6 1-1 3 8 5 6 1 6 2 1 4 1 8 6 8 kg/cm2 11 psi 1 16 1 1 1 6 1 ASSE 117 VAL VE -1 CO. 3 6 8 5 1 THEMOSTATIC T YPE TM AN STON 1 1.I. U.S.A. 6 1-1 6 3 8 1 5 1 1 6 1-1 6 3 8 5 1 1 1 H C Bulletin M-115Z August, 18 MEGATON MODEL 2NB-LF, 3NB-LF, 4NB-LF, 5NB-LF NEXT GENEATION MANIFOLD SYSTEMS TM-5B-LF, 8B-LF, 9B-LF, 15B-LF! WANING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer. For more information, go to www.p65warnings.ca.gov DOMESTIC OUTLET TEST/SETUP CONNECTION ETUN LINE FOM BUILDING LEO NAD ETUN LINE TO WATE SOUCE INLET INLET 1. Type TM manifold systems are factory pre-assembled and tested and include large and small thermostatic water mixing valves which function as a system to meet both high and low demand for tempered water. 2. System should be installed at a location where it can easily be cleaned, adjusted or repaired. 3. System supplies must be connected as shown (Hot-left, Cold-right). Exercise caution when soldering. 4. Flush pipes thoroughly after system has been connected. 5. efer to page 3 & 4 & 5 of this bulletin for correct Setup Instructions. Maximum Operating Pressure 125PSI (862 KPA) for Hot and Cold Water. CAUTION All thermostatic water mixing valves have limitations. They will not provide the desired accuracy outside of their flow capacity range. Consult the capacity chart on page 9. Minimum flow must be no less than as shown. EMEMBE! THIS IS A CONTOL SYSTEM WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS (SEE MAINTENANCE GUIDE AND ECOD MG-1). 136 Elmwood Avenue, Cranston, I 291 USA Phone: 1.461.1 Fax: 1.941.531 Email: info@leonardvalve.com Web Site: http://www.leonardvalve.com
117 ASSE ADJUSTMENT AND SEVICE Leonard Type TM Thermostatic Water Mixing Valves are simple in design and may be easily cleaned, adjusted and repaired. If the installation is accessible, servicing may be completed without disconnecting the valves. NOTE: High Low Manifold Systems include Thermostatic Water Mixing Valves, which must be regularly maintained to provide best performance. Frequency of cleaning depends on quality of local water conditions and usage. See Maintenance Guide and ecord MG-1. WANING These mixing valves are equipped with an adjustable high temperature limit stop factory set at approximately 1 (49) with an incoming hot water supply temperature of 15 (65.5). If the hot water supply temperature of the job is greater than 15 (65.5), the valves when turned to full will deliver water in excess of 1 (49) and the limit stops MUST BE ESET BY THE INSTALLE! TO ESET ADJUSTABLE HIGH TEMPEATUE LIMIT STOP: Serial# s starting with 52, 82, 92, 152 THEMOSTATIC POINTE SCEW TM-26 FINE ADJUSTMENT SCEW C H POINTE SNAP CAP STOP SCEW LT SET SCEW 1. Loosen LT set screw. 2. emove SNAP CAP, SCEW & WASHE. emove POINTE. 3. Temporarily place POINTE on the spline rod, turn IGHT for warmer temperature, turn LEFT for cooler temperature. When valve is delivering warmest temperature desired, remove the pointer. 4. eplace POINTE on the spline rod so that its IGHT edge is resting against the STOP SCEW located on the IGHT SIDE OF THE COVE. 5. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE ESET AND ECHECKED EACH TIME HANDLE IS EMOVED. POINTE STOP LT WEB (EST STOP AGAINST SCEW) SET SCEW 1. Loosen LT SET SCEW, remove POINTE SCEW. 2. Adjust POINTE to maximum desired temperature. 3. emove POINTE, replace POINTE on spline rod with STOP (which is cast into the underside on the pointer), resting against the BOTTOM side of the WEB on the FINE ADJUSTMENT SCEW. 4. If fine adjustment is needed, adjust FINE ADJUSTMENT SCEW on the cover, loosen for hotter or tighten for cooler temperature. 5. eplace POINTE and check temperature, if set to desired temperature replace POINTE SCEW, and tighten LT SET SCEW. 6. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE ESET AND ECHECKED EACH TIME HANDLE IS EMOVED. IMPOTANT! BOTH MIXING VALVES MUST BE SET AT THE SAME OPEATING TEMPEATUE. SEE PAGES: 7 & 8 FO COMPLETE PATS BEAKDOWN Check for significant variations in outlet flow. Thermostatic valves will NOT provide the desired accuracy outside of their flow capacity range. Minimum flows must be no less than shown (see Flow Capacities, page 9). If installed on a recirculated hot water system, make certain the valve is piped according to Leonard equired Piping Method (see page 4 & 5). EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS. (SEE MAINTENANCE GUIDE AND ECOD, MG-1). 2
6 1-1 3 8 5 6 1 6 2 1 4 1 8 6 8 psi kg/cm2 11 1 16 1 1 1 6 1 ASSE 117-1 CO. 6 3 8 5 1 THEMOSTATIC TYPE TM US. Patent 77 & 3,61,195 3.1 52,7 6 1 1.I. 6 1-1 6 3 8 1 5 1 1 6 1-1 6 3 8 5 1 1 1 SETUP INSTUCTIONS DOMESTIC OUTLET THEMOMETE TEST/SETUP CONNECTION PESSUE GAUGE ETUN LINE FOM BUILDING V1 V2 LAGE VALVE LEO NAD VAL VE AN STON U.S.A. SMALL VALVE H C ETUN LINE TO WATE SOUCE INLET INLET 1. High-low Unit MUST be piped to correct piping method (see pages 4 &5). 2. Make sure hot and cold supplies to this assembly are operating. The temperature of the hot water source must be properly set and maintained. 3. The circulator (if used) must be turned OFF before setup. 4. Turn on enough fixtures for a flow of at least * downstream from this system. Make sure each fixture is set to deliver full water. *8 GPM (3 l/min.) if TM valve is a TM-5 (Serial #52) *13 GPM (45 l/min.) if TM valve is a TM-8 (Serial #82) *13 GPM (45 l/min.) if TM valve is a TM-9 (Serial #92) *18 GPM (68 l/min.) if TM valve is a TM-15 (Serial #152) 5. Close outlet Valve V1 at the smaller Type TM Valve. 6. Make sure valve V2 at the large Type TM Valve is in the full open position. 7. Set outlet temperature of the large Type TM Valve to the required level. 8. Open outlet Valve V1 at the small TM Valve. 9. Shut outlet Valve V2 at the large TM Valve. 1.Turn on enough fixtures for a flow at least 2 GPM downstream from this system. Make sure each fixture is set to deliver full water. 11.Set outlet temperature of the small TM Valve to the same temperature as step 7. 12.Open outlet Valve V2. System is operational. 13.IMPOTANT!! See pages 4 & 5 to balance recirculation system. 3
