Title page CCSAUS certificate: EN 70034691 for EX Meggitt SA Route de Moncor 4 PO Box 1616 CH - 1701 Fribourg Switzerland CCSAUS certificate 70034691 www.meggittsensingsystems.com www.vibro-meter.com
THIS PAGE INTENTIONALLY LEFT BLANK
CCSAUS instructions specific to hazardous area installations 444-134-000-YY5 to YY9 The following instructions relevant to safe use in a hazardous area apply to equipment covered by the CCSAUS 70034691 certificate. 1 The certification marking is as follows: 70034691 Class I, Division 1, Groups A, B, C, D Ex ia IIC T6 T1 Ga Class 1, Zone 0 AEx ia IIC T6 T1 Ga Reference drawing PZ 8584. Class I, Division 2, Groups A, B, C, D Ex na IIC T6 T1 Gc Class 1, Zone 2 AEx na IIC T6 T1 Gc Reference drawing PZ 8585. 2 The equipment may be used in Zones 0, 1 and 2 with flammable gases and vapours, with apparatus groups IIA, IIB and IIC, and with temperature classes T1 to T6. Temperature classes depend on the operating temperatures of the sensor, cable and signal conditioner (see 4). 3 The equipment may also be used in Division 1 and Division 2 with Groups A, B, C, D. 4 The equipment is only certified for use in ambient temperatures in the range as specified below and should not be used outside this range. Sensor operating temperature: 70 to +350 C. Cable operating temperature: 54 to +260 C. Conditioner operating temperature: 54 to +125 C. Temperature classes depend on the operating temperatures of the sensor, cable and signal conditioner: Part T6 T5 T4 T3 T2 T1 Sensor +80 C +95 C +130 C +195 C +290 C +350 C Cable +80 C +95 C +130 C +195 C +260 C --- Conditioner +65 C +80 C +115 C +125 C --- --- 5 Installation shall be carried out in accordance with the applicable code of practice by suitably trained personnel. 6 There are no special checking or maintenance conditions. 7 With regard to explosion safety, it is not necessary to check for correct operation. 8 The equipment contains no user-replaceable parts and is not intended to be repaired by the user. Repair of the equipment is to be carried out by the manufacturer, or their approved agents, in accordance with the applicable code of practice. 9 Repair of this equipment shall be carried out in accordance with the applicable code of practice. 10 If the equipment is likely to come into contact with aggressive substances, such as acidic liquids or gases that may attack metals or solvents that may affect polymeric materials, then it is the responsibility of the user to take suitable precautions that prevent it from being adversely affected, thus ensuring that the type of protection is not compromised. 11 WARNING EXPLOSION HAZARD DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON-HAZARDOUS. CCSAUS certificate 70034691 1
Certificate of Compliance Certificate: 70034691 Project: 70034691 Master Contract: 175074 Date Issued: September 22, 2015 Certificate: 70034691 Master Contract: 175074 Project: 70034691 Date Issued: September 22, 2015 Issued to: Meggitt SA Rte de Moncor 4 Villars-sur-Glane, 1752 Switzerland Attention: Carlo Pellegrinelli The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. PRODUCTS Issued by: Sripriya Kalyanasundaram CLASS 2258 03 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non- Incendive Systems For Hazardous Locations. Class I, Division 1, Groups A, B, C and D Ex ia IIC T6..T1 Ga Part T6 T5 T4 T3 T2 T1 Sensor +80 C +95 C +130 C +195 C +290 C +350 C Cable +80 C +95 C +130 C +195 C +260 C -- Conditioner +45 C +60 C +95 C +125 C -- -- CLASS 2258 02 PROCESS CONTROL EQUIPMENT For Hazardous Locations Class I, Division 2, Groups A, B, C and D Ex na IIC T6..T1 Gc CLASS 2258 82 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations, Certified to US standards. Class I, Division 2, Groups A, B, C and D Class 1, Zone 2, AEx na IIC T6..T1 Gc CE134 Accelerometer PNR 444-134-000-YY5 to YY9, YY depends on the connector type and cable length (YY = 00 to 99) Entity parameters: U 28V, P 224 mw Note Sensor Operating Temperature: -70 C to +350 C Cable Operating Temperature: -54 C to +260 C Conditioner Operating Temperature: -54 C to +125 C Temperature classes depend on