Uniclass L48 EPIC D8 CI/ SfB (.5) X Orbis Commercial Range 2 4 architectural architectural ironmongery www.laidlaw.net architectural ironmongery doorset solutions handrail & balustrading access control
THE LAIDLAW SERVICE Laidlaw is the leading specifier, distributor and technical service provider of architectural hardware to the UK construction industry. Laidlaw is able to offer a wide range of architectural products that combine design and function across a broad band of product categories. This is achieved by working closely with manufacturing partners ensuring consistent quality and performance are achieved from the products offered and by keeping up to date with market requirements and technical specifications to ensure Laidlaw remains at the forefront of the markets it serves. In addition to the renowned Orbis brand the Laidlaw portfolio also incorporates specialist product areas such as Electronic Access Control and AntiLigature fittings. Laidlaw is also able to offer a comprehensive system of Orbis Timber Doorsets which are fully compatible with the Orbis range of architectural hardware. For further information on any of the Laidlaw products and services, please refer to the full range of product brochures or alternatively call one of the Laidlaw branches nationwide as listed on the back page of this brochure. Specification Advice Laidlaw's team of GAI trained consultants is available to assist with all of the detailed product enquiries associated with the increasingly complex subject of hardware specification. Whether it be advice on product compliance for Disability Discrimination Act (DDA) applications or test certification for fire door applications, your local Laidlaw Technical Consultant is always on hand to guide you to the most appropriate specification. Product Development Orbis products are subject to continual design and manufacturing development in order to improve performance or to meet the changing demands of standards, testing or other building legislation. Project Management Having provided guidance in the specification and selection of appropriate products, Laidlaw's scheduling team will produce fully detailed, door by door ironmongery schedules along with a full bill of materials. Laidlaw will then project manage the supply of product including the manufacture of special or bespoke items; supply of relevant installation drawings; and, where necessary, certification and delivery schedules. CPD seminars Laidlaw is a RIBA approved provider of CPD seminars and is able to offer specifiers seminars and workshops on a wide range of hardware related subjects including DDA, Doc M and BS 800 compliance. Packaging and Delivery Laidlaw will work alongside the customer's project management team to ensure the product arrives on site in the most appropriate form. This could include labelling to the architect's door numbers, or already installed on Orbis Timber Doors. Laidlaw will ensure deliveries are made in full and on time. www.laidlaw.net
ORBIS COMMERCIAL CONTENTS THE LAIDLAW SERVICE ORBIS COMMERCIAL INTRODUCTION 5 LEVER FURNITURE 6 8 PULL HANDLES 9 PUSH PLATES, KICKING PLATES & FIXINGS 2 OVERHEAD DOOR CLOSERS ELECTROMAGNETIC DOOR CLOSERS 4 FLOOR SPRINGS 5 6 FIRE DOOR CONTROLS 7 HINGES 8 MORTICE CYLINDER LOCKCASES 9 20 CYLINDERS & REBATE SETS 2 SIGNS & SYMBOLS 22 24 DOOR STOPS & HOLDERS 25 PULLS, HOOKS & WC FITTINGS 26 FLUSH & SLIDE BOLTS 27 PANIC EXIT HARDWARE 28 6 STANDARDS & BS EN CLASSIFICATIONS 7 8 DDA, APPROVED DOC. M & BS 800 9 4 INDEX 42 2 www.laidlaw.net
ORBIS COMMERCIAL INTRODUCTION Orbis Commercial A comprehensive and fully coordinated range of architectural hardware defined by a simple and timeless aesthetic. This visual clarity is combined with high quality performance which lends itself to a wide range of applications from contemporary commercial offices to public buildings. Quality of design, manufacture, finish and performance are provided in equal measure in Orbis Commercial, with most components available in Satin or Polished Stainless Steel or in a Silk Anodised Aluminium finish. www.laidlaw.net Front cover Orbis 54 80.9FRS lever on fixed rose and 5 800.25 lever turn escutcheon in Polished Stainless Steel This page Orbis 54 80.22FRS lever on fixed rose with 5 800. Euro profile cylinder escutcheon in Satin Stainless Steel
Within the Orbis Commercial range is a selection of lever and pull handle designs and an advanced system of door closers including many which will enable building owners to satisfy their obligations under the Disability Discrimination Act. ORBIS COMMERCIAL INTRODUCTION Orbis Commercial door furniture can be completely integrated with the Orbis Timber Doorset Range. Factory preparation for the hardware ensures perfect installation to maximise the high performance and aesthetics of the Orbis Commercial Range. Please refer to our Orbis Timber Doorsets brochure. a b c Coordination of design and finish is achieved across a full range of products ensuring integrated Orbis Commercial products can be specified for the full hardware requirement of most buildings. Each component in the Orbis Commercial range is designed for maximum performance. Products are tried and fully tested to the latest BS EN standards with full certification and CE marking where applicable. a. Orbis 7 80. radius corner hinge in Satin Stainless Steel b. Softline electromagnetic holdopen door closer in Satin Stainless Steel finish c. Orbis 5 822.45 bolt through pull handle used with deadlock 2 85 with Euro profile cylinder and 5 800. escutcheon 4 www.laidlaw.net
ORBIS COMMERCIAL INTRODUCTION BS EN Performance standards Many of the product types within the Orbis Commercial range have been developed specifically to meet or exceed the latest European Standards. Where different grades of compliance are applicable, this will be indicated in the description against each item. More detailed information on standards and BS EN Classifications can be found on page 7 & 8. CE Marking Where CE marking is permitted, items are marked with the CE icon. The CE classification is indicated against each item where this is appropriate. Further information on CE marking and classifications can be found on page 7. Fire Testing Fire testing is an ongoing process with Laidlaw. Many of the Orbis Commercial hardware items have been included on timber fire door tests up to 2 hours and on steel fire doors up to 4 hours. The icon indicates the item has been successfully included in fire tests and the brief details of these are included in the general descriptions. DDA, Approved Doc. M & BS 800 The principal of ensuring buildings are accessible to able and less able people alike is manifest in Approved Document M of the Building Regulations and with further guidance in BS 800 which contains specific dimensional information for certain items of architectural hardware. The disabled symbol is used throughout this document to identify those Orbis Commercial items which conform to the requirements of Approved Document M and are therefore appropriate for use in DDA applications. Further information can be found on pages 9 to 4. Materials & Orbis Commercial products are manufactured using only the highest grade materials including Grade 04 and Grade 6 stainless steel. The range is available in Satin Stainless Steel, Polished Stainless Steel and Silk Anodised Aluminium. Above 5 822.45BB pull handles in Polished Stainless Steel 5 www.laidlaw.net Ordering Products When ordering products from the catalogue remember to specify the finish code after the product code e.g 5 8.0BBPS7 In certain cases, an applied finish is used. These are carefully selected to match the main hardware finishes. Dimensions All dimensions shown throughout this brochure are in mm. The products listed within this publication are subject to a 0 year guarantee against defects proved to be the result of faulty manufacture or defective materials unless otherwise stated. Extended guarantees can be obtained for specific projects on application via your Laidlaw Technical Consultant and subject to an agreed maintenance programme. Satin Stainless Steel PS7 Polished Stainless Steel SA7 Silk Anodised Aluminium
ORBIS COMMERCIAL LEVER FURNITURE The essence of the Orbis Commercial range is a series of timeless round bar lever handles which are supplied prefixed to the rose mounting. These assemblies give specifiers and installers the benefits of: Simplified specification with complete lever and rose assemblies with spindle and fixings Easier and quicker installation Greater accuracy of installation Improved strength and durability Orbis Commercial lever handle assemblies have the following features All levers are circlip fixed to the rose inner Phosphor bronze bearing washers are captive in the assembly and provide extra durability as standard Improved point fixing Levers prefixed to rose Secure M4 bolt through rose fixings at 8mm centres Break through grub screw fixing into spindle Supplied with M4 bolt through fixings for back to back assembly and optional face fixing screws Snap on rose cover conceals fixings Fixing centres (8mm) compatible with all major lockcase ranges Spindles for specific applications are available (see page 8) Lever is circlip fixed to the rose inner M4 fixing bolts securely connect each rose through the lock case Pushon covers conceal all rose fixings Phosphor bronze bearing washer is concealed within the rose assembly Break through grub screw in each lever pierces the spindle to lock the 2 levers together 6 www.laidlaw.net
ORBIS COMMERCIAL LEVER FURNITURE Lever Handle Straight Round bar straight lever handles prefixed to 5mm concealed fixing roses 8mm spindle supplied & PS7 finishes are Grade 6 stainless steel Exceeds the requirements of BS EN 906 grade 4 (highest grade) Please note, all levers are supplied with "break through" type spindle for secure grub screw fixing. 60/65 52 5 4/6 Ø Item no. 54 800.9FRS 54 800.22FRS Diameter (mm) 9 22 PS7 SA7 Unit pair pair Specification advice When used with Orbis Commercial escape sashlock please specify suitable split follower spindles FPL. for doors 8 54mm thick FPL.2 for doors 55 65mm thick Lever Handle Return to door Round bar return to door lever handles prefixed to 5mm concealed fixing roses 8mm spindle supplied & PS7 finishes are Grade 6 stainless steel Exceeds the requirements of BS EN 906 grade 4 (highest grade) Complies with the dimensional requirements of BS800 60/65 52 5 Ø Item no. 54 80.9FRS 54 80.22FRS Diameter (mm) 9 22 PS7 SA7 Unit pair pair Specification advice For half set applications please specify suitable spindles from page 8 and 5 800.0 blank rose to allow use of bolt through fixings. 4/6 Lever Handle On insert rose Return to door lever handles are available prefixed to Orbis insert roses for use with the Orbis Premier flat backplate system. For further details please refer to our Orbis Premier brochure. 50 Item no. 54 80.9FRS9 54 80.22FRS9 Diameter (mm) 9 22 PS7 SA7 Unit pair pair 2 60/65 Ø 4/6 Lever Handle Return to door Elliptical section return to door lever handle prefixed to 5mm concealed fixing roses Suitable for use with all rose and plate mountings (see pages 79) 8mm spindle supplied Available in SA7 finish only Exceeds the requirements of BS EN 906 grade 4 (highest grade) Complies with the dimensional requirements of BS800 65 52 5 6 25 Item no. Diameter (mm) PS7 SA7 Unit 54 850.25FRS 8 x 25 pair Please note: FRS Suffix denotes levers are circlip fixed to Orbis Commercial Concealed roses. 7 www.laidlaw.net
