Project: ustomer: Engineer: Pump Manufacturer: Technical Data Submittal Documents Model GPW Full Service Reduced Wye-delta losed Electric Fire Pump ontroller ontents: Data Sheets Dimensional Data Wiring Schematics Field onnections Note: The drawings included in this package are for controllers covered under our standard offering. Actual AS BUILT drawings may differ from what is shown in this package. March 07
Model GPW Electric Fire Pump ontroller From normal incoming power through Disconnecting Means (IS/B)* 3L R4 R5 S(LB) S M(LB) M(LB) 3L3 3L 3L R3A R3A M M S M M T3 T T T5 T4 T6 M S S Across-the line starting 3L Line current % of full load 0 Locked rotor current Wye delta starting Transition current losed transition Full load current S RES RES RES 0 40 60 80 00 Percent of motor speed (%) Starting Method: Reduced Wye-delta closed Typical Applied at Start: 00% Inrush urrent: 33% of normal load current Starting Torque: 33% Motor Type: Wye-delta No. of ontactors: at 58%, at 33% of motor FL Min. ampacity of motor conductors: 6 at 5% x 58% of FL Standard, Listings, Approvals and ertifications Enclosure Built to NFPA 0 (latest edition) Underwriters Laboratory (UL) UL8 - Fire Pump ontrollers SA. No. 4 Industrial ontrol Equipment FM Global lass 3/33 New York ity Accepted for use in the ity of New York by the Department of Buildings Seismic ertification See page 6 for details Optional E Mark Various EN, IE & EE directives and standards Protection Rating Standard: NEMA (IP3) Optional NEMA NEMA 3 NEMA 3R NEMA 4 Accessories Bottom entry gland plate Lifting Lugs Keylock handle NEMA 4X-304 sst painted NEMA 4X-304 sst brushed finish NEMA 4X-36 sst painted NEMA 4X-36 sst brushed finish Paint Specifications Red RAL300 Powder coating Glossy textured finish IP54 IP55 IP65 IP66 *Please see Disconnecting Means details on page 3. March 07
Model GPW Electric Fire Pump ontroller Shortcircuit Withstand Rating 00V to 08V 60Hz 0V to 40V 60Hz 380V to 46V 50 Hz / 60Hz (kw) 440V to 480V 60Hz 575V to V 60Hz Standard 00kA Optional 50kA 5-50 (3.7-0) 5-00 (3.7-47) 5-300 (3.7-0) 5-450 (3.7-335) n/a Standard 50kA 00 (47) 50 (84) 350-450 (57-335) 500 (373) Optional 00kA n/a n/a n/a n/a 5-500 (3.7-373) Ambient Temperature Rating Standard: 5 to 40 / 4 F to 04 F Optional: 5 to 55 / 4 F to 3 F Surge Suppression Disconnecting Means Service Entrance Rating Surge arrestor rated to suppress surges above line voltage Isolating switch and circuit breaker assembly: - Door interlocked in the ON position - Isolating switch rated not less than 5% of motor full load current - ircuit breaker continuous rating not less than 5% of motor full load current - Overcurrent sensing non-thermal type, magnetic only - Instantaneous trip setting of not more than 0 times the motor full load current ommon flange mounted operating handle Suitable as service entrance equipment Emergency Start Handle Flange mounted Pull and latch activation Integrated limit switch Across the line start (direct on line) Locked Rotor Protector Operate shunt trip to open circuit breaker Factory set at % of motor full load current Trip between 8 and 0 seconds Electrical Readings Pressure Readings Pressure and Event recorder Pressure Sensing phase to phase (normal power) Amperage of each phase when motor is running ontinuous system pressure display ut-in and ut-out pressure