1 Technical Specifi cations CONFORMS TO ANSI/UL STD. 1995, ANSI STD. Z21.47 CERTIFIED TO CAN/CSA STD. C22.2 NO. 236, CAN/CSA STD. 2.3 AND CAN/CGA STD. 2.17 PSS - SERIES REV-B Mid Efficiency Gas Heat / Electric Cooling Self contained, Standard efficiency Thru-The-Wall heating & cooling unit Up to 80% AFUE/Thermal Efficiency, AHRI Certified Input 26 000-64 000 BTU/h FEATURES COMPATIBLE BOX SIZE Industry standard footprint for retrofit applications Appliance shell dimensions: 43 1/8 High x 28 Wide x 32 Deep Wall Sleeve dimensions where penetrating exterior wall: 44 7/8 High x 28 7/8 Wide Standard TAUPE color HEATING FEATURES Up to 80 % AFUE/Thermal Efficiency Single Stage Gas Module Stainless steel heat exchanger Sealed Vestibule keeps cold external air from circulating in dwelling HEATING MODULE CIRCULATION BLOWER Dual Inlet Blower for higher flow rates / reduced air noise Endura Pro Multi-Speed Electronically Commutated Motor for increased electrical efficiency FEATURES Up to 11 EER R-410A Refrigerant System Micro-Channel Condenser and Evaporator Coils High Efficiency Compressors One Piece motorized Condenser Fan design SERVICE ADVANTAGES MODULE Indoor access to all parts & maintenance needs Innovative, dual slide-out chassis can be partially or fully removed for efficient servicing With spare modules, building management can perform quick swap outs, maintaining indoor conditions in the apartment/condo, while troubleshooting non functioning units off line Can perform direct replacement of the individual modules at the end of their service life instead of replacement of the complete appliance All control harnesses are separated with modular quick disconnects so module swap outs do not require time consuming rewiring
2 NOMENCLATURE P S C 040 A 018 A BRAND MODEL HEAT TYPE HEAT CAPACITY TYPE CAPACITY REVISION P=Condo Pack S=Single Packaged Vertical R=Roof Top P=Packaged Residential C - Gas Condensing S - Gas Standard E - Electrical H - Hydronic D - Duct only (No heat) i.e. PSD000A012A Gas Condensing(96%) Gas Standard(80%) Heat designation Heat designation 000 - Duct Only 000 - Duct Only 015-15 000 Btu/h 026-26 000 Btu/h 030-30 000 Btu/h 038-38 000 Btu/h 040-40 000 Btu/h 051-51 000 Btu/h 050-50 000 Btu/h 064-64 000 Btu/h Electric Heat Hydronic Heat Heat designation Heat designation 000 - Duct Only 000 - Duct Only 005-5.0 kw 030-30 000 Btu/h 007-7.5 kw 042-42 000 Btu/h 010-10 kw 015-15 kw A, B, C... Air Conditioning 000 - Blower Only 012-12 000 Btu/h / 1.0 Ton 018-18 000 Btu/h / 1.5 Ton 024-24 000 Btu/h / 2.0 Ton 030-30 000 Btu/h / 2.5 Ton A - Air Conditioning - std. eff. Rev A B - Air Conditioning - std. eff. Rev B C - Air Conditioning - high eff. H - Heat Pump - std. eff. P - Heat Pump - high eff. F - Blower Only (No Cool) i.e. PSC040F000A Example: PSC040B018A - Condo Pack - Single Packaged Vertical - Condensing Gas heating 40k Btu/h - Rev B AC 1.5 ton - Rev A *All specifications and designs can change without notice to allow for on-going improvements. Images may not be exactly as shown. Consult with your owner s manual for current information. Check all local and national building codes and gas regulations. Napoleon is a registered trade mark of Wolf Steel Ltd.
