SHIPBOARD ELECTRIC CONVECTION OVEN ECOD-AT, ECODL-AT ECOF-AT, ECOFL-AT

SHIPBOARD ELECTRIC CONVECTION OVEN ECOD-AT, ECODL-AT ECOF-AT, ECOFL-AT Installation and Operation Instructions 2M-W483 Rev. E 3/8/3 ECOF-AT

SAFETY SYMBOL These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance. FOR YOUR SAFTEY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINTIY OF THIS OR ANY OTHER APPLIANCE. POST IN PROMINENT LOCATION INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS. THIS INFORMATION SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS SUPPLIER. AS A MINIMUM, TURN OFF THE GAS AND CALL YOUR GAS COMPANY AND YOUR AUTHORIZED SERVICE AGENT. EVACUATE ALL PERSONNEL FROM THE AREA. WARNING IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT. WARNING RISK OF FIRE OR ELECTRIC SHOCK DO NOT OPEN WARNING, TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE CONTROL PANEL. NO USER-SERVICABLE PARTS INSIDE. REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY. NOTICE Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all liability. Lang reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Due to periodic changes in designs, methods, procedures, policies and regulations, the specifications contained in this sheet are subject to change without notice. While Lang exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the specifications. By using the information provided, the user assumes all risks in connection with such use. MAINTENANCE AND REPAIRS Contact your local dealer for service or required maintenance. Please record the model number, serial number, voltage and purchase & Installation Information in the area below and have it ready when you call to ensure a faster service. Model No.: Serial No.: Voltage: Purchased From: Location: Purchase Date: -Phase or 3 Phase: Installed Date: 2

Table of Contents Chapter...Page. Table of Contents...3 2. List of Illustrations...3 3. Specifications...3 4. Equipment Description...4 5. Installation...5 6. Operation...7 7. Maintenance & Troubleshooting Procedures... 8 8. Parts List...5, 7, 9, 2, 23 List of Illustrations Fig# Title of Illustraion...Page #. Picture of Oven...Cover 2. Leg Installation...6 3. Stacking Instructions...6 4. Wiring Diagram 208/240 VAC... 5. Wiring Diagram 440 VAC...2 6. Exploded View... 4, 6, 8, 20, 22 NOTICE: Service on this, or any other, LANG appliance must be performed by qualified personnel only. Consult your LANG authorized service agent directory or call the factory at 34-678-635, or www.langworld.com for the service agent nearest you. SPECIFICATIONS: Lang Model Previous Model Height x Width x Depth Clearance from conbustible surface Actual Weight Shipping Freight Class ECOD-AT ECO-6M 25.0 x 38.0 x 45.2 635mm x 966mm x 48mm 380 lbs. 73 kg 430 lbs. 95 kg ECOF-AT ECOD-AT ECODL-AT ECOF-AT ECOFL-AT ECO-7M ECO-8M ECO-9M 25.0 x 38.0 x 38.2 635mm x 966mm x 970mm 50.0 x 38.0 x 45.2 270mm x 966mm x 48mm 50.0 x 38.0 x 38.2 270mm x 966mm x 970mm Side: 6 (53mm) Back: 6 (53mm) Floor: 6 (53mm) 360 lbs. 64 kg. 820 lbs. 373 kg 780 lbs. 355 kg 40 lbs. 86 kg 870 lbs 395 kg 830 lbs. 377 kg 70 Lang Model Single Stack ECOD-AT ECOF-AT Double Stack ECOD-AT, ECODL-AT ECOF-AT, ECOFL-AT Previous Model ECO-6M ECO-7M ECO-8M ECO-9M Volts AC - Hz Total kw L L2 L3 Amps - Ph 208-50/60 36 36 23 55.3 240-50/60 28 28 26.5 48 380-50.5 20 20 2.5 N/A 440-50/60 7 7 N/A 480-50/60 6 6 0 N/A 208-50/60 59 72 59 240-50/60 55 56 55 96 380-50 23 30 3.5 30 N/A 440-50/60 28 34 28 N/A 480-50/60 26 32 26 N/A 3