Escutcheons Concealed fixing Suitable for use in conjunction with all Orbis Commercial rose mounted lever handles or with pull handles Snap on cover conceals fixings Thumbturns complete with 5mm spindle and 8mm adapter suitable for door thicknesses from 5 to 54mm Supplied with selftapping screws for face fixing ORBIS COMMERCIAL LEVER FURNITURE 5 800.0 5 800. 5 800.2 5 800. 5 800.4 5 800.5 5 800.5 5 800.25 Specification advice Extended bathroom turn 5 800.25 is recommended for special needs applications. 5 52 52 5 6 4 26 6 60.5 0 Item no. Function PS7 SA7 Unit 5 800.0 blank 5 800. 5 800.2 5 800. 5 800.4 5 800.5 5 800.5 lever key oval profile euro profile indicator/release standard turn large turn 5 800.25 extended turn Fixing Packs As standard all levers are supplied with FPL. 'Break Through' spindle and FPL. back to back fixings for doors 8mm to 54mm thick and face fixing screws. Alternative fixing packs are available for thicker doors, for sided applications or for use with locks which have a split follower function. Back to back fixing bolts Face fixing screws 05 (FPL.) 20 (FPL.2) 8 5 cut on site 8 FPL FPL2 Item no. FPL. FPL.2 FPL2. FPL2.2 Description 'Break Through' spindle Back to back fixings bolts and face fixing woodscrews 'Break Through' spindle Back to back fixings bolts and face fixing screws Swivel half spindle for sided lever operation and face fixing woodscrews Swivel half spindle for sided lever operation and face fixing woodscrews Door Thickness 8 54mm 55 65mm 8 54mm 55 65mm 05 (FPL.) 20 (FPL.2) 0 8 FPL FPL. FPL.2 Split spindle Back to back fixings bolts and face fixing woodscrews Split spindle Back to back fixings bolts and face fixing woodscrews 8 54mm 55 65mm FPL5.2 FPL5.2 Adapter to convert 5mm bathroom spindle to suit 8mm follower n/a 8 www.laidlaw.net
ORBIS COMMERCIAL PULL HANDLES Pull Handles Round Bar Section Designed to be compatible with all round bar lever handle designs Bolt through or back to back fixing options Choice of lengths available Choice of diameters available Standard M8 fixing packs suit doors up to 55mm thick other thicknesses to special order Alternative fixing types are also available (see page ) Please note, these pull handles are also interchangeable with the pull handles and backplate system in the Orbis Premier range. For further details refer to the Orbis Premier Range brochure. 9Ø 5 89.24 45 5 89.0 5 89.45 5 89.60 Bolt through fixing Item no. Diameter (mm) Centres (mm) PS7 SA7 Unit 5 89.5 9 50 5 89.8 9 80 5 89.24 9 240 5 89.0 9 00 5 89.45 9 450 5 89.60 9 600 Back to back fixing Diameter Centres Item no. (mm) (mm) PS7 SA7 Unit 5 89.5 BB 9 50 pair 5 89.8 BB 9 80 pair 5 89.24 BB 9 240 pair 5 89.0 BB 9 00 pair 5 89.45 BB 9 450 pair 5 89.60 BB 9 600 pair centres 5 822.24 5 822.0 5 822.45 5 822.45 Bolt through fixing Diameter Centres Item no. (mm) (mm) PS7 SA7 Unit 5 822.8 22 80 5 822.24 22 240 5 822.0 22 00 5 822.45 22 450 5 822.60 22 600 A concealed fixing rose is available for surface mounting pull handles. Designed to be used with 9mm and 22mm round bar pull handles. The 52mm x 5mm rose mounting converts the pull handle to a concealed 'face fixed' pull. 22Ø 45 Back to back fixing Diameter Centres Item no. (mm) (mm) PS7 SA7 Unit 5 822.8 BB 22 80 pair 5 822.24 BB 22 240 pair 5 822.0 BB 22 00 pair 5 822.45 BB 22 450 pair 5 822.60 BB 22 600 pair Slimline rose Concealed face fixings (included) Suits all pull handle lengths Available in all finishes 50 85.9.6 For 9mm pull handles 50 85.22.6 For 22mm pull handles centres Specification advice For compliance with DocM, we recommend the use of pull handles with 450mm centres or longer. Pull handles are supplied with the appropriate fixing packs for bolt through or back to back fixing. If specifying a bolt through pull handle, appropriate push plates are available for fixing to the push side of the door (see page 2) 9 www.laidlaw.net
ORBIS COMMERCIAL PULL HANDLES Pull Handles Cranked A series of cranked round bar pull handles for bolt through fixing or fixing back to back Supplied complete with fixings to suit timber doors Available in 9mm and 22mm diameters For push/pull applications select an appropriate push plate for the other side of the door (see page 2 for further details) Spare bolt through fixing packs are available (see below) centres A 45 Bolt Through Item no. Ø A Centres SS/PS SA Unit 5 29.0 9 90 00 5 29.45 9 90 450 5 29.60 9 90 600 5 222.0 22 25 00 5 222.45 22 25 450 5 222.60 22 25 600 Back to Back Item no. Ø A Centres SS/PS SA Unit 5 29.0BB 9 90 00 pair 5 29.45BB 9 90 450 pair 5 29.60BB 9 90 600 pair 5 222.0BB 22 25 00 pair 5 222.45BB 22 25 450 pair 5 222.60BB 22 25 600 pair Entrance Pull Handles A series of pillar fixed round bar pull handles for bolt through fixing or back to back Bolt Through 2mm Ø Item no. A C SS/PS SA Unit 5 2.500 500 50 5 2.800 800 650 Supplied complete with fixings to suit timber doors Available in 2mm and 25mm diameters Spare bolt through fixing packs are available (see below) 45 Bolt Through 25mm Ø Item no. A C SS/PS SA Unit 5 25.000 000 850 A C Back to Back 2mm Ø Item no. A C SS/PS SA Unit 5 2.500BB 500 50 pair 5 2.800BB 800 650 pair Back to Back 25mm Ø Item no. A C SS/PS SA Unit 5 25.000BB 000 850 pair Bolt Through Fixing Packs Item no. Description LA58.9 M6 bolt pack for 9mm pulls (SS & PS only) LA58.22 M8 bolt pack for all 22mm, 25mm & 2mm diameter pulls & 9mm pulls in SA finish 0 www.laidlaw.net
ORBIS COMMERCIAL PULL HANDLE FIXINGS Pull Handles Elliptical Section Designed to be compatible with elliptical lever handle design 54 850.25FRS Bolt through or back to back fixing options Choice of lengths available Standard M8 fixing packs suit doors up to 55mm thick other thicknesses to special order Alternative fixing types are also available (see below) Available in SA7 finish only 25 45 5 850. 5 850.45 Bolt through fixing Diameter Centres Item no. (mm) (mm) PS7 SA7 Unit 5 850.0 8 x 25 00 5 850.45 8 x 25 450 Back to Back fixing Diameter Centres Item no. (mm) (mm) PS7 SA7 Unit 5 850.0BB 8 x 25 00 5 850.45BB 8 x 25 450 centres Description Item no. Door thickness Pull handles Pull Handle Fixings Standard Orbis Commercial 5 800 Series bolt through handles are supplied as standard with fixings FPP.5 and back to back handles are supplied with fixing pack FPP5.2. Alternative sizes and fixing types are also available as shown in the table below. FPP Pin side FPP2 Secret face fixing for timber doors with threaded plugs and M8 fixing bolts. For use with Pin side pull handles only M8 x 0mm bolt plus woodscrews to suit concealed roses for 9mmø & 22mmø pull handles FPP FPP2 n/a n/a n/a n/a Thread side Note: Clearance hole for glass door fixings FPP6 and FPP7 4mm Ø FPP Thread side Bolt through fixing for timber doors with CSK M8 bolts. For use with Thread side pull handles only FPP. FPP.2 FPP. FPP.4 FPP.5 40 55mm 40 55mm 5mm 45 65mm 55 65mm 9 & 22ø 5 922 5 922 9 & 22ø 5 922 FPP5 Back to back fixing for timber doors with M8 bolt. For use with one Thread side and one Pin side pull handle. FPP5. FPP5.2 FPP5. 5 55mm 40 55mm 5mm 9 & 22ø 5 922 5 922 Pin side Thread side FPP6 Pin side Thread side Back to back fixing for glass doors with M8 bolt, mmø nylon bush and washers. For use with one Thread side and one Pin side pull handle. FPP6. FPP6.2 FPP6. 0 4mm 0 4mm 0 4mm Glass Door 9ø & 5 922 22ø 5 8 FPP7 Bolt through fixing for glass doors with M8 'Pig nosed' bolt. For use with Thread side pull handles only FPP7. FPP7.2 FPP7. 0 4mm 0 4mm 0 4mm Glass Door 9ø 22ø 5 8 Thread side www.laidlaw.net
Push Plates Designed to be used on the push side of the door with a bolt through or concealed rose fixed pull handle on the pull side. Push plate is used to conceal the bolt through pull handle fixing. Square or radiused corners Supplied with screw fixings Suits bolt through handles up to 600mm centres ORBIS COMMERCIAL PUSH PLATES & KICKING PLATES Item no. corners Size (mm) PS7 SA7 Unit 52 80 radius 50 x 00 52 802 square 50 x 00 52 80 radius 500 x 00 52 804 square 500 x 00 52 805 radius 650 x 00 52 806 square 650 x 00 Entrance Pull Handles Larger pull handles and variants are available to special order. Please contact your Laidlaw Technical Consultant for further information. Kicking & Mid Rail Plates Kicking & mid rail plates must be ordered to suit the height and width required. Special designs are also available to order. Plates are supplied with selftapping wood screws. 2 www.laidlaw.net
ORBIS COMMERCIAL OVERHEAD DOOR CLOSERS Door Closers Orbis Commercial closers are high specification adjustable power closers which have clean and simple lines, ideally suited for use with Orbis Commercial round bar lever furniture Adjustable power units Fully compliant with BS EN 54 where stated Available with 'Softline' or Square allover cover Capable of meeting the requirements for low opening force as required for DDA/ Equality Act applications CE marked & Certifire Approved Fully adjustable for closing speed and latch action Backcheck function Each unit supplied with brackets suitable for fig., fig.6 and fig.66 applications Optional holdopen armsets available (please note; closers with holdopen armsets are NOT CE marked) 2 year guarantee 807 808 Opening and closing forces In order to show compliance with requirements for accessibility, the force needed to open the door, measured at the leading edge, from 0 must be less than 0N (see page 4 for further information). The size of the door, the accuracy of installation of the hardware, the presence of smoke or draught seals, the need to latch the door, the location of the door will all have a bearing on the force required to open it and as a consequence it may not be possible to provide a definitive statement as to which closers do or do not meet the opening force requirements of the regulations. Materials and construction The Orbis Commercial Softline closers have cast aluminium bodies with steel covers, arms and brackets. Square and Softline closer covers are available in the following finishes with arms and brackets to match. Satin stainless steel PS7 Polished stainless steel 'Softline' closers are also available in a range of powder coated coloured finishes (please refer to page 5 for colour options). 807 89 808 892 245 72 72 50 07 60 Note: all dimensions include Softline or Square cover Power sizes The dimensions stated in the chart below relate to closers mounted on the pull side of the door (fig. applications) only. BS EN 54 Power size Door width (mm) Door weight (kg) 20kg 2 40kg 60kg 4 80kg 5 00kg 6 20kg 750mm 850mm 950mm 00mm 250mm 400mm Specification advice Fixed power closers are best suited to internal applications where traffic levels and draught or air pressure is unlikely to vary and where the door size is known. Adjustable power closers can be adjusted to suit door size and site conditions variables that may be unknown at the time of specification. Specifying an adjustable closer can therefore help to avoid installing an underpowered or overpowered unit. HoldOpen closers HoldOpen armsets are available for use with 'Softline' and square covered variants. The use of mechanical holdopen closers is NOT PERMITTED on fire door applications. Closers Arm Pack 807 APH.0 808 APH.02 89 APH.0 892 APH.02 BS EN Classifications Orbis Commercial Softline closers have been fully tested to the requirements of BS EN 54 and have been designated with the Classification no. as shown below. Digit applies to power size and depends on the closer specified. 4 8 24 Insert power size into Classification number www.laidlaw.net
