LOBAY The Lobay luminaire combines the efficiency of HID light sources with special lens optics to create an enclosed luminaire that produces a wide variety of lighting distributions. This makes Lobay luminaires an excellent choice for both installation and operating economy, not to mention exceptional uniformity at low to medium mounting heights. HL-1051 8/02
LOBAY Choice of factory set distributions Die cast aluminum housing Thermally set white polyester powder paint Optional wet location listing CUL/US listed The Lobay luminaire achieves a wide square distribution by utilizing a unique optical assembly. It consists of an aluminum reflector with white baked-on enamel applied to the interior and exterior surface. This contour and paint treatment has been precision engineered to provide, with the proper lens, spacing criteria of 1.3 and 1.4. The square distribution is achieved by the Quadrature lens. This unique lens is injection molded with the visual appearance of four separate quadrants joined at the center. This lens design provides a wide square distribution with excellent horizontal and vertical illumination. The Refractive Grid lens is injection molded with a precisely formed array of hemispherical refractive elements on both the upper and lower sides of the lens. These optical elements freely transmit the downward light while intercepting potential glare and redirects it to useful light for the work area. Where excessive moisture is prevalent, a special 2
ASSEMBLY AREAS INSPECTION AREAS PRODUCTION AREAS WAREHOUSES PAPER MILLS EXPOSITION HALLS SUPER MARKETS HYPER-MARTS version of the Lobay luminaire which is UL listed as suitable for wet locations is available as an option. It is not recommended for use where high pressure water spray is used. The Lobay luminaire is UL listed to U.S. and Canadian safety standards. Ease of maintenance Relamping Simply unlatch the door and allow it to hinge downward, or lift off and remove as desired. After the lamp has been changed, merely swing the door up and latch. Cleaning Wipe the inner surface of the reflector and the tempered glass heat shield with a soft cloth. Enclosed optical assem- bly The standard fixture optical assembly is enclosed. The lens is gasketed in the door frame with another gasket between the optics and the die cast housing, resulting in a fixture with low dirt depreciation. Ease of installation The ballast assembly installs quickly with the pendant mounting plate which threads onto.75 NPT conduit and easily slides into the ballast key way. The optional quick disconnect box or thru-way wiring box can be ceiling mounted or threaded onto.75 NPT conduit. The reflector attaches securely with three hex head slotted screws on to the gasketed die cast mounting adapter on the ballast assembly. The integral hinge design allows for easy attachment of the optical door assembly. LOBAY 3
LOBAY RESEARCH & DEELOPMENT CENTER 800 CD/DI 0.0 5078 5.0 5111 487 10.0 5032 15.0 4989 1404 20.0 4766 25.0 4641 2118 30.0 4492 35.0 4313 2667 40.0 4109 45.0 3850 3115 50.0 3138 55.0 2206 2472 60.0 1627 65.0 1222 1445 70.0 865 75.0 546 658 80.0 295 85.0 100 127 90.0 0 RESEARCH & DEELOPMENT CENTER 1000 CD/DI 0.0 6232 5.0 6304 602 10.0 6174 15.0 6362 1803 20.0 6041 25.0 5937 2748 30.0 5826 35.0 5925 3722 40.0 5213 45.0 3872 2999 50.0 2508 55.0 1658 1488 60.0 990 65.0 606 602 70.0 382 75.0 284 300 80.0 218 85.0 121 132 90.0 11 RESEARCH & DEELOPMENT CENTER 1400 CD/DI 0.0 8867 5.0 8920 850 10.0 8730 15.0 8625 2437 20.0 8278 25.0 8064 3698 30.0 7866 35.0 7617 4706 40.0 7362 45.0 6660 5502 50.0 5536 55.0 3744 4344 60.0 2827 65.0 2128 2440 70.0 1497 75.0 953 1149 80.0 510 85.0 178 227 90.0 2 21000 E-28 25 FT. 1.3 0-30 400919.1 30-60 8253 39.3 60-90 2231 10.6 0-90 14493 69.0 21000 E-28 25 FT. 1.4 0-30 5153 24.5 30-60 8208 39.1 60-90 1034 4.9 0-90 14395 68.5 36000 BT-37 25 FT. 1.3 0-30 6985 19.4 30-60 14551 40.4 60-90 3815 10.6 0-90 25352 70.4 46957 46854 46956 ρ ρ ρ.80.80.80.73.73.73.69.71.69.66.65.64.62.59.62.58.55.58.55.52.50.55.50.46.51.48.44.42.49.43.39.46.42.38.36.44.38.34.41.37.33.31.39.34.30.37.32.29.27.36.30.26.34.29.26.24.33.27.23.31.26.23.21.30.24.21.28.24.21.19.28.22.19.26.22.19.17 ρ ρ ρ.79.79.79.72.72.72.68.71.69.67.66.64.63.60.64.61.58.60.57.55.53.58.53.50.54.51.48.46.52.47.44.49.45.42.41.47.42.38.45.41.38.36.43.38.34.41.37.34.32.39.34.30.37.33.30.29.36.31.27.34.30.27.26.33.28.25.32.28.25.23.31.26.23.29.25.22.21 ρ ρ ρ.82.82.82.75.75.75.70.73.70.68.67.65.64.60.64.60.56.59.56.54.51.56.51.47.52.49.45.43.50.44.40.47.42.39.37.45.39.35.42.37.34.32.40.34.30.38.33.30.28.36.31.27.34.30.26.25.33.28.24.31.27.23.22.30.25.21.29.24.21.20.28.23.19.27.22.19.18 RESEARCH & DEELOPMENT CENTER 1800 CD/DI 0.0 10157 5.0 10086 963 10.0 9875 15.0 9917 2811 20.0 9753 25.0 9723 4500 30.0 9681 35.0 9918 6231 40.0 8662 45.0 6334 4905 50.0 4146 55.0 2762 2478 60.0 1653 65.0 10091001 70.0 631 75.0 465 492 80.0 350 85.0 200 219 90.0 9 RESEARCH & DEELOPMENT CENTER 1800 CD/DI 0.0 11758 5.0 11876 1133 10.0 11650 15.0 11647 3285 20.0 11174 25.0 10953 5012 30.0 10643 35.0 10384 6513 40.0 9842 45.0 8955 7361 50.0 7612 55.0 5652 6235 60.0 3940 65.0 2961 3567 70.0 2080 75.0 1315 1610 80.0 715 85.0 250 319 90.0 7 RESEARCH & DEELOPMENT CENTER 2000 CD/DI 0.0 13340 5.0 13313 1271 10.0 13122 15.0 13367 3789 20.0 13115 25.0 13178 6100 30.0 13326 35.0 13091 8224 40.0 12048 45.0 88796876 50.0 5702 55.0 3808 3416 60.0 2250 65.0 13691359 70.0 859 75.0 647 684 80.0 485 85.0 270 295 90.0 4 36000 BT-37 25 FT. 1.4 0-30 8274 23.0 30-60 13614 37.8 60-90 1712 4.8 0-90 23600 65.6 50000 ET-18 25 FT. 1.4 0-30 9431 18.9 30-60 2010940.2 60-90 5496 11.0 0-90 35036 70.1 50000 ET-18 25 FT. 1.4 0-30 1115922.3 30-60 18516 37.0 60-90 2339 4.7 0-90 32015 64.0 46791 46967 46864 ρ ρ ρ.76.76.76.69.69.69.65.69.66.65.63.62.61.58.62.58.55.57.55.53.50.55.51.48.52.49.46.44.50.45.42.47.43.41.39.45.40.37.43.39.36.34.41.36.33.39.35.32.31.38.33.29.36.32.29.27.34.30.26.33.29.26.25.32.27.24.30.26.24.22.29.25.22.28.24.21.20 ρ ρ ρ.81.81.81.75.75.75.70.72.70.67.66.65.63.60.63.59.56.59.56.53.50.56.51.47.52.48.45.43.49.44.40.46.42.38.36.44.38.34.41.37.33.31.40.34.30.37.33.29.27.36.30.26.34.29.26.24.33.27.23.31.26.23.21.30.25.21.28.24.21.19.28.22.19.26.22.19.17 ρ ρ ρ.74.74.74.68.68.68.64.67.65.63.62.61.60.57.60.57.54.56.54.52.49.54.50.47.51.48.45.43.49.44.41.46.43.40.38.44.40.36.42.38.35.34.40.35.32.38.34.31.30.37.32.28.35.31.28.27.34.29.26.32.28.25.24.31.26.23.30.26.23.22.29.24.21.27.24.21.20 Photometrics 4