EQUIPMENT DESCRIPTION INTRODUCTION This manual contains the necessary information to install, operate, maintain, and service the Lang model ECO convection ovens. Replacement parts should be genuine Lang parts. Failure to use genuine Lang replacement parts may result in malfunction of the appliance or possible injury to the contractor or service technician. PURPOSE AND FUNCTION Convection ovens constantly circulate air over the product. This removes a layer of moisture and cool air from around the product. This allows heat to penetrate the product more quickly. Cooking times are shortened and cooking temperatures are reduced. CAPABILITIES This convection oven is suitable for cooking all types of products requiring baking or roasting. ENVIRONMENTAL REQUIREMENTS The following minimum spacing from combustible surfaces must be maintained: Sides 2 inches, Back 2 inches ITEMS FURNISHED (Listed by Model Number) SINGLE STACKED UNITS ECOD-AT ECO-6 or ECO-6M (Previouse Model) ea. Oven, Type I, Size 2 4 ea. Legs 6 ea. 3/8 6 x 5/8 Bolts (For mounting legs) 6 ea. 3/8 6 Hex Nuts (For mounting legs) 32 ea. Washers (For mounting legs) 2 ea. Rack Slides, Extra Deep 5 ea. Racks, Extra Deep 2 ea. Manuals, Technical ECOD-AT or ECOF-AT ECO-7 or ECO-7M (Previouse Model) ea. Oven, Type I, Size 4 ea. Legs 6 ea. 3/8 6 x 5/8 Bolts (For mounting legs) 6 ea. 3/8 6 Hex Nuts (For mounting legs) 32 ea. Washers (For mounting legs) 2 ea. Rack Slides, Standard Depth 5 ea. Racks, Standard Depth 2 ea. Manuals, Technical DOUBLE STACKED UNITS ECOD-AT, ECODL-AT or ECOF-AT, ECOFL-AT ECO-8 or ECO-8M (Previouse Model) 2 ea. Oven, Type II, Size 2 4 ea. Legs 6 ea. 3/8 6 x 5/8 Bolts (For mounting legs) 6 ea. 3/8 6 Hex Nuts (For mounting legs) 32 ea. Washers (For mounting legs) 4 ea. Rack Slides, Extra Deep 0 ea. Racks, Extra Deep 2 ea. Manuals, Technical ea. Stacking Kit ECOD-AT, ECODL-AT or ECOF-AT, ECOFL-AT ECO-9 or ECO-9M (Previouse Model) 2 ea. Oven, Type II, Size 4 ea. Legs 6 ea. 3/8 6 x 5/8 Bolts (For mounting legs) 6 ea. 3/8 6 Hex Nuts (For mounting legs) 32 ea. Washers (For mounting legs) 4 ea. Rack Slides, Standard Depth 0 ea. Racks, Standard Depth 2 ea. Manuals, Technical ea. Stacking Kit 4

ITEMS REQUIRED An adequate supply of wire suitable for the loads and application specified on the data sheet must be provided. The data sheet is on Page 4 of this manual. TOOLS AND TEST EQUIPMENT REQUIRED For Installation: set Open End Wrenches Flat Blade Screwdriver Phillips Screwdriver Wire Cutter/Stripper AMP Probe Voltmeter Drill 4 #27 Drill Bits For Service: All of the above plus Needle Nose Pliers Crimping Pliers Allen Wrench Set Temperature Meter Very Small Flat Blade Screwdriver #0 Square Drive Screwdriver INSTALLATION CAUTION CAUTION DANGER WARNING NOTICE: NOTICE: THE OVEN IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE PLACE OF INSTALLATION. ANY STAND, COUNTER OR OTHER DEVICE ON WHICH OVEN WILL BE LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE OVEN(S). SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT. THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED. FAILURE TO GROUND THE APPLIANCE COULD RESULT IN ELECTROCUTION AND DEATH. INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING. IMPROPER INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE CODES. The data plate is located on the door of the oven. The oven voltage, wattage, serial number, wire size, and clearance specifications are on the data plate. This information should be carefully read and understood before proceeding with the installation. The installation of any components such as a vent hood, grease extractors, fire extinguisher systems, must conform to their applicable National, State and locally recognized installation standards. 5

INSTALLATION INSPECTION AND INSTALLATION Upon receipt of the oven(s) any damage should be noted on the Bill of Lading and countersigned by the carrier. If concealed damage is discovered the carrier should be notified. All claims must be filed with the carrier. Move the crate(s) containing the oven(s) as close to the place of installation as possible before removing the protective crating. Uncrate the oven(s) and move them as close as practical to the final installation site. Bolt the legs to the bottom oven, (See figure #2). Use the 3/8 6 x 5/8 Bolts, Hex Nuts and Washers provided. There are pre-punched holes provided in the legs and oven bottom to aid in leg installation. Now the oven can be set upright in or near its final position. SINGLE OVENS: Connect power throught the knockout on the bottom of the unit. The oven can be placed in its final position and leveled. The oven is ready for initial start-up procedures now. (See page 7) STACKED OVENS: Be careful to route the power supply wire between the two ovens using the holes provided. Do not pinch or cut the supply wires when stacking the ovens. Use the stacking kit provided to secure the top oven to the bottom oven. The stacking kit contains four (4) identical corner braces, one brace goes on each corner. Drill pilot holes for the mounting screws using the pre-punched holes as a guide. Secure the top oven to the bottom oven with the sheet metal screws provided. (See figure #3) Connect the power supply leads from the top oven to the power supply leads of the bottom oven and incoming power per the wiring diagram on Page or 2. Now the bottom oven can be connected to the incoming power supply through the knockout provided in the bottom of the oven. Be sure the power supply voltage matches the voltage specified on the nameplate located on the front of the oven! Then the oven can be placed in its final position and leveled. The oven is ready for initial start-up procedures now. See page 7. Flange Leg Oven Bottom Nut 3/8-6 Hex Lock Washer Washer Figure 2, Bolting Legs to bottom oven Top Oven Bolt 3/8-6 x 5/8 Corner Brace IL32 Bottom Oven IL322 Figure 3, Securing the top & bottom ovens together. 6