3 PERFORMANCE SPECIFICATIONS HEATING PSS026B012A PSS026B018A PSS026B024A PSS026B030A PSS038B012A PSS038B018A PSS038B024A PSS038B030A Thermal Efficiency 80% 80% 80% 80% 80% 80% 80% 80% AFUE 80% 80% 80% 80% 80% 80% 80% 80% Input BTU/h 26,000 26,000 26,000 26,000 38,000 38,000 38,000 38,000 Output BTU/h (Thermal Efficiency) 20,800 20,800 20,800 20,800 30,400 30,400 30,400 30,400 Output BTU/h (AFUE) 20,800 20,800 20,800 20,800 30,400 30,400 30,400 30,400 BTU/h 12,000 16,000 21,000 25,000 12,000 16,000 21,000 25,000 EER 11 10.0 10.0 9.0 11 10.0 10.0 9.0 REF. R410A R410A R410A R410A R410A R410A R410A R410A WEIGHT (lb) 328 349 349 349 328 349 349 349 HEATING PSS051B012A PSS051B018A PSS051B024A PSS051B030A PSS064B012A PSS064B018A PSS064B024A PSS064B030A Thermal Efficiency 80% 80% 80% 80% 80% 80% 80% 80% AFUE 80% 80% 80% 80% 80% 80% 80% 80% Input BTU/h 51,000 51,000 51,000 51,000 64,000 64,000 64,000 64,000 Output BTU/h (Thermal Efficiency) 40,800 40,800 40,800 40,800 51,200 51,200 51,200 51,200 Output BTU/h (AFUE) 40,800 40,800 40,800 40,800 51,200 51,200 51,200 51,200 BTU/h 12,000 16,000 21,000 25,000 12,000 16,000 21,000 25,000 EER 11 10.0 10.0 9.0 11 10.0 10.0 9.0 REF. R410A R410A R410A R410A R410A R410A R410A R410A WEIGHT (lb) 328 349 349 349 328 349 349 349 AIR FLOW H BTU/h ATING CFM at external static pressure, inches Water Column Module No. BTU/h SETTING SPEED 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 CSGM026A 26 kbtu/h Factory 5 433 429 405 330 283 260 227 202 - - High 4 565 535 524 488 421 380 337 300 283 259 CSGM038A 38 kbtu/h Factory 4 565 535 524 488 421 380 337 300 283 259 High 3 768 745 731 711 688 661 626 591 553 522 CSGM051A 51 kbtu/h Factory 3 768 745 731 711 688 661 626 591 553 522 High 2 931 902 886 867 859 839 818 781 721 637 CSGM064A 64 kbtu/h Factory 2 931 902 886 867 859 839 818 781 721 637 High 1 998 976 957 931 907 889 845 805 747 648 Module No. Size SETTING SPEED 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 CACM012B 1.0 TON Factory 5 433 429 405 330 283 260 227 202 - - High 4 565 535 524 488 421 380 337 300 283 259 CACM018B 1.5 TON Factory 3 768 745 731 711 688 661 626 591 553 522 High 2 931 902 886 867 859 839 818 781 721 637 CACM024B 2.0 TON Factory 3 768 745 731 711 688 661 626 591 553 522 High 2 931 902 886 867 859 839 818 781 721 637 CACM030B 2.5 TON Factory 1 998 976 957 931 907 889 845 805 747 648 ELECTRICAL Description 1.0 TON 1.5 TON 2.0 TON 2.5 TON Compressor Type Rotary Rotary Rotary Scroll Rated Amps 5.3 7.4 10.0 12.8 LRA 28.5 38.5 34.8 67.8 MCA 10.2 12.8 16.7 20.2 Max Fuse/Breaker (A) 15 20 25 30 Indoor Fan FLA / HP / RPM 2.8 / 1/3 / 1050 2.8 / 1/3 / 1050 2.8 / 1/3 / 1050 2.8 / 1/3 / 1050 Condenser Fan FLA / HP / RPM.79/ 1/4/ 1100.79/ 1/4/ 1100 1.4 / 1/3 / 1600 1.4 / 1/3 / 1600 Combustion Fan FLA 1.25 1.25 1.25 1.25 Unit Input Voltage - Frequency- Phase 208/230V-60Hz-1PH GAS CONTROLS AND ADDITIONAL DATA IGNITION SYSTEM SPARK IGNITION GAS CONNECTION 1/2" NPT AC CONDENSATE HOSE SIZE (Supplied) 5/8 " ID