ORBIS COMMERCIAL OVERHEAD DOOR CLOSERS Electromagnetic Controls Designed for use on fire/smoke doors. The unit is controlled by the building fire/smoke detector and alarm system. On operation of the alarm, the integral holdopen mechanism is released and the door closes in the normal manner Fixed power variants Fully compliant with BS EN 54 and BS EN 55 where stated CE marked where stated in table Fully adjustable for closing speed and latch action Available in projecting arm and track arm configurations Fully fire tested to BS EN 64 and suitable for use on fire doors up to 2hr rating 2 year guarantee 27 892.0 27 89.0 27 85 27 854 27 855 27 85 27 858 280 27 892.0 27 89.0 27 894.0 280 570 TBA 25 76 76 49 2 280 49 9 2 Operating Modes Fixed strength projecting arm models are site selectable for either 'holdopen' or 'swingfree' operation. Hold open angle is available from 75 up to 05. The 'swingfree' facility allows the door to operate as if no closer were fitted. When the power to the closer is cut, or in the event of alarm activation, the closer is reactivated and closes the door. Materials and construction The Softline electromagnetic closers have extruded aluminium bodies with covers, arms and brackets in steel. DDA applications Both operating modes of the electromagnetic door control facilitate access and are specifically recommended in the Building Regulations as a means of satisfying the opening force requirements. Specification advice When specifying the track arm electromagnetic closer variants please note that 27 892 & 27 89 closers must be specified as either 'Pull Side' or 'Push Side' application as follows: 27 892.0. Swing Free Push Side 27 892.0.2 Swing Free Pull Side 27 89.0. HoldOpen Push Side 27 89.0.2 HoldOpen Pull Side Electrical requirements Operating voltage 24v DC (+0% 5%) at 2W max. with the exception of 27 894.0 (.4W max.) closers with 'Softline' covers Features & Functions closers with square covers Power size (see chart above) Grade of opening angle (see note #) Adjustable closing speed Adjustable latch action Adjustable back check Optional holdopen armset Mechanical Controls 807 89 2 4 4 808 892 2 6 Fixed power or spring power adjustable adjustable adjustable BS EN 54 compliant & CE Marked BS EN 55 compliant & CE Marked Projecting arm (P) or Track arm (T) P P Electromagnetic holdopen 4 27 85 27 856 fixed P 4 27 854 27 857 4 fixed P 4 Electromagnetic Controls 27 855 27 858 5 fixed P 4 27 892.0 27 89.0 27 894.0 fixed fixed T T T Electromagnetic swingfree 4 adjustable Certifire Approved # Grade 4 will close a door from 80 opening angle. Grade will close a door from 05 opening angle 4 www.laidlaw.net
ORBIS COMMERCIAL FLOOR SPRINGS Floor Springs A series of floor springs is available offering a high level of sophisticated door control specifically for high traffic locations. The range includes a wide selection of accessories to suit timber, metal and glass doors. Fixed power sizes to 6 suitable for doors up to 00kg Variable power unit, size 4 Fully compliant with BS EN 54 and BS EN 55 where stated CE Marked Certifire Approved (cert. no. 28) Fully adjustable for closing speed and latch action Adjustable backcheck Single action and double action Complete with cement box 2 year guarantee Clockwise closing Left hand ISO. 5.0 Anticlockwise closing Right hand ISO. 6.0 Electromagnetic Option Electromagnetic holdopen and freeswing versions are available. When connected to the building fire alarm/detection system, the door can be allowed to swing free or be held open in high traffic locations. On activation of the fire/smoke detection system the electromagnet will be deactivated and the door will close under normal spring power. The hold open position is adjustable between 75 and 80. Electromagnetic versions conform to EN 55. Complete with plug connector for 24V supply. Electrical requirements Operating voltage 24vDC + 5%, residual ripple max. 0% Power input 2.W Features & Functions Power size (see note below) * Fixed power or spring power adjustable BS EN 54 compliant & CE Marked BS EN 55 compliant & CE Marked Certifire Approved for fire doors Grade of opening angle (see note #) Adjustable closing speed Adjustable latch action (5 0 ) Adjustable back check Adjustable delayed closing action Mechanical holdopen Electromagnetic holdopen Electromagnetic swingfree Item no. 0 86/DA 0 864/DA 0 866/DA / 4 / 6 fixed 4 0 864/F 0 865/F 0 866/F 4 / 5 / 6 fixed 4 0 764 0 764/DA 0 764/HO 4 spring 4 0 764/DA 0 764/HO 0 864/HO 0 865/HO 0 866/HO 4 / 5 / 6 fixed 4 0 864/FS 0 865/FS 0 866/FS 4 / 5 / 6 Max. leaf weight (kg) 00 00 20 00 00 fixed 4 # Grade 4 will close a door from 80 opening angle Power size * With the exception of the 0 764 model, the Orbis Commercial floorsprings are fixed power units and must be ordered to suit each application. Use the product reference from the chart above according to the power size required. For example, a 0 86/DA is power size ; a 0 864/DA is power size 4; and 0 866/DA is power size 6. 5 www.laidlaw.net
ORBIS COMMERCIAL FLOOR SPRINGS A Door width (mm) Door weight (kg) 750mm 850mm 950mm 00mm 250mm 400mm B E C Dimensions (mm) 0 764 all others A 50 60 B 82 78 C 285 4 D 08 58 E 05 05 BS EN 54 Power size 20kg 2 40kg 60kg 4 80kg 5 00kg 6 20kg D Power sizes Orbis floorsprings are fixed power (except 0 764 which is adjustable power). Please contact your Laidlaw Technical Consultant for further information. Accessories for action doors 56 Accessories for double action doors 29 0 5 min. 29 0 56 5 20 29 02 24 29 00 25 Accessories A wide range of accessories is available for use with the Orbis Commercial range of floorsprings. The selection of appropriate accessories relates to the type of door and the use of action or double action doors. For glass door fittings and additional accessories for metal, glass or timber doors please contact your Laidlaw Technical Consultant for further advice. Accessories for action doors Item no. Description Finish 29 02 Door strap for bottom of door suitable for flush doors Zinc plated 29 0 Top centre with eccentric pin. Suitable for flush doors non handed Zinc plated 29 06/L Cover cap for door strap Left Hand Mill Finish 29 06/R Cover cap for door strap Right Hand Mill Finish 29 07 Double cover caps for top centres Mill Finish Accessories for double action doors Item no. Description Finish 29 00 Door strap for bottom of door Zinc plated 29 0 Adjustable top centre c/w frame and door portion Steel 6 www.laidlaw.net
ORBIS COMMERCIAL FIRE DOOR CONTROLS Electromagnetic Door Holders Wall and floor mounted electromagnetic door holders are used in conjunction with either an overhead door closer or floor spring. When connected to the building fire/smoke detection and alarm system they will allow a fire door in a high traffic location, such as a corridor, to be held open during normal use. In an emergency situation the holder is deactivated and the door closes under the action of the door closer. The door can always be pulled manually off hold open to allow the door to close. Fully compliant with BS EN 55 CE Marked Surface or semi recessed wall mounting Builtin test button to simulate alarm conditions Floor mounting bracket option Max. holding force 200 Newtons 2 year electrical guarantee 27 5. 27 5 27 5 FMB 86 24 25 46 Finish SS Item no. Description PCP SE 27 5 wall mounted semi recessed 27 5. surface mounting case for use with 27 5 27 5FMB floor mounting bracket Specification advice The holdopen device should be sited at the same level as the closing device (or as close as practical) to minimise the stress placed on the door whilst it is being held open. A skirting mounted holdopen unit used in conjunction with an overhead door closer could induce the door to twist, causing the door to fail to close fully. Power for the electromagnet must not be drawn from the fire alarm system except in alarm condition. A separate power supply is designed specifically for the electromagnetic units (see below). BS EN Classifications Orbis electromagnetic holdopen units have been fully tested to the requirements of BS EN 55 and have been designated with the Classification no. as shown below. 5 6 Electrical requirements Operating voltage 24vDC (22v min / 0v max.) 50mA nominal A series of transformer/rectifiers with facilities for plug in relays are available to power or multiple units. Transformer/rectifier Item no. For holdopen units Max. no of units 27 4 27 5 & 27 54 4 27 20 27 5 & 27 54 20 27 50 27 5 & 27 54 50 Orbis electromagnetic holdopen units are available in applied finishes. SS and PCP are electro plated to match and PS7. The SE finish is a sprayed silver finish to suite with SA7 products. 7 www.laidlaw.net
ORBIS COMMERCIAL HINGES Ball Bearing Hinges Ball bearing hinge Exceed BS EN 95 grade suitable for doors up to 20kg (Weight based on hinges per door leaf) Tested to BS752 class Radiused and square corner versions Stainless steel versions are Grade 04 Supplied with 2mm x No.0 pozidrive stainless steel woodscrews Machine screws available on request for metal doors/frames Security stud option 7 80. 7 800. Radiused corner hinges Item no. Size (mm) 7 800. 02 x 76mm 7 80. 02 x 02mm 7 80. 02 x 76mm with stud Square corner hinges Item no. Size (mm) 7 800.2 02 x 76mm 7 80.2 02 x 02mm 2 80.2 02 x 76mm with stud PS7 PS7 SA7 SA7 Unit Unit 7 80.2 7 800.2 0mmR 4 0mmR 0 02 02 02 02 2.5 2.5 Specification advice Ball bearing hinges are suitable for all types of internal and external applications. When used on fire doors, intumescent packs need to be specified IP H to suit 76 x 02mm hinges IP H2 to suit 02 x 02mm hinges Note: Each intumescent pack contains intumescent material for a pair and a half of hinges. For 0 min. fire door applications specify intumescent pack per pair and a half of hinges. For 60 min. fire door applications specify 2 intumescent packs per pair and a half of hinges. Rising Butt Hinges Rising butt hinges suitable for light internal doors, providing a soft 'self closing' action Must be specified as Clockwise Closing (CW) or AntiClockwise Closing (ACW) Stainless steel versions are Grade 04 Supplied with 2mm x No.0 pozidrive zinc plated woodscrews Maximum adjusted door weight 60kg 2 hinges per leaf recommended Require regular maintenance year guarantee 7 879.5 7 879.6 29 Rising butt hinges Item no. Handing 7 879.5 CW closing 7 879.6 ACW closing Clockwise closing Left hand ISO. 5.0 Anticlockwise closing Right hand ISO. 6.0 SSS Unit 02 SSS Satin Stainless Steel 8 www.laidlaw.net