OPERATING INSTRUCTIONS NOTICE: CAUTION CAUTION During the first few hours of operation you may notice a small amount of smoke coming off the oven, and a faint odor from the smoke. This is normal for a new oven and will disappear after the first few hours of use. ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM COMBUSTIBLE MATERIALS. KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR FALLS. Each oven has the following controls: Vent Pull to Open, Push to close. Timer Adjust to desired setting. Temperature Turn to desired cooking temperature. Power Switch Pull up to turn oven ON, push down to turn oven OFF. Light Switch Pull up to turn oven light ON, release and oven light goes out automatically. Motor Speed Switch Pull up for High Speed, push down for low speed. INITIAL START-UP Set oven(s) at 350 F and allow oven to operate empty for 3 hours, prior to initial use. NORMAL OPERATION Turn the Power Switch On, turn to the desired temperature and select motor speed. (Hi or Low) 7

MAINTENANCE Wash the stainless interior & exterior often with a solution of hot water and mild detergent to prevent grease build-up and preserve the oven s appearance. The oven racks, slides and stainless steel oven liners are removable for easier cleaning of the oven interior. NOTE: Wipe up spillage as soon as possible. Never use scouring powder. It is difficult to remove completely and a residue build-up can damage the oven. WARNING CAUTION NOTICE: WARNING CAUTION KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY OR HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC. MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND PROTECTIVE CLOTHING. CAREFULLY READ THE WARNING AND FOLLOW THE DIRECTIONS ON THE LABEL OF THE CLEANER TO BE USED. Service on this, or any other, LANG appliance must be performed by qualified personnel only. Consult your authorized service station directory or call the factory at 34-678-635, or www.langworld.com For the service station nearest you. BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE RECEPTACLE. BEFORE REPLACING ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC POWER SUPPLY. USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND WILL VOID ALL WARRANTIES. TROUBLESHOOTING GUIDE SYMPTOM PROBLEM REMEDY Internal Circuit Breakers Off Turn on Power supply circuit breakers off Turn on Oven will not turn on Improperly Phased Phase per wiring diagram Fuse Open Change fuses Supply circuit breakers of insufficient size Install proper size breakers Power Supply Circuit Breakers Trip Supply voltage & oven voltage do not Change voltage to match oven match Supply voltage & oven voltage do not Internal circuit breakers trip Change voltage to match oven match Oven takes to long to bake and will not maintain temperature Improperly Phased Phase oven to match power supply per wiring diagram 8

MAINTENANCE and TROUBLESHOOTING CONT D PERFORMANCE AND INSPECTION A periodic check of thermostat calibration should be performed. To check oven calibration attach a thermocouple to the mid-point of the thermostat bulb in the oven cavity. Turn the temperature dial to 350 F and turn the oven ON. Wait approximately 20 minutes until the oven temperature has stabilized. If the average of the ON and OFF thermostat readings is within 0 F of 350 F the oven is in calibration. If not, remove the temperature knob and turn the small screw in the middle until oven is in calibration. Replace the knob and the oven is ready for normal operation. MAJOR COMPONENT DISASSEMBLY, REPAIR, REPLACEMENT & REASSEMBLY (Refer to figure #4, page 22) THERMOSTAT, CONTACTORS (RELAYS), SWITCHES These parts are located behind the control panel assembly on the right hand side of each oven. Remove the screws attaching the control panel to the front of the oven. Slowly pull out the control panel until the component requiring replacement is accessible. THERMOSTAT REPLACEMENT: Inside the oven cavity remove the retaining clips holding the thermostat-sensing bulb in place. Feed the bulb through the oven wall into the control panel area. Remove the wires attached to the thermostat terminals. Remember the terminal each wire was on and attach the wires to the same terminal on the new thermostat. Remove the screws holding the old thermostat to the front of the control panel. Discard old thermostat. Mount the new thermostat to the control panel, carefully feed the sensing bulb through the oven wall, and reattach the sensing bulb to the oven side using the retaining clips removed earlier. Close control compartment. Restore power to oven. Refer to the Performance and Inspection section to verify proper operation of the new thermostat. ELEMENT REPLACEMENT: The element is located inside the oven cavity. To replace the element, remove the baffle at the back of the oven. This will expose the elements to plain view and allow easy access. Remove the element mounting screws located near the top of the oven. Gently, pull the element into the oven cavity. There is enough wire connected to the element to allow easy access to the terminals located behind the element mounting plate. Move each wore from the existing terminal to the corresponding terminal on the new element. DO NOT mix up these wires! After all wires are transferred to the new element, feed the wire back through the access hole in the back of the oven and attach the element to the oven wall with the screws removed earlier. Replace the baffle. Refer to the Initial Start-up section to restore the oven to proper operation. CONTACTOR (RELAY), SWITCH REPLACEMENT: Pull out control panel as previously outlined. Remove the wires from the contactor or switch being changed. Place those wires on the corresponding terminal of the new part. Remove old part and mount new part with wires attached in the spot where the old part used to be. Reinstall the control panel, restore power to the oven. Turn oven on, set thermostat to 200 F and allow oven to cycle 3 times or until the technician is satisfied with the proper operation of the oven. BLOWER WHEEL REPLACEMENT: The blower wheel is located inside the oven cavity. To replace the blower wheel, remove the baffle at the back of the oven. This will expose the blower wheel to plain view and allow easy access. Loosen the two (2) set screws holding the blower wheel onto the motor shaft. Using a three-finger blower wheel puller, grasp the puller ring with all three fingers and tighten the puller until the blower wheel hub clears the motor shaft. Place new blower wheel on the motor shaft and position exactly 5/8 from the oven back motor plate. Tighten the set screw positioned over the flat on the motor shaft. Spin the fan to make sure it spins straight. Tighten the second set screw and re-tighten the first set screw. Replace the baffle. The oven is now ready to re-start. 9