settings Pressure readings with date stamp Event recording with date stamp Under regular maintained operation, events are stored in memory for the life of the controller. Data viewable on operator interface display screen Downloadable by USB port to external memory device Pressure transducer and run test solenoid valve assembly for fresh water application Pressure sensing line connection / Female NPT Drain connection 3/8 Rated for 0-500PSI working pressure (standard display at 0-300PSI) Externally mounted with protective cover March 07 3
Model GPW Electric Fire Pump ontroller Audible Alarm Visual Indications 4 alarm bell - 85 db at 0ft. (3m) Power available Motor run Periodic test Manual start Deluge valve start Remote automatic start Remote manual start Emergency start Pump on demand/automatic start Low discharge pressure Pump room temperature (ºF or º) Lockout Visual & Audible Alarms Visual only Pump room alarm Pump on demand Motor trouble Power Loss Phase reversal Phase unbalance Phase loss L Phase loss L Phase loss L3 Low pump room temperature Weekly Test cut-in not reached ontrol voltage not healthy Overcurrent Undercurrent Undervoltage Overvoltage Invalid ut-in Service required Visual and Audible Locked rotor current Fail to start Low water level Low suction pressure Remote Alarm ontacts DPDT-8A-50V.A Power available Phase reversal Motor run ommon pump room alarm (field re-assignable)** Overvoltage Undervoltage Phase unbalance Low pump room temperature High Pump room temperature ommon motor trouble (field re-assignable)** Overcurrent Fail to start Undercurrent Ground fault Free (field programmable)** **Tornatech reserves the right to use any of these three alarm points for special specific application requirements. March 07 4
Model GPW Electric Fire Pump ontroller ViZiTouch V Operator Interface ommunication Protocol apability Operation Embedded microcomputer with software PL logic 7.0 color touch screen (HMI technology) Upgradable software Multi-language Protocol: Modbus onnection type: Shielded female connector RJ45 Frame Format: TP/IP Addresses: See bulletin MOD-GPx Start on pressure drop Automatic Start Remote start signal from automatic device Start pushbutton Run test pushbutton Manual Start Deluge valve start Remote start from manual device Manual with Stop pushbutton Stopping Automatic after expiration of minimum run timer *** Timers Actuation Mode Field Adjustable & Visual ountdown Visual Indication Minimum run timer ***(off delay) Sequential start timer (on delay) Periodic test timer Pressure Non-pressure Automatic Non-automatic ***an only be used if approved by the AHJ March 07 5
Model GPW Electric Fire Pump ontroller Seismic ertification Seismic ertification ompany Mounting details Seismic Information TRU ompliance, LL A Tobalski Watkins Affiliate TWEI Project No.: 504 Rigid base and wall mounting Building ode IB 05, B 06 Test riteria I- ES A56 Seismic Parameters SDS z/h I P A FLX-H A RIG-H A FLX-V A RIG-V ASE 7-0 hapter 3.0.0.5 3.0.40.33 0.53 3. 0.0.5 3.0.8.3 0.85 0.0 RRS for Nonstructural omponents Testing Spectral Response Acceleration (g).0 0. 0..0 0.0 Frequency, f (Hz) Horiz. Level Vert. Level Notes: omponents are tested in accordance with I-ES A56, IB 05 & B 06. OSD Special Seismic ertification Preapproval (OSP) March 07 6
