterfly valves. b. hrottling Duty: Use globe, ball, or butterfly valves. 3.5 JOIN CONSRUCION A. Refer to Division 23 Section "Common Work Result for HAC" for basic piping joint construction. B. Steel-Piping, Grooved Joints: Use Schedule 40 steel pipe with cut or roll-grooved ends and Schedule 30 or thinner steel pipe with roll-grooved ends; steel, grooved-end fittings; and steel, keyed couplings. Assemble joints with couplings, gaskets, lubricant, and bolts according to coupling manufacturer's written instructions. Use gaskets listed for dry-pipe service for dry piping. 3.6 PIPING INSALLAION A. Refer to Division 23 Section "Common Work Result for HAC" for basic piping installation. B. Locations and Arrangements: Drawing plans, schematics, and diagrams indicate general location and arrangement of piping. Install piping as indicated, as far as practical.. Deviations from approved working plans for piping require written approval from authorities having jurisdiction. File written approval with Architect before deviating from approved working plans. C. Use approved fittings to make changes in direction, branch takeoffs from mains, and reductions in pipe sizes. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-9
D. Install unions adjacent to each valve in pipes NPS 2 and smaller. Unions are not required on flanged devices or in piping installations using grooved joints. E. Install flanges or flange adapters on valves, apparatus, and equipment having NPS 2-/2 and larger connections. F. Install sprinkler piping with drains for complete system drainage. G. Hangers and Supports: Comply with NFPA 3 for hanger materials. Install according to NFPA 3 for sprinkler piping.. No powder driven studs allowed. 2. Wrap-around braces are to be provided at end of branch lines. H. Earthquake Protection: Install piping according to NFPA 3 Chapter 9 requirements to protect from earthquake damage. Seismic Bracing shall be designed to withstand vertical forces and movement. I. Install piping with grooved joints according to manufacturer's written instructions. Construct rigid piping joints, unless otherwise indicated, or required by NFPA 3 for flexibility in seismic zones. 3.7 SPECIALY SPRINKLER FIING INSALLAION A. Install specialty sprinkler fittings according to manufacturer's written instructions. 3.8 ALE INSALLAION A. Refer to Division 23 Section "alves" for installing general-duty valves. Install fire-protection specialty valves, trim, fittings, controls, and specialties according to NFPA 3, manufacturer's written instructions, and authorities having jurisdiction. B. alves: Install fire-protection-service valves supervised-open, located to control sources of water supply except from fire department connections. Provide permanent identification signs indicating portion of system controlled by each valve. C. Double Check alve Assemblies: Install valves in vertical or horizontal position, per listings and for proper direction of flow. 3.9 SPRINKLER APPLICAIONS A. General: All sprinklers are to be quick response type. Sprinkler heads shall be of the latest design closed spray type for 55 F unless specified otherwise or required by code. Extended coverage heads shall not be used. Orifices larger than /2" may be used as required by density and spacing demands. Use sprinklers according to the following applications:. Rooms without Ceilings: Upright and/or pendent sprinklers. Provide mechanical guards on all heads at or below 7-0 height above the floor or where damage from room occupant use may occur. 2. Rooms with Ceilings: Flat plate concealed sprinklers. 3. Wall Mounting: Sidewall sprinklers with recessed escutcheon. 4. Spaces Subject to Freezing: Upright; pendent, dry-type; and sidewall, dry-type sprinklers. 5. Provide freeze proof type automatic sprinkler heads serving unconditioned spaces, areas subject to freezing and in other areas requiring their use. elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-0
6. Heads located within the air streams of unit heaters or other heat-emitting equipment shall be selected for proper temperature rating. 7. Sprinkler Finishes: Use sprinklers with the following finishes: a. Upright, Pendent, and Sidewall Sprinklers: Chrome in finished spaces exposed to view; rough bronze in unfinished spaces not exposed to view. b. Concealed Sprinklers: Rough brass, with White cover plate to match white ceiling tile color. Ceilings with gypsum board finish having matching color applied by the factory. Ceilings with wood finish to have brushed chrome or brushed copper finish as determined by Architect. B. Sprinklers: Use the following:. All sprinklers shall be listed, quick response type. 3.0 SPRINKLER INSALLAION A. Every effort shall be required to insure that the heads form a symmetrical pattern in the ceiling with the ceiling grid, lights, diffusers and grilles. Offsets shall be made in piping to accommodate ductwork in the ceiling. Heads should be symmetrical and all piping run parallel or perpendicular to building lines.. In no case shall sprinkler heads be installed closer than approved distances from ceiling obstructions and HAC ductwork. 2. Sprinkler heads shall not conflict with tile grids. 