MAINTENANCE and TROUBLESHOOTING CONT D MOTOR REPLACEMENT: The motor is located inside the oven cavity. To replace the motor, remove the baffle at the back of the oven. This will expose the blower wheel and motor shaft to plain view and allow easy access. Remove the blower wheel as described in BLOWER WHEEL REPLACEMENT. Next, remove the bolts holding the motor plate to the back wall of the oven cavity. Gently pull the motor forward and lay on the bottom of the oven cavity. Mark the wires so they can be placed on the same terminals of the new motor. Remove the motor wires. Remove the motor from the oven. Remove the motor mounting bolts, remove the old motor and replace with the new one. Reveres the above steps to remount the motor and see BLOWER WHEEL REPLACEMENT for proper re-installation of the blower wheel. TRANSFORMER REPLACMENT: Pull out control panel as previously outlined. Mark the wires attached to the transformer. Remove the wires. Remove the screws holding the transformer to the control panel. Install the new transformer. Reconnect the wires making sure they are attached to the same terminals as on the original transformer. Reinstall the control panel, restore power to the oven. The oven is now ready for normal operation. MICROSWITCH REPLACEMENT: Open the oven doors and remove the screws from the micro switch cover located below the doors. Remove the micro switch cover. Remove the two (2) small screws (6/32) holding the micro switch to its mount. Mark the wires attached to the micro switch, then remove the wires. Attach the wires to the new micro switch. Mount the micro switch with the two 6/32 screws. Adjust the micro switch arm for proper switch actuation. Replace cover and restart oven. 0

2 3 4 BOTTOM DECK CIRCUIT BREAKERS GROUND LUG LANG MANUFACTURING INT. INC. # 0 SUNNEN DRIVE ST. LOUIS, MO. 6343, USA THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L INC. NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED MATERIAL FINISH DR: JMM CK. DATE: TOLERANCE: UNLESS NOTED:.xxx ±.05 ANGLES ± 6/9/2009 SHEET OF 2 REVISIONS MODEL NO. TITLE PART NO. 2M-6-30 WD ECO MIL 208/240V OR 3 PHASE REV. DATE/ECO DESCRIPTION OF CHANGE DR B C D 6/23/2009 ECO 7929 2/30/2009 ECO 8842 0/6/202 ECO 2263 REINSTATED OBSOLETE P/N OB-6-30 JMM WIRE 48 WAS 27 JMM ADDED NOTE FOR BLACK LEAD CONNECTIONS. JMM POWER SWITCH OVEN LAMP SWITCH OVEN LAMP MOTOR SPEED SWITCH 2 3 7 5 6 HEATING ELEMENTS TERMINALS AMPS KW VOLTS TOTAL L L2 L3 PHASE DECK 208.5 36 36 23 55.3 TOP DECK WIRING IDENTICAL TO BOTTOM DECK 2 3 4 34 22 33 35 37 37 33 32 REAR VIEW 8 4 9 FUSE 23 36 FUSE 29 24 RED 26 T BLUE DOOR SWITCH LEFT 3 T2 25 T4 C MOTOR NO DOOR SWITCH RIGHT 30 NC C NO NC 3 CONTACTOR 4 2 3 WHT 7 5 BLK 7 BLU 40 2 RED C 48 27 2 C NO LIMIT THERMOSTAT 20 9 DECK 240.5 28 28 26 48 2 DECK 208 23.0 59 72 59 2 DECK 240 23 55 56 55 96 SERVICE CONNECTIONS SINGLE PHASE THREE PHASE L L2 L3 L L2 DECK,4 2 3,3 2,4 2 DECK,4,7 2,5,8 3.6,3,5,7 2,4,6,8 2 3 4 TOP DECK CIRCUIT BREAKERS 0 CONTACTOR HEATER PILOT LAMP 8 9 6 4 9 8 6 4 RED BLU BLK WHT 29 Figure 4 38 39 REGULATING THERMOSTAT 28 WIRE NUT D NOTE: BLACK LEAD #5 & #6 ARE NOT CONNECTED ON 240V MODELS 5 6 7 8 L L2 2 L3 3 BOTTOM DECK TERMINAL BLOCK 5 6 7 8 L L2 2 3 2 3 4 SINGLE PHASE

