5-1 8 1 1 2 4 8 6 8 kg/cm 2 11 psi 1 1 1 LEO NAD 17 VAL VE - C O. THEMOSTATIC PE TM 8 5 1 CAN STON 1.I. U.S.A. - 8 1 5 1-8 5 1 1 H C Bulletin M-11Z January 14 MEGATON MODEL 2N, 3N, 4N, 5N HIGH-LOW MANIFOLD SYSTEMS TM-5, TM-8, TM-9, TM-15A TM-5-LF, TM-8-LF, TM-9-LF, TM-15A-LF IMPOTANT! Provide serial numbers for both valves when ordering parts!! Small valve manufactured after July 7 starting ti with serial # TM39272 DOMESTIC OUTLET TEST/SETUP CONNECTION ETUN LINE FOM BUILDING ETUN LINE TO WATE SOUCE HOT COLD INLET INLET MEGATON 2N THU 4N SHOWN 1. Type TM manifold systems are factory pre-assembled and tested and include large and small thermostatic water mixing valves which function as a system to meet both high and low demand for tempered water. 2. System should be installed at a location where it can easily be cleaned, adjusted or repaired. 3. System supplies must be connected as shown (Hot-left, Cold-right). Exercise caution when soldering. 4. Flush pipes thoroughly after system has been connected. 5. efer to page 3 & 4 & 5 of this bulletin for correct Setup Instructions. Maximum Operating Pressure 125PSI (8 KPA) for Hot and Cold Water. CAUTION All thermostatic water mixing valves have limitations. They will not provide the desired accuracy outside of their flow capacity range. Consult the capacity chart on page 9. Minimum flow must be no less than as shown. EMEMBE! THIS IS A CONTOL SYSTEM WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS (SEE MAINTENANCE GUIDE AND ECOD MG-). 13 Elmwood Avenue, Cranston, I 29 USA Phone: 1.461. Fax: 1.941.53 Email: info@leonardvalve.com Web Site: http://www.leonardvalve.com
17 ASSE ADJUSTMENT AND SEVICE Leonard Type TM Thermostatic Water Mixing Valves are simple in design and may be easily cleaned, adjusted and repaired. If the installation is accessible, servicing may be completed without disconnecting the valves. NOTE: High Low Manifold Systems include Thermostatic Water Mixing Valves, which must be regularly maintained to provide best performance. Frequency of cleaning depends on quality of local water conditions and usage. See Maintenance Guide and ecord MG-. WANING These mixing valves are equipped with an adjustable high temperature limit stop factory set at approximately 1 (49) with an incoming hot water supply temperature of 15 (65.5). If the hot water supply temperature of the job is greater than 15 (65.5), the valves when turned to full HOT will deliver water in excess of 1 (49) and, the limit stops MUST BE ESET BY THE INSTALLE! TO ESET ADJUSTABLE HIGH TEMPEATUE LIMIT STOP: Serial # s starting with 52, 82, 92, 152 TM- THEMOSTATIC POINTE SCEW HOT COLD FINE ADJUSTMENT SCEW C H STOP POINTE SCEW SNAP LT CAP SET SCEW 1. Loosen LT set screw. 2. emove SNAP CAP, SCEW & WASHE. emove POINTE. 3. Temporarily place POINTE on the spline rod, turn IGHT for warmer temperature, turn LEFT for cooler temperature. When valve is delivering warmest temperature desired, remove the pointer. 4. eplace POINTE on the spline rod so that its IGHT edge is resting against the STOP SCEW located on the IGHT SIDE OF THE COVE. 5. The new maximum temperature has now been set. Test this temperature with thermometer. 