6 1-1 8 5 1 1 1 6 4 1-1 6 3 8 5 1 THEMOSTATIC TYPE TM 1 1 2 6 1-1 8 1 5 1 1 4 2 6 8 3-1 6 1 H C 1 1 METHOD #2, FO METHOD #5 (1 or larger return line) see page 5 DOMESTIC TEMPEED WATE HIGH TEMP. WATE WATE SOUCE HEAT TAP BALANCING VALVE DOMESTIC ECICULATED WATE HIGH TEMPEATUE ECICULATED WATE SUPPLY POCEDUE TO BALANCE ECICULATION SYSTEM 1. Before any attempt is made to adjust this system, be sure the temperature of the hot water at the source is properly set and maintained. 2. Be sure system is piped correctly. 3. Turn circulator off, set mixing valve to the desired temperature, (see page 3). 4. Shut off all fixtures. Note: At this point, be sure NO water is being drawn through any fixture until the temperature in the recirculated line has been set. 5. Open the ball valve fully and start the circulator. 6. Observe the temperature until it stabilizes. 7. Adjust 37 AV counter clockwise (coming out of valve body) slightly if warmer temperature is desired or clockwise (going into valve body) if cooler water is desired. Allow to stabilize. epeat until the desired recirculated temperature is set. 8. Note: If system has a 1 return line or larger (circuit setter instead of AV) see page 5 for set-up. EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS (SEE MAINTENANCE GUIDE AND ECOD, MG-1). 4
6 8 1 1 1 6 8 1 8 1 1 1 6 8 1 1 METHOD #5 DOMESTIC TEMPEED WATE FIXTUES HIGH TEMPEATUE SUPPLY BALANCING VALVE #2 WATE SOUCE HEAT TAP (OPTIONAL) BALANCING VALVE #1 SUPPLY POCEDUE TO BALANCE CICULATION SYSTEM 1. Make sure no water is being drawn in the building, open balancing valve #1 approximately half way and start the circulator. Keep balancing valve #2 closed at this time. 2. Observe temperature until it stabilizes. 3. Close balancing valve #1 slightly if temperature is too hot, or open it slightly if temperature is to cold. Allow temperature to stabilize, repeat until desired circulation temperature is set. 4. If unable to reach desired temperature with balancing valve #1 in the full open position, open balancing valve #2 in very small increments (I.E. 1/16, 1/8, 3/16, ¼, etc.) until desired temperature is achieved. 5 C HIGH TEMPEATUE ETUN
ASSE 117 INSTUCTIONS FO SEVICING LAGE TM VALVE POINTE DIVING BALL BALL SOCKET INSTUCTIONS FO SEVICING SMALLE TM 26 VALVE POINTE SCEW FINE ADJUSTMENT SCEW THEMOSTAT GOUP FLANGE PACKING 1. Shut off hot and cold supplies to this valve, loosen LT set screw, remove snap cap, screw and washer, friction spring, remove pointer. 2. emove, cover screws and cover, to which the thermostat group is attached. WEB POINTE (EST STOP AGAINST SCEW) STOP LT SET SCEW 1. Loosen LT set set screw. 2. emove pointer screw, and pointer. 3. Turn off hot and cold supplies at screwdriver checkstops. emove M-2C cover screws to release cover and thermostatic control assembly. THIMBLE CHECK NUT POT SLEEVE POT SLEEVE NUT 3. To clean port sleeve assembly (the thimble must slide freely on the port sleeve): unscrew the check nut as far as it will go, then screw the port sleeve nut into the base. The port sleeve and thimble may then be lifted out. 4. Clean with a non-corrosive cleaning solution. DO NOT USE ABASIVES! The port sleeve should be reassembled in the valve with the shoulder to the left. 5. To clean thermostat group brush in a non-corrosive cleaning solution. 6. When reassembling, make sure driving ball of thermostat group engages the ball socket of the port sleeve assembly. 