DRY AND PRE-ACTION SYSTEM INSPECTOR'S TEST DRAIN DETAIL

7

WET OR DRY SPRINKLER SYSTEM BRANCH PIPING FROM DETECTORS LOTED IN SPACE PROTECTED BY PREACTION SYSTEM TO FACP (BY EC) LOW (TROUBLE) SMOKE (ALARM) AIR FILLED SUPPLY PIPING MAINTENANCE AIR COMPRESSOR CONTROL WIRE INSTALLED IN CONDUIT (TYP.) AIR OUTLET ELECTRIC LOW AIR RELEASING ALARM SWITCH PANEL DRY PILOT ACTUATOR UL LISTED AND FM APPROVED DRY BARREL SPRINKLER HEAD ASSEMBLY. ROUTE TO INDIRECT DRAIN OR OUTSIDE OUTSIDE DETER: -5/" (SAME AS " SCHEDULE PIPE) RUBBER SEATED CHECK VALVE A DELUGE VALVE WITH DOUBLE INTERLOCK TRIM (TRIM NOT SHOWN) FOR "A" DIMENSION:. DETERMINE THE DISTANCE FROM THE FACE OF THE TEE TO THE BASE OF THE SPRINKLER. ROUND UP TO THE NET HIGHEST" INCREMENT BETWEEN " AND 7". GAUGE SUPERVISORY SWITCH ELECTRIC MANUAL CONTROL STATION GAUGE " DRAIN SS AIR TUBING (TYP) SOLENOID VALVE NORMALLY CLOSED. DOUBLE INTERLOCK PREACTION SYSTEM RISER DETAIL -5/8" ITEMS OF WORK OR SHOWN ON THE DRAWINGS ONLY, OR LLED FOR IN THE SPECIFITIONS ONLY, SHALL BE FURNISHED AND INSTALLED IN THE SAME MANNER AS IF THEY APPEARED ON BOTH THE DRAWINGS AND SPECIFITIONS. SHUT-OFF VALVE (GATE, BALL, ETC.) 5. INSTALL AND PIPING TO AVOID INTERFERENCE WITH THE OPERATION OR SERVICING AND MAINTENANCE OF. PIPING DEMOLITION PIPING CHECK VALVE REDUCING VALVE STRAINER ALL COSTS FOR CUTTING, PATCHING AND PAINTING OF WALLS, CEILINGS AND FLOORS TO ACCOMMO THE INSTALLATION OF WORK SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR UNLESS INDITED OTHERWISE. MATERIALS FOR RESTORATION OF SURFACES SHALL MATCH THE MATERIALS. ALL PHYSIL ATTRIBUTES OF AND DEVICES ARE BASED ON THOSE MANUFACTURERS LISTED IN THE SPECIFITIONS AND/OR THE SCHEDULES. THE CONTRACTOR IS RESPONSIBLE FOR ALL CHANGES BROUGHT ABOUT BY USE OF ITEMS BY OTHER MANUFACTURERS. THE ARCHITECT/ENGINEER HAS RESERVED THE RIGHT TO REJECT ITEMS BY OTHER MANUFACTURERS IF THOSE ITEMS DO NOT MATCH THE PHYSIL ATTRIBUTES OF THE MANUFACTURERS LISTED. P. COORDINATE CONNECTION OF SUPERVISORY SWITCHES, ES, AND OTHER SIMILAR DEVICES TO THE FIRE ALARM SYSTEM. GWB CEILING UPRIGHT SPRINKLER HEAD CLEAN AGENT NOZZLE SYSTEM SHALL BE A DESIGNATED DESIGN AS DEFINED IN THE SPECIFITIONS. SYSTEM TO BE HYDRAULILLY DESIGNED AND STAMPED BY A PROFESSIONAL ENGINEER LICENSED IN THE STATE OFNEW YORK. SPRINKLER HEAD TO REMAIN SPRINKLER HEAD TO BE REMOVED BACKFLOW PREVENTER (BFP) OS&Y VALVE " SCREW RESET TOOL GAUGE PILOT HOSE ADAPTER PILOT HOSE ADAPTER INSPECTORS TEST VALVE AND DRAIN. 7'-" AFF MAIMUM PENETRATE ETERIOR WALL " ABOVE FINISHED GRADE. TERMINATE PIPING AFTER ELBOW A MINIMUM OF 8" ABOVE FINISHED GRADE WITH STAINLESS STEEL BIRD SCREEN. MALFUNCTION SAFETY ASSEMBLY PILOT HOSE SWIVEL ADAPTOR RING-PROTECTION P POINT OF CONNECTION " LOTE INSPECTOR'S TEST VALVE IN AN ACCESSIBLE LOTION. PROVIDE LOCKABLE ACCESS PANEL FOR VALVE ACCESS WHERE INSTALLED IN FINISHED AREAS. POINT OF DISCONNECTION 5 ELBOW ETINGUISHING AGENT CYLINDER CIPHON TUBE FUSIBLE BULB SMOOTH BORE CORROSION RESISTANT OUTLET 75 PSI CYLINDER 5 LB