Model GPW Electric Fire Pump ontroller A4 A8 Flow switch provision Foam pump application w/o pressure transducer and run test solenoid valve. 8 9 High water reservoir level c/w visual indication and alarm contact (DPDT) Emergency start alarm contact (DPDT) A9 Low zone pump control function 0 Manual start alarm contact (DPDT) A0 Middle zone pump control function Deluge valve start alarm contact (DPDT) A A3 A6 B BB B9A B9B B 4 6 7 0 4 5 6 7 High zone pump control function Non-pressure actuated controller w/o pressure transducer and run test solenoid valve Lockout/interlock circuit from equipment installed inside the pump room Built in alarm panel (0V.A supervisory power) providing indication for: Audible alarm & silence pushbutton for motor run, phase reversal, loss of phase. Pilot lights for loss of phase & supervisory power available Built in alarm panel same as B but 0-40VA supervisory power High motor temperature c/w thermoster relay and alarm contacts (DPDT) High motor temperature c/w PT00 relay and alarm contacts (DPDT) Ground fault alarm detection c/w visual indication and alarm contact (DPDT) Extra motor run alarm contact (DPDT) Periodic test alarm contact (DPDT) Low discharge pressure alarm contact (DPDT) Low pump room temperature alarm contact (DPDT) Low water reservoir level alarm contact (DPDT) High electric motor temperature alarm contact (DPDT) High electric motor vibration c/w visual indication and alarm contact (DPDT) Pump on demand / automatic start alarm contact (DPDT) Pump fail to start alarm contact (DPDT) ontrol voltage healthy alarm contact (DPDT) Flow meter valve loop open c/w visual indication and alarm contact (DPDT) 3 4 5 x D DA D5 D5D D0 D3 D4 D4A D4B D5 D8 D6 D7 Remote automatic start alarm contact (DPDT) Remote manual start alarm contact (DPDT) High pump room temperature alarm contact (DPDT) Second set of standard alarm contacts (DPDT) (Typical for city of Los Angeles and Denver) Additional visual and alarm contact (Specify function) (DPDT) Low suction pressure transducer for fresh water rated at 0-300PSI with visual indication and alarm contact Low suction pressure transducer for sea water rated at 0-300PSI with visual indication and alarm contact Pressure transducer and run test solenoid valve for fresh water rated for 0-500PSI (for factory calibration purposes only) Pressure transducer and run test solenoid valve for sea water rated for 0-500PSI Omit mounting feet (when applicable) High withstand rating for (normal power section) 08V to 480V = 50kA Anti-condensation heater & thermostat Anti-condensation heater & humidistat V = 00kA Anti-condensation heater & thermostat & humidistat Tropicalization E Mark with factory certificate Modbus with RTU frame format and RS485 connection Motor heater connection (external single phase power source and heater on/off contact) Note: Options chosen from this page are not electrically represented on the wiring schematics in this submittal package. March 07 7
