Installation Instructions Model Remote Conventional Zone Module INTRODUCTION The Model from is an intelligent device that connects a single zone of conventional devices to a DLC (FireFinder-XLS System) or FS-DLC (FS- 0 System) device loop. The can power up to fifteen compatible -wire, ionization or photoelectric smoke detectors or it can power one PB-9 Beam Detector. It can also monitor an unlimited number of shorting devices such as waterflow switches, thermal detectors, manual stations, etc. Each can be assigned a custom message using either the Zeus Programming Tool (FireFinder-XLS System) or the FS-CT (FS-0 System). Refer to the Zeus Quick Start Manual, P/N -08, or the FS-0 Programming Manual, P/N -090, as applicable. The alarm verification configuration is used only for non-shorting detectors. The supports Class A and Class B wiring. The module uses one address on the device loop. It does not require any mechanical address programming. Use the DPU Device Programming Unit to program and test the module. FRONT BACK SIDE ALARM 8 9 PROGRAMMING POINTS Figure Module Controls And Indicators The has a multicolor LED, visable through the cover plate, which indicates the condition of the circuit. This multicolor LED displays red for alarm, yellow for trouble, and green for normal operation (See Figure ). PRE-INSTALLATION P/N -080- Setting The Module Address. Using the DPU Device Programming Unit, plug the programming cable into the programming points on the (See Figure ).. Set the address for the by following the instructions in the DPU Manual, P/N -00.
INSTALLATION Remove all system power before installation, first battery then AC. (To power up, connect the AC first, then the battery.) Electrical Connections After you have set the address, connect the field wiring. There are three basic connections to the : initiating devices, DLC or FS-DLC device loop, and VDC power. All terminals are power limited. Initiating Devices (Figures,, and ) The supports one zone of initiating devices in either Class A or Class B. The initiating devices are connected to terminals 8 on the terminal block. The is a polarity insensitive module and terminals and can be connected to either line of the DLC or FS-DLC Device Loop. Figure shows the Class A wiring. Figure shows the Class B wiring. VDC POWER LINE DEVICE LOOP LINE STYLE D (CLASS A) EOL * EARTH 8 9 + - Figure Initiating Devices Wiring Diagram Class A (Style D) Installation * EOL DEVICE IS.K, /W (P/N 0-8088) FOR CANADIAN APPLICATIONS, USE MODEL EL- WITH.K, /W RESISTOR. STYLE B (CLASS B). Wire 8 AWG minimum, AWG maximum, ohms Max.. Supervised, power limited to. Voltage VDC.. Positive and negative ground for terminals -8. EOL* * EOL DEVICE IS.K, /W (P/N 0-8088) FOR CANADIAN APPLICATIONS, USE MODEL EL- WITH.K, /W RESISTOR. VDC POWER LINE DEVICE LOOP LINE 8 9 Figure Initiating Devices Wiring Diagram Class B (Style B) Installation EARTH. Wire 8 AWG minimum, AWG maximum, ohms Max. (both sides). Supervised, power limited to. Voltage VDC.. Positive and negative ground for terminals, 8. P/N -080-
Figure shows the wiring for the PB-9 beam detector. When the PB-9 is used, the -position plug from jumper J must be removed. Follow the steps listed below to remove the -position plug from J: a. Remove the screw from the center of the plastic cover and place it to one side. b. Remove the circuit board and locate jumper J. c. Remove the -position plug from J. d. Reassemble the circuit board and plastic cover using the screw that was removed in the first step. e. Be sure to use the correct end of line device with the in this configuration. BEAM DETECTOR WIRING CLASS B PB-9 DO NOT CONNECT MORE THAN ONE PB-9 TO AN A B C D E F VDC POWER DLC DEVICE LOOP LINE LINE.K, /W EOL RESISTOR P/N 0-808 EARTH 8 9 J NOTE: Positive and negative ground for terminals, 8. Figure Wiring Diagram For PB-9 Installation P/N -080-