ORBIS COMMERCIAL MORTICE CYLINDER LOCKCASES Euro Profile Mortice Lockcases An integrated series of modular euro profile cylinder mortice lockcases designed to meet the requirements of BS EN 2209 Precision manufactured slimline case with 6 function variants Modular design allows interchangeability of lock models Meets the requirements of BS EN2209 and with the dimensional characteristics of DIN825 60mm backset 72/78mm centres Bolt through fixings at lever and cylinder positions 20mm double throw deadbolt Quick reversible latchbolt without opening the lockcase Nightlatch with holdback function Springing suitable for unsprung lever furniture Cylinder operates deadbolt and latchbolt Single piece forend in grade 04 stainless steel with matching strike plate Optional radiused or square forend styles Meets BS 800 dimensional recommendations making it suitable for DDA applications Rebate kits available, see page 2 86R Radiused forend Item no. Function 86R latch only 86R sashlock 2 86R deadlock 862R bathroom lock 0 862R cyl. nightlatch* 86R escape sashlock Square ended forend Item no. Function 86 latch only 86 sashlock 2 86 deadlock 862 bathroom lock 0 862 cyl. nightlatch* 86 escape sashlock SA7 SA7 Unit Unit Specification advice Escape sashlocks do not have split follower function. It must be used with a half set of levers on the inside of the door. It must not be used with an internal cylinder thumbturn or external handle. When used on fire doors, intumescent packs need to be specified IP L For Orbis Commercial Sashlock, Bathroom Lock and Nightlatch lockcases IP L4 For Orbis Commercial Deadlock and Latch lockcases For 0 min fire door applications specify pack per lockcase. For 60 min fire door applications specify 2 packs per lockcase. 9 20 25 9 2 72 45 5 2 2,5 46 72 6 65 8 25 85 50 72 45 5 2 2,5 46 78 6 65 5 8 8 60 60 5 8 86R sashlock * Cylinder nightlatches have holdback function 9 www.laidlaw.net
ORBIS COMMERCIAL MORTICE CYLINDER LOCKCASES Dual Profile Mortice Lockcases Radiused forend An integrated series of modular cylinder mortice lockcases which are suitable for use with oval or euro profile cylinders Designed to meet the requirements of BS EN 2209 Modular design allows interchangeability of lock models 57mm backset Bolt through fixings at lever and cylinder positions at 8mm centres (excluding nightlatch) Single throw deadbolt with saw resistant rotating steel pins Quick reversible latchbolt without opening the lockcase Springing suitable for unsprung lever furniture Patented adjustable spring tension allows fine tuning of the lock springing to suit heavier or drooping levers 2 part forend in grade 6 stainless steel with matching strike plate Optional radiused or square forend styles Suitable for use with 56mm centres oval profile or 57mm centres euro profile cylinders Nightlatch has antithrust and holdback functions Rebate kits available, see page 2 2 85 85 85 Item no. Function 85R latch only 85R sashlock 2 85R deadlock 852R bathroom lock 0 85R nightlatch Square ended forend Item no. Function 85 latch only 85 sashlock 2 85 deadlock 852 bathroom lock 0 85 nightlatch SA7 SA7 Unit Unit Specification advice Please note that a conversion plate is fitted to the lockcase suitable for euro profile cylinders. The plate must be removed for use with oval profile cylinders. 25 25 8 8 6 6 8 56/57 24 08 65 46 57 24 08 57 57 76 76 2 85 deadlock 20 www.laidlaw.net
ORBIS COMMERCIAL CYLINDERS & REBATE SETS Cylinders Suitable for use with all Orbis Commercial cylinder mortice lock cases Single cylinder Length 40mm Euro profile 0 80. Oval profile 0 802. Patented 6 pin security until December 204 EN 0 Grade 6 Key security EN 0 Grade 6 Durability EN 0 Grade 2 Attack Resistance (when used with a 0 80 security escutcheon) Unique raised plug with slotted face Improved key strength Patented key blanks are restricted for greater key control and security Euro profile, oval profile, rim and rim mortice cylinders available Range of euro and oval profile cylinder lengths Available as masterkeyed or standard differ variants. Supplied with 2 differ keys Available in satin nickel and polished chrome to match and PS7 finishes 2 year guarantee 0 80. 0 82. 0 8. 0 805. 0 variable Single thumbturn Double cylinder Double cylinder & turn 45mm 50mm Length 40mm 45mm 50mm Length 60mm 70mm 80mm Length 60mm 70mm 80mm 0 80.2 0 80. Euro profile 0 8. 0 8.2 0 8. Euro profile 0 82. 0 82.2 0 82. Euro profile 0 8. 0 8.2 0 8. 0 802.2 Oval profile 0 82. 0 82.2 Oval profile 0 822. 0 822.2 0 822. Oval profile 0 82. 0 82.2 0 82. 60/70/80 60/70/80 4 Rim cylinder Rim mortice cylinder Cam lock 4Ø 25 2Ø 27 0 805. 0 804. 0 806. 0 804. 0 805. Scandinavian Internal Scandinavian External Scandinavian Pair Int/Ext 0 80 0 Cam locks Where a complete masterkeyed system is required, even cupboards or cabinets can be included on the system Scandinavian cylinders Where scandinavian locks are used, corresponding cylinders are available to suit internal and external variants 9.5 25 25 25 0 806. 22 0 807. 0 808. 0 809. Specification advice Select the cylinder length to suit the combined thickness of the door and the hardware. The minimum cylinder projection is required for visual and security reasons. For locks fitted offcentre within the door thickness, offset cylinders are available to special order. Rebate Sets for Cylinder Locks The rebate set will convert the meeting stiles of a rebated pair of doors so that the standard mortice lock can be used. 08 85 Rebate kit Lock ref: mm 0 862 005 86 00 86 00 2 86 007 Rebate kit 25mm Steel Back Box 25 006 4 02 25 004 4 022 25 004 4 022 25 008 4 02 Available in mm and 25mm rebate depths (see chart) Suitable for square forend locks only Steel back box available 86 005 862 00 85 08 855 08 854 85 08 85 08 852 25 006 4 02 25 004 4 022 2 85 08 857 08 856 852 08 85 08 852 0 85 08 85 08 850 2 www.laidlaw.net
Card frames Slide in inserts are suitable for engraving or for applied lettering/ graphics. ORBIS COMMERCIAL SIGNS & SYMBOLS Item no. Description PS7 SA7 Unit 60 90. Card frame 60 x 60mm 60 90.2 Card frame 80 x 60mm Screw fixings are concealed by the insert Clear perspex insert to allow cards to be inserted Tactile Symbols Orbis tactile signs incorporate a combination of visual identification, Braille, raised symbols and letters to assist visually impaired people to locate facilities within a building. High contrast ivory on dark blue signs Self adhesive back for easy fixing to most flat surfaces 60 00. 60 00.2 Item no. Symbol PVC Unit 60 00. male 60 00.2 female 60 00. disabled 60 00.4 baby change 60 00.7 telephone Disability Discrimination The use of tactile signage is a requirement of Part M2 of the Building Regulations 99 and it is recognises the use of tactile signs ensures people with visual impairments are considered under the requirements of the Disability Discrimination Act. Symbols A comprehensive range of face fixed symbols for general application in WC and washroom facilities and on fire door applications. 60 60 60 602 60 60 60 604 60 67 Supplied with face fixing screws 76mm diameter Available in all finishes Fire signs comply with BS5499:5 2002 60 68 60 69 60 620 60 605 60 606 60 607 60 608 60 609 60 62 Item no. Symbol SS PS SA PA Unit 60 60 Fire Door Keep Shut 60 602 Fire Door Keep Locked 60 60 Fire Door Keep Locked Shut 60 604 Keep Locked Shut 60 605 Male 60 606 Female 60 607 Disabled 60 608 Unisex 60 609 Shower 60 67 Automatic Fire Door Keep Clear 60 68 Fire Door Keep Clear 60 69 Fire Exit Keep Clear 60 620 Fire Door Keep Closed 60 62 Baby Change 60 622 WC 60 62 Push 60 624 Pull 60 622 60 62 60 624 22 www.laidlaw.net
www.laidlaw.net ORBIS COMMERCIAL SIGNS & SYMBOLS Fire Exit Signs 60 4. 60 4.2 Fire exit signs are used on doors, emergency or fire escape routes. The Orbis Commercial range of fire exit signs incorporates 75mm letter height to comply with Fire Precautions Act 97 and include 'symbol only' versions to suit EC Council Directives. Designed to comply with EC Council Directive 92/558/EEC and Fire Precautions Act 97 Supplied with woodscrews or self adhesive pads for alternative fixing method All signs available in the following finish and fixing combinations: Aluminium screw fixed Aluminium self adhesive Vinyl self adhesive Plastic screw fixed Plastic self adhesive Photoluminescent Signs The signs shown on this page are also available in photoluminescent material which are energised by exposure to light. When the light source fails, the material emits a highly visible luminescense which lasts for several hours. The natural photoluminescent daylight colour of light green has been officially recognised in BS 5499 and BS 578 as suitable for use in safety signs. Sizes The standard signs are available in the sizes shown. All the signs are available in other sizes to special order. 60 0. 60 42. 60 42.2 60 4. 60 4.2 60 44. 60 44.2 60 4. 60 4.2 60 0. 00mm x 60mm 60 02. 00mm x 60mm 60 0. 00mm x 60mm 60 47. 60 47.2 60 46. 60 46.2 60 04. 00mm x 60mm 60 45. 60 45.2 60 48. 60 48.2 Dimensions. 00mm x 240mm.2 50mm x 60mm 60 04.2 200mm x 600mm Please Note The signs shown on this page are for identification purposes only. They are not shown to scale, please refer to the dimensions shown. 60 07 75mm x 50mm 60 055 50mm x 50mm 60 060 00mm x 40mm 2 www.laidlaw.net 60 05 225mm x 225mm 60 062 00mm x 40mm 60 070 75mm x 50mm 60 056 50mm x 280mm 60 06 00mm x 40mm 60 072 75mm x 50mm 60 054 40mm x 470mm 60 052. 65mm x 280mm 60 052.2 0mm x 565mm 60 07 75mm x 50mm
www.laidlaw.net ORBIS COMMERCIAL SIGNS & SYMBOLS Safety & Security Signs Safety and security signs are mandatory and require a specific behaviour or action to be taken. By separating the symbol and the wording the signs are designed to comply with EC Council Directive 92/58/EEC. Designed to comply with EC Council Directive 92/58/EEC All signs white lettering on blue background Supplied with woodscrews or self adhesive pads for alternative fixing method Dual language signs in Welsh and English are also available All signs available in the following finish and fixing combinations: 60 0 Sizes Signs 60 00 to 60 048 are 80mm x 80mm. Signs 60 45.2 & 60 46.2 are 400mm x 00mm. Signs 60 45. & 60 46. are 200mm x 50mm. 60 45.! Aluminium screw fixed Aluminium self adhesive Vinyl self adhesive Plastic screw fixed Plastic self adhesive 60 45.2 400mm x 00mm! 60 06 Other sizes available to order along with nonstandard signs. Please contact your Laidlaw Technical Consultant for further details.! Please Note The signs shown on this page are for identification purposes only. They are not shown to scale, please refer to the dimensions shown. 60 46.2 400mm x 00mm! 60 45. 200mm x 50mm 60 46. 200mm x 50mm 60 00 60 0 60 02 60 0 60 04 60 05 60 06 60 07 60 08 60 09 60 040 60 04 60 042 60 04 60 044 60 045 60 047 60 048 24 www.laidlaw.net
Door Stops & Skirting Buffers Designed to fix onto the wall, skirting or floor to limit the opening of the door and to protect door hardware from damage Skirting mounted options Rose fixed skirting option Wall or floor mounted Range of projections to suit different hardware ORBIS COMMERCIAL DOOR STOPS & HOLDERS Skirting buffer Item no. Projection 2 800. 75mm 2 800.2 95mm Concealed rose fixed Item no. Projection 2 80. 75mm 2 80.2 95mm PS7 PS7 SA7 Unit SA7 Unit 2 80. 2 800. 2 800.2 2 800. & 2 800.2 2 80. 2 8 Wall or floor mounted Item no. Projection 2 8 40mm PS7 SA7 Unit 9Ø 75 / 95 52Ø 75 / 95 52Ø 29 Floor mounted Item no. Projection 2 802 24.5mm 2 80 40.5mm SS PS SA Unit 24.5 Door Stops & Door Holder Designed for floor mounting in timber or solid substrates. The dual purpose door stop & holder will act as a door stop and can be pushed down to act as a door holder. 2 845 2 850 Lockable Item no. Face Plate 2 840 round 45mm 2 85 square 45mm PS7 SA7 Unit Dual purpose stop/holder High resistance to deforming under heavy usage Lockable versions can be held in the retracted position Available with round or square face plate Grade 6 stainless steel 00,000 cycle tested Installation kit included 2 85 2 840 Nonlockable Item no. Face plate 2 850 round 45mm 2 845 square 45mm PS7 Specification advice Door holders must not be used on fire door applications. SA7 Unit 52 45 25Ø 25Ø 52 20 2.5 20 2.5 45Ø 45Ø 5Ø 29Ø 2 802 40.5 2 80 25 www.laidlaw.net