L L2 L3 VOLTS KW AMPS L-L2 L2-L3 L3-L TOTAL L L2 L3 PHASE DECK 380 6.6 2.75 2.75.66 20 20 2.5 N/A DECK 440 4.33 3.67 3.67.66 5 5 4.5 N/A DECK 48 0 5.5 2.75 3.2.5 5.8 5 0.8 N/A 2 DECK 380 8.9 8.9 5.5 23.33 33 4 33 N/A 2 DECK 440 7.33 23.33 30 3.5 30 N/A SERVICE CONNECTIONS THREE PHASE SINGLE PHASE L L2 L3 L L2 DECK,4 N/A N/A 2 DECK,4,7 2,5,8 3.6 N/A N/A 2 3 TOP DECK WIRING IDENTICAL TO BOTTOM DECK TRANSFORMER TOP DECK TERMINAL BLOCK CIRCUIT BREAKER 2 6 4 5 5 42 FUSE # 2 3 2 3 2 3 BOTTOM DECK TERMINAL BLOCK BOTTOM DECK TERMINAL BLOCK GROUND LUG STAR MANUFACTURING INTERNATIONAL INC. # 0 SUNNEN DRIVE ST. LOUIS, MO. 6343, USA THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L INC. NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED 34 OVEN LAMP SWITCH 37 37 43 44 33 POWER SWITCH 35 240 480 (380) 36 FUSE #2 24 47 CONTACTOR 2 23 50 CONTACTOR 9 0 20 29 38 Figure 5 MATERIAL FINISH DR : JMM CK. DATE : 6/9/2009 TOLERANCE: UNLESS NOTED:.xxx ±.05 SHEET OF ANGLES ± REVISIONS MODEL NO. TITLE PART NO. 2M-6-3 WD ECO MIL 380V, 440V (480V) REV. DATE/ECO DESCRIPTION OF CHANGE DR F 6/23/2009 ECO 7929 ADDED HI LIM IT CONTACTOR PER UL JMM G /5/2009 ECO 854 REVISED TERMINAL BLOCK AND CONTACTOR REFERENCE JMM H 2/7/2009 ECO 8842 REVISED AND ADDED MISSING WIRE NUMBERS JMM OVEN LAMP J /29/202 ECO 2382 UPDATED VOLTAGE, KW, & AMP INFO.; REMOVED SINGLE PHASE INFO JMM K 2//202 ECO 247 ADDED DECK 480V DATA TO TABLE JMM 33 MOTOR SPEED SWITCH 2 SPEED CONTROL 32 29 45 BLUE T4 52 53 3 C NO NC DOOR SWITCH LEFT T T2 C 4 MOTOR NO DOOR SWITCH RIGHT NC 30 46 RED 2 RED 4 3 WHT 7 BLU 40 5 BLK 48 27 HEATER PILOT LAMP LIMIT THERMOSTAT 8 9 6 42 6 8 4 9 BLK BLU WHT RED 4 39 28 WIRE NUT ONLY WIRE 3 ELEMENTS FOR 440V 3 5 6 4 2 7 8 9 REGULATING THERMOSTAT HEATING ELEMENTS TERMINALS REAR VIEW K 8 2 3 8 2

This page intensionally left blank, so the following pages face each other. 3

2 8 3 4 5 8 6 7 SEE DETAIL A 0 9 SEE DETAIL B Figure 6a Model: ECOF-ATM Electric Marine Convection Oven ECO-7M Electric Marine Convection Oven 4 SK2257 Rev. - 6/2/07