6. e-assemble pointer to valve with snap cap, screw and washer. * LIMIT STOP MUST BE ESET AND ECHECKED EACH TIME HANDLE IS EMOVED. POINTE STOP LT SET SCEW WEB (EST STOP AGAINST SCEW) 1. Loosen LT SET SCEW, remove POINTE SCEW. 2. Adjust POINTE to maximum desired temperature. 3. emove POINTE, replace POINTE on spline rod with STOP (which is cast into the underside on the pointer), resting against the BOTTOM side of the WEB on the FINE ADJUSTMENT SCEW. 4. If fine adjustment is needed, adjust FINE ADJUSTMENT SCEW on the cover, loosen for hotter or tighten for cooler temperature. 5. eplace POINTE and check temperature, if set to desired temperature replace POINTE SCEW, and tighten LT SET SCEW. 6. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE ESET AND ECHECKED EACH TIME HANDLE IS EMOVED. IMPOTANT! BOTH MIXING VALVES MUST BE SET AT THE SAME OPEATING TEMPEATUE. SEE PAGES: 8 & 9 FO COMPLETE PATS BEAKDOWN Check for significant ifi variations iti in outlet t flow. Thermostatic ti valves will NOT provide the desired d accuracy outside tid of their flow capacity range. Minimum flows must be no less than shown (see Flow Capacities, page ). EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS. (SEE MAINTENANCE GUIDE AND ECOD, MG-). 2
8 5-1 1 LEO 2 17 TM - 8 6 4 8 ps i kg/cm 2 11 1 8 1 1 5 THEMOSTATIC U S. P ate n t 77 & 3, 61,1 95 3.1 52,76 CO. CAN 1 STON 1.I. - 8 1 5 1-8 5 1 1 SETUP INSTUCTIONS DOMESTIC OUTLET THEMOMETE TEST/SETUP CONNECTION ETUN LINE FOM BUILDING PESSUE GAUGE V2 V1 LAGE VALVE SMALL VALVE NAD VAL VE U.S.A. ETUN LINE TO WATE SOUCE HOT INLET COLD INLET MEGATON 5N SHOWN 1. TM-186 High-low Unit MUST be piped to correct piping method (see pages 4 &5). 2. Make sure hot and cold supplies to this assembly are operating. The temperature of the hot water source must be properly set and maintained. 3. The circulator (if used) must be turned OFF before setup. 4. Turn on enough fixtures for a flow of at least * downstream from this system. Make sure each fixture is set to deliver full HOT water. *8 GPM ( l/min.) if TM valve is a TM-5 (Serial #52) *12 GPM (45 l/min.) if TM valve is a TM-8 (Serial #82) *12 GPM (45 l/min.) if TM valve is a TM-9 (Serial #92) *18 GPM (68 l/min.) if TM valve is a TM-15 (Serial #152) 5. Close outlet Valve V1 at the smaller Type TM Valve. 6. Make sure valve V2 at the large Type TM Valve is in the full open position. 7. Set outlet temperature of the large Type TM Valve to the required level. 8. Open outlet Valve V1 at the small TM Valve. 9. Shut outlet Valve V2 at the large TM Valve..Turn on enough fixtures for a flow at least 2 GPM downstream from this system. Make sure each fixture is set to dli deliver full ll HOT water. 11.Set outlet temperature of the small TM Valve to the same temperature as step 7. 12.Open outlet Valve V2. System is operational. 13.IMPOTANT!! See pages 4 & 5 to balance recirculation system. 3
- 8 5 1 1 LEO NAD 2 4 17 VAL VE TM CO. 8 6 8 kg/ cm 2 11 psi 1 8 1 1 5 - THEMOSTATIC CAN 1 STON 1.I. U.S.A. - 8 1 5 1-8 1 1 EQUIED METHOD OF PIPING (ECICULATED DOMESTIC WATE SYSTEMS) DOMESTIC TEMPEED WATE HIGH TEMP. WATE HOT WATE SOUCE 5 HEAT TAP BALANCING VALVE DOMESTIC ECICULATED WATE HIGH TEMPEATUE ECICULATED WATE COLD SUPPLY METHOD #2 SHOWN 1. MAKE SUE NO WATE IS BEING DAWN IN THE BUILDING, STAT CICULATO. 2. OBSEVE TEMPEATUE UNTIL IT STABILIZES. 3A.- BALANCING VALVE - CLOSE BALANCING VALVE SLIGHTLY IF TEMPEATUE IS TOO HOT, O OPEN IT SLIGHTLY IF TEMPEATUE IS TOO COLD AND ALLOW TEMPEATUE TO STABILIZE. EPEAT UNTIL DESIED ECICULATED TEMPEATUE IS SET. 3B.- AV TUN HANDLE ON AUTOMATIC ETUN VALVE TO COOLE SLIGHTLY IF TEMPEATUE IS TOO HOT, O TUN HANDLE TO WAME SLIGHTLY IF TEMPEATUE IS TOO COLD AND ALLOW TEMPEATUE TO STABILIZE. EPEAT UNTIL DESIED ECICULATED TEMPEATUE IS SET. EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS (SEE MAINTENANCE GUIDE AND ECOD, MG-). 4