ORBIS COMMERCIAL PULLS, HOOKS & WC FITTINGS Flush Pulls Supplied with selftapping screws for surface fixing Flush pull suitable for doors 20mm thick minimum Available in all finishes 50 00 6 800 Flush pull Item no. Size (mm) 6 800 00 x 50 PS7 SA7 Unit Cylinder Pulls 62 800.0 62 800. 62 800.2 A series of face fixed cylinder pulls suitable for use with rim nightlatches and mortice nightlatches. Supplied with selftapping screws for surface fixing All locking and cylinder types included 62 800. 62 800.8 Cylinder pulls Item no. Function 62 800.0 blank PS7 SA7 Unit 62 800. lever key locks 62 800.2 oval profile cylinder 62 800. euro profile cylinder 62 800.8 round (rim) cylinder 45 8 Hooks & WC Fittings A compact series of hooks and wc fittings. Additional items may also be available from the Orbis Premier Series of hardware. Hooks Item no. Function PS7 SA7 Unit 8 80 hat & coat hook 8 802 buffered hat/coat hook 8 80 robe hook 8 804 buffered robe hook 8 80 8 804 8 802 8 80 80 802 Indicator bolt Item no. Size (mm) 89 00 62 x 40 x 0 SCP Unit 89 90 75 x 52 /PS7/SA7 89 90 89 00 WC roll holder Item no. Size (mm) PS7 SA7 Unit 80 802 49 x 74 x 80 802 0 x 72 x 28 26 www.laidlaw.net
ORBIS COMMERCIAL FLUSH & SLIDE BOLTS Flush Bolts A series of lever action flush bolts, primarily intended for mounting in the leading edge or inside face of the normally closed leaf of a pair of doors or a leaf and a half. Smooth lever action Range of lengths to suit different door heights mm diameter shoot Radius end and square end variants 4 005. 4 005.2 4 007.2 4 005. Square ended bolts Item no. Length PS7 SA7 Unit 4 005. 50mm 4 005.2 200mm 4 005. 00mm Radius ended bolts ESS Item no. Length EPS SA7 Unit 4 007. 50mm 4 007.2 200mm 4 007. 00mm Square end SS and PS finish flush bolts are made from 8mm wide section. All radius end and SA square end flush bolts are made from 20mm wide section. Flush Bolts Knob Slide A series of sliding knob flush bolts designed for mounting on the inside face of the normally closed leaf of a pair of doors or a leaf and a half. Smooth slide action Range of lengths to suit different door heights mm diameter shoot 4 006.2 Knob slide bolts PCP Item no. Length SCP SA Unit 4 006. 52mm 4 006.2 229mm 4 006. 05mm Surface Bolts A series of surface mounted bolts in straight and cranked formats. Range of lengths to suit different door heights 0mm diameter shoot All bolts 5mm wide Supplied with selftapping screws 4 00.2 4 00. 4 0.2 Surface bolt straight Item no. Length PS7 SA Unit 4 00. 50mm 4 00.2 200mm 4 00. 250mm Surface bolt cranked Item no. Length 4 0. 00mm 4 0.2 50mm ESS EPS SA Unit Bolt Sockets Sockets for flush bolts. Floor mounted, suitable for mm diameter shoots only. Easy clean variant Sprung loaded dust excluding variant Suitable for timber or concrete floor substrates Suits mm diameter shoot 4 028 4 029.4 Floor sockets Item no. Type 4 028 easy clean 4 029.2 dust excluding 4 029.4 dust excluding SCP Note: 4 029.2 has a rectangular face plate SA Unit 27 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE A final exit door must be fitted with a securing device which enables the occupants of a building to open it without the use of a key from the escape side. 28 www.laidlaw.net
Pushbar Devices A modular system of panic exit hardware which is operated by a horizontal 'Pushbar' design. The device can be cut on site and is suitable for doors up to 00mm wide. Touchbar Devices A modular system of panic exit hardware which is operated by a horizontal 'Touchbar' design. Two lengths of device are produced, and can be cut on site to fit doors up to 940mm or 00mm wide. The visual simplicity and low projection of the 'Touchbar' device makes it ideal for any building where aesthetics are an important consideration. ORBIS COMMERCIAL PANIC EXIT HARDWARE Every new build or replacement panic exit application is required to comply with European safety legislation. The European standard BS EN 25 covers panic exit devices for buildings used by the public providing "safe and effective escape through the doorway with minimum effort and without prior knowledge of operation". Orbis Commercial panic exit hardware carries the CE mark visibly showing that the products have been independantly tested and assessed to the very latest European standard. From April 200 it became mandatory for all manufacturers to CE mark exit devices for fire and escape door use. Orbis Commercial panic exit hardware conforms to BS EN 25 and carries the CE mark under certificate of conformity number 0099CPBA44. Security Designed to provide immediate escape at any time these devices also provide a high level of security from intruders from the outside. The antithrust device prevents unauthorised retraction of the latchbolts and the modular design allows various levels of multipoint locking. Orbis Commercial Panic Exit Hardware Suitable for most timber, steel, and aluminium door constructions up to a maximum mass of 200kg, a maximum height of 2500mm and a maximum width of 00mm The device is suitable for doors with a minimum clear opening width down to 500mm. This can be reduced to 50mm when the side latchbolts are not required Antithrust device prevents unauthorised retraction of the latchbolt Stainless steel latchbolts as standard Supplied complete with adjustable strikers and spacers for accurate installation on both and double door applications. 5 year guarantee Modular components The Orbis Commercial series offers increased levels of flexibility with its modular design feature. For example, should the need arise for increased security, upgrading a device is simple. The one point locking device can be easily upgraded to two, three or even four point locking on a door for maximum security. In the same way, double door applications can be increased from three point locking up to six point locking. The modular design feature means that there s no need to replace the whole device when upgrading, simply select the locking kit you require. The modular components can be applied to the 'Pushbar' or 'Touchbar' operating unit. 29 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE The Modular Approach. Firstly select which device you wish to use, either a Panic Pushbar or a Panic Touchbar Finish: Silver/Coloured/Metallic (see p9) Specification advice Remember to select the correct length of Touchbar unit to suit the door width (see page 6). 59 86 One point Panic Pushbar Device 59 87. & 59 87.2 One point Panic Touchbar Device See application guides on pages 4 and 6 for details 2. Choose the most suitable modular locking point configuration. For increased security there is the option of an additional modular locking point. Finish: Silver/Matt black 59 88 Upper & Lower Pullmans Kit 59 882 Two Side Pullmans Kit 59 88LH & 59 88RH Upper & Side Pullmans Kit 59 884LH & 59 884RH Additional Side Pullmans Kit. Select the rod kit to connect the locking units to the panic device. Finish: Silver/Matt black 59 885 Upper & Lower Rod Kit Clockwise closing Left hand ISO. 5.0 Anticlockwise closing Right hand ISO. 6.0 Controlled Access Outside access device for use with both Orbis Commercial Pushbar and Touchbar devices. Using an Orbis outside locking device will give access from the outside for key holders when the door is locked. When unlocked the door can also be operated from the outside by using lever/knob. Choice of interchangeable knob, or lever (available separately) allowing the most appropriate method of operation to be selected for the building users. 45 64 8 6 4.LE & 6 4.KE Outside Access Devices Supplied with europrofile cylinder as standard. Cylinders can be keyed alike or masterkeyed Suitable for door thickness 40mm 70mm Fixings supplied are suitable for timber and metal doorsets Tested to 200,000 cycles Powder coated for additional durability choice of silver, matt black, gold, brown bronze or Normbau finishes Choice of plated finishes satin stainless steel and polished brass For all other forms of access control (digital, electronic etc) please contact your local Laidlaw Technical Consultant. 59 889 Top Rod Extension Kit Rod extension kits are suitable for use with both Orbis Commercial panic devices on doors in areas that require the pushbar or touchbar to be in a lower position ie schools. These can also be used on doors up to 50mm high, however doors over 2500mm high are outside the scope of BS EN 25. Finish: silver/matt black 0 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE Pushbar range 59 86 Single point locking 59 862 Two/Three point locking 59 86 Three point locking 59 864 Three point locking A point locking panic device Two/Three point locking panic device with upper and lower pullmans Three point locking panic device with two side pullmans Three point locking panic device with one upper and one side pullman Suitable for use on doors and the first opening leaf of rebated double doors Upgradeable to two/three point locking or four point locking on and first opening leaf of rebated double doors with Modular Locking Points (see page 4 for details) Nonhanded suitable for both left and right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Conforms to BS EN 25 Suitable for use on doors, rebated and nonrebated double doors Upgradeable to four point locking on doors with Modular Locking Points (see page 4 for details) Nonhanded suitable for both left and right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Alternative bottom striker option available (see page 9 for details) Conforms to BS EN 25 Suitable for use on doors and the first opening leaf of rebated double doors Upgradeable to four point locking on doors and first opening leaf of rebated double doors with Modular Locking Points (see page 4 for details) Nonhanded suitable for both left and right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Conforms to BS EN 25 Suitable for use on doors Upgradeable to four point locking on doors with Modular Locking Points (see page 4 for details) Handed 562VS/L suitable for left handed doors & 562VS/R suitable for right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Conforms to BS EN 25 Classification 76422A Classification 76422A Classification 76422A Classification 76422A Clockwise closing Left hand ISO. 5.0 Anticlockwise closing Right hand ISO. 6.0 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE Application guide Pushbar range Orbis Commercial panic exit devices are suitable for application to doors and in combinations on rebated and nonrebated double doors. Specification advice Consideration should be given to the use of door coordinating devices for rebated pairs of doors. A door coordinating device must be used for fire/smoke applications. Single Doors One point locking Three point locking Three point locking Two or Three point locking Side latchbolt can be disabled during installation 59 86 59 86 59 864 59 862 Rebated Double Doors