Model GPW Electric Fire Pump ontroller D7A Motor heater connection (internal single phase power source and heater on/off contact) L0 L0 Other language and English (bilingual) French D8 D34A D36 D36A ustomized drawing set Field programmable I/O board - 5 Input / 5 output Redundant pressure transducer for fresh water rated for 0-500PSI Redundant pressure transducer for sea water rated for 0-500PSI L03 L04 L05 L06 L07 L08 Spanish German Italian Polish Romanian Hungarian L09 Slovak L0 roatian L zech L Portuguese L3 Dutch L4 Russian L5 Turkish L6 Swedish L7 Bulgarian L8 Thai L9 Indonesian L0 Slovenian L Danish L Greek L3 Arabic L4 Hebrew L5 hinese Additional Options: Note: Options chosen from this page are not electrically represented on the wiring schematics in this submittal package. March 07 8
Model GPW Electric Fire Pump ontroller ViZiTouch V Operator Interface PMS 95 PMS 36 Noir Home 3 5 6 7 8 4 - olor touch screen - Onscreen menu HOME page ALARM page ONFIGURATION page HISTORY page SERVIE page MANUAL page LANGUAGES page 3 - Screen protector 4 - Power LED (3 colors) 5 - START button 6 - STOP button 7 - RUN TEST button 8 - USB port March 07 9
Electric Fire Pump ontroller Model:GPR/GPS/GPW Dimensions Built to the latest edition of the NFPA 0 standard /" [] Ø7/8" [Ø3] X 5 7/8" [403] " [305] 9 3/8" [745] 8 3/8" [7] 6" [660] 4 /" [6] Ø3/8" [Ø0] X4 36" [94] See Notes 37 /4" [946] 38 /4" [97] 30" [763] " [305] 3 /4" [83] 7" [78] 5" [7] 5" [7] Sensing Line onnection - / " F.NPT Drain - 3/8 " M.TUBE 3 5/8" [] 7" [78] Ø/" [Ø3] X3 8 5/8" [8] 7" [79] 7" [78] Normal Power and Motor Leads Entrance 6" [5] / Power Table Min Max /4" [3] /" [64] 3" [76] " [5] 3" [76] 4" [0] opyright 06 08 5 30 0-40 5 30 380-400 - 45 5 60 440-480 5 60 5 75 Notes: Drawing for information only. Manufacturer reserves the right to modify this drawing without notice. ontact manufacturer for "As Built" drawing. - Standard NEMA: NEMA - Standard paint : textured red RAL 300. - All dimensions are in inches [millimeters]. - enter of ViZiTouch screen: 9-5/8" [75] from bottom (no feet). - Bottom conduit entrance through removable gland plate recommended. - Use watertight conduit and connector only. - Protect equipment against drilling chips. - Door swing equal to door width. - Seismic mounting to be rigid wall and base only. NY Dpt of Building Approved REV. DESRIPTION DD/MM/YY 0. First issue 6//6 DL Drawing number GPX-DI7 /E Tornatech Inc. All right reserved. This drawing and the information contained or depicted herein are the sole property of Tornatech Inc. opies are communicated to the recipient in strict confidence and may not be retransmitted, published, reproduced, copied or used in any manner, including as the basis for the manufacture or sale of any products, without the express prior written consent of Tornatech Inc. Projection
Electric Fire Pump ontroller Reduced / Wye-Delta (losed Transition) Model: GPW Wiring schematic Built to the latest edition of the NFPA 0 standard IS SA L3 L L B ST 4 Motor Run N N J40 TB J4 3L + AI4 R4 - R5 S(LB) 7 3L3 3L 3L S 8 0 M(LB) 4 M(LB) 3 R3A 8 R3A 9 M M S S 3L 3L3 3L 3L To J-J3-J4 T Black White T Black White T3 Black White 64 65 66 67 68 69 To J76 M** S M** Power Available Phase Reversal Pump Room Alarm Motor Trouble N N N N N N N N J4 TB J37 TB3 J39 TB4 J4 TB5 J5 J6 J7 J54 + AI3 - + AI - + AI - LS Red White Black LS- LS- LS ** PT S RES RES RES (Field Programmable) Remote Manual Start Lockout N IN IN N J55 TB6 J46 J43 J0 J8 DOWN AB SV UP Black Red SV- SV- Brown Blue - + AB SV VMB Remote Automatic Start Deluge Valve J* J* IN3 IN4 J5 J45 ST 4 I/O Water Reservoir Low IN5 IN6 IN7 J44 J47 4V in 4V out 4VA 3 X 4VA X XTR H H 3L 3L IN8 J36 R4 J38 R5 N N R4- R4- R5- R5- LS** R5 R4 LS- R3A * Remove jumper to use this feature ** ontact closes when emergency start is in "ON" position opyright 07 EB J76 L J53 J4 J3 J GF L3 L L3 L L 69 68 67 66 65 64 3L3 3L 3L NY Dpt of Building Approved To T-T-T3 To 3L-3L-3L3 REV. DESRIPTION DD/MM/YY Removed (fail safe) text from Power Available relay 0/0/7 0 First issue 0//6 Drawing for information only. Manufacturer reserves the right to modify this drawing without notice. ontact manufacturer for "As Built" drawing. Drawing number GPW-WS /E Tornatech Inc. All right reserved. This drawing and the information contained or depicted herein are the sole property of Tornatech Inc. opies are communicated to the recipient in strict confidence and may not be retransmitted, published, reproduced, copied or used in any manner, including as the basis for the manufacture or sale of any products, without the express prior written consent of Tornatech Inc. DL Legend M-M ontactors S-S AB B R T EB IS J LS PT RES SA ST SV VMB XTR ontactors Alarm Bell ircuit Breaker ontrol Relay urrent Transformer Electric I/O Board Isolating Switch Jumper Limit Switch Pressure Transducer Primary Resistor Surge Arrester Shunt Trip Solenoid Valve ViZiTouch Main Board Transformer
Electric Fire Pump ontroller Model: GPX Terminal Diagram and Sizing for Isolating Switch Power Terminals Bonding Ground 3 Phases Incoming Power Built to the latest edition of the NFPA 0 standard Notes: - For proper wire sizing, refer to NFPA70 and NE (USA) or E (anada) or local code. - ontroller suitable for service entrance in USA. 3 - For more accurate motor connections refer to motor manufacturer or motor nameplate. 4 - ontroller is phase sensitive. Incoming lines must be connected in AB sequence. L L L3 IS OPPER ONDUTORS for Isolating Switch (IS). Field Wiring According to Bending Space (AWG or MM). Terminals L - L - L3 Bending Space 5 " (7 mm) 8 " (03 mm) 5 7.5 0 5 0 5 30 40 50 60 08 x (8 to /0) x (8 to /0) x (3 to /0) x ( to /0) x (/0 to 50) x (3/0 to 50) x (4/0 to 50) 0 to 40 x (8 to /0) x (3 to /0) x ( to 50) x (/0 to 50) x (3/0 to 50) 380 to 46 x (8 to /0) x (8 to /0) x (3 to /0) x (3 to /0) x (8 to /0) x (8 to /0) x (3 to /0) x (8 to /0) x (8 to /0) Bending Space " (305 mm) 6 " (406 mm) 75 00 5 50 00 50 300 350 400 450 500 08 x (300 to 500) x (500) x (4/0 to 500) x (50 to 500) x (400 to ) 0 to 40 x (50 to 500) x (350 to 500) x (3/0 to 500) x (4/0 to 500) x (350 to 500) x (500 to ) 380 to 46 x (/0 to 50) x (3/0 to 50) x (50) x (300 to 500) x (3/0 to 50) x (4/0 to 500) x (300 to 500) x (400 to ) x (400 to 500) x (500 to ) x () x ( to 50) x (/0 to 50) x (3/0 to 50) x (4/0 to 50) x (350 to 500) x (3/0 to 50) x (4/0 to 500) x (300 to 500) x (350 to 500) x (400 to ) x (500 to ) x (3 to /0) x ( to 50) x (/0 to 50) x (3/0 to 50) x (50 to 500) x (350 to 500) x (3/0 to 50) x (4/0 to 500) x (50 to 500) x (300 to 500) x (350 to 500) Bending Space 5 " (7 mm) 8 " (03 mm) " (305 mm) ALUMINUM ONDUTORS for Isolating Switch (IS). Field Wiring According to Bending Space (AWG or MM). Terminals L - L - L3 Bending Space 5 " (7 mm) 8 " (03 mm) 0 " (54 mm) 5 7.5 0 5 0 5 08 x (3 to /0) x ( to /0) 0 to 40 x (8 to /0) x (3 to /0) x ( to /0) 30 40 50 60 x (/0) x (3/0 to 50) x (4/0 to 50) x ( to /0) x (/0 to 50) x (4/0 to 50) x (300) ** or x (50) 90 * x (50) 380 to 46 x ( to /0) x ( to /0) x (/0) x (8 to /0) x ( to /0) x ( to /0) x (8 to /0) x ( to /0) Bending Space " (305 mm) 6 " (406 mm) 08 0 to 40 380 to 46 Bending Space 75 00 5 50 00 50 300 350 400 450 500 x (400 to 500) x (350 to 500) x (3/0 to 50) x (/0 to 50) x ( to /0) x(500) 90 or x(4/0 to 50) ** x (500) x (50) x (3/0 to 50) x (/0 to 50) x (300 to 500) x (50 to 500) x (350) ** N/A ** x (50) x (3/0 to 50) x (350 to 500) x (300 to 500) x (400 to 500) x (300) ** or x (50) 90 * x (4/0 to 50) x () x (500) x (4/0 to 50) x (500) x (350 to 500) x () 90 * x (300 to 500) x (50) x (500) x (300 to 500) x (4/0 to 50) 5 " (7 mm) 8 " (03 mm) " (305 mm) x (400 to 500) x (300 to 500) x (500) x (350 to 500) x (500 to ) x (400 to 500) x () 90 * x () 90 * x (500) x (400 to 500) x () x () 90 * x (500) * For standard enclosure, use 90 aluminium wire. onsult Factory for Use of onductors Rated Lower than 90. ** onsult Factory NY Dpt of Building Approved REV. DESRIPTION Drawing for information only. Manufacturer reserves the right to modify this drawing without notice. ontact manufacturer for "As Built" drawing. DD/MM/YY General Revision (added AL coverage) 0/07/7 Drawing number GPX-TD60 / /E 0 First issue 6/03/7 DL opyright 07 Tornatech Inc. All right reserved. This drawing and the information contained or depicted herein are the sole property of Tornatech Inc. opies are communicated to the recipient in strict confidence and may not be retransmitted, published, reproduced, copied or used in any manner, including as the basis for the manufacture or sale of any products, without the express prior written consent of Tornatech Inc.
Electric Fire Pump ontroller Model: GPX Terminal Diagram and Sizing For GPP,GPY & GPW Built to the latest edition of the NFPA 0 standard M Motor Terminals M M M Notes: - For proper wire sizing, refer to NFPA70 and NE (USA) or E (anada) or local code. - ontroller suitable for service entrance in USA. 3 - For more accurate motor connections refer to motor manufacturer or motor nameplate. 4 - ontroller is phase sensitive. Incoming lines must be connected in AB sequence. T7 T8 T9 T T T3 T6 T4 T5 T T T3 M Model : GPP M Models : GPW & GPY OPPER ONDUTORS for Motor onnection (M-M). Field Wiring According to Bending Space (AWG or MM). Terminals T-T-T3-T4-T5-T6-T7-T8-T9 5 7.5 0 5 0 5 30 40 50 60 08 x (4 to 0) x (6 to ) x (4 to /0) x ( to 3/0) x ( to /0) 0 to 40 x (4 to 0) x (6 to ) x (4 to /0) x (3 to /0) x ( to /0) 380 to 46 x (4 to 0) x (4 to 0) x (4 to 0) x (6 to ) x (6 to ) x (4 to 0) x (4 to 0) x (4 to 0) x (0 to ) x (6 to ) x (6 to ) x (4 to 0) x (4 to 0) x (4 to 0) x (4 to 0) x (0 to ) 08 75 00 5 50 00 50 300 350 400 450 500 x (/0 to 3/0) x (3/0) x (50 to 300) x (/0 to 300) x (3/0 to 350) 0 to 40 x (/0 to /0) x (3/0) x (4/0 to 300) x (300) x (/0 to 300) x (4/0 to 350) 380 to 46 x (4 to /0) x ( to /0) x (/0 to /0) x (/0 to 3/0) x (4/0 to 300) x (300) x (/0 to 300) x (3/0 to 300) x (4/0 to 350) x (4/0 to 350) x (4 to /0) x (3 to /0) x ( to /0) x (/0 to 3/0) x (/0 to 3/0) x (4/0 to 300) x (300) x (/0 to 300) x (/0 to 300) x (3/0 to 350) x (4/0 to 350) x (6 to ) x (4 to /0) x (3 to /0) x ( to 3/0) x (/0 to 3/0) x (/0 to 3/0) x (4/0 to 300) x (50 to 300) x (300) x (/0 to 300) x (/0 to 300) ALUMINUM ONDUTORS for ontactor (M-M). Field Wiring According to Bending Space (AWG or MM). Terminals T-T-T3-T4-T5-T6-T7-T8-T9 5 7.5 0 5 0 5 30 40 50 60 08 