9 0 Device Loops (Figures and ) The communicates with the FireFinder-XLS via its DLC device loop. The device loop may be wired Class A or Class B. Figure shows both wiring types. Refer to the DLC Installation Instructions, P/N -0090 for additional wiring information. Do not mix wiring types; Zone and Zone must be the same wiring type.. Loop resistance 0 ohms Max with devices on the loop. Refer to the DLC Installation Instructions, P/N -0090 if the number of devices is less than.. Wire 8 AWG minimum, AWG maximum.. No EOL device required.. Supervised, power limited to. Positive and negative ground for terminals -8 on. NOT USED CC-/CC- 8 LINE (OUT) LINE (RETURN) LINE (RETURN) LINE (OUT) LINE (OUT) LINE (RETURN) LINE (RETURN) LINE (OUT) CLASS A* INSTALLATION NO T-TAPPING ALLOWED 8 9 8 9 8 9 8 9 8 9 8 9 *OPERATES IN FULL CONFORMANCE WITH STYLE. Loop resistance 0 ohms Max with devices on the loop. Refer to the DLC Installation Instructions, P/N -0090 if the number of devices is less than.. Wire 8 AWG minimum, AWG maximum.. No EOL device required.. No jumper required between terminal and, terminal and.. Supervised, power limited to. Positive and negative ground for terminals -8 on. NOT USED 9 0 CC-/CC- 8 LINE LINE LINE LINE CLASS B** INSTALLATION T-TAPPING ALLOWED 8 8 8 9 9 9 **OPERATES IN FULL CONFORMANCE WITH STYLE 8 8 8 9 9 9 Figure Device Loop Wiring Diagram For FireFinder-XLS 8 8 9 9 The communicates with the FS-0 via its FS-DLC device loop. The device loop may be wired Class A or Class B. Figure shows both wiring types. Refer to the FS-0 Installation, Operation and Maintenance Manual, P/N -09, for additional wiring information.. Loop resistance 0 ohms Max with devices on the loop. Refer to the FS- 0 Installation, Operation and Maintenance Manual if the number of devices is less than.. Wire 8 AWG minimum, AWG maximum.. No EOL device required.. When wiring Class B, no jumper required between terminal +OUT and +IN, terminal -OUT and -IN.. Supervised, power limited to. Positive and negative ground for terminals -8 on. FS-DLC Device Loop Circuit FS-DLC Device Loop Circuit LINE (OUT) LINE (RETURN) LINE (RETURN) LINE (OUT) LINE LINE CLASS A* INSTALLATION NO T-TAPPING ALLOWED 8 9 8 9 8 9 *OPERATES IN FULL CONFORMANCE WITH STYLE CLASS B** INSTALLATION T-TAPPING ALLOWED 8 9 8 9 8 9 **OPERATES IN FULL CONFORMANCE WITH STYLE Figure Device Loop Wiring Diagram For FS-0 8 9 P/N -080-
VDC Power (Figure ) In a FireFinder-XLS System, the receives its power from the VDC power output on TB of the PSC- or PSX-. In an FS-0 System, the receives its power from the V power output on the control panel or auxiliary power supply. The VDC power may be wired only as Class B. Since the monitors the power at its screw terminals, you can star or T-tap the power connection. Refer to Figure for the wiring diagram.. Wire 8 AWG minimum, AWG maximum.. No EOL device required.. Supervised, power limited to. A power supply which is resettable, power limited and UL listed for fire protective signaling use and is rated between 8.8-8. VDC.. Positive and negative ground for terminals -8 on. TO VDC SEE NOTE + - Figure VDC Wiring Diagram CLASS B INSTALLATION T-TAPPING ALLOWED 8 9 8 9 8 9 8 9 8 9 Mounting. Mount the in a standard two gang electrical box. The box must have a depth of at least ½ inches.. When the field wiring for the initiating devices, device loop, and VDC is connected, press the into the box and fasten it with the four screws provided.. Attach a dress bezel if necessary, making sure that the ALARM LED is aligned with the hole in the bezel. COMPATIBILITY The devices in Table are listed for use with the. Siemens Detector Model DI-/H DI-A/AH DI-B/BH TABLE COMPATIBILITY Base DT- DB- DB-S with DB-ADPT Installation Instructions DB-S -089-8 DB-S -089-8 -099- -099- AD-I -09- PBA-9 PBB-9-09- PE-/T DB- DB-S with DB-ADPT AD-P -0998-9 -0998-9 -099-9 Use up to fifteen detectors, any combination of those listed. Only one PB-9 (consisting of a PBA-9 detector and PBB-9 base), and no additional devices, can be connected to an. Detector operated accessories cannot be used with the. The model numbers listed are the UL compatibility identifiers. P/N -080-
ELECTRICAL RATINGS Initiating Device Zone: Max. Zone Resistance Supervisory Voltage Range Max. Zone Current ohms total 8-.VDC filtered full wave ma VDC Power Voltage Range Max. Current 8.8-8.VDC 00mA DLC / FS-DLC Loop Max. Current ma P/N -080-
This page has been left intentionally blank. P/N -080-
This page has been left intentionally blank. Florham Park, NJ Siemens Building Technologies, Ltd. Fire Safety & Security Products Kenview Boulevard Brampton, Ontario LT E Canada P/N -080-