Rebated Double Doors NonRebated Double Doors Three point locking Five point locking Four point locking 59 86 59 862 59 86 59 862 59 862 59 862 57 6 57 6 5 5 57 6 4 6 5 45 4 08 50 5 4 96 200 00 6 54 77 77 0 5 2 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE Touchbar range 59 87. (200mm) 59 87.2 (840mm) Single point locking 59 872. (200mm) 59 872.2 (840mm) Two/Three point locking 59 87. (200mm) 59 87.2 (840mm) Three point locking 59 874. (200mm) 59 874.2 (840mm) Three point locking A point locking panic device Two or Three point locking panic device with upper and lower pullmans Three point locking panic device with two side pullmans Three point locking panic device with one upper and one side pullman Suitable for use on doors and the first opening leaf of rebated double doors Upgradeable to two/three point locking or four point locking on and first opening leaf of rebated double doors with Modular Locking Points (see page 4 for details) Nonhanded suitable for both left and right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Conforms to BS EN 25 Suitable for use on doors, rebated and nonrebated double doors Upgradeable to four point locking on doors with Modular Locking Points (see page 4 for details) Nonhanded suitable for both left and right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Alternative bottom striker option available (see page 5 for details) Conforms to BS EN 25 Suitable for use on doors and the first opening leaf of rebated double doors Upgradeable to four point locking on doors and first opening leaf of rebated double doors with Modular Locking Points (see page 4 for details) Nonhanded suitable for both left and right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Conforms to BS EN 25 Suitable for use on doors Upgradeable to four point locking on doors with Modular Locking Points (see page 4 for details) Handed 59 874.LH & 59 874.2LH suitable for left handed doors & 59 874.RH & 59 874.2RH suitable for right handed doors Dogging device (holdopen) option available (see page 5 for details) Alarm microswitch option available (see page 5 for details) Conforms to BS EN 25 Classification 76422A Classification 76422A Classification 76422A Classification 76422A Clockwise closing Left hand ISO. 5.0 Anticlockwise closing Right hand ISO. 6.0 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE Application guide Touchbar range Orbis Commercial panic exit devices are suitable for application to doors and in combinations on rebated and nonrebated double doors. Specification advice Consideration should be given to the use of door coordinating devices for rebated pairs of doors. A door coordinating device must be used for fire/smoke applications. Single Doors One point locking Three point locking Three point locking Two or Three point locking Side latchbolt can be disabled during installation 59 87. 59 87.2 59 87. 59 87.2 59 874. 59 874.2 59 872. 59 872.2 Rebated Double Doors Rebated Double Doors NonRebated Double Doors Three point locking Five point locking Four point locking 59 87. 59 872. 59 87.2 59 872.2 59 87. 59 872. 59 87.2 59 872.2 59 872. 59 872. 59 872.2 59 872.2 KEY TO DIAGRAMS 57 6 5 57 6 5 57 6 Side latchbolt not required disable during installation 64 9 L = 200mm (.) = 840mm (.2) Codes shown relate to modular products. 45 24 0 4 89 50 5 54 77 2 56 4 6 77 5 25 L 6 0 5 4 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE Accessories & Alarm Switch Kits These units allow standard models to be connected to electronic audio/ visual alarm or door control systems giving immediate notification of use when the panic device is operated. The door cannot be opened without the system being activated. Accessories for Pushbar Devices only Accessories for Touchbar Devices only Dogging Device (hold open) Kits These units allow standard models to be upgraded to permit free access when required. The manual hold open function is operated by a key and holds all latchbolts in the withdrawn position. Note: Dogging kits should not be used on fire/smoke applications. Finish of Components (see key) 59 866 Alarm Switch 59 867 Dogging Device Option A (SES) Colour coded powder coated Silver Option B Coloured powder coated 59 877 Dogging Device Option C Simulated metallic finishes 59 876 Alarm Switch Option A. Pushbar/Touchbar Silver 2. Casing covers Silver. Pullman covers Silver 4. Rods Silver Option B. Pushbar/Touchbar Choose from powder coated swatches 2. Casing covers Matt Black. Pullman covers Matt Black 4. Rods Matt Black Powder Coated Metallic Metallic Option C. Pushbar/Touchbar Choose from Metallic swatches 2. Casing covers Matt Black. Pullman covers Matt Black 4. Rods Matt Black silver (SE) gold (GE) Powder Coated Coloured brown bronze (BE) satin stainless steel (SS) polished stainless steel (PS) polished brass (PB) Note: S Special Colours may be subject to a longer delivery time. Due to the limitation of the printing process, we suggest you check your final choice of finish against the actual products or a sample swatch white 9 manhattan 67 dark grey 8 black 6 NWH NMG NDG NBL RALDS 000 95 00 RALDS 080 70 05 RALDS 000 5 00 RALDS 000 5 00 yellow 22 NYE RALDS 080 80 90 green NGR red 2 NRE slate blue 6 NSB blue dark blue 7 NBU NDB RALDS 270 0 40 RALDS 270 20 25 dark red 5 NDR ivory 65 NIV RALDS 60 0 8 RALDS 00 0 45 RALDS 240 50 5 RALDS 00 20 25 RALDS 090 85 0 S S 5 www.laidlaw.net
ORBIS COMMERCIAL PANIC EXIT HARDWARE Technical Data 59 86 Construction Pushbar Device The main and end casings are constructed of steel components, mounted on a steel chassis and covered by a precision zinc diecast cover. The stainless steel latchbolt is activated by a tubular steel bar. Touchbar Device The main casing & rear bracket are constructed of steel components mounted on a steel chassis and are covered by a precision zinc die cast cover. The stainless steel latchbolt is activated by an extruded aluminium touchbar enclosed in an extruded aluminium channel. Locking Kits The locking points are constructed of steel components mounted on a steel chassis incorporating a stainless steel latchbolt. Connection to the pushbar or touchbar device is via steel all thread bars and are concealed by an extruded aluminium cover. Maintenance Panic exit hardware plays a vital role in the buildings escape route, and it is important that these devices are inspected and maintained properly to ensure safety at all times. As recommended in EN 25 the following routine maintenance checks should be undertaken at intervals of not more than month by the occupier or his approved representative: Inspect and operate the panic exit device to ensure all components are in satisfactory working condition Ensure that strikers are free from obstruction Fire/Smoke Reference the Fire Precautions Act 97, always consult the Local Fire Officer for their interpretation of the Act before finalising specification. Products within the Orbis Commercial series have been included in successful fire tests to EN 64. Fixing/Installation These surface mounted devices come complete with step by step fixing instructions and fixing templates to ensure an easy and accurate installation. The pushbar, touchbar and rod kits are easily cut to size on site, to suit doors up to 2500mm high by 00mm wide. The devices are supplied with nonstandard tools for convenience, and adjustable strikers with packers to ensure continued optimum performance. Fixing and maintenance instructions must be passed on to the user upon completion of installation. Technical Support If you have any queries regarding Orbis Commercial exit devices and product selection please call your local Laidlaw Technical Consultant who will be pleased to offer assistance on any aspect of specification including queries on: Product selection Advice on installation Trouble shooting Ancillary products and spare parts. Special Applications For special applications outside those mentioned in this catalogue please contact Technical Support who will be able to advise and assist with product selection for nonstandard installations. Supply & Quotations The Orbis Commercial range of panic exit hardware is available through a nationwide network of Laidlaw branches. Other products to EN 25 include Orbis 7 panic and emergency exit hardware. Please contact your Laidlaw Technical Consultant for further details. 6 www.laidlaw.net
STANDARDS & BS EN CLASSIFICATIONS The standards compliance of Orbis Commercial products falls into categories Performance testing to the latest European standards, including CE marking where this is appropriate Suitability for fire & smoke doors with products successfully included on timber and steel door fire tests Compliance with the requirements of Approved Document M of The Building Regulations and BS 800, and thereby considered suitable for use in DDA applications BS EN Standards are the benchmark for product performance in several major product areas within architectural hardware. Each standard prescribes a set of test procedures for products which are selected at random from stock production items. The test data and product evaluation produces a multi digit classification code which runs in parallel across each product area (or as close as practically possible). The relevant BS EN standards are summarised opposite. Further details of these BS EN standards are available from The Association of Builders Hardware Manufacturers at www.abhm.org.uk CE Marking is applicable only to those products where the BS EN Standard has been harmonised under the Construction Products Directive. BS EN 906 is the European standard for 'Lever handles & knob furniture' and is applicable only to items which are used to operate locks or latches. Testing and evaluation results in an 8 digit code. 4 7 67 0 0 0 04 2 04 U ABU Example Orbis 54 80.9FRS lever classification 4740U BS EN 2209 is the European standard for 'Mechanically Operated Locks and Latches'. The standard is wide ranging and covers physical testing of the lock and also classifies it according to the method of operation. Testing and evaluation results in an digit code. BS EN 2209 is harmonised under the Construction Products Directive and CE marking of approved products is permitted. X AX 8 9 0 0 0 F 0G 2 7 B ABU A 0H Example Orbis 86 Lockcase classification H80FBC20 2 04 0 0H Digit Category of Use (Grades to 4) Grade is high frequency use by the public with a high chance of misuse. Digit 2 Durability (Grade 6 or 7) Testing to 00,000 (Grade 6) or 200,000 cycles (Grade 7) Digit Door Mass (No requirement) Digit 4 Fire Resistance (Grade 0 or ) Grade 0 is not suitable for fire door applications Digit 5 Safety (Grade 0 or ) Digit 6 Corrosion Resistance (Grade 0 to 4) Grade is the minimum for external applications Digit 7 Security (Grade 0 to 4) Digit 8 Type of Operation (Type A, B or U) Type U is unsprung lever furniture Digit Category of Use (Grades to ) Grade is high frequency use by the public with a high chance of misuse. Digit 2 Durability (Grades AC, FH, L M R S W & X) A complex range of 2 grades based on a combination of side load and test cycles Digit Door Mass (Grades to 9) A complex grading system based on a combination of door mass and maximum closing force required Digit 4 Fire Resistance (Grade 0 or ) Grade 0 is not suitable for fire door applications Digit 5 Safety (Grade 0 or ) Digit 6 Corrosion Resistance (Grade 0 & AG) Digit 7 Security (Grade to 7) Digit 8 Field of Door Application (Type A to R) Digit 9 Type of Key Operation (Grade 0 & A to H) Digit 0 Type of Spindle Operation (Grade 0 to 4) Digit Key Identification (Grade 0 & A to H) BS EN 54 is the European standard for 'Controlled Door Closing Devices'. The standard measures mechanical door closer performance resulting in a 6 digit classification. BS EN 55 is a parallel standard for 'Electrically Powered Holdopen Devices' and is therefore relevant to Electromagnetic door closers. Such closers must satisfy the requirements of both standards, BS EN 54 and BS EN 55. BS EN 54 and BS EN 55 are both harmonised standards and CE marking became mandatory in 2004 Digit Category of Use (Grades to 4) (Grade ) Defines the angle from which it will close the door Digit 2 Durability (Grade 8 only) (Grades 5 to 8) Grade 8 describes 500,000 test cycles for both standards but is the only grade available in BS EN 54 Digit Door Mass (Grades to 7) (Grades to 7) Identifies the closing power of the closer by max. door width and weight (see chart below) Power size 2 4 5 6 7 4 4 8 8 8 58 7 7 4 04 4 04 BS EN 54 classification BS EN 55 classification Example Orbis 80 Smoothline closer classification 48 max. door size width mm weight kg 750 20 850 40 950 60 00 80 250 00 400 20 Digit 4 Fire Resistance (Grade 0 or ) (Grade ) Grade 0 is not suitable for fire door applications. Grade must be supported by fire tests to BS EN 64 Digit 5 Safety (Grade only) Grade identifies the closer is hazard free Digit 6 Corrosion Resistance (Grade 0 to 4) 600 60 7 www.laidlaw.net