MODEL 3/37AV Check dial plate on knob for model # ETAINING CLIP KNOB STEM ASSEMBLY O'ING COVE O'ING STEM ASSEMBLY SHUTTLE ASSEMBLY SCEW DIAL PLATE KNOB SET SCEW COVE DISMANTLING & CLEANING 1. Shut off hot and cold water to the valve as well as the valve outlet port. 2. Loosen lock screw on side of knob with 5/64 allen wrench. 3. emove the knob screw on top of knob. 4. emove temperature adjustment knob. 5. emove valve cover, which includes the stem assembly. 6. The shuttle assembly can now be removed, cleaned and inspected. Besuretocheckthe condition of the shuttle o-ring and replace if necessary. 7. Lubricate the shuttle o-ring before installing the shuttle assembly. 8. Install the cover assembly including o-ring back onto valve and tighten. 9. eplace knob and knob screw.. Valve temperature must be reset after any repairs or cleaning!! SHUTTLE O'ING ETUN SPING TOUBLESHOOTING 1. Leaking water under knob, order gasket kit, replace stem assembly o-ring. emove knob screw and knob, remove retaining clip, thread out the stem assembly and replace o-ring. Lubricate o-ring, thread stem into cover, replace retaining ring, knob and screw. Valve temperature must be reset after any repairs or cleaning!! 2. Leaking water between cover and body, order gasket kit, replace cover o-ring. emove knob screw and knob and remove valve cover and replace o-ring. eplace valve cover, knob and knob screw. Valve temperature must be reset after any repairs or cleaning!! 3. Valve not controlling temperature even after cleaning, order complete rebuild kit. emove knob screw and knob and remove valve cover. eplace shuttle assembly and return spring being sure to lubricate shuttle o-ring. eplace valve cover, knob and knob screw. Valve temperature must be reset after any repairs or cleaning!! EPAI KITS MODEL 3 AV MODEL 37 AV Leaking water under knob. Leaking water between valve cover and body. Valve will not control temperature after cleaning. 1/ WX Gasket Kit 1/ WX Gasket Kit Shuttle o ring Shuttle o ring Stem assembly o ring Stem assembly o ring Cover o ring Cover o ring / WX Complete ebuild Kit Kit / 27/37 Complete ebuild eturn spring eturn spring Shuttle assembly Shuttle assembly Shuttle o ring Shuttle o ring Stem assembly o ring Stem assembly o ring Cover o ring Cover o ring 5
6-8 5 1 1 2 2 4 8 6 8 kg/cm 2 11 ps i LEON AD 1 1 1 1 LE O N AD 17 VAL V E - TM C O. 8 5 1 THE M OS TA TIC CA N STON 1.I. U.S.A. LEO NAD LE ONAD - 8 1 5 1-8 5 1 1 LE ONA D METHOD #4 CICULATED FLOWS BETWEEN 8-25 GPM DOMESTIC TEMPEED WATE HIGH TEMP. WATE BALANCING VALVE #2 BALANCING VALVE #1 HOT WATE SOUCE HEAT TAP DOMESTIC ECICULATED WATE COLD SUPPLY HIGH TEMPEATUE ECICULATED WATE POCEDUE TO BALANCE CICULATION SYSTEM 1. MAKE SUE NO WATE IS BEING DAWN IN THE BUILDING. OPEN BALANCING VALVE #1 APPOXIMATELY HALF WAY AND STAT CICULATO. KEEP BALANCE VALVE #2 CLOSED AT THIS TIME. 2. OBSEVE TEMPEATUE UNTIL IT STABILIZES. 