3. Sprinkler heads shall be located near center of corridors. B. Where layout of sprinkler heads is shown on reflected ceiling plans the locations shall be followed unless approval is obtained from the Architect or such locations shown do not meet the requirements of NFPA-3. In either case, approval of the Architect shall be obtained in writing before sprinkler head locations are changed. If the installation of additional heads is needed to conform to NFPA 3 requirements in areas where heads are shown on reflected ceiling plans, they shall be included in the contract price. C. Install sprinklers in patterns indicated. D. Do not install pendent or sidewall, wet-type sprinklers in areas subject to freezing. Use dry-type sprinklers with water supply from heated space. 3. CONNECIONS A. Connect water-supply piping and sprinklers where indicated. B. Electrical Connections: Power wiring is specified in Division 26, Alarm wiring is specified in Division 28. C. Connect alarm devices to fire alarm, Division 28. 3.2 LABELING AND IDENIFICAION A. Install labeling and pipe markers on equipment and piping according to requirements in NFPA 3 and and in Division 23 Section "Common Work Result for HAC." elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000 -
3.3 FIELD QUALIY CONROL A. Flush, test, and inspect sprinkler piping according to NFPA 3, "System Acceptance" Chapter. B. Replace piping system components that do not pass test procedures and retest to demonstrate compliance. Repeat procedure until satisfactory results are obtained. C. Report test results promptly and in writing to Architect and authorities having jurisdiction. D. Whether the underground serving the sprinkler system is done by this contractor or another, this contractor will be responsible to assure and have in his possession a certificate that the underground has been flushed and tested by the contractor who installed it in accordance with NFPA-24 prior to connection of the underground piping to the overhead sprinkler system. 3.4 CLEANING A. Clean dirt and debris from sprinklers. B. Remove and replace sprinklers having paint other than factory finish. 3.5 PROECION A. Protect sprinklers from damage until Substantial Completion. 3.6 COMMISSIONING A. erify that specialty valves, trim, fittings, controls, and accessories are installed and operate correctly. B. erify that specified tests of piping are complete and that Material est Certificates are complete. C. erify that damaged sprinklers and sprinklers with paint or coating not specified are replaced with new, correct type. D. erify that sprinklers are correct types, have correct finishes and temperature ratings, and have guards as required for each application. E. erify that fire department connections have threads compatible with local fire department equipment. F. Fill wet-pipe sprinkler piping with water. G. Coordinate with fire alarm tests. Operate as required. 3.7 DEMONSRAION & ESS A. Demonstrate equipment, specialties, and accessories. Review operating and maintenance information. B. All tests will be conducted as required by the local authority having jurisdiction, and in no case less than those required by NFPA standards. As a minimum, piping in the sprinkler system shall be tested at a water pressure at 200 psi for a period of not less two hours, or at 50 psi in excess of the normal pressure when the normal pressure is above 50 psi. Bracing shall be in place, and air shall be elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-2
removed from the system through the hydrants and drain valves before the test pressure is applied. No apparent leaks will be permitted on interior or underground piping. C. he local jurisdiction having authority and the Utah State Fire Marshal's office (where required) shall be notified at least three working days in advance of all tests and flushing. his includes any flushing of underground, hydrostatic testing, or flow testing that may be required. D. his contractor shall make all the required tests to the sprinkler system as required by code. He shall be responsible to assure that the Contractor est Certificates for the overhead, backflow and underground work are completed and delivered to the owner s insurance underwriter to assure proper insurance credit. E. All tests requiring the witnessing by local authorities will be the responsibility of this contractor. If tests are not run or do not have the proper witness, then they will be run later and all damage caused by the system, or caused in uncovering the system for such test, will be borne by this contractor. F. Final acceptance of the automatic sprinkler systems by AIG Global Property Risk Engineering is contingent upon field investigation and satisfactory completion of the Contractor s Material & est Certificate. 3.8 WARRANY A. his contractor shall warranty the sprinkler system and all its components for one year from the date of acceptance by the owner. Any costs incurred to extend any warranties of materials to assure this time frame shall be borne by this contractor. B. Provide Operation and Maintenance Manuals with correct as-builts test certificates and warranties included. A minimum 6 sets to be provided in red 3-ring binders. C. Electronic copy of AutoCAD as-built drawings shall also be provided on CD, with each O&M Manual. 3.9 FIELD QUALIY CONROL A. Flush, test and inspect sprinkler piping according to NFPA 3, System Acceptance Chapter. B. Replace piping system components that do not pass test procedures and retest to demonstrate compliance. Repeat procedure until satisfactory results are obtained. C. Report test results promptly and in writing to Architect and authorities having jurisdiction. END OF SECION elliott workgroup architecture LLC WAER-BASED FIRE-SUPPRESION SYSEM 2000-3