4. To remove bridge assembly, TM-28-1-8B, remove pointer rod nut (MU-1B) and pull bridge assembly off control rod. 5. To clean submerge bridge assembly in clean water or non-corrosive cleaning solution. DO NOT USE ABASIVES! Be certain thimble moves freely on port sleeve. Note! Driving ball must engage slot in thimble when reassembling. 6. To clean thermostat group, loosen gland nut and remove cover. Brush in a non-corrosive cleaning solution. 7. To disassemble bridge assembly, see drawing next page (remove TM25-3A holder nuts with screwdriver in slots provided). TOUBLESHOOTING INSTUCTIONS Note: Provide valve serial number when ordering parts for either valve! Large Valve (52,82) Large Valve (92) Large Valve (125) Small Valve TM-26 PACKING & GASKETS 1. Leak between valve cover and base. epair Kit 1/5Y epair Kit 1/5Y epair Kit 1/125Y (125) epair Kit 1/26 (Packings & Gaskets) POT SLEEVE /BIDGE ASSEMBLY THEMOSTAT GOUP 2. Valve delivers either all hot or all cold water, or will not mix consistently. 3. After cleaning or replacing port sleeve/bridge assembly, valve performance is not consistent. epair Kit /5 epair Kit /5 or TGM-2/5 epair Kit /9 epair Kit /9 or TGM-2/5 epair Kit /125 epair Kit /125 or TGM-2/125 epair Kit /28 or TM-28-1-8B (bridge assembly) KIT#/28 (rebuilding kit) Or TM28-G2 (thermostat group) CHECKSTOPS 4. Hot water by-pass into cold line (or cold into hot). 5. Supplies cannot be shut off completely. Supplies leak at checkstop bonnets. epair Kit 2/5Y epair Kit 2/5Y epair Kit 2/5Y epair Kit 4/M (Checkstop Kit) See pages 7 & 8 for parts Breakdowns 6
TM VALVE PATS 1 INLET & LAGE 57-L SNAP CAP TM-25C POINTE TM-15B/5 (52, 82, 92) Serial No's TM-15B/125 (152) Serial No's COVE TM-25D STOP TGM-2/5 (52, 82, 92) Serial No's TGM-2/125 (152) Serial No's THEMOSTAT GOUP TM-8 COIL SLEEVE STUD O'ING (2) THEMOSTATIC C H TM-29/29A POINTE SCEW W/WASHE 3 FICTION SPING TM-16 COVE SCEWS TM-28A POINTE OD TM-16A/5 (52, 82, 92) Serial No's TM-16A/125 (152) Serial No's DIAL PLATE TM-21/ 5 (52, 82, 92) Serial No's TM-21/125 (152) Serial No's FLANGE PACKING CHECKSTOP PATS TM-3/5 (52, 82, 92) Serial No's TM-3/125 (152) Serial No's POT SLEEVE NUT ASSY TGM-1/5 (52, 82) Serial No's TGM-1/9 (9) Serial No's TGM-1/125 (152) Serial No's POT SLEEVE ASSY EPAI KITS LF 3 LOWE STEM & PACKING UPPE STEM MU-4A 5 PACKING EPAI KIT 1/5Y 5,8,9 PACKINGS & GASKETS (52, 82, 92) EPAI KIT 1/125Y PACKINGS & GASKETS (125) TM21/5 (52, 82, 92) Serial No's TM21/125 (152) Serial No's FLANGE PKG 1529 SPING YELLOW O'ING 13 SCEEN TM-2 BONNET 14 CAP PACKING **=2 EA. O'ING (4) 1529 ** SPING 3** YELLOW LOWE STEM & PACKING 13** SCEEN 5** BONNET PKG. 14** CAP PACKING LOCK-TYPE POINTE 6 STAINE CAP EPAI KIT /5 TM-5,8 EBUILDING KIT (52, 82) EPAI KIT /9 TM-9 EBUILDING KIT (92) EPAI KIT /125 TM-15A EBUILDING KIT (125) TM-3/5 (52, 82, 92) Serial No's TM-3/125 (152) Serial No's POT SLEEVE NUT ASSY. TM-28A POINTE OD O'ING (2) TM21/5 (52, 82, 92) Serial No's TM21/125 (152) Serial No's FLANGE PKG TM-36 POINTE SET SCEW TGM-1/5 (52, 82) Serial No's TGM-1/9 (92) Serial No's TGM-1/125 (152) Serial No's POT SLEEVE ASSY TGM-2/5 (52, 82, 92) Serial No's TGM-2/125 (152) Serial No's THEMOSTAT GOUP TM-8 COIL SLEEVE STUD EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS. SEE MAINTENANCE GUIDE AND ECOD MG-1. NOTE: AFTE INSTALLING NEW PATS IT WILL BE NECESSAY TO ESET THE ADJUSTABLE HIGH TEMPEATUE LIMIT STOP ON EACH VALVE (SEE PAGE 2). EPAI KIT 2/5Y CHECKSTOP KIT 2 EA: 3 LOWE STEM & PACKING O'ING 13 SCEEN 1529 14 SPING YELLOW CAP PACKING 5 BONNET PKG. 7