3. CLOSE BALANCING VALVE #1 SLIGHTLY IF TEMPEATUE IS TOO HOT, O OPEN IT SLIGHTLY IF TEMPEATUE IS TOO COLD. ALLOW TEMPEATUE TO STABILIZE, EPEAT UNTIL DESIED CICULATION TEMPEATUE IS SET. 4. IF UNABLE TO EACH DESIED TEMPEATUE WITH VALVE #1 IN THE FULL OPEN POSITION, OPEN BALANCE VALVE #2 IN SMALL INCEMENTS (i.e. 1/8, ¼, 3/8, ETC) UNTIL DESIED TEMPEATUE IS ACHIEVED. METHOD #5 CICULATED FLOWS GEATE THAN 25 GPM DOMESTIC TEMPEED WATE BALANCING VALVE #2 HIGH TEMP. WATE BALANCING VALVE #1 HOT WATE SOUCE HEAT TAP DOMESTIC ECICULATED W COLD SUPPLY HIGH TEMPEATUE ECICULATED WATE POCEDUE TO BALANCE CICULATION SYSTEM 1. MAKE SUE NO WATE IS BEING DAWN IN THE BUILDING. OPEN BALANCING VALVE #1 APPOXIMATELY HALF WAY AND STAT CICULATO. KEEP BALANCE VALVE #2 CLOSED AT THIS TIME. 2. OBSEVE TEMPEATUE UNTIL IT STABILIZES. 3. CLOSE BALANCING VALVE #1 SLIGHTLY IF TEMPEATUE IS TOO HOT, O OPEN IT SLIGHTLY IF TEMPEATUE IS TOO COLD. ALLOW TEMPEATUE TO STABILIZE, EPEAT UNTIL DESIED CICULATION TEMPEATUE IS SET. 4. IF UNABLE TO EACH DESIED TEMPEATUE WITH VALVE #1 IN THE FULL OPEN POSITION, OPEN BALANCE VALVE #2 IN SMALL INCEMENTS (i.e. 1/8, ¼, 3/8, ETC) UNTIL DESIED TEMPEATUE IS ACHIEVED. 6
INSTUCTIONS FO SEVICING LAGE TM VALVE POINTE DIVING BALL BALL SOCKET INSTUCTIONS FO SEVICING SMALLE TM VALVE POINTE SCEW LT SET SCEW M-2C COVE SCEWS THEMOSTAT GOUP FLANGE PACKING 1. Shut off hot and cold supplies to this valve, loosen LT set screw, remove snap cap, screw and washer, friction spring, remove pointer. 2. emove, cover screws and cover, to which the thermostat group is attached. POT SLEEVE POT SLEEVE NUT THIMBLE CHECK NUT 3. To clean port sleeve assembly (the thimble must slide freely on the port sleeve): unscrew the check nut as far as it will go, then screw the port sleeve nut into the base. The port sleeve and thimble may then be lifted out. 4. Clean with a non-corrosive cleaning solution. DO NOT USE ABASIVES! The port sleeve should be reassembled in the valve with the shoulder to the left. 5. To clean thermostat group brush in a non-corrosive cleaning solution. 6. When reassembling, make sure driving ball of thermostat group engages the ball socket of the port sleeve assembly. POINTE TEMPEATUE ADJUSTING SCEW TM-1-12B THEMOSTATIC CONTOL ASSEMBLY M-3C COVE GASKET 1. Turn off hot and cold supplies at screwdriver checkstops. emove handle. emove M-2C cover screws to release cover and thermostatic control assembly. MU-B POINTE OD NUT M-1-8B 1 BIDGE ASSY M-14B DIVING STUD POT SLEEVE THIMBLE M-5B P.S. HOLDE NUT 2. To remove bridge assembly, M-1-8B, remove pointer rod nut (MU-B) and pull bridge assembly off control rod. Do not misplace M-14B driving stud. 3. To clean submerge bridge assembly in clean water or non-corrosive cleaning solution. DO NOT USE ABASIVES! Be certain thimble moves freely on port sleeve. Note! Driving stud (M-14B) must engage slot in thimble when reassembling. 4. To clean cea thermostat group, goup, loosen gland ga nut and ad remove cover. Brush in a non-corrosive cleaning solution. 