Powrmatic / -X Hot Water Heat Emitter Industrial & Commercial Heating Systems www.powrmatic.co.uk +44 (0) 1460 53535 info@powrmatic.co.uk
INDUSTRIAL INDUSTRIAL & COMMERCIAL & COMMERCIAL WARM HEATING AIR HEATING SOLUTIONS CPx The Powrmatic LTHW low temperature hot water heat emitter is a water-supplied suspended air heater which Lorem The ipsum unit has dolor a powerful sit amet, axial consectetur fan which adipiscing means it elit, is suitable sed do for eiusmod many tempor applications. incididunt Powrmatic ut labore offers et dolore a range magna of aliqua. accessories Ut enim allowing ad minim it veniam, to satisfy quis a variety nostrud of exercitation applications. ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat For example, cupidatat the non unit proident, can be made sunt in suitable culpa qui for officia external deserunt air connection mollit anim in combination id est laborumwith filtering and a mixing box for the dilution of fresh external air. The is also compatible with various heat sources including easy connection to new and existing biomass boiler systems. GAS Powrmatic can discharge air horizontally or vertically. G20 - GROUP H / G25 GROUP L OIL 35 SEC FUEL (STANDARD) 28 SEC FUEL (OPTIONAL) LPG PROPANE G31 Models Available - Pre Painted Panels - X - Stainless Steel Casing (Special Order) Casing Constructed of a self supporting galvanized, pre-painted metal or stainless steel (-X). The casing features a modern and attractive aesthetic line. The geometry adopted gives the heater maximum compactness and versatility. Heat Exchanger Constructed of a high efficiency copper tube battery with an aluminum finned exchange coil. Steel water couplings with air vent valves and both fixed on anti-break clamp brackets. Lorem ipsum dolor sit amet Axial Fan ErP compliant low noise, high performance axial fans mounted in a safety protection cage. Featuring a two or three speed motor (model dependent). Adjustable Louvres Warm air is discharged through a series of adjustable louvres so as to optimise both throw and distribution. Biomass Compatability The is compatible with various heat sources including easy connection to new and existing Biomass boiler systems ( not suitable for ground source heat pumps) 2
TYPICAL APPLICATIONS TYPICAL APPLICATIONS Warehouses Factories Garage Horticultural Workshops & Garden Centres Distribution Garage Workshops Centres Distribution / Logistic Centres Aircraft Hangers Showrooms Retail Shops Poultry Houses Construction The unit compromises of high quality components as per the below; Controls The Powrmatic has a range of controls which allow the end user to set a range of fan speeds for single phase and 3-phase units. The controls can be found on page 6. Accessories The Powrmatic comes with a wide range of accessories to further enhance performance and to facilitate various installation options. These accessories can be found on page 6. 1 - Axial fan with safety protection guard 2 - Fan mounting shroud 3 - Aluminium finned copper coil 4 - Main header complete with air vents 5 - Louvred outlet CUSTOMER BENEFITS CUSTOMER BENEFITS Energy efficient heating Lcon sectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore Range of et sizes dolore to suit magna building aliqua. size Duis aute irure dolor in reprehenderit Space in voluptate saving Off velit Floor esse Mounting cillum Lorem ipsum dolor sit Compatible amet, consectetur with Biomass adipiscing heating systems elit, Lcon sectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et Simple dolore and magna quick to aliqua. install 3