STANDARDS & BS EN CLASSIFICATIONS Fire Testing Individual products are not in themselves fire tested, but are included as an integral part of a fire test carried out on a timber or steel fire door. As a consequence, the details of the test, the construction of the door, the inclusion of intumescent material etc must be considered when specifying products suitable for use on a fire door. Where Laidlaw products are indicated as suitable for fire door applications, the products have been successfully included on the test door which has achieved the stated rating. Laidlaw holds comprehensive test certification for all appropriate products and these are available on request. BS EN 25 & BS EN 79 Products which are designed to provide safe and effective escape from a building in an emergency situation are covered by two European standards which have clearly defined applications. BS EN 25 is the European standard for 'Panic Exit Devices'. The primary determining factor is that a 'Panic' device must be fitted where members of the public are present and have no prior knowledge of the exit or the hardware. BS EN 79 is the standard covering 'Emergency Exit Devices'. In 'Emergency' situations it is assumed the occupants will have prior knowledge of the exit and a panic situation is unlikely to occur. Testing and evaluation to each standard results in a 9 digit code. BS EN 25 and BS EN 79 are harmonised under the Construction Products Directive and products must therefore carry the CE mark. 7 67 6 56 0 4 4 2 2 2 2 Example Orbis 59 87 Panic Device classification 76422B A AB Digit Category of Use (Grades ) Grade is high frequency use by the public with a high chance of misuse. Digit 2 Durability (Grades 6 or 7) Cycle testing, Grade 7 having undergone 200,000 cycles Digit Door Mass (Grades 5 or 6) Determined only by door mass of 00g or 200kg Digit 4 Fire Resistance (Grade 0 or ) Grade 0 is not suitable for fire door applications Digit 5 Safety (Grade only) All panic and emergency exit devices have a critical safety function Digit 6 Corrosion Resistance (Grade or 4) Digit 7 Security (Grade 2 only) (Grade 2 4 in BS EN 79) Digit 8 Projection of Device (Grade or 2) Grade 2 is low projection, less than 00mm Digit 9 Type of Device (Type A or B) BS EN 25 Type A is a pushbar operation BS EN 25 Type B is touchbar operation BS EN 25 Type A is with lever handle operation BS EN 25 Type B is with push pad operation BS EN 95 is the European standard for 'Single Axis Hinges' used on doors and windows. Testing and evaluation of the product results in a 8 digit code. BS EN 95 is harmonised under the Construction Products Directive and products must therefore carry the CE mark. 4 7 47 6 07 0 04 0 0 4 Example Orbis 7 80. hinge classification 76422A Digit Category of Use (Grades to 4) Grade is heavy duty use. Digit 2 Durability (Grades, 4 or 7) Cycle testing, Grade 7 having undergone 200,000 cycles Digit Door Mass (Grades 0 to 7) Table of door mass from 0kg up to 60kg Digit 4 Fire Resistance (Grade 0 or ) Grade 0 is not suitable for fire door applications Digit 5 Safety (Grade only) All hinges have a critical safety function Digit 6 Corrosion Resistance (Grades 0 to 4) Grade is high resistance Digit 7 Security (Grade 0 or ) Grade 0 is not suitable for burglar resistance Digit 8 Hinge Grade (Grades to 4) Grading is by combination of test cycles and door mass. Grade is 200,00 cycles of a door mass of up to 20kg 8 www.laidlaw.net
DDA, APPROVED DOC. M & BS 800 The implementation of legislation in 996 made it a legal duty on those responsible for buildings used by the general public, and employers responsible for places of work, to ensure that the building and its facilities are accessible to disabled people. The aim of The Disability Discrimination Act (DDA) is to make it a duty to avoid discrimination againsts disabled people and this duty requires that Service Providers make "reasonable" adjustments to the design of the building in order to provide this universal level of access. The details on this page are a simple summary of the primary sources of information related to the use of hardware products in order to satisfy disabled access. The Disability Discrimination Act/Equality Act 200 It is important to remember that the Equality Act (which incorporates the previous Disability Discrimination Act) is civil rights legislation and does not set out specific requirements or guidance in the design of buildings. As such it is therefore not appropriate to attach any notion of conformity to products, such as "DDA compliant" or "Conforms to DDA requirements". The legislation came into force on st October 2004. Any new building or alterations to existing buildings, in order to satisfy obligations under the DDA, must comply (in England & Wales) with The Building Regulations, and in particular, the 2004 edition of Approved Document M (ADM) which became effective in May 2004. Where certain issues are not covered in ADM, further reference will be made to BS 800. Further detailed information can be obtained from the following: Office of the Deputy Prime Minister www.odpm.gov.uk Association of Buildiers Hardware Manufacturers www.abhm.org.uk BSI Customer Services cservices@bsiglobal.com Office of Public Sector Information www.uklegislation.hmso. gov.uk Disability Rights Commission www.drcgb.org Guild of Architectural Ironmongers www.gai.org.uk Approved Document M (ADM) The main requirements set out in ADM are, as with all parts of The Building Regulations, performance based and the guidelines set out in the document are recognised as one way of achieving the requirements. The scope of the requirements are clearly set out, requiring that provision is made for people to "a) gain access to and b) use the building and its facilities". This includes the provision of sanitary accomodation in domestic and nondomestic buildings. ADM applies not only to new building but also to alterations and extension of existing buildings. Where certain issues are not covered within ADM, further reference will be made to BS 800. ADM contains a number of very specific requirements for the following aspects related to architectural hardware specification. Accessible Doors ADM recognises that negotiating entrance doors can be difficult for the general public, not just disabled people: parents with children, those carrying luggage or with pushchairs etc. It is stated within ADM that doors which are required to be self closing must require a force no greater than 20N at the leading edge in order to open them. In most practical applications "A powered door opening and closing system... is the most satisfactory solution for most people" (ADM 2.0). Although the 20 Newtons rule technically still exists it has been generally superceded by a twophase criteria established within BS 800 in 2005. This states a maximum opening force of 0N at the initial opening stage (0 to 0 ), reducing to 22.5N from 0 to 60 opening angle. Fire & Smoke Doors BS EN 54 requires fire doors to be held closed by a door closer with a minimum power size. This requires a force in excess of 20N (see chart below) and therefore puts it into conflict with the 20N opening force requirement of ADM. In these circumstances ADM recommends the use of electromagnetic hold open or low energy door operators. For fire doors within corridors the preference is for electromagnetic hold open units. Where privacy is still a requirement, such as doors to individual rooms, an electromagnetic device which offers a 'swing free' facility is preferable. BS EN 54 min. closing moment Min. closing force (moment/door width) BS EN 54 min. closer efficiency Corresponding min. opening force BS EN 54 size 9 Nm 0.59 N 50% 2.8 N Note: calculations are based on a door leaf width of 850mm. BS EN 54 size 8 Nm 2.7 N 55% 8.5 N Internal Doors For internal doors which need to be self closing for privacy or environmental reasons, they must meet the maximum opening force criteria of 20N. In these circumstances a high efficiency variable power door control is required. When set to the lowest strength (size ) to reduce the opening force it may cause problems in latching the door, especially in locations which may be susceptible to drafts or air pressure differences. Locks with a 'soft action latch' and high quality hinges will help in making sure the door latches properly each time. BS 800:200 This standard provides guidance on good practice in the design of buildings to make them suitable for use by disabled people. The standard is often used as a supplement to ADM and includes more specific dimensional guidance, particularly regarding the sizes of door operating hardware. BS 800 contains the following recommendations related to architectural hardware specification. Accessible Doors Aside from the headline figures of ADM, the guidance in BS 800 points clearly to the use of powered solutions including low energy operators to achieve the level of accessibility required on external doors (including recommendations for the positioning of any manual controls. Fire & Smoke Doors Doors to escape stairs and final exit doors are not specifically covered in ADM. In BS 800 it is considered suitable to use a conventional door closer in these cases, as such doors are likely to be opening in the direction of escape (ie push to exit). In these situations BS 800 recommends a maximum opening force of 0N. Closing & Opening forces As can be seen from the chart opposite, a door closer power size with only the minimum efficiency allowed in the EN standard (50%) will not satisfy the maximum opening force to satisfy the 20N limit in ADM. Also clearly evident is the fact that a power size closer (the min. allowed in satisfying the requirements for a fire door) has an opening force at the edge of the door beyond the 0N maximum allowed in the revised regulations. Only high efficiency closers will therefore meet the dual requirements for an accessible fire door. 9 www.laidlaw.net