PACITY SPLASH BLOCK CLAMP " GRADE ROUTE TO INTERIOR DRAIN OR ETERIOR AS INDITED ON DRAWINGS PROVIDE FUNNEL COVER ON FLOOR DRAIN FLOOR U.L. LISTED & F.M. APPROVED BRONZE UPRIGHT AUTOMATIC SPRINKLER HEAD " RISER VARIES TRENCH DRAIN, INDIRECT DRAIN OR FLOOR DRAIN W/ FUNNEL WITH MINIMUM " AIR GAP DRY PENDENT SPRINKLER HEAD PIPING HOSE 9 " / " 75 Essjay Road, Suite Williamsville, NY p:7.88.7 f:7.5.85 DIRECTION OF FLOW PROTECTION P RELEASE DEVICE PNEUMATIC ELBOW - TURNED DOWN 8. COMPLY WITH THE NEW YORKSTATE BUILDING CODES, NFPA AND OTHER APPLIBLE CODES. BRANCH CONNECTION - TOP ELBOW - TURNED UP 9. COURT STREET LITTLE VALLEY, NY 755 BRANCH CONNECTION - BOTTOM PIPES PENETRATING FIRE WALLS AND FLOORS SHALL BE FIRESTOPPED AS SPECIFIED. REFER TO THE ARCHITECTURAL DRAWINGS FOR FIRE WALL AND FLOOR LOTIONS. PRINT 8--8 7.. CHECK VALVE PIPING (BELOW GRADE) DRAWINGS DO NOT INDITE ALL OFFSETS, CHANGES IN ELEVATIONS, ETC. WHICH MAY BE REQUIRED. THE CONTRACTOR SHALL MAKE SUCH CHANGES IN PIPING AND LOTION OF, ETC. TO ACCOMMO WORK WITH THAT OF OTHER CONTRACTORS. TYPIL PLAIN BARREL DRY PENDENT SPRINKLER DETAIL RELEASE DEVICE ELECTRIC PIPING (ABOVE GRADE) THE PLANS ARE DIAGRAMMATIC AND INDITE ONLY THE SIZE AND GENERAL ARRANGEMENT OF PIPING AND. EACT LOTION OF ALL ELEMENTS SHALL BE DETERMINED AS WORK PROGRESSES, IN COOPERATION AND COORDINATION WITH THE WORK OF ALL OTHER TRADES. IT IS NOT INTENDED TO SHOW EVERY ITEM OF WORK OR MINOR PIECE OF, BUT THE CONTRACTOR SHALL FURNISH AND INSTALL WITHOUT ADDITIONAL REMUNERATION ANY COMPONENT NECESSARY TO COMPLETE THE SYSTEM IN ACCORDANCE WITH THE BEST PRACTICE OF THE TRADE.. SHUT-OFF VALVE (GATE) NORMALLY OPEN WET SUPPLY FROM SPRINKLER SYSTEM THIS LEGEND SHEET IS FOR CONTRACTOR REFERENCE ONLY. NOT ALL SYMBOLS AND/OR ABBREVIATIONS MAY APPLY TO THIS PARTICULAR PROJECT. ANY ADDITIONS OR OMISSIONS FROM THIS LEGEND SHEET DOES NOT IMPLY INCLUSION AND/OR ECLUSION OF ANY PARTICULAR ITEM FROM THE PROJECT. CLEAN AGENT FIRE ETINGUISING SYSTEM DRY AND PRE-ACTION SYSTEM INSPECTOR'S TEST DRAIN DETAIL SPRINKLER MAIN 5 TYPIL UPRIGHT SPRINKLER RISER DETAIL HANGER ROD AC AFF AIR COMPRESSOR ABOVE FINISHED FLOOR BFP BHP BACKFLOW PREVENTER BRAKE HORSEPOWER DCDA DPV DOUBLE CHECK DETECTOR ASSEMBLY DRY PIPE VALVE EC ELECTRIL CONTRACTOR FACP FFA FFB FPC FIRE ALARM FROM FLOOR ABOVE FROM FLOOR BELOW CONTRACTOR GC GPM GENERAL CONTRACTOR GALLONS PER MINUTE HP HORSEPOWER JP JOCKEY PUMP MC CONTRACTOR NC NO NTS NORMALLY CLOSED NORMALLY OPEN NOT TO PC PLUMBING CONTRACTOR TFA TFB TO FLOOR ABOVE TO FLOOR BELOW SPECIFITION, PLAN OR REPORT IS A VIOLATION OF SECTION 79, PROVISION OF THE NEW YORK STATE EDUTION LAW. PLAN DESIGNATION MANUFACTURER MODEL GENERAL AIR PRODUCTS MODEL OL5AC LOTION TYPE FREE AIR (SCFM) BASEMENT OILLESS RISER MOUNTED.5 SYSTEM VOLUME (GAL) 8 8/9/8 AIR COMPRESSOR SCHEDULE (AC) DISCHARGE (PSI) CLEVIS HANGER PIPE ELECTRIL HP VOLTS/ PHASE NOTES 5 / SEE BELOW SYMBOLS, NOTES, ABBREVIATIONS, DETAILS AND SCHEDULES TYPIL PIPE SUPPORT DETAIL NOTES:. PROVIDE WITH MOTOR STARTER SIZE, HP, 5 VOLT, SINGLE PHASE SYSTEM SHALL ACHIEVE PSI IN MINUTES. DOUBLE INTERLOCK PREACTION VALVE SCHEDULE (DPV) PLAN DESIGNATION DPV- MANUFACTURER MODEL VIKING MODEL G-P ASSOCIATED SYSTEM DOUBLE INTERLOCK PRE-ACTION SYSTEM LOTION BASEMENT NOTES:. PROVIDE WITH MODEL E- ACCELERATOR AND MODEL LD- ANTI-COLUMN DEVICE. DESCRIPTION PREACTION VALVE NOMINAL SIZE " " AIR (PSI) NOTES SEE BELOW 8-9-8 CBC CRL PROJ. No. 7 FP