PARTS LIST Model No: ECOD-AT, ECODL-AT, ECOF-AT, ECOFL-AT SHIPBOARD ELECTRIC CONVECTION OVEN March 8, 203, Rev E Key Number Part Number Qty Per Description Q9-ECO-47 TOP-TOP DECK ECOF Q9-ECO-472 TOP-BOTTOM DECK ECOFL Q9-ECO-477 TOP-TOP-DECK DEEP OVEN ECOD Q9-ECO-478 TOP-BOTTOM DECK DEEP ECODL Q9-ECO-47- TOP FRONT - TOP DECK - HATCHABLE 2 Q9-ECO-47-2 TOP REAR - TOP DECK - SUB HATCHABLE 3 2P-7090-0 PLG BTN BLKPLSTC DP-000 ECOD-AT-440G, ECODL-AT440M, ECOFL-AT208M, ECOFL-AT440M 2P-7090-0 2 PLG BTN BLKPLSTC DP-000 ECOF-AT-480M, ECOD-AT-480M 4 Q9-ECO-437 DAMPER PIVOT ALL 5 Q9-ECO-446 DAMPER ROD A ECOF Q9-ECO-46 DAMPER ROD A - DEEP ECOD 6 2C-2003-02 2 SCRW SM PLT 0 X.5 PHLSL HATCHABLE 7 Q9-ECO-479- BTM COVER BTM DECK ONLY - HATCHABLE 8 Q9-ECO-77 BODY WRAP ASSY ECOF Q9-ECO-77- BODY WRAP DEEP ASSY ECOD 9 Q9-ECO-96- FRONT ASSY - SUB ALL 0 Q9-ECO-203 SWITCH DOOR ASSY ALL 2R-7070-25 KNOB DAMPER BLACK PLAIN ALL RACKS NI 2B-50200-20 5 RACK ECCO/GCCO OVEN ECOF NI 2B-50200-3 5 RACK ECO DEEP OVEN ONLY ECOD NI 2B-50200-32 2 RACK SLIDE 5 POS ECO OVEN ECOF NI 2B-50200-33 2 RACK SLIDE 5 POS ECO DEEP ECOD IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. PAGE OF 5

Front 2 3 4 5 6 7 SEE DETAIL C Figure 6b Model: ECOF-ATM Electric Marine Convection Oven ECO-7M Electric Marine Convection Oven SK2258 Rev. - 6/2/07 6

PARTS LIST Model No: ECOD-AT, ECODL-AT, ECOF-AT, ECOFL-AT SHIPBOARD ELECTRIC CONVECTION OVEN March 8, 203, Rev E Key Number Part Number Qty Per Description 2 Q9-ECO-423 VENTS ASSY ALL 3 Q9-ECO-435 VENT CAP - MILITARY ALL 4 Q9-ECO-449 DAMPER ROD B ASSY ALL 5 Q9-ECO-39 MOTOR MOUNT ASSY 440/480V 440V/480V Q9-ECO-39- MOTOT MOUNT ASSY 208V 208V 6 Q9-ECO-72 REAR FIREWALL ASSY ALL 7 Q9-ECO-84 BODY BACK ALL ELEMENTS NI 2N-090-8 ELMNT ECCO 480V KW 480V NI 2N-090-30 ELE 45 440VKW 440V, 380V NI 2N-090-6 ELE ECCO OVN 208/240V KW 208/240V IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. PAGE OF 7

63 63. 32 55 53 44 45 SEE DETAIL D 39 38 43 47 46 6 60 37 34 35 33 36 42 4 40 59 58 5 57 62 0 54 53 55 52 56 48 49 4 39 50 5 49 Figure 6c DETAIL A Typical Door Assy 8 SK2260a