TM-26 VALVE PATS (BOTTOM VALVE) 75 POINTE SCEW 691 LT SET SCEW 3313 DIAL PLATE 57-D F GLAND NUT M-1C F/CP COVE M-3C COVE GASKET M-2C COVE SCEWS F/CP-CHOOSE ONE F OUGH FINISH CP CHOME FINISH 7628 POINTE TM28-1-8B BIDGE ASSEMBLY TM28-G2 THEMOSTAT GOUP MU-4C GLAND PACKING MU-1B POINTE OD NUT (2 EQ'D) TM25-3 TM25-3A P.S. HOLDE P.S. HOLDE NUT (2 EQ'D) (2 EQ'D) TGM-1/28 POT SLEEVE TM28-6B ASSEMBLY HOLDE NUT O'ING (2 EQ'D) TM25-5 BIDGE TM25-3B P.S. PACKING (2 EQ'D) CHECKSTOP PATS M-3A BONNET PACKING M-9A CHECK SPING MU-4A F/CP UPPE STEM AND PACKING M-2A F/CP CHECK BONNET EPAI KITS KIT 1/26 PACKINGS & GASKETS MU-4C GLAND PKG. (2 EACH) M-3A BONNET PKG. (2 EACH) M-3C COVE GASKET M-9A (2 EACH) CHECK SPING TM28-6B HOLDE NUT O'ING (2 EACH) M-6A LOWE STEM & PKG. (2 EACH) O'ING (2 EACH) CHECKSTOPS M-6A LOWE STEM & PACKING UPPE STEM O'ING KIT /28 EBUILDING KIT M-3C COVE GASKET TM28-1-12B THEMOSTATIC CONTOL ASSEMBLY KIT 4/M CHECKSTOP KIT 2 EACH: M-6A LOWE STEM & PACKING UPPE STEM O'ING M-3A BONNET PKG. M-9A CHECK SPING EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS (SEE MAINTENANCE GUIDE AND ECOD). NOTE: AFTE INSTALLING NEW PATS IT WILL BE NECESSAY TO ESET THE ADJUSTABLE HIGH TEMPEATUE LIMIT STOP ON EACH VALVE (SEE PAGE 2). 8
FLOW CAPACITIES MODEL IN OUT MINIMUM FLOW (GPM) (l/min),3 SYSTEM PESSUE DOP (PSIG) 5 1 15 25 3 35.7.97 1.4 1.7 2.1 2.4 2.8 45 5 3.1 3.4 PSI BA TM-5B 3/4" 1" 1. (3.7) 19 72 29 11 38 144 45 17 51 193 56 212 62 235 68 257 72 272 75 284 GPM l/min TM-8B 1" 1 1/4" 1. (3.7) 26 48 58 63 98 151 182 2 238 68 257 74 79 84 89 28 299 318 337 GPM l/min TM-9B 1 1/4" 1 1/4" 1. (3.7) 33 98 47 151 56 212 63 68 82 85 92 13 115 GPM 2 238 257 28 299 318 337 l/min TM-15B 1 1/4" 1 1/2" 1. (3.7) 48 182 65 246 8 95 33 36 112 424 1 454 13 1 158 492 53 598 165 GPM 625 l/min LIMITED WAANTY Leonard Valve Company warrants the original purchaser that products manufactured by them (not by others) will be free from defects in materials and workmanship under normal conditions of use, when properly installed and maintained in accordance with Leonard Valve Company's instructions, for a period of one year from date of shipment. During this period the Leonard Valve Company will at its option repair or replace any product, or part thereof, which shall be returned, freight prepaid, to the Leonard factory and determined by Leonard to be defective in materials or workmanship. There are no warranties, express or implied, which extend beyond the description contained herein. There are no implied warranties of merchantability or of fitness for a particular purpose. In no event will Leonard be liable for labor or incidental or consequential damages. Any alteration or improper installation or use of the product will void this limited warranty 18 Leonard Valve Company Printed in USA 9