Fans Air Handling Units Air Distribution Products Fire Safety Air Curtains and Heating Products Tunnel Fans Roof Fan DVG EC Smoke extraction and daily ventilation in one! C/12min 12 C
2 Roof Fan DVG EC Roof Fan DVG EC Pstat 12 11 1 9 8 7 6 Quick selection C/12min 12 C Q 8 12 16 2 2 28 DVG-H EC DVG-V EC 8 Normal ventilation + smoke and heat extract unit (dual use) Up to C / 12 min (F/12, F/9, F, F2) Normal ventilation up to 12 C continuous operation, up to 8 C in standstill (when the fan doesn`t operate) Horizontal (DVG-H) exhaust or vertical exhaust (DVG-V) Service switch serial Suitable for coastal applications Wide range of accessories Tested acc. to EN 1211- at LGAI, Barcelona CE-certification acc. to EN 1211- Meet ErP efficiency goal for dual use fans 1~ (2-26V, /6Hz) or ~ (2-6V, /6Hz) EC (electronically commutated) high efficiency motor -1V speed control input Modbus control possible Fire mode integrated Ten models available, five for vertical and five for horizontal exhaust. The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation. Smoke-free escape ways increase the chances to rescue people in case of fire. For installation only on top of heated buildings. The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air. 2 1 6 6 1.11 2.22...6 6.67 7.78 Q Technical data Item No. Model Nominal voltage Input power P1 [kw] Current [A] Max. airflow R. p. m. [min -1] Sound pressure level at /1 m [db(a)] Weight [kg] Wiring diagram 921 DVG-H EC/F 1~2V, 1,8 2 1 9/ 1 WD1 922 DVG-H EC/F 1~2V,92 62 1 67/6 WD1 92 DVG-H 6EC/F ~V 2,2,7 11 1 7/69 11 WD2 92 DVG-H 6EC/F ~V,6 8 192 1 78/72 11 WD2 92 DVG-H 8EC/F ~V,86 7,7 276 9 81/72 192 WD2 926 DVG-V EC/F 1~2V, 1,8 1 1 6/ WD1 927 DVG-V EC/F 1~2V,92 8 1 6/8 7 WD1 91 DVG-V 6EC/F ~V 2,9,8 12 1 72/67 16 WD2 916 DVG-V 6EC/F ~V, 8 182 16 7/69 11 WD2 917 DVG-V 8EC/F ~V,79 7,7 21 9 7/66 199 WD2 Insulation class, motor F; enclosure class, motor IP
Roof Fan DVG EC Dimensions Accessories DVG EC A B ø E F G ø df (nxm) H1 H 98 12 1 7 8 (6xM8) 67 668 12 1261 8 8 (6xM8) 67 6 9 7 1 1 178 6 (8xM8) 77 6 19 8 1 17 172 67 (8xM8) 88 8 12 1 1 22 128 872 (8xM8) 999 SSGE/F socket silencer DVG-V/F DVG-H/F FDGE/F roof socket FDG/F flat roof socket SSG/F socket silencer ASG/F inflow box ASFV Flange DVG installation examples VKG/F shutter DVG-V DVG-V ASSG/F flexible connection SSG/F Roof base Silencer with silencer ASG/F Inlet chamber VKG/F Automatic shutter ASSG/F Flexible connection DVG-V VKG/F Automatic shutter ASSG/F Flexible connection FDG/F Roof Silencer base DVG-V FTG tilting device (for and, if not intended for fire ventilation) VKG/F Automatic shutter SSG/F SSG/F Roof base with silencer Silencer ASG/F Inlet chamber ASSG/F Flexible connection VKG/F Automatic shutter SSGE/F (FDGE/F) Roof Silencer base with/ without silencer ASG/F Inlet chamber ASSG/F Flexible connection
Roof Fan DVG EC Diagrams with dashed system curves Horizontal exhaust DVG-H EC 1 2 DVG-H EC/F 2 1.2..7 1 8 2 6 1 8 12 DVG-H EC/F DVG-H 6EC/F 6 7 2 2. 1 1. 2 1 2 12 1 1 2 1 1 1 2 2 DVG-H 6EC/F DVG-H 8EC/F 9 7 6 2 2 6 2 6 8
Roof Fan DVG EC Vertical exhaust DVG-V EC 1 2 DVG-V EC/F 2 1.2..7 1 8 2 6 1 8 12 DVG-V EC/F DVG-V 6EC/F 6 7 2 2. 1 1. 2 1 2 12 1 1 2 1 1 1 2 2 DVG-V 6EC/F DVG-V 8EC/F 9 7 6 2 2 6 2 6 8
6 Roof Fan DVG EC Examples of use Beside smoke and heat extraction, DVG EC can also be used for other ventilation purposes Intelligent control system can also control demand fan operation, based on external sensor demands (CO,, humidity, temperature,...). Industry, Car Park Systems Healthcare, Fitness, Gyms Shopping Malls, Showrooms, Kitchen exhaust CO % C
Roof Fan DVG EC 7 DVG EC connection example Fan electronics PC SCADA Modbus Monitoring DVG EC Roof socket Controller for CO level Max. kapacity in case of fire Daily ventilation IR-Fire detector Smoke detector Fire Smoke CO sensor GARAGE Fire alarm system