4 DIMENSIONS WALL SLEEVE DIMENSIONS FOUR DIFFERENT WALL SLEEVE MODELS ARE DEPICTED BELOW: <== CWSMUA17 <== CWSMUA19 17.000 19.000 16.000 DIMENSIONS FOR THE TOP PANEL (ITEM 1): <== CWSMUA <== CWSMUA15 NOTE: TO IMPROVE RIGIDITY AND REDUCTION IN VIBRATION WALL MOUNTING BRACKETS CAN BE USED TO AFFIX WALL SLEEVE TO BUILDING SUB STRUCTURE FROM INSIDE OR OUTSIDE OF THE BUILDING. ENGINEER/ARCHITECT TO CONSULT WITH NAPOLEON ENGINEERING TO DETERMINE BRACKET LOCATION FOR SETTING THE DESIRED DEPTH OF WALL SLEEVE INTO WALL. WALL SLEEVE IS DIRECTLY LAGGED TO WALL SUBSTRUCTURE. 3 34" 7 28 8 " POSITION A 1" POSITION B CENTRAL BRACE MOUNTING LOCATIONS 1 42 4 " 7 46 8 " 7 44 8 " 1 26 2 " 15 16 " 3 32 4 " CWSMUA CWSMUA15 CWSMUA17 CWSMUA19 DIMENSIONS FOR THE SIDE PANELS (ITEM 3 & 4)): 12.590 14.890 16.890 18.890 <== CWSMUA <== CWSMUA15 <== CWSMUA17 <== CWSMUA19
* 32" 5 ENCLOSURE FOR CONDO PACK FIGURE 1 MINIMUM CLEARANCE REQUIRED DUE TO UNIT S DIMENSION & SAFETY STANDARD 2" MIN. CLEARANCE TO COMBUSTIBLE 0" MIN. CLEARANCE 2" MIN. CLEARANCE OUTSIDE Exterior wall Exterior wall ***SECURE TO WALL 29" REF. 1.5" Ø 0.25 " MIN. CLEARANCE **A **B DOOR OPENING 1" REF. CLEARANCE BETWEEN LEFT (HINGE) SIDE DOOR JAM AND CONDO PACK 8" MIN. FLOOR DRAIN REQUIRED (1.5" Ø MIN.) FOR REMOVAL OF AC CONDENSATE *32 " FABRICATED WOOD OR STEEL SUPPORT NOTE ADEQUATE SERVICE CLEARANCE MUST BE PROVIDED IN FRONT OF THE UNIT. ***Engineer/Architect - to consult with Napoleon Engineering to determine bracket location for setting the desired depth of Wall Sleeve into wall. ** A clear and unobstructed passageway (dimension AxB) shall be provided to the unit, in accordance with the requirements of the local authorities having jurisdiction and with the National Fuel Gas Code, ANSI Z223.1 (latest edition) and the National Electrical Code in the United States or CAN/CGA-B149.1 &.2 and the Canadian Electrical Code CSA C22.1 Part 1 (latest edition) in Canada. * The 32" x 32" unobstructed clearance is required in front of the unit for complete removal of heating and cooling module. Check local building codes for other applicable requirements. IMPORTANT: Prior to constructing interior closet walls in close proximity to the wall sleeve, the sealing of the wall sleeve and cabinet should be completed. Sealing after the walls are constructed can be difficult. Poor sealing will result in cold air infiltration that will affect Condo Pack. Refer to section "Sealing: Wall Sleeve and Condo Pack cabinet".