operating temperature of conditioner, cable and sensor: Part T6 T5 T4 T3 T2 T1 Sensor +80 C +95 C +130 C +195 C +290 C +350 C Cable +80 C +95 C +130 C +195 C +260 C -- Conditioner +65 C +80 C +115 C +125 C -- -- CLASS 2258 83 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non Incendive Systems For Hazardous Locations, Certified to US standards. Class I, Division 1 Groups A, B, C and D Class 1, Zone 0, AEx ia IIC T6..T1 Ga CE134 Accelerometer PNR 444-134-000-YY5 to YY9, YY depends on the connector type and cable length (YY = 00 to 99) Entity parameters: Ui : 28V; Ii : 100mA; Pi : 700mW; Ci : 0; Li : 0 DQD 507 Rev. 2012-05-22 Page 1 DQD 507 Rev. 2012-05-22 Page 2 2 CCSAUS certificate 70034691
Certificate: 70034691 Project: 70034691 Master Contract: 175074 Date Issued: September 22, 2015 Certificate: 70034691 Project: 70034691 Master Contract: 175074 Date Issued: September 22, 2015 APPLICABLE REQUIREMENTS Marking is engraved on product metallic body. CAN/CSA-C22.2 No. 0-10 August 2011 General requirements Canadian Electrical Code, Part II CAN/CSA-C22.2 No. 61010-1-12 (May 2012) CAN/CSA-C22.2 No. 60079-0:11 (December 2011) CAN/CSA-C22.2 No. 60079-11:14 (February 2014) CAN/CSA-C22.2 No. 60079-15:12 Third Edition Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 1: General Requirements Explosive atmospheres Part 0: Equipment General requirements Explosive atmospheres Part 11: Equipment protection by intrinsic safety i Electrical apparatus for explosive gas atmospheres Part 15 CAN/CSA-C22.2 No. 157-92 2012 Intrinsically Safe and Non- Incendive Equipment for use in Hazardous location CAN/CSA-C22.2 No.213-M1987-2013 Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations ANSI/UL 60079-0-2013 Explosive atmospheres Sixth Edition (July 26, 2013) Part 0: Equipment General requirements ANSI/UL 60079-15-2013 Explosive Atmospheres Part 15: Type of protection n ANSI/UL 60079-11 2013 Explosive Atmospheres Sixth Edition (September 6, 2013) Part 11: Equipment Protection by Intrinsic Safety i ANSI/UL 61010-1-2012 Safety Requirements for Electrical Equipment for Third Edition (May 11, 2012) Measurement, Control, and Laboratory Use Part 1: General Requirements ANSI/UL 913 2013 Intrinsically Safe Apparatus and Associated Apparatus for Use Eighth Edition in Class I, II and III, Division I, Hazardous Locations ANSI/ISA-12.12.01-2013 Non-Incendive Electrical Equipment for Use in Class I and II, MARKINGS Division 2 and Class III, Divisions 1 and 2 Hazardous Locations Manufacturer s name : MEGGITT SA Model Number: As specified in the products section. Marking as specified in the products section. Note to say Refer dwg PZ8584, Refer drawing PZ8585 (for Electrical Entity parameters: As specified in the products section.) Serial Number and Manufacturing date in MMYY format. COC number : CSA 700034691 The CSA Mark with C and US indicators as shown on the Certificate of Conformity. Note: See Instructions for ambient temperature range and warnings. The manufacturer is required to apply the following markings: Products shall be marked with the markings specified by the particular product standard. Products certified for Canada shall have all Caution and Warning markings in both English and French. Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where applicable, in accordance with the requirements of those authorities. The products listed are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US (indicating that products have been manufactured to the requirements of both Canadian and U.S. Standards) or with adjacent indicator 'US' for US only or without either indicator for Canada only. DQD 507 Rev. 2012-05-22 Page 3 DQD 507 Rev. 2012-05-22 Page 4 CCSAUS certificate 70034691 3
Supplement to Certificate of Compliance Certificate: 70034691 Master Contract: 175074 The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Product Certification History Project Date Description 70034691 September 22, 2015 Original Certification of PNR 444-134-000-YY5 to YY9 DQD 507 Rev. 2012-05-22 Page 1 4 CCSAUS certificate 70034691
CCSAUS certificate 70034691 5
6 CCSAUS certificate 70034691