Technical Specification Model Heating Capacity (1) Rows Speed Max- Med- Min Fans Max. Air Flow Air Throw (2) Water Pressure Drop Water flow rate Elect supply Elect power Sound pressure db(a) (3) kw RPM m 3 /h m kpa I/h V-50Hz W Max Min -12 11.36 2 1 1750 22 26 785 73 50 41-13 14.76 3 1 1550 17 20 1020 73 50 41-22 15.02 2 1 2450 25 17 1044 105 51 45-23 20.34 3 1 2300 19 20 1401 105 51 45-32 18.71 2 1 2800 31 30 1296 110 52 43-33 24.32 3 1 2550 25 17 1680 110 52 43 1400 900 230 ~ 700-42 23.30 2 1 3600 31 24 1612 130 53 43-43 31.14 3 1 3400 25 19 2141 130 53 43-52 27.10 2 1 3950 32 20 1876 160 53 43-53 36.50 3 1 3900 24 13 2514 160 53 43-62 32.97 2 1 5200 33 13 2300 200 53 47-63 44.70 3 1 4900 26 16 3086 200 53 47-72 40.13 2 1 6700 39 14 2793 245 52 46-73 53.57 3 1 6200 37 12 3707 245 52 46-82 -83 57.22 2 2 8500 38 11 3985 260 54 49 900 400 3N ~ 700 74.80 3 2 7700 32 9 5173 260 53 49-92 75.39 2 2 12550 40 21 5229 500 53 48-93 98.19 3 2 10900 38 17 6764 500 53 48 Notes: (1) Heating: air inlet temperature 15 C, water temperature 80-60 C, relative humidity 50%, atmospheric pressure 1013 mbar, at maximum fan speed. (2) The air flow is measured to a point where the terminal velocity has a speed of 0.2m/s. (3) Sound pressure refers to wall mounted units measured in a free field at a distance of 3 metres. 4
Dimensions 12-93 Model Dimensions mm A B C Fan N kg Model Dimensions mm A B C Fan N kg 12 555 280 390 1 14 13 555 280 390 1 15 22 605 280 440 1 16 23 605 280 440 1 18 32 655 280 490 1 19 33 655 280 490 1 21 42 705 280 540 1 23 43 705 280 540 1 24 52 755 280 590 1 25 53 755 280 590 1 28 62 805 280 640 1 29 63 805 280 640 1 32 72 855 280 690 1 40 73 855 280 690 1 43 82 1.205 280 690 2 58 83 1.205 280 690 2 63 92 1.405 280 690 2 70 93 1.405 280 690 2 76 Notes: - Weights shown above are for standard options - Please contact Powrmatic for -X Weights Water Fitting Dimensions RETURN FLOW Model 12-13 22-23 32-33 42-43 52-53 62 63 72 73 82-83 92-93 A 300 350 400 450 500 550 600 600 600 Ø BSP/Rc 1 1 1 1 1 1¼ 1 1¼ 1¼ 1¼ 5
Accessories 4 1 4 7 5 8 3 6 5 2 8 Controls 9 10 11 12 Descripton Ref No Model Number 12-13 22-23 32-33 42-43 52-53 62-63 72-73 82-83 92-93 Support Brackets 1 -SB Vertical Louvres 2 -VL1 -VL2 -VL3 -VL4 -VL5 -VL6 -VL7 -VL8 -VL9 Ceiling Mounting Kit 3 -CMK1 -CMK2 -CMK3 -CMK4 -CMK5 -CMK6 -CMK7 -CMK8 -CMK9 Inlet Hood 4 -IH1 -IH2 -IH3 Air Filter 5 -AF1 -AF2 -AF3 -AF4 -AF5 -AF6 -AF7 -AF8 -AF9 Support Brackets (Filter) 6 -SBF Mixing Box 7 -MB1 -MB2 -MB3 -MB4 -MB5 -MB6 -MB7 -MB8 -MB9 Support Brackets (F/MB) 8 -SBMB 3 Speed Control 9 -SC12 -SC13 n/a n/a n/a Room Thermostat 10 -RT Speed Changeover Switch 11 n/a n/a n/a n/a n/a n/a -SCS Speed Control Panel 12 n/a n/a n/a n/a n/a n/a -SCP Support brackets - for support and anchorage made of galvanised steel. Vertical Louvres - made of galvanized steel ( version), stainless steel (-X version) Ceiling mounting Kit - mounting onto ceiling Inlet Hood- for mounting on the fresh air intake in case of outside installation. Air filter- to treat and filter the intake fresh air or room inlet air with a plenum containing filtering cells, to be mounted inside the unit. Support brackets (filter) - for support of the unit with a filter kit in case of fresh air intake. Mixing Box - for the complete or partial renewal of the fresh air. The kit is composed of an air inlet plenum, two dampers connected by a connection device. Support brackets (F/MB) for support of the unit and the mixing chamber kit or the air filter kit 3-speed control - only for single phase models (STOP - I - II - III ). Room thermostat- single stage, with ON-OFF switch. Speed changeover switch - 2-modes speed control (STOP-MIN-MAX), only for three phase models. Speed Control Panel - with speed changeover switch, with 3-mode air speed switch settings, complete with fittings and connectors; only for three-phase models. 6
Installer Guide General The following notes are provided as a guide, however installers and operators should fully acquaint themselves with the more detailed guidance provided in the relevant installation manual. For copies of such manuals please consult our technical department or visit our website - www.powrmatic.co.uk Standards Units must be installed, commissioned and operated with due regard to appropriate regulations, relevant Codes of Practice which may include but is not limited to BS6880 and any possible requirements of Local Authorities, Fire Officers and insurers as well as Powrmatic s installation manual. Position & Location heat emitters are specifically design to operate in conjunction with a pumped hot water supply. units can be mounted either horizontally using support brackets or vertically on suitably sized drop rods. It is important