A5 #. A A59 " DEMOLITION NOTES REMOVE SPRINKLER PIPING AND ASSOCIATED SPRINKLER HEADS BACK TO POINT OF DISCONNECTION AS SHOWN AND P. " " " " A " " PASSAGE A58 A55 " " A57 " " A5 " A COURT STREET LITTLE VALLEY, NY 755 # FIRST FLOOR WET SYSTEM DEMOLITION PLAN. : /8" = '-" CONSTRUCTION NOTES TIE INTO WATER SERVICE PIPING AT POINT OF CONNECTION SHOWN. ELBOW ON REMOVE SECTION OF GYPSUM CEILING IN AS NECESSARY, TO FACILITATE BOTTOM SIDE OF WATER SERVICE SHALL BE REPLACE WITH A TEE FITTING TO ALLOW TIE-IN. WORK ABOVE THE CEILING. PATCH CEILING TO MATCH ADJACENT CEILING WHEN WORK ABOVE IS COMPLETE AND PAINT. PROVIDE DRY PIPE VALVE AND TRIM IN RISER. REFER TO DOUBLE INTERLOCK PREACTION SYSTEM RISER DETAIL AND DRY PIPE VALVE SCHEDULE ON FP FOR ADDITIONAL INFORMATION. PROVIDE STUD FRAMING AND GYPSUM WALL BOARD TO ETEND WALL UP TO DECK APPROIMATELY 7'" LONG AND '" HIGH. CMU WALL ENDS JUST ABOVE CEILING AND IS OPEN BETWEEN PROVIDE RISER MOUNTED AIR COMPRESSOR ABOVE DRY PIPE VALVE. REFER TO DOUBLE INTERLOCK PASSAGE AND. WALL SHALL BE ETENDING UP TO CONCRETE DECK TO PROVIDE AN PREACTION SYSTEM RISER DETAIL AND AIR COMPRESSOR SCHEDULE ON FP FOR ADDITIONAL AIRTIGHT SEAL FOR. GWB TO OVERLAP CMU AND BE INSTALLED ON PASSAGE SIDE. INFORMATION. PROVIDE CONTINUOUS SEALANT AROUND EDGE OF GWB. PROVIDE FOR DOUBLE INTERLOCK PREACTION SYSTEM AND LOTE ON FACE OF PROVIDENORTONDOOR CLOSERMODEL 85MOR EQUAL FOR " 8" WOOD DOOR. BLOCK WALL AS INDITED. REFER TO DOULBE INTERLOCK PREACTION SYSTEM RISER DETAIL AND PROVIDE CLOSER WITH PARALLEL ARM, BASE PLATE AND BRACKETS AS NECESSARY TO ATTACH TO ELECTRIL DRAWINGS FOR ADDITIONAL INFORMATION. DOOR. DOOR CLOSER SHALL HAVE ALUMINUM FINISH (89). 5. " PIPING TO INSPECTORS TEST AND DRAIN VALVE LOTED IN BASEMENT.. 75 Essjay Road, Suite Williamsville, NY p:7.88.7 f:7.5.85 5. PROVIDE SEALANT FOR ALL JOINTS AND PENETRATIONS ABOVE CEILING TO CREATE AN AIR-TIGHT SPACE. PROVIDE AMERIN POLYWATER FST FOAM DUCT SEALANT OR SIMILAR FOR SEALING WITHIN INSPECTORS TEST AND DRAIN VALVE LOTED IN RISER. ROUTE DRAIN PIPING FROM DISCHARGE OF CONDUIT AND ELECTRIL SLEEVES. PROVIDE SILICONEULK SEALANT FOR SMALL GAPS UP TO VALVE TO NEAREST FLOOR DRAIN. PROVIDE FUNNEL ATTACHMENT FOR NEAREST FLOOR DRAIN TO AND INCLUDING " WIDE. PROVIDE CLOSED CELL FOAM SEALANT FOR GAPS LARGER THAN " UP TO TCH WATER DISCHARGING FROM PIPE. ". PROVIDE GYPSUM BOARD AND PATCH OPENINGS LARGER THAN ". 7. PROVIDE LB, PSI, CLEAN AGENT TANK FOR SERVICE OF THE.. PROVIDE PERIMETER GASKETING AND RUBBER BOTTOM DOOR SWEEP FOR " 8" WOOD PROVIDE TANK WITH WALL MOUNTING BRACKET AND FILL WITH 79LBS OF NOVEC. REFER TO DOOR. PRODUCTS USED SHALL ENSURE THAT IS SEALED AIR TIGHT. DETAIL ON DRAWING FP FOR CLEAN AGENT SYSTEM COMPONENTS. 