PARTS LIST Model No: ECOD-AT, ECODL-AT, ECOF-AT, ECOFL-AT SHIPBOARD ELECTRIC CONVECTION OVEN March 8, 203, Rev E Key Number Part Number Qty Per Description 32 2C-2009-25 4 SCRW S/S 0-32 X 3/4 T/H ALL 33 2C-2020-07 4 WSHR FLT /4 SAE PLTD ALL 34 2C-2030-29 4 NUT HEX ACORN /4-20 S/S ALL 35 2C-2002-04 4 SCRW PHD ST 8-32X.5 PLTD ALL 36 Q9-ECO-595 2 ECO DOOR HANDLE ALL 37 2R-50800-9 2 DOOR HANDLE ALL 38 Q9-ECO-200-3 DOOR CATCH ASSY - SUB ALL 39 2C-2009-04 2 SCRW THD MS SS 0-32X3/8 ALL 40 2C-205-0 0 SCRW S/S 8-32X/2 P/H S/T ALL 4 Q9-ECO-507 4 HINGE PIN WELD - ECO ALL 42 2C-2009-5 8 SCRW PHD MS SS 0-32X/2 ALL 43 Q9-ECO-557 4 HANDLE SPACER ALL 44 2R-70602-03 2 CATCH DOOR MAGNET 3 PC ALL 45 Q9-ECO-533 2 MAGNET BACKER ALL 46 2C-200-0 4 SCRW THD MS /4-20X2 /4 ALL 47 2C-2020-07 4 WSHR FLT /4 SAE PLTD ALL 48 Q9-ECO-563 4 RETAINER ALL 49 2C-20306-03 0 AVK CAD 0-32 ST GRP ALL 50 Q9-ECO-572 RH DOOR VANE ASSY S/S ALL 50 Q9-ECO-584 LH DOOR VANE ASSY S/S ALL 5 2C-2003-02 AR SCRW SM PLT 0 X.5 PHLSL ALL 52 Q9-ECO-777-2 SWITCH CAM ASSY - /2 ALL 53 2C-2009-30 8 SCRW MS SS 0-32 X.75 PH ALL 54 2P-7020-9 4 BRNZBRFLN/2IDX5/8ODX3/8 ALL 55 Q9-ECO-508- HINGE BOTTOM RH - ECO ALL Q9-ECO-508-2 HINGE BOTTOM LH - ECO ALL Q9-ECO-508-3 HINGE TOP LH - ECO ALL Q9-ECO-508-4 HINGE TOP RH - ECO ALL 56 Q9-ECO-782 SWITCH BOX COVER ALL 57 Q9-ECO-786 2 SWITCH BRACKET MILITARY ALL 58 2C-200-7 4 SCRW RND MS 6-32X PLTD ALL 59 2E-3030-02 2 SWT MICRO #2HLT-5 UNIMAX ALL 60 2C-2030-0 4 NUT HEX 6-32 PLTD ALL 6 2K-7080-03 SNAP BUSH 3/8 SB375-4 BLK ALL 62 2C-390-0 CABLE TIE MOUNT ALL 63 Q9-ECO-200-2 DOOR LATCH ASSY - SUBMARINE 63. Y9-50307-24 - LATCH ASSY - DOOR MARINE NI 2H-6006-3 2 INSULATION KIT ECO DOOR ALL NI 2Q-730-04 2 WINDOW ASSY 9-5/8X6-5/8 ALL NI Q9-6002-2022 DOOR ASSY ECO RIGHT HAND ALL NI Q9-6002-202 DOOR ASSY ECO LEFT HAND ALL IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. PAGE OF 9

25 23 24 2 22 2 8 20 9 26 20 29 28 27 3 30 DETAIL C Motor Mount Assy SK2259a Figure 6d 20

PARTS LIST Model No: ECOD-AT, ECODL-AT, ECOF-AT, ECOFL-AT SHIPBOARD ELECTRIC CONVECTION OVEN March 8, 203, Rev E Key Number Part Number Qty Per Description 8 2U-30200-6 MTR /3HP 460V//60HZ 2SP 480V 2U-30200-7 MTR /3HP208/240V PH 2SPD 208V 2U-30200-60 MTR /3HP380VPH50HZ2SP 380V 9 2C-208-0 4 SCRW CARRAGE PLT 5/6X.75 ALL 20 2C-20202-09 4 WSHR LOCK 3/8 STD SPLIT ALL 2 2C-2030-09 2 NUT HEX 0-24 PLTD ALL 22 Q9-GCCO-67 MOTOR SHIELD ALL 23 Q9-6002-37 MOTOR MOUNT PLATE ASSY ALL 24 2C-200-42 4 SCRW THD MS 0-24X2 PLTD ALL 25 2U-7500-05 BLOWER WHEEL ECCO/GCCO ALL 26 2C-200-3 2 SCRW RHD MS 6-32X/2 PLTD ALL 27 Q9-GCCO-66-2 SPACER - SAFETY STAT ALL 28 2T-3040-09 STAT FXD 500 DEG OPEN ALL 29 2C-2030-0 2 NUT HEX 6-32 PLTD ALL 30 2C-2030-06 4 NUT HEX 5/6-8 PLTD ALL 3 2C-20202-08 4 WSHR PLT 5/6 LOCK SPLIT ALL IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. PAGE OF 2

64 65 83 08 66 67 8 82 09 75 74 79 80 84 0 72 73 72 68 7 70 78 77 76 DETAIL B 0 02 03 04 86 87 85 DETAIL D Typical Door Stop Assy Figure 6e 88 89 05 99 90 06 07 97 96 92 9 93 94 95 SK226a 22