that all supporting structures have due regard to the relevant weight loadings and provide stability so as to protect the integrity of flow and return water connections. Units should be sited so as to provide heat into the relevant working zones and where a general pattern of effective air circulation can be achieved. For specific siting recommendations please consult our technical department. heat emitters are suitable for a wide variety of industrial, commercial, horticultural or poultry applications however if units are to be sited in areas of high humidity, where dust may be present or a corrosive atmosphere then please consult our technical department. Installation Particular clearances may be necessary for the correct and safe function of the heat emitter as well as for maintenance purposes. Such clearances are confirmed in the relevant installation manual. It is important that units are installed in such a way that they are level in both front to rear and side to side planes. When connecting pipework installers should ensure that the direction of flow is correct. The installation of local isolating valves, service unions and strainers is recommended. Where emitters are installed in the horizontal plane, that is for downward discharge then it is highly recommended that a valve and actuator be installed within the pipework so as to isolate the water flow when the fan is not operating, failure to do so will allow heat to rise and overheat the fan motor. For further advice please consult our technical department. Electrical connections should comply with IEE regulations and include an isolator local to each emitter. Water Treatment Water quality used with heat emitters can have a significant effect on both efficiency and reliability. It is recommended that installers consult and follow the advice within the Water Treatment and Conditioning of Commercial Heating System Guide available via the ICOM Energy website www.icom.org.uk Guarantee Powrmatic units are provided with a guarantee. For United Kingdom sales the heater has the benefit of a 12 month parts only guarantee. All guarantees are subject to terms and conditions. 1 YEAR PARTS ONLY WARRANTY 7
Powrmatic are a leading British manufacturer of industrial and commercial heating equipment. With over 60 years of experience in the HVAC industry, our products are built with integrity, and characterised by high quality and energy-saving designs, delivering exceptional performance and facilitating compliance with energy and emission regulations. Powrmatic are also a specialist British manufacturer of natural, powered and smoke ventilation products working closely with a wide range of architects and consultants whilst also a supplier of a range of air conditioning and evaporative cooling equipment. We provide a full product application advice service for architects, mechanical engineers, installers and end users to ensure the best products are selected to meet the required budget, design and regulatory requirements. Our heating and ventilation engineers are also supported by distribution partners and a network of installers who are knowledgeable in the supply, installation and maintenance of all of our equipment. Get in touch United Kingdom Office Powrmatic Limited Hort Bridge Ilminster Somerset TA19 9PS tel: +44 (0) 1460 53535 fax: +44 (0) 1460 52341 e-mail: info@powrmatic.co.uk web: www.powrmatic.co.uk Ireland Office Powrmatic Ireland 45 Broomhill Close Tallaght Dublin 24 tel: +353 (0) 1452 1533 fax: +353 (0) 1452 1764 e-mail: info@powrmatic.ie web: www.powrmatic.ie FOR THE LATEST NEWS, CASE STUDIES, AND TECHNICAL SUPPORT FOLLOW US ON #keepingthenationwarm ICOM Energy Association EURO-AIR QUALITY Powrmatic pursues a policy of continues improvement in both design and performance of its products and therefore reserves the right to change, amend or vary specifications without notice. Whilst the details contained herein are believed to be correct they do not form the basis of any contract and interested parties should contact the Company to confirm whether any material alterations have been made since publication of this brochure. Issue 5.3 2017