6 ENCLOSURE FOR CONDO PACK cont. FIGURE 2 IMPORTANT: MINIMUM REQUIRED VERTICAL CLEARANCE OF A VENT TERMINAL AND OVERHANGING STRUCTURE FROM THE TOP OF THE GAS VENT IS 12 (MORE THAN 12" IS RECOMMENDED). CHECK LOCAL BUILDING CODES FOR OTHER REQUIREMENTS. NOTE: IT IS ALWAYS A GOOD PRACTICE TO MAXIMIZE THE CLEARANCE AS MUCH AS POSSIBLE BETWEEN VENT TERMINAL AND SURROUNDING STRUCTURES TO AVOID ANY POTENTIAL DAMAGE, DEGRADATION AND ICING, SINCE THE FLUE GASES CONTAIN WATER VAPOR AND ARE TYPICALLY MILDLY ACIDIC. CONSULT WITH EXTERIOR WALL FINISH MANUFACTURER FOR MORE INFORMATION. NOTE *** *** Refer to: ENCLOSURE FOR CONDO PACK Figure 1, page 5. A 2" MIN. CLEARANCE TO COMBUSTIBLE ***SECURE TO WALL **B 82" REF. 43 1/8" FLOOR 8" MIN. FABRICATED WOOD OR STEEL SUPPORT A DRAIN Flashing 16 " Seal around Sleeve and INSIDE wall 12 9/16" Flashing A-A 32 1/8" REF. * 12" MIN. Clearance from the top of the Gas Vent to exterior overhang 44 7/8 " REF. Brick Wall PROTRUDE 1/2 MIN.-1 MAX. Seal around Sleeve and OUTSIDE wall PROTRUDE 1/2 MIN.-1 MAX. Brick Wall ROUGH OPENING TO SUIT 28 7/8" X 44 7/8" WALL SLEEVE 28 7/8" C 4 5/8" REF. 5 3/4" REF. GAS VENT POSITION 44 7/8 " REF. C VIEW OF OUTSIDE WALL
CONDO PACK SHOWN IN WALL SLEEVE 7 8" MIN FLOOR 15 16 " 16" WALL SLEEVE 20 1 2 " 8" AIR SUPPLY OUTLET 5 3 8 " 24 1 4 " 3 1 8 " 28 1 4 " CONDO PACK UNIT HEATING MODULE (FURNACE) 3 1 2 " 28" 29" ELECTRICAL CONNECTION GAS CONNECTION MODULE (AIR CONDITIONER) 43 1 8 " 45 3 8 " 44 7 8 " AC DRAIN HOSE 12 16 9 " 1 1 16 " 1 15 16 " 24 1 8 " 1 15 16 " 25 1 16 " 7 1 8 " AIR RETURN INLET 32 1 8 " 28 7 8 " REF
8 SEALING: WALL SLEEVE AND CONDO PACK CABINET Wall Sleeve Cabinet Cabinet Wall Sleeve SEAL HERE SEAL HERE SEAL ON TOP SEAL LEFT SIDE SEAL RIGHT SIDE SEAL BOTTOM Fill the clearance space between the sleeve and the cabinet with non-hardening caulking compound or non-expanding insulation foam as a protection against the snow, water, moisture and air infiltration.! IMPORTANT! THE CLEARANCE SPACE BETWEEN THE WALL SLEEVE AND THE CABINET MUST BE COMPLETELY SEALED ON ALL FOUR SIDES IN ORDER TO PREVENT THE MOISTURE AND AIR INFILTRATION.! WARNING! THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED SERVICE PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND OPERATION OF THE UNIT. READ THESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING INSTALLATION OR OPERATION. IMPROPER INSTALLATION, ADJUSTMENT, SERVICE, OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. FOR INFORMATION AND ASSISTANCE CONSULT A QUALIFIED INSTALLER OR SERVICE AGENCY. SIDE VIEW SEAL BOTTOM TOP VIEW SEAL CORNERS CABINET CABINET SEAL ON TOP SEAL ON BOTH SIDES Wall Sleeve Wall Sleeve
9
24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 PHONE: 866-820-8686 FAX: 705-725-1150 Website: www.napoleonheatingandcooling.com General: hvac@napoleonproducts.com Technical inquiries: hvacsupport@napoleonproducts.com 9700539