x (6 to ) x (4 to ) x ( to /0) x (/0 to 3/0) x (/0) 0 to 40 x (6 to ) x ( to /0) x ( to /0) x (/0 to /0) 380 to 46 x (6 to ) x (4 to ) x (3 to /0) x (6 to ) x (4 to ) x (6 to ) 08 75 00 5 50 00 50 300 350 400 450 500 x (3/0) onsult Factory x (300) 90 * x (3/0 to 300) x (50 to 350) 0 to 40 x (/0) 90 * onsult Factory x (300) x (300) 90 * x (4/0 to 300) x (300 to 350) 380 to 46 x ( to /0) x (/0 to /0) x (/0 to /0) x (3/0) 90 * x (300) x (300) 90 * x (4/0 to 300) x (50 to 300) x (300 to 350) x (300 to 350) x (3 to /0) x ( to /0) x (/0) 90 * x (/0 to 3/0) x (3/0) 90 * x (300) x (300) 90 * x (3/0 to 300) x (4/0 to 300) x (50 to 350) x (300 to 350) x (4 to ) x (3 to /0) x ( to /0) x (/0 to 3/0) x (3/0) x (3/0) 90 * x (300) x (300) 90 * onsult Factory x (3/0 to 300) x (4/0 to 300) opyright 07 * For standard enclosure, use 90 aluminium wire. onsult Factory for Use of onductors Rated Lower than 90. NY Dpt of Building Approved REV. DESRIPTION Drawing for information only. Manufacturer reserves the right to modify this drawing without notice. ontact manufacturer for "As Built" drawing. DD/MM/YY General Revision (added AL coverage) 0/07/7 First issue 6/03/7 Drawing number GPX-TD60 / /E 0 DL Tornatech Inc. All right reserved. This drawing and the information contained or depicted herein are the sole property of Tornatech Inc. opies are communicated to the recipient in strict confidence and may not be retransmitted, published, reproduced, copied or used in any manner, including as the basis for the manufacture or sale of any products, without the express prior written consent of Tornatech Inc.
Electric Fire Pump ontroller Model: GPX Terminal Diagram and Sizing ontrol Terminals (EB) Terminals Wire Size: 4 - AWG 0.5 Nm Built to the latest edition of the NFPA 0 standard Remote Alarm Terminals (EB) Terminals Wire Size: 4 - AWG 0.5 Nm Remote Manual Start lose to start pump IN J5 Motor Run loses to alarm loses to alarm N N J40 TB Lockout lose to block start IN J5 Power Available loses to alarm loses to alarm N N J4 TB Remote Automatic Start Open to start pump J* IN3 J5 Phase Reversal loses to alarm loses to alarm N N J37 TB3 Deluge Valve Open to start pump J* IN4 J5 Pump Room Alarm ** loses to alarm loses to alarm N N J39 TB4 Alarm Inputs (EB) Terminals Wire Size: 4 - AWG 0.5 Nm Motor Trouble ** loses to alarm loses to alarm N N J4 TB5 Water Reservoir Low lose to signal alarm IN5 J5 (Field Programmable ***) loses to alarm loses to alarm N N J55 TB6 Network onnection (VMB) Shielded Female onnector RJ45 Modbus TP/IP I/O * Remove jumper to use this feature ** Re-assignable *** Not available on GPS models opyright 07 NY Dpt of Building Approved REV. DESRIPTION DD/MM/YY General Revision (added AL coverage) 0/07/7 0 First issue 6/03/7 Drawing for information only. Manufacturer reserves the right to modify this drawing without notice. ontact manufacturer for "As Built" drawing. Drawing number GPX-TD603 /E Tornatech Inc. All right reserved. This drawing and the information contained or depicted herein are the sole property of Tornatech Inc. opies are communicated to the recipient in strict confidence and may not be retransmitted, published, reproduced, copied or used in any manner, including as the basis for the manufacture or sale of any products, without the express prior written consent of Tornatech Inc. DL