Performance Specification Complete luminaire shall be Holophane catalog number. The luminaire shall consist of two sub-assemblies: ballast assembly, containing the electrical components, mounting hardware, and reflector attachment lugs; and the optical assembly. The complete luminaire shall be UL listed to U.S. and Canadian safety standards as suitable for use in damp locations and ambients of up to 40 C as standard. Ballast assembly The die cast aluminum housing shall be protected against corrosion by a seven stage pretreatment followed by electrostatically applied white polyester powder paint, cured and baked on at 218 C; this exceeds ASTM standards for hardness, humidity, impact and salt spray resistance to prevent cross hatch, fading, cracking, and other corrosion related deterioration. All hardware shall be zinc plated for corrosion protection. Optical assembly The optical assembly shall be an aluminum reflector with white baked on enamel on the outside and to the internal reflecting surface. The door will contain, in a frame, the Quadrature or Refractive Grid lens with a clear tempered glass roundel between the lamp and the lens. When the door is in place, hinged and latched, the optical assembly will be enclosed. When tested with a watt lamp, zonal outputs shall not be less than: Zonal Degrees 0-60 60-90 0-90 90-180 % Total Lamp Lumens Luminaire shall have a spacing criteria of. Optional mounting methods (choose one) P- Pendant The separable.75 NPT threaded conduit mounting plate with integral set screw shall provide quick install slide on attachment. Housing shall be balanced and suitable for support from hooks, loops or conduit. 1 2 3 4 5 6 A wireway cover shall enclose the wiring chamber which is suitable for 90 C supply wire. N- Non-disconnect pendant and through-way wiring The die cast aluminum pendant and throughway integral wiring box shall contain provisions for both.75 NPT conduit and direct ceiling mounting. It shall contain an integral hinge pin on the housing to support the luminaire while electrical connections are made. It shall have the same corrosion resistant finish as the housing. It shall have 2 cast in side knockouts, 4 ceiling drill points,.75 NPT conduit threaded top opening, and be UL listed for up to five #10 AWG conductors for through-way wiring. Q- Quick-disconnect pendant and through-way wiring The die cast aluminum pendant and/or through-way quick disconnect wiring box shall contain provisions for both.75 NPT conduit and direct ceiling mounting. It shall contain an integral hinge pin on the housing. It shall have the same corrosion resistant finish as the housing. It shall have 2 cast in side knockouts, 4 ceiling drill points,.75 NPT conduit threaded top opening, and be UL listed for up to five #10 AWG conductors for through-way wiring. The fixture housing shall swing up and connect to the Q box by latching the captive J bolt and wing nut without use of tools. A dead front receptacle shall be mounted inside the Q box which will make an electrical 1 connection with the prewired male plug on the fixture housing. The receptacle shall be UL listed and CSA certified for connection to the lighting branch circuits which can then be energized before the housing is attached. The grounding connection shall be the first to make contact and the last to disconnect. It shall be UL listed per UL-1059 (Panel Board Accessory) and UL-98 (Enclosed and Dead Front Switches) and CSA certified permitting the fixture to be disconnected while under load to meet OSHA requirements for relamping. The Lobay luminaire is covered by patents 4,285,034 and 1,140,095. The physical properties of the Holophane Lobay Series luminaires represent typical average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations. They are supplied as a technical service and are subject to change without notice. Check with your local Holophane sales representative to assure current information. Quick install slide on pendant mounting plate. Optional quick disconnect support for application flexibility and disconnect under load capability. 