7. PROVIDE AIR-TIGHT SEAL AROUND 8 x DUCT. INFILL, PATCH AND SEAL AS REQUIRED TO 8. PROVIDE LB, PSI, CLEAN AGENT TANK FOR SERVICE OF THE. PROVIDE TANK WITH SEAL SPACE. WALL MOUNTING BRACKET AND FILL WITH 7LBS OF NOVEC. REFER TO DETAIL ON DRAWING FP FOR CLEAN AGENT SYSTEM COMPONENTS. 8. SEAL 8" DETER OPENING WITH GWB. OVERLAP GWB A MINIMUM OF ". PROVIDE CONTINUOUS SEALANT AROUND EDGE OF GWB. 9. PROVIDE AGENT RELEASE FOR SEMI-RECESSED INTO THE WALL. ONLY INCHES OF THE PANEL ARE PERMITTED TO PROJECT INTO THE. 9. REMOVE AND REPLACE METAL CEILIGN PANELS TO GAIN ACCESS ABOVE. DISCONNECT AND RECONNECT ELECTRIL GROUND WIRE AS REQUIRED.. PROVIDE AGENT RELEASE FOR, SEMI-RECESSED INTO THE WALL. ONLY INCHES OF THE PANEL ARE PERMITTED TO PROJECT INTO THE.. REMOVE AND REPLACE ACT AND GRID AS NECESSARY TO GAIN ACCESS ABOVE.. PRESSURIZATION TEST SHALL BE CONDUCTED IN ACCORDANCE WITH NFP IF TEST RESULTS IN LEAKAGE, THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROPERLY SEALING THE PROTECTED SPACES. AN ADDITIONAL PRESSURIZATION TEST SHALL BE CONDUCTED AT NO ADDITIONAL CHARGE UNTIL THE SPACE IS PROVEN TO BE SEALED CORRECTLY. CONFERENCE A5 DV- " DUCT " A " " " " " " " TO " REDUCING ELBOW " INCOMING SERVICE " PIPE FFA TO INSPECTORS TEST AND DRAIN CONNECTION 7 5 A59 PASSAGE A58 A " AIR FILLED PIPE TFA 7 SPECIFITION, PLAN OR REPORT IS A VIOLATION OF SECTION 79, PROVISION OF THE NEW YORK STATE EDUTION LAW. A55 A BASEMENT FLOOR PLAN 5 9 8 A57 A5 : /8" = '-" CONFERENCE A5 CONFERENCE A5 8/9/8 A " A59 " " A " A57 A " " FFB " " " " FIRST FLOOR CEILING PLAN 5 : /8" = '-" A59 PARTIAL BASEMENT AND FIRST FLOOR PLANS " 5 A55 PASSAGE " A58 " " " A " A PASSAGE LB CLEAN 7 AGENT TANK A58 " " A5 " 8 LB CLEAN 9 A55 AGENT TANK A A57 A5 " " EIT " TFB AREA OF WORK 8-9-8 CBC CRL PROJ. No. 7 FIRST FLOOR DOUBLE INTERLOCK PREACTION PLAN : /8" = '-" FIRST FLOOR CLEAN AGENT PLAN : /8" = '-" KEYPLAN FP

SYMBOLS & ABBREVIATIONS SCHEDULE RECEPTACLES LP, DUPLE RECEPTACLE OUTLET, 8" F.F., AMP COMMERCIAL GRADE GROUNDING TYPE WITH MATCHING COVERPLATE. TAG INDITES PANELBOARD & BRANCH CIRCUIT THAT IT IS CONNECTED TO. LP, GFCI RECEPTACLE OUTLET, 8" F.F., AMP COMMERCIAL GRADE GROUNDING TYPE WITH MATCHING COVERPLATE. TAG INDITES PANELBOARD & BRANCH CIRCUIT THAT IT IS CONNECTED TO. ABBREVIATIONS: WP WG AFF AFG OC UC VNAC ANAC SLC ATS HP kw kva VFD EM NL LTG CPWR PWR EH KIT LMTR EQP NEC MLO MCB AWG POWER WALL MOUNTED JUNCTION BO, SIZE AS INDITED OR PROVIDE MINIMUM SIZE REQUIRED BY LATEST EDITION OF NATIONAL ELECTRIL CODE (NFPA 7-NEC). J PROVIDE COMPLETE ELECTRIL CONNECTION TO INDITED (INCLUDING DISCONNECT, CONDUCTORS, RACEWAY, & OTHER REQUIRED HARDWARE. - INDITES TAG. REFER TO SCHEDULE FOR ADDITIONAL INFORMATION. ELECTRIL PANELBOARD, SURFACE MOUNTED. UNLESS OTHERWISE NOTED, INSTALL AT 7" F.F. TO THE TOP OF THE BO. TYPIL WALL ELECTRIL PANELBOARD, FLUSH MOUNTED. UNLESS OTHERWISE NOTED, INSTALL AT 