5. To disassemble bridge assembly, see drawing next page (remove M-5B holder nuts with screwdriver in slots provided). TOUBLESHOOTING INSTUCTIONS Note: Provide valve serial number when ordering parts for either valve! Large Valve (52,82) Large Valve (92) Large Valve (125) Small Valve PACKING & GASKETS 1. Leak between valve cover and base. epair Kit 1/5Y epair Kit 1/5Y epair Kit 1/125Y epair Kit 1/M (Packings & Gaskets) POT SLEEVE /BIDGE ASSEMBLY 2. Valve delivers either all hot or all cold water, or will not mix consistently. epair Kit TGM-1/5 /5 or epair Kit TGM-1/9 /9 or epair Kit /125 or TGM-1/125 epair Kit /M TM- (ebuilding Kit) or M-1-8B Bridge Assembly THEMOSTAT GOUP 3. After cleaning or replacing port sleeve/bridge assembly, valve performance is not consistent. epair Kit TGM-5 /5 or epair Kit TGM-5 /9 or epair Kit /125 or TGM-125 epair Kit /M (ebuilding Kit) or M-G2 Thermostat Group CHECKSTOPS 4. Hot water by-pass into cold line (or cold into hot). 5. Supplies cannot be shut off completely. Supplies leak at checkstop bonnets. epair Kit 2/5Y epair Kit 2/5Y epair Kit 2/5Y epair Kit 4/M (Checkstop Kit) 7
TM VALVE PATS 1 INLET & LAGE 57-L SNAP CAP TM-25C POINTE TM-15B/5 (52, 82, 92) Serial No's TM-15B/125 (152) Serial No's COVE TM-25D STOP TGM-2/5 (52, 82, 92) Serial No's TGM-2/125 (152) Serial No's THEMOSTAT GOUP TM-8 COIL SLEEVE STUD O'ING (2) THEMOSTATIC C H TM-29/29A POINTE SCEW W/WASHE FICTION SPING TM-16 COVE SCEWS TM-28A POINTE OD TM-16A/5 (52, 82, 92) Serial No's TM-16A/125 (152) Serial No's DIAL PLATE TM21/5 (52, 82, 92) Serial No's TM21/125 (152) Serial No's FLANGE PACKING TM-3/5 (52, 82, 92) Serial No's TM-3/125 (152) Serial No's POT SLEEVE NUT ASSY TGM-1/5 (52, 82) Serial No's TGM-1/9 (9) Serial No's TGM-1/125 (152) Serial No's POT SLEEVE ASSY CHECKSTOP PATS EPAI KITS 3 LOWE STEM & PACKING UPPE STEM 5 EPAI KIT 1/5Y 5,8,9 PACKINGS & GASKETS (52, 82, 92) PACKING EPAI KIT 1/125Y PACKINGS & GASKETS (125) TM21/5 (52, 82, 92) Serial No's TM21/125 (152) Serial No's FLANGE PKG 1529 O'ING SPING YELLOW 13 SCEEN 4/5 (52, 82, 92) Serial #'s 4/125 (152) Serial #'s #s SWIVEL 9/5 (52, 82, 92) Serial #'s 9/125 (152) Serial #'s SWIVEL NUT LOCK-TYPE POINTE TM-2 BONNET 14 CAP PACKING 6 STAINE CAP **=2 EA. O'ING (4) 1529 ** SPING 3** YELLOW LOWE STEM & PACKING TM-3/5 (52, 82, 92) Serial No's TM-3/125 (152) Serial No's POT SLEEVE NUT ASSY. O'ING (2) 13** SCEEN TM-28A POINTE OD 5** BONNET PKG. 14** CAP PACKING EPAI KIT /5 TM-5,8 EBUILDING KIT (52, 82) EPAI KIT /9 TM-9 EBUILDING KIT (92) EPAI KIT /125 TM-15A EBUILDING KIT (125) TM21/5 (52, 82, 92) Serial No's TM21/125 (152) Serial No's FLANGE PKG TGM-2/5 (52, 82, 92) Serial No's TGM-2/125 (152) Serial No's THEMOSTAT GOUP TM-36 POINTE SET SCEW EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS. SEE MAINTENANCE GUIDE AND ECOD. NOTE: AFTE INSTALLING NEW PATS, IT WILL BE NECESSAY TO ESET THE ADJUSTABLE HIGH TEMPEATUE LIMIT STOP ON EACH VALVE (SEE PAGE 2). 8 TGM-1/5 (52, 82) Serial No's TGM-1/9 (92) Serial No's TGM-1/125 (152) Serial No's POT SLEEVE ASSY EPAI KIT 2/5Y CHECKSTOP KIT 2 EA: 3 LOWE STEM & PACKING O'ING TM-8 COIL SLEEVE STUD 13 SCEEN 5 BONNET PKG. 1529 14 SPING YELLOW CAP PACKING