2 Die cast, aluminum ballast and optics support housing. Pretreated and coated with electrostatically applied, thermally set white polyester powder paint. 3 4 Closed top optical assembly. Optical assembly, interior and exterior painted white, and proper lens combine to provide distinct lighting distributions. 5 Hinged, and if desired, removable door frame permits easy relamping. 6 Quadrature lens (square distribution) and Refractive Grid lens (low brightness ) are engineered to meet a wide variety of lighting requirements. LOBAY 5
LOBAY How to construct a catalog number for Lobay Fixture type Example: LY 400HP 12 Q SQ10 F1 1 2 3 4 5 6 Cat. no. Description 1 Luminaire LY Lobay. Standard fixture color is white 2 Source and Wattage 400HP 400W HPS 40LHP 400W HPS, energy saving ballast 175MH 175W MH 175PM 175W, pulse start 250MH 250W MH and M 25LMH 250W MH and M, energy saving ballast 250PM 250W MH, pulse start 25LPM 250W MH, pulse start, energy saving ballast 320PM 320W MH, pulse start 350PM 350W MH, pulse start 35LPM 350W MH, pulse start, energy saving ballast 400MH 400W MH and M 40LMH 400W MH and M, energy saving ballast 400PM 400W MH, pulse start 40LPM 400W MH, pulse start, energy saving ballast 3 oltage 12 120 volt 20 208 volt 24 240 volt 27 277 volt 34 347 volt 48 480 volt MT Multi-voltage (120 208, 240, 277 in U.S.) T ari-tap (120, 277, 347 in Canada) 4 Mounting P Pendant mount Q Quick disconnect power hanger for pendant and thru-way wiring N No quick disconnect power hanger for pendant and thru-way wiring 5 Optics SQ10 Square Distribution 1.3-1.4 spacing criteria GD10 Refractive Grid 1.4 spacing criteria 6 Options and Accessories See pages 7 and 8 for available options and accessories P - 648mm (25.5 ) N/Q - 724mm (28.5 ) 660mm (26 ) Order number Job name 6 Ordering Data
Options 110mm (4.5 ) 120mm (4.88 ) DN20NPT (.75 ) threaded entry 22mm (.88 ) UPH-35 Power-hook 130mm (4.94 ) (2) wiring access covers 30mm (1.06 ) (2) KO s for DN20 (.75 ) conduit Thru-way UPH-35 Pendant UPH-36 PHCB HFW Catalog number Description Options (Factory installed) F1 Single fuse assembly for 120, 240, 277, 347 F2 Double fuse assembly for 208, 240, 480 CDP-L5-15-3 (120) 120 914mm (3 ), three conductor cord and NEMA plug (order PF also) CDP-L6-15-3 (208/240) 208/240 914mm (3 ), three conductor cord and NEMA plug (order PF also) CDP-L7-15-3 (277) 277 914mm (3 ), three conductor cord and NEMA plug (order PF also) CDP-L24-20-3 (347) 347 914mm (3 ), three conductor cord and NEMA plug (order PF also) CDP-L8-20-3 (480) 480 914mm (3 ), three conductor cord and NEMA plug (order PF also) X Cord length beyond 914mm (3 ) (X = no. of feet) AERS AERS Automatic Energy Reduction System. Select DC low voltage or AC line voltage control system. Handled through TSG. Control Module and sensors must be specified through TSG. 40 C rated. D35 35% low mode operation. (DC) Available with 400HP and 40LHP only D50 50% low mode operation. A35 35% low mode operation. (AC) N/A with CDP, PHCB, or Q. Available with 400HP and 40LHP only A50 50% low mode operation. (AC) N/A with CDP, PHCB, or Q EM Standby lighting fixture uses