7" F.F. TO THE TOP OF THE BO. TYPIL WALL TYPIL DISCONNECT (SAFETY SWITCH). REFER TO DRAWINGS FOR SIZE & ADDITIONAL FUSING REQUIREMENTS. INDITES WEATHERPROOF DEVICE OR INDITES DEVICE SHALL HAVE WIRE GUARD PROTECTION ABOVE FINISHED FLOOR ABOVE FINISHED GRADE SHALL REMAIN IN PLACE OVER COUNTER (INSTALL " ABOVE COUNTER HEIGHT) UNDER COUNTER (INSTALL 8" ABOVE FINISHED FLOOR) VISUAL NOTIFITION APPLIANCE CIRCUIT AUDIO NOTIFITION APPLIANCE CIRCUIT SIGNALING LINE CIRCUIT AUTOMATIC TRANSFER SWITCH HORSEPOWER KILOWATT KILOVOLT-AMPERES VARIABLE FREQUENCY DRIVE EMERGENCY NIGHTLIGHT (TYPIL FOR LIGHTING, 'ON' ALL THE TIME) LIGHTING CONTINUOUS LOAD (POWER) POWER ELECTRIC HEAT KITCHEN LARGEST MOTOR SHOP NATIONAL ELECTRIL CODE MAIN LUGS ONLY MAIN CIRCUIT BREAKER AMERIN WIRE GAGE GENERAL NOTES: (FOR ALL DRAWINGS) THE DRAWINGS ARE DIAGRAMMATIC & INDITE GENERALLY THE LOTIONS OF THE MATERIAL &. THESE DRAWINGS SHALL BE FOLLOWED AS CLOSELY AS POSSIBLE. B. MINOR DETAILS NOT USUALLY SHOWN OR SPECIFIED, BUT NECESSARY FOR PROPER INSTALLATION & OPERATION, SHALL BE INCLUDED IN THE CONTRACTOR'S BID, THE SAME AS IF HEREIN SPECIFIED OR SHOWN. C. ALL MATERIAL & INSTALLATION SHALL BE IN ACCORDANCE WITH LATEST EDITION OF THE NATIONAL ELECTRIC CODE, LATEST EDITION OF LOL CODES, & ORDINANCES. D. ALL CONDUITS ON EPOSED WORK SHALL BE RUN AT RIGHT ANGLES TO, & PARALLEL WITH, THE SURROUNDING WALL & SHALL CONFORM TO THE FORM OF THE CEILING. DIAGONAL RUNS WILL NOT BE ALLOWED. BENDS IN PARALLEL CONDUIT RUNS SHALL BE CONCENTRIC. ALL CONDUIT SHALL RUN PERFECTLY STRAIGHT & TRUE. E. F. ELECTRIL PIECE OF. REFER TO DRAWINGS FOR ADDITIONAL INFORMATION. BRANCH CIRCUIT WIRING NOTES: FIRE ALARM FIRE ALARM SYSTEM SMOKE SENSOR. (CEILING MOUNTED) PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. (ROUND-CEILING MOUNTED, SQUARE-WALL MOUNTED). TAG '' INDITES SMOKE DETECTORS SHALL BE ASSOCIATED WITH THE CLEAN AGENT SYSTEM. FIRE ALARM SYSTEM HEAT DETECTOR. UNLESS OTHERWISE NOTED, PROVIDE COMBINATION FIED (5 F) & RATE-OF-RISE (5 PER MINUTE) TYPE DEVICE. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. CO CEILING MOUNTED UNLESS OTHERWISE NOTED, MINIMUM HOMERUN (HOMERUN SHALL BE CONSIDERED TOTAL LENGTH FROM SOURCE TO LAST DEVICE ON THE CIRCUIT) CONDUCTORS FOR A/P BRANCH CIRCUITS INCLUDING LIGHTING SHALL BE AS FOLLOWS: -FT - # AWG -5FT - # AWG 5-5FT - #8 AWG 5-FT - # AWG. & LONGER - # AWG. REDUCE CONDUCTORS SIZE TO A MAIMUM CONDUCTOR SIZE THAT THE LOAD TERMINALS N ACCOMMO, REDUCED SIZE NOT LONGER THAN ONE FOOT. INCREASE RACEWAY SIZE AS NEEDED PER NEC, FOR THE LARGER SIZES OF CONDUCTORS. TS RBON MONOIDE DETECTOR. PROVIDE & INSTALL ALL REQUIRED WIRING BY SELECTED MANUFACTURER. CO WALL MOUNTED FIRE ALARM SYSTEM REMOTE TEST STATION. PROVIDE WHERE INDITED ON DRAWING & INTERFACE WITH DETECTION DEVICE INDITED. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. FIRE ALARM SYSTEM MANUAL PULL STATION. PROVIDE COMPLETE INSTALLATION WITH PROTECTIVE COVER WHERE REQUIRED. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. F REMOVAL (TYPIL FOR ALL DEVICES): cd FIRE ALARM SYSTEM WATER. PROVIDE COMPLETE INTERFACE BETWEEN & FIRE ALARM. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. ALL CONDUIT RUNS ARE TO BE CONCEALED IN WALLS, CEILINGS, OR IN THE SLAB. CONTRACTOR SHALL COORDINATE CONDUIT INSTALLATION DURING BUILDING CONSTRUCTION WITH OTHER TRADES. RUN SURFACE RACEWAY ONLY WHERE LLED FOR OR SHOWN ON THE DRAWINGS. EPOSED CONDUIT SHALL ONLY BE INSTALLED WHERE MEANS OF CONCEALING DOES NOT EIST. CONTRACTOR IS TO NOTIFY ENGINEER & GET OWNERS APPROVAL PRIOR TO RUNNING EPOSED CONDUITS. COURT STREET LITTLE VALLEY, NY 755 INTERIOR POWER BRANCH CIRCUITS SHALL BE IN EMT CONDUIT. A MAIMUM OF () CIRCUITS N BE GROUPED TOGETHER IN A HOMERUN CONDUIT. EACH CIRCUIT SHALL HAVE SEPARATE NEUTRAL, GROUPING OF NEUTRALS SHALL NOT BE ACCEPTABLE. EACH CIRCUIT SHALL ALSO HAVE A GROUND WIRE SIZED PER NEC. USING CONDUIT, OR MC BLE AS GROUND PATH SHALL NOT BE ACCEPTABLE. BLE MUST BE SUPPORTED PER NEC, GROUPING OF GROUND WIRES [() GROUND PER () CIRCUITS] IS ACCEPTABLE. G. THE CONTRACTOR IS RESPONSIBLE FOR ALL REQUIRED COSTS FOR SEALING ALL PENETRATIONS THROUGH FIRE & SMOKE WALLS USING UL APPROVED SEALANT & METHODS. H. 75 Essjay Road, Suite Williamsville, NY p:7.88.7 f:7.5.85 UNLESS OTHERWISE NOTED, PROVIDE ALL NEW RACEWAYS. USE SURFACE RACEWAY ONLY WHERE INDITED ON THE PLANS. IF CONTRACTOR INTENDS TO UTILIZE SURFACE RACEWAY IN AREAS OTHER THOSE INDITED ON PLANS, PRIOR APPROVAL IS REQUIRED FROM ENGINEER & OWNER. I. CONTRACTOR MAY REUSE CONCEALED CONDUIT UNLESS OTHERWISE NOTED ON THE PLANS. J. ALL RACEWAYS CROSSING BUILDING EPANSION JOINTS SHALL BE EQUIPPED WITH EPANSION FITTINGS. K. CONTRACTOR SHALL PROVIDE INFORMATION LABELS ON ALL RECEPTACLES, PANELBOARDS, JUNCTION BOES, WALL SWITCHES, & DISCONNECT SWITCHES. LABELS SHALL BE PHENALIC TYPE WITH BLACK BACKGROUND & WHITE ENGRAVED LETTERING. LABEL SHALL INDITED CIRCUIT/FEEDER SOURCE & ID NAME. TYPIL POWER & SYSTEMS DEVICE SCHEDULED FOR REMOVAL. DISCONNECT & REMOVE ALL ASSOCIATED ELECTRIL WORK AS INDITED ON CONTRACT DOCUMENTS. REINSTALL AS REQUIRED FIRE ALARM SYSTEM TAMPER SWITCH. PROVIDE COMPLETE INTERFACE BETWEEN TAMPER SWITCH & FIRE ALARM. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. FA FIRE ALARM SYSTEM WATER FLOW ALARM INTERFACE. PROVIDE COMPLETE ELECTRIL INTERFACE TO ALARM (PROVIDED & INSTALLED BY SPRINKLER CONTRACTOR, WIRED BY ELECTRIL CONTRACTOR). PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. FIRE ALARM SYSTEM INDIVIDUAL ADDRESSABLE MODULE. PROVIDE WHERE REQUIRED PER SPECS/DETAILS. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. FSR FIRE ALARM SYSTEM FAN SHUT-DOWN RELAY. PROVIDE WHERE REQUIRED PER SPECS/DETAILS. CONTACT RATING SHALL MATCH FAN MOTOR FEEDER RATING. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. ISO FIRE ALARM SYSTEM ISOLATION MODULE. PROVIDE WHERE REQUIRED PER SPECS/DETAILS. INSTALL EVERY 5TH INITIATING DEVICE ON SLC LOOP. PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. FACP A TYPIL FIRE ALARM. SURFACE OR FLUSH MOUNTED. PROVIDE WHERE INDITED ON FLOOR PLANS. INSTALL APPROIMATELY 7" F.F. TO TOP OF BO. PROVIDE DEDITED VAC, A/P CIRCUIT & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. TYPIL LUMINAIRE SCHEDULED FOR REMOVAL. REFER TO LUMINAIRE SCHEDULE FOR ADDITIONAL INFORMATION. REMOVAL NOTES: NOT ALL DEVICES SCHEDULED FOR REMOVAL ARE SHOWN ON THIS SCHEDULE. ALL DEVICES TO BE REMOVED ARE MARKED WITH THE SAME LINETYPE & LINE WEIGHT AS SYMBOLS ABOVE. REFER TO DEMOLITION PLANS FOR ADDITIONAL INFORMATION. TO REMAIN (TYPIL FOR ALL DEVICES): ABORT BUTTON. (WALL MOUNTED) PROVIDE & INSTALL ALL WIRING AS REQUIRED BY SELECTED MANUFACTURER. TAG '' INDITES SMOKE DETECTORS SHALL BE ASSOCIATED WITH THE CLEAN AGENT SYSTEM. cd TYPIL POWER & SYSTEMS DEVICE TO REMAIN IN PLACE. LUMINAIRE SCHEDULED TO REMAIN IN PLACE. REFER TO LUMINAIRE SCHEDULE FOR ADDITIONAL INFORMATION. TO REMAIN NOTES: NOT ALL DEVICES SCHEDULED TO REMAIN ARE SHOWN ON THIS SCHEDULE. ALL DEVICES SCHEDULED TO REMAIN ARE MARKED WITH THE SAME LINETYPE & LINE WEIGHT AS SYMBOLS ABOVE. REFER TO FLOOR PLAN DRAWINGS FOR ADDITIONAL INFORMATION. SPECIFITION, PLAN OR REPORT IS A VIOLATION OF SECTION 79, PROVISION OF THE NEW YORK STATE EDUTION LAW. GENERAL SYMBOLS THIS SYMBOLS & ABBREVIATIONS SCHEDULE IS FOR THE ELECTRIL CONTRACTOR REFERENCE ONLY. NOT ALL SYMBOLS OR ABBREVIATIONS MAY APPLY TO THIS PARTICULAR PROJECT. ANY ADDITIONS OR OMMISSIONS FROM THIS SCHEDULE DOES NOT IMPLY INCLUSION AND / OR ECLUSION OF ANY PARTICULAR ITEM FROM THE PROJECT. 8/9/8 ELECTRIL SYMBOLS, NOTES & ABBREVIATIONS " " 8-9-8 MJC PROJ. No. 7 E JJR

TO FACP ON FIRST FLOOR CONSTRUCTION NOTES:. PROVIDE () AMP CIRCUIT BREAKERS IN PANELBOARD PNL-(SQUARE DNQ SERIES) FOR POWER TO THE DOUBLE INTERLOCK PREACTION AND AIR COMPRESSOR. PROVIDE /" EMT CONDUIT WITH - # AWG & - # AWG GROUND FOR POWER WIRING TO THE DOUBLE INTERLOCK PREACTION AND AIR COMPRESSOR. DOUBLE INTERLOCK PREACTION. INSTALL ON UNISTRUT FRAME MOUNTED TO THE FLOOR. REFER TO DETAIL ON THIS DRAWING FOR ADDITIONAL INFORMATION. PROVIDE " EMT CONDUIT FOR CONTROL WIRING ( SWITCH, SMOKE HEAD, AND SUPERVISORY SWITCH) BACK TO THE FIRE ALARM. REFER TO MANUFACTURER'S DEVICE WIRING REQUIREMENTS FOR SPECIFIC WIRING DETAILS. 5. PROVIDE /" EMT CONDUIT WITH - #8/ BLES FOR SMOKE HEADS LOTED ON THE FIRST FLOOR (S A-55, A-5 & A-59 - TYPIL - ).. PROVIDE (INDIVIDUAL ADRESSABLE MODULE) FOR THE LOW SWITCH AND SMOKE DETECTORS (LOTED ON FIRST FIRST FLOOR). PROVIDE ALL REQUIRED WIRING BETWEEN SIGNALING DEVICES AND ASSOCIATED. COURT STREET LITTLE VALLEY, NY 755 MODIFY CONDUIT RUN AS NEEDED TO AVOID HVAC DUCTWORK 75 Essjay Road, Suite Williamsville, NY p:7.88.7 f:7.5.85 PANELBOARDLP-GA NEW DOUBLE INTERLOCK PREACTION SUPERVISORY SWITCH J REFER TO DETAIL ON THIS DRAWING FOR WIRING IN THIS AREA TO ON FIRST FLOOR 5 PANELBOARDPNL- " WATER SERVICE PARTIAL BASEMENT LEVEL ELECTRIL NEW WORK PLAN : /8" = ' " TO SMOKE HEAD IN A-55 AND MODULES FROM CLEAN AGENT S TO PANELBOARD PNL- TYPIL -/" GALVANIZED METAL UNISTRUT SPECIFITION, PLAN OR REPORT