PARTS LIST March 8, 203, Rev E Model No: ECOD-AT, ECODL-AT, ECOF-AT, ECOFL-AT SHIPBOARD ELECTRIC CONVECTION OVEN Key Part Qty Number Number Per Description 64 2E-30705-0 CONTC 2-SPD MTR-COIL 240 ALL 65 2E-30700-03 CONTC 3POLE 40A208-240VAC ALL 66 2E-3400-04 XFRMR 480/240VAC 00VA ALL 67 2E-30500-09 TRM BLOCK 3 POLE SMALL 95 440V, ECOF-AT-480G, ECOFL-AT208M, 68 2E-3800-07 CB 2/0 AMP 2 POLE OLDER UNITS ONLY 68 2E-3800-0 4 CB 250V 50A POLE CRLNGSW ECOFL-AT208M 70 2E-3090-08 FUSE HLDR FOR SC FUSE ALL 7 2E-30900-0 FUSE 5AMP 300V (SC-5) ALL 72 2E-30303-06 2 SWT TOG ON-ON DPDT BLK ALL 73 2E-30303-6 SWT TOG ON-ON BLK MOM ALL 74 2T-30402-27 STAT ADJ 450 DEG 48 PILOT ALL 75 2J-3080-03 TIMER MECHANICAL 5 HOUR ALL 76 2E-30303-09 SWT PLATE HI/LOW ALL 77 2E-30303-0 SWT PLATE ON/OFF IND ALL 78 2E-30303-05 SWT PLATE ON/OFF ALL 79 & 80 Y9-7070-9 ASSY KNOB ASSY 450 F ALL 79 2R-70702-08 DIAL PLATE 450o STAT ALL 80 2R-70700-0 KNOB BLNK UNIVERSAL BLACK ALL 8 2R-7070-55 KNOB 5 HOUR TIMER ALL 82 2R-70702-37 DIAL PLATE, 5 HOUR TIMER ALL 83 Y9-360-0- PILOT LT 250V W/TIN CLIP ALL 84 2S-3603-04 LAMPS INC 250V 50W ALL 85 2C-2009-04 0 SCRW THD MS SS 0-32X3/8 ALL 08 2M-60306-3 LBL INFO STAT LABEL ECO, VENT ALL 09 2M-60306-4 LBL INFO STAT LABEL ECO, TIMER ALL 0 2M-60306-5 LBL INFO STAT LABEL ECO, TEMP ALL 2M-60306-45 LABEL ECO POWER, LIGHT, SPEED ALL 05 Q9-5030-52 DOOR STOP LH ARM & BRACKET ASSY 0 2C-20405-02 2 RVT SOLID 3/6X 5/8R/H ALL 02 Q9-5030-54-2 DOOR STOP WASHER ALL 03 2P-70203-0 2 BEARING STL #4 ROLLER ALL 04 Q9-5030-55 2 DOOR STOP PAD ALL 86 Q9-5030-54 DOOR STOP ARM L/H ALL 87 2C-20-02 2 SCRW HXHD CAP /4-20X3/4 ALL 88 Q9-5030-52 DOOR STOP LH ARM&BRACKET ALL 89 2C-20303-0 2 NUT HX SS /4-20 ALL 05 Q9-5030-90 DOOR STOP RH ARM & BRACKET ASSY 0 2C-20405-02 2 RVT SOLID 3/6X 5/8R/H ALL 02 Q9-5030-54-2 DOOR STOP WASHER ALL 03 2P-70203-0 2 BEARING STL #4 ROLLER ALL 04 Q9-5030-55 2 DOOR STOP PAD ALL 86 Q9-5030-92 DOOR STOP ARM R/H ALL 87 2C-20-02 2 SCRW HXHD CAP /4-20X3/4 ALL 88 Q9-5030-90 DOOR STOP RH ARM&BRACKET ALL 89 2C-20303-0 2 NUT HX SS /4-20 ALL 06 PS-5030-50 KIT, DOOR STOP ASSY LH 90 2C-2009-52 4 SCRW PAN HD MS SS M3X8MM ALL 9 PS-5030-W94 DOOR STOP SLIDE L.H. w/stop ALL 92 Q9-5030-5-3 4 BACKUP WASHER ALL 93 2A-2040-04 4 SPCER /8IDX3/60DX/6LG ALL 94 2C-2030-42 4 NUT HEX ACORN M3-A2 ALL 95 2C-20406-02 2 RVT 5/32X /4 FH 00o ALL 96 2P-500-23 2 SPRING DOOR STOP-ECO ALL 97 Q9-5030-5-4 2 DOOR STOP SPRING TUBE ALL 99 Q9-5030-5- DOOR STOP LATCH L.H. ALL 06 Q9-5030-88- DOOR STOP ASSY R/H 90 2C-2009-52 4 SCRW PAN HD MS SS M3X8MM ALL 9 PS-5030-W93 DOOR STOP SLIDE R/H w/stop ALL 92 Q9-5030-5-3 4 BACKUP WASHER ALL 93 2A-2040-04 4 SPCER /8IDX3/60DX/6LG ALL 94 2C-2030-42 4 NUT HEX ACORN M3-A2 ALL 95 2C-20406-02 2 RVT 5/32X /4 FH 00o ALL 96 2P-500-23 2 SPRING DOOR STOP-ECO ALL 97 Q9-5030-5-4 2 DOOR STOP SPRING TUBE ALL 99 Q9-5030-89- DOOR STOP LATCH R/H ALL 07 PS-5030-89- DOOR STOP LATCH R/H ALL PS-5030-50 DOOR STOP 23LATCH L/H ALL

STAR INTERNATIONAL HOLDINGS INC. COMPANY Star - Holman - Lang - Wells - Bloomfield - Toastmaster 0 Sunnen Drive, St. Louis, 24 MO 6343 U.S.A.