TM- VALVE PATS 75 POINTE SCEW 69 LT SET SCEW 57-D(F) GLAND NUT M-1C(F)(CP) COVE M-3C COVE GASKET 7628 POINTE M-14B DIVING STUD M--1-8B BIDGE ASSEMBLY MU-4C GLAND PACKING (2 EQ'D) M-5B P.S. HOLDE NUT (2 EQ'D) M-6B HOLDE NUT O'ING (2 EQ'D) M-1B BIDGE M-G2 THEMOSTAT GOUP DUA-trol MU-B POINTE OD NUT M-4B P.S. HOLDE (2 EQ'D) M-G1 POT SLEEVE ASSEMBLY M-3B P.S. PACKING (2 EQ'D) M-14B DIVING STUD CHECKSTOP PATS EPAI KITS CHECKSTOPS M-3A BONNET PACKING M-9A CHECK SPING M-6A LOWE STEM & PACKING MU-4A F/CP UPPE STEM AND PACKING UPPE STEM PKG. M-2A F/CP CHECK BONNET EPAI KIT 1/M PACKINGS & GASKETS M-3C MU-4C COVE GLAND PKG. (2 EACH) GASKET M-3A BONNET PKG. (2 EACH) M-9A SPING (2 EACH) M-6A LOWE STEM & PKG. (2 EACH) M-6B HOLDE NUT O'ING (2 EACH) EPAI KIT /M EBUILDING KIT M-3C COVE GASKET O'ING (2 EACH) M-1-12B THEMOSTATIC CONTOL ASSEMBLY EMEMBE! THIS IS A CONTOL DEVICE WHICH MUST BE CLEANED AND MAINTAINED ON A EGULA BASIS (SEE MAINTENANCE GUIDE AND ECOD, MG-). NOTE: AFTE INSTALLING NEW PATS IT WILL BE NECESSAY TO ESET THE ADJUSTABLE HIGH TEMPEATUE LIMIT STOP ON EACH VALVE (SEE PAGE 2). EPAI KIT 4/M EBUILDING KIT 2 EACH: M-6A LOWE STEM & PACKING UPPE STEM O'ING M-9A SPING M-3A BONNET PKG. 9
CICULATO/AQUASTAT CONTOL BOX 1/VAC 1. GFI switch is used to turn on power to circulator. 2. Green light on indicates pump and aquastat is in normal operation. 3. ed light on indicates that the circulator is not running due to temperature rise on aquastat. ALL WIING DONE BY END USE AND TO BE WIED BY A LICENSED ELECTICIAN GEEN LIGHT ED LIGHT WIING DIAGAM 1 VAC GFI PLUG AND SWITCH GEEN LIGHT ED LIGHT AQUASTAT CICULATO MODEL IN FLOW CAPACITIES OUT MINIMUM FLOW (GPM) (l/min),3 SYSTEM PESSUE DOP (PSIG) 5 15 25 35.7.97 1.4 1.7 2.1 2.4 2.8 45 5 3.1 3.4 PSI BA TM-5 3/4" 1" 1. (3.7) 19 72 29 1 38 144 45 17 51 193 56 212 62 235 68 257 72 272 75 284 GPM l/min TM-8 1" 1 1/4" 1. (3.7) 26 48 58 63 98 151 182 2 238 68 257 74 79 84 89 28 299 318 337 GPM l/min TM-9 1 1/4" 1 1/4" 1. (3.7) 33 98 47 151 56 212 63 68 82 85 92 3 115 GPM 2 238 257 28 299 318 337 l/min TM-15A 1 1/4" 1 1/2" 1. (3.7) 48 182 65 246 8 95 3 3 112 424 1 454 1 1 158 492 5 598 165 GPM 625 l/min LIMITED WAANTY Leonard Valve Company (hereinafter, Leonard ) warrants the original purchaser that products manufactured by Leonard will be free from defects in material or workmanship under normal conditions of use, when properly installed and maintained in accordance with Leonard s instructions, for a period of one year from the date of shipment. During this period, Leonard will at its option repair or replace any product, or part thereof, which shall be returned, freight prepaid, to the Leonard factory and determined by Leonard to be defective in materials or workmanship. Leonard provides no warranty, express or implied, which extends beyond the description contained herein. SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WAANTIES OF MECHANTABILITY O OF FITNESS FO A PATICULA PUPOSE. Nonetheless, some jurisdictions may not allow the disclaimer of certain implied warranties, in which case Leonard hereby limits such implied warranties to the duration of the limited warranty period contained herein. Some jurisdictions may not allow limitations on how long an implied warranty lasts, so the foregoing durational limitation may not apply to you. In no event will Leonard be liable for labor or incidental or consequential damages. Any alteration or improper p installation or use of this product will void this limited warranty. Ifany provision of this limited warranty is prohibited by law in the applicable jurisdiction, such provision shall be null and void, but the remainder of this limited warranty shall continue in full force and effect. 14 Leonard Valve Company Printed in USA