IS A VIOLATION OF SECTION 79, PROVISION OF THE NEW YORK STATE EDUTION LAW. TO WATER MANIFOLD ( SWITCH AND SOLENOID) /" EMT CONDUITS (TYPIL ) FROM DETECTOR LOTED IN SPACE PROTECTED BY PREACTION SYSTEM MAINTENANCE AIR COMPRESSOR CONTROL WIRE INSTALLED IN CONDUIT (TYP.) TO FACP LOW (TROUBLE) SMOKE (ALARM) DOUBLE INTERLOCK PREACTION RELEASING LOW AIR PANEL ALARM SWITCH 8/9/8 SOLENOID VALVE NORMALLY CLOSED 8/ BLE (SLC) IN CONDUIT (TYP.) FOUR HOLE UNISTRUT FLOOR MOUNTING BRACKET (TYPIL ) FLOOR LINE DOUBLE INTERLOCK PREACTION MOUNTING DETAIL ELECTRIC MANUAL CONTROL STATION, LOTED IN PASSAGE A-58 DELUGE VALVE WITH DOUBLE INTERLOCK TRIM (TRIM NOT SHOWN) PARTIAL BASEMENT & FIRST FLOOR ELECTRIL PLANS SUPERVISORY SWITCH DOUBLE INTERLOCK PREACTION SYSTEM WIRING DETAIL : NO " EIT : NO AREA OF WORK 8-9-8 MJC PROJ. No. 7 KEYPLAN " E JJR

GENERAL NOTES: CONTROL A-7 SERGEANT & RECORDS A-9 WAITING A- SEARCH A-8 SECURE VISITING A-5 REFER TO SPECIFITION FOR ADDITIONAL INFORMATION REGARDING THE SEQUENCE OF OPERATION FOR THE CLEAN AGENT SYSTEM. B. PROVIDE A SIGN AT EACH MANUAL PULL STATION WITH THE LABEL "" (TOTAL OF ) STATING "ACTIVATION OF THIS FIRE ALARM PULL STATION WILL INITIATE AN ALARM IN THE CLEAN AGENT SYSTEM" SIMPLE ES FIRE ALARM FACP A-5 CONSTRUCTION NOTES:. PROVIDE () AMP CIRCUIT BREAKER IN PANELBOARD PNL-FOR POWER TO THE CLEAN AGENT S. CONCEAL ALL CONDUIT ABOVE THE DROP CEILING OR IN THE WALLS OF THE DRYWALL. PROVIDE /" EMT CONDUIT WITH () - # AWG & ()- # AWG GROUND FOR POWER WIRING TO THE CLEAN AGENT. PROVIDE SMOKE DETECTOR COMPATIBLE WITH THE NEW DOUBLE INTERLOCK PREACTION FIRE ALARM. WIRE DEVICE BACK TO DOUBLE INTERLOCK PREACTION IN THE BASEMENT FIRE ALARM MANUAL PULL STATION. PROVIDE RACEWAY AND WIRE TO DOUBLE INTERLOCK PREACTION IN THE BASEMENT. COURT STREET LITTLE VALLEY, NY 755 VISITING A-5 75 Essjay Road, Suite Williamsville, NY p:7.88.7 f:7.5.85 A- A-59 CLEAN AGENT TANK A- A PASSAGE A-58 A- F A-55 PANELBOARDLP-B NEW CLEAN AGENT F J F LIEUTENANT A-57 A CLEAN AGENT TANK A-5 PANELBOARDPNL- NEW CLEAN AGENT PARTIAL FIRST FLOOR NEW WORK PLAN : /8" = ' " HS ZONE # TO NEW DOUBLE INTERLOCK PREACTION TO FIRE ALARM SYSTEM SPECIFITION, PLAN OR REPORT IS A VIOLATION OF SECTION 79, PROVISION OF THE NEW YORK STATE EDUTION LAW. HS () # AWG (TYPIL) F () # AWG A TO MONITOR CLEAN AGENT CONTROLLER FOR ALARM CLEAN AGENT CONTROL PANEL () # AWG & # GND IN /" CONDUIT TO CKT. No. 9 PNL- IN B. 8/9/8 RISER NOTES: UNLESS OTHERWISE NOTED- THE CLEAN AGENT SYSTEM DEVICES SHALL BE FURNISHED BY THE SYSTEM VENDOR/PROVIDER. REFER TO DRAWINGS & SPECIFITIONS FOR INFORMATION REGARDING CLEAN AGENT SYSTEM DEVICES. PARTIAL BASEMENT & FIRST FLOOR ELECTRIL PLANS FIRE ALARM SEQUENCE OF OPERATION: DESIGNATED SMOKE DETECTORS SHALL INITIATE ALARM SEQUENCE IN THE DRY CHEMIL CONTROLLER. FIRE ALARM SHALL MONITOR STATUS VIA ADDRESSABLE MODULE- UPON INITIATION OF ALARM- THE FACP SHALL ENTER ALARM MODE INITIATING EVACUATION SEQUENCE. : NO " CLEAN AGENT RISER DIAGRAM EIT AREA OF WORK 8-9-8 MJC PROJ. No. 7 KEYPLAN " E JJR