a D.C. bayonet base, tungsten halogen lamp to provide standby lighting ER Emergency lighting fixture less relay for use with a 120 volt external power source to operate a D.C. bayonet tungsten halogen lamp to provide emergency lighting. (all fixtures except CDP, PHCB, or Q ) Not CSA certified PS HPS protected starter PF-105 Loop,.75 NPT male; all fixtures except Q PF-121 Safety hook,.75 NPT male; all fixtures except Q PF-129 Anti-rotational hook,.75 NPT male; all fixtures except Q PF-291 Safety hook with gasketed strain relief cord connector,.75 NPT male. Not available with Q PHCB (120, 208, 240, Power-hook cord, special configuration plug cap and PF-105 loop attached 277, 347) Not available with MT, ER, Q. Not available with CSA certification PHCB-L8-480 (480) Power-hook cord, special configuration plug cap and PF-105 loop attached Not available with ER, Q. Not available with CSA certification W Wet location unit - Available with Pendant mount 40 C only. Available with EM and PS. NA with CDP, PHCB, F1, F2, or ER HFW Holoflex flexible wiring system CD-3 3 cord only. Available also in 4, 5 or 6 lengths. LOBAY 7
Accessories 57mm (2.25 ) 73mm (2.88 ) 45mm (1.75 ) 92mm (3.62 ) 67mm (2.63 ) 71mm (2.78 ) PF-105-B Loop.75 NPT male PF-121-A Safety hook,.75 NPT male PF-129-A Anti-rotational hook.75 NPT male PF-116-A Loop.75 NPT female PF-122-A Safety hook,.75 NPT female PF-291 Safety hook,.75 NPT male Catalog number Description Accessories (shipped separately) LAMP Appropriate HID lamp supplied with fixtures PF-105-B Loop,.75 NPT male; not available with Q PF-116-A Loop,.75 NPT female; not available with Q PF-121-A Safety hook,.75 NPT male: not available with Q PF-122-A Safety hook,.75 NPT female; not available with Q PF-129-A Anti-rotational hook,.75 NPT male: not available with Q PF-291 Safety hook with gasketed strain relief cord connector,.75 NPT male. Not available with Q UPH-35-XXX-WH (120, 208, Thru-way power-hook (order PHCB with fixture); not available with, Q or -ER. Insert voltage for XXX. 240, 277, 347) Not CSA certified UPH-35-L8-480-WH (480) Thru-way power-hook (order PHCB-L8-480 with fixture); not available with -ER or Q. Not CSA certified UPH-36-XXX-WH (120, 208, Pendant power-hook (order PHCB with fixture); not available with, -ER, Q. 240, 277, 347) Insert voltage for XXX. Not CSA certified UPH-36-L8-480-WH (480) Pendant power-hook (order PHCB-L8-480 with fixture); not available with -ER, Q Acuity Lighting Group, Inc. 214 Oakwood Ave., Newark, OH 43055 / Holophane Canada, Inc. 9040 Leslie Street, Suite 208, Richmond Hill, ON L4B 3M4 / Holophane Europe Limited, Bond Ave., Milton Keynes MK1 1JG, England / Holophane, S.A. de C.., Apartado Postal No. 986, Naucalpan de Juarez, 53000 Edo. de Mexico Contact your local Holophane factory sales representative for application assistance, and computer-aided design and cost studies. For information on other Holophane products and systems, call the Inside Sales Service Department at 740-345-9631. In Canada call 905-707- 5830 or fax 905-707-5695. Limited Warranty and Limitation of Liability Refer to the Holophane limited material warranty and limitation of liability on this product, which are published in the Terms and Conditions section of the current product digest, and is available from our local Holophane sales representative. isit our web site at www.holophane.com HL-1051 8/02 2002 Acuity Brands, Inc Printed in USA