8 Roof Fan DVG EC Wiring diagrams WD1 (1~2V) Power supply - connection in service switch Control cables - connection in EC controller EC motor prewired WD2 (~V) Control cables - connection in EC controller EC motor prewired Power supply - connection in service switch Connection Functions Max. crossection of power supply wires: 2, mm 2 ( mm 2 without core end sleeves) Cable glands on service switch for power supply: 1xM2x1, Service switch ON-OFF, 6-pole + 1x NC Max. crossection of control wires: 1, mm 2 Cable glands of control part: 2x M2x1, F1 Fault relay F2 Analog input for set value / speed setting F Potentiometer for speed setting F External sensor F Speed output F6 FIRE mode (open = FIRE) F7 Start / Stop switch (open = stop) F8 Modbus connection
Roof Fan DVG EC 9 Electrical accessories - connection examples If the fan is supposed for fire ventilation too, switch to fire mode must be controlled by fire control system. Electrical accessories Accessories (sensors with output -1V) for daily ventilation, controlled by internal PI regulator (integrated in fan) Setup of internal PI regulator via modbus. For use of internal PI regulator two analog signals (-1V) are needed. First one, which defines target (set point) value of regulated property (temperature, humidity, CO2,..) with analog signal connected to AN1 (connection 7 at 1~, 6 at ~) Second one, which defines actual measured value of regulated property (temperature, humidity, CO2,..) with analog signal from sensor, connected to AN2 (connection 11 at 1~, 8 at ~) Temperature controler AL2A1T Systemair-E-D, humidity, temperature sensor Temperature controller AL2A1T Item no. 921 C DSG 2,, 1 differential pressure sensor 7 6 8 1 2 V AC supply 2 System neutral 2 V AC (G+) output, for actuator supply -point output increase -point output decrease 6 1 V DC control output 7 Signal neutral 8 Change-over input 9 Occupancy input 1 External sensor Differential pressure transmitter with built-in PID cotroller MTP 2 on/off, -step manual speed controller / humidity / temperature Systemair-E-D Item no. 19 % C MTV-1/1 controller for manual speed control 12 9 TEMP 1 2 6 7 12 9 or RH% 1 2 6 7 12 9 or CO2 1 TEMP, -1V/-2mA (Jumper) 2 COM/GND RH%, -1V/-2mA (Jumper) - PT 1 + 6 CO2, -2mA 7 COM/GND 8 8 8 CO2, -1V/- (Jumper) MTP 1 Potentiometer for manual speed control CO2RT-R-D sensor Differential pressure DSG 2 DSG Item no. 169 Item no. 17 DSG 1 Item no. 966 EC-Vent control board 1 11 12 9 +2V Brown Output +...1V DC Yellow White + - EC-Vent room unit
1 Roof Fan DVG EC Accessories with built-in PID controller + 12 9-1V DC - IN 2V AC/DC 1 2 6 7 8 9 Differential pressure transmitter with built-in controller with selectable range...1/ / / 1 Pa DMD-C Item no. 179 Accessories for manual control of speed for daily ventilation step manual controller (2 speeds adjustable) MTP 2 Item no. 122 Controller for manual speed control MTV-1/1 Item no. 6 1 7 12 9 - + 1 2 12 9 IN 2V + -1V DC - 1 2 Potentiometer for manual speed control MTP 1 Item no. 271 1 2 Us + - 18 19 1 9 8 11 12 7 6 Accessories for daily ventilation (switches ON-OFF) / Temperature - sensor with built-in relay CO2RT-R-D Item no. 699 C 18 12 19 11 Common Normally open 1 Supply voltage 2 V AC 2 System neutral 2 V AC Normally closed
Roof Fan DVG EC 11 EC Vent % % C C EC-Vent Room Unit Item no. 18 EC-Vent control board Item no. 11 ~ 1~ 6 7 8 Regin CO2RT-D PT 1 PT 1 Signal neutral Out...1V DC CO2 Out...1V DC temperature Out...1V DC humidity System neutral Supply voltage 2V AC/DC 8 7 6 2 1 The wiring of 1~ DVG EC and EC-Vent (the wiring of ~ DVG EC is analogue) The markings of EC-Vent as in instruction (A = power supply, RU = room unit, CB = computer board)
www.systemair.com Systemair d.o.o. May 21