DDA, APPROVED DOC. M & BS 800 Lever handle dimensions 9mmØ 'generous length' Lock & latch critical dimensions BS 800 54mm minimum 45mm minimum 72mm minimum Approved Document M (ADM) Door Opening Hardware Guidance on the specification for door hardware falls into 2 main categories ability to grip and operate the hardware ability to visually locate the hardware Ability to grip and operate the hardware The requirement within ADM is that "where fitted with a latch, the door opening furniture can be operated with one hand using a closed fist, e.g. a lever handle" (ADM 2.7). Whilst no specific dimensional requirements are laid down in ADM, such recommendations are covered in BS 800. It is a requirement of ADM that external handles (ie those used to open manual external doors), should not be 'cold to the touch'. Whilst most people will find a bare metal handle unpleasant to grip in the depths of winter, for some, particularly elderly people, it can be quite painful. Pull handle recommendations BS 800 horizontal pull handle BS 800:200 Door Opening Hardware BS 800 is more detailed in its recommendations, prescribing dimensional parameters for locks & latches, lever and pull handle furniture. Locks & latches To improve physical and visual access to the lever and lock keyway, the distance from the edge of the door and between the lever and keyway should be maximised; "..the cylinder should either be above the lever handle, or the minimum distance between the handle and the keyway.. should be 72mm." (BS 800 6.5..2) It also requires a backset of 54mm minimum (from edge of door to the lockcase operating centre see diagram opposite). Lever handles The principal requirements are that "where possible, door opening furnitue with a lever action should be used... without tightly grasping it or twisting the wrist e.g by using a closed fist".it also recommends levers return to the door face at the open end to aid the grip and avoid catching clothing. Dimensional characteristics for lever handles are covered by Fig. 7 of BS 800. See diagram opposite. Whilst lever handles are the preferred solution, there are circumstances where other issues can take precedence. The requirement to prevent self harm is one such issue where the risk associated with the lever furniture takes precedence over disabled access. Such situations will be covered by the provision of an Access Statement at the planning stage. Pull handles Recommendations are included concerning the positioning and size of pull handles min. length 600mm 900 00mm 000 preferred 400mm kicking plate 000mm 400mm Minimum diameter 9mm Projection from door face 45mm Mounting height for pull handles as shown opposite Recommendations also include the provision of a horizontal pull handle on doors fitted with a latch to enable wheelchair users to pull the door closed.see diagram opposite. Building Regulations in Scotland & Northern Ireland Technical Handbooks are published to guide specifiers in Scotland and Northern Ireland in much the same way as ADM but are not as detailed, offering little or no guidance in the specification of door hardware although the amended Technical Booklet (Part R) published in Northern Ireland does contain specific information related to handrailing and sanitary fittings. In most cases the Handbooks for Scotland refer specifiers to the guidance contained in BS 800. Grab rails Part M of Approved Document M of The Building Regulations covers the provision of sanitary facilities. Whilst not specifically part of the Orbis Commercial range, we have a full range of grab rails and disabled fittings. Please contact your Laidlaw Technical Consultant for further details. 40 www.laidlaw.net
DDA, APPROVED DOC. M & BS 800 Approved Document M (ADM) Continued Colour contrast & light reflectance For people with impaired vision the ability to identify key objects in the environment determines their ability to live independantly. It is a requirement of ADM that "all door opening furniture (on manually operated doors) contrasts visually with the surface of the door" (ADM 2.7). "All door furniture should contrast in colour and luminance with the surface of the door..." (BS 800 6.5.) The measure of brightness or luminance is measured by the amount of light which objects reflect (Light Reflectance Value LRV). Whilst people with impaired vision may not be able to easily identify colour they will generally be able to identify some reflected light. The greater the difference in LRV between the door and the hardware, ie the contrast between the two, the easier the hardware will be to locate. On a basic scale of 00, where a black object which reflects very little light has a LRV of typically less than 0, it is recommended that the door and hardware should have a contrast equivalent to a LRV difference of at least 5 points. Metallic finishes The suitability of metallic finishes is a complex issue due to numerous external factors which affect the percieved LRV of metallic substrates. The level and angle of incident light, the colour and nature of the door surface and the surrounding structure of walls, ceiling and floor will all have a bearing on the amount of light which each item of hardware reflects. It is therefore not possible to state which finishes are good and which are not; each must be judged in context to the surrounding environment. Recent Research The Research Group for Inclusive Environments was commissioned to undertake specific research in this area in association with the GAI (Guild of Architectural Ironmongers). A small (but nonetheless representative) group of visually impaired people tested actual ironmongery samples against various typical door finishes. Results showed that even at LRV differences of 0, over 72% of the test sample were confident of locating the hardware. It is thought that the D nature of the hardware, with its highlights and shadows contributes to the ease of location. Also, the nature of the hardware (gloss or matt) appeared to have no significant bearing on how easy it is to detect (see www.gai.org.uk for further information). Measurements Available to specifiers of Laidlaw products is a portable 'Spectrophotometer' which enables LRV readings to be taken of any material, for example door finishes and veneers, to compare with LRV readings of Laidlaw products. Please ask your Laidlaw Technical Consultant for more information. CPD seminars Laidlaw can provide a comprehensive series of RIBA approved CPD seminars including presentations covering DDA and Doc M issues. Subjects covered will include all aspects of colour contrast and demonstrations on the use of the 'Spectrophotometer'. CPD seminar at our Salford branch showing the use of the Spectrophotometer. 4 www.laidlaw.net
ORBIS COMMERCIAL INDEX 0 802. 2 0 802.2 2 0 80. 2 0 80.2 2 0 80. 2 0 804. 2 0 805. 2 0 806. 2 0 807. 2 0 808. 2 0 809. 2 0 80 2 0 82. 2 0 82.2 2 0 8. 2 0 8.2 2 0 8. 2 0 822. 2 0 822.2 2 0 822. 2 0 82. 2 0 82.2 2 0 82. 2 0 82. 2 0 82.2 2 0 82. 2 0 8. 2 0 8.2 2 0 8. 2 08 850 2 08 85 2 08 852 2 08 85 2 08 854 2 08 855 2 08 856 2 08 857 2 0 85 20 0 862 9 85 20 86 9 86 9 2 85 20 2 86 9 007 2 85 20 852 20 86 9 862 9 4 022 2 4 02 2 25 004 2 25 006 2 25 008 2 27 5 7 27 5. 7 27 5FMB 7 27 85 4 27 854 4 27 855 4 27 856 4 27 857 4 27 858 4 27 892.0 4 27 89.0 5 27 894.0 5 29 00 6 29 0 6 29 02 6 29 0 6 29 06 6 29 07 6 0 764 5 0 86 5 0 864 5 0 865 5 0 866 5 807 808 89 892 2 800. 25 2 800.2 25 2 80. 25 2 80.2 25 2 802 25 2 80 25 2 80. 8 2 8 25 2 85 25 2 840 25 2 845 25 2 850 25 4 005. 27 4 005.2 27 4 005. 27 4 006. 27 4 006.2 27 4 006. 27 4 007. 27 4 007.2 27 4 007. 27 4 00. 27 4 00.2 27 4 00. 27 4 0. 27 4 0.2 27 4 028 27 4 029.2 27 4 029.4 27 6 4 4 7 800. 8 7 800.2 8 7 80. 8 7 80.2 8 8 80. 8 7 80.2 8 7 879.5 8 7 879.6 8 50 800.0 8 50 800. 8 50 800..7 8 50 800.4 8 50 800.4.7 8 50 800.5 8 50 800.5.7 8 50 800.6 7 50 800.5 8 50 800.5.7 8 50 800CW 7 50 85.9.6 2 50 85.22.6 2 50 900.6 9 50 90.72 9 50 902.72 9 50 9.72 9 50 92.72 9 5 800.0 8 5 800. 8 5 800.2 8 5 800. 8 5 800.4 8 5 800.5 8 5 800.5 8 5 900.0 9 5 900. 9 5 900.4 9 5 900.5 9 5 900.5 9 5 90.72 9 52 80 2 52 802 2 52 80 2 52 804 2 52 805 2 52 806 2 5 89.5 5 89.8 5 89.24 5 89.0 5 89.45 5 89.60 5 822.8 5 822.24 5 822.0 5 822.45 5 822.60 5 82. 0 5 82.2 0 5 82.28 0 5 8.0 0 54 800.9 6 54 800.22 6 54 80.9 6 54 80.9FR 6 54 80.22 6 54 80.22FR 6 54 82.22 7 54 8.22 7 54 84.22 7 59 86 59 862 59 86 59 864 59 866 5 59 867 5 59 87 59 872 59 87 59 874 59 876 5 59 877 5 59 88 0 59 882 0 59 88 0 59 884 0 59 885 0 59 889 0 60 00. 22 60 00.2 22 60 00. 22 60 00.4 22 60 00.7 22 60 0. 2 60 02. 2 60 0. 2 60 04. 2 60 04.2 2 60 00 24 60 0 24 60 02 24 60 0 24 60 04 24 60 05 24 60 06 24 60 07 24 60 08 24 60 09 24 60 040 24 60 04 24 60 042 24 60 04 24 60 044 24 60 045 24 60 047 24 60 048 24 60 05 2 60 052. 2 60 052.2 2 60 054 2 60 055 2 60 056 2 60 060 2 60 062 2 60 06 2 60 070 2 60 07 2 60 072 2 60 07 2 60 45. 24 60 45.2 24 60 46. 24 60 46.2 24 60 4. 2 60 4.2 2 60 42. 2 60 42.2 2 60 4. 2 60 4.2 2 60 44. 2 60 44.2 2 60 45. 2 60 45.2 2 60 46. 2 60 46.2 2 60 47. 2 60 47.2 2 60 48. 2 60 48.2 2 60 60 22 60 602 22 60 60 22 60 604 22 60 605 22 60 606 22 60 607 22 60 608 22 60 609 22 60 67 22 60 68 22 60 69 22 60 620 22 60 62 22 60 622 22 60 62 22 60 624 22 6 800 26 62 800.0 26 62 800. 26 62 800.2 26 62 800. 26 62 800.8 26 80 802 26 8 80 26 8 802 26 8 80 26 8 804 26 89 00 26 APH.0 APH.02 FPP 2 FPP2 2 FPP 2 FPP5 2 FPP6 2 FPP7 2 IP H 8 IP H2 8 IP L 9 IP L4 9 42 www.laidlaw.net
architectural ironmongery doorset solutions handrail & balustrading 2 4 access control 2 4 5 technical helpline 0845 0700 970 technical@laidlaw.net Laidlaw is the leading specifier, distributor and technical service provider for architectural ironmongery, doorsets, handrail & balustrading and access control solutions to the construction industry. Laidlaw offers its unique service through a national network of Sales Centres, supported by a centralised distribution centre at Willenhall which has the capacity to pack and despatch individual items or by doorset. Barnstaple Unit, Brannam Crescent Roundswell Business Park (West) Barnstaple, North Devon EX TD T: 027 920 F: 027 929 Bristol Unit 4, Marketside Industrial Estate Albert Road, St. Philips Bristol BS2 0XS T: 07 00 980 F: 07 980 058 Cardiff Unit A2 Cook Court Pacific Business Park Cardiff CF24 5AB T: 029 2047 808 F: 029 2049 0250 Gateshead Unit Halifax Court, Halifax Road Dunston, Gateshead Tyne & Wear NE 9JT T: 09 46 400 F: 09 46 40 Glasgow 4 Clifford Court 7 Woodville Street Ibrox Business Park Glasgow G5 2RQ T: 04 445 8892 F: 04 445 887 Kinmel Bay Unit 7 Tir Llwyd Industrial Estate St Asaph Avenue Kinmel Bay, Rhyl North Wales LL8 5JA T: 0745 25 F: 0745 249 Laidlaw Gulf LLC PO Box 85292 Dubai United Arab Emirates T: +97 (0) 4885 7404 F: +97 (0) 4885 744 Liverpool 5 Century Building Summers Road Brunswick Business Park Liverpool, Merseyside L 4BL T: 05 709 948 F: 05 709 9455 London The Building Centre 26 Store Street London WCE 7BT T: 0207 46 0779 F: 0207 46 0740 Perth PO Box 5 Arran Road Perth PH DU T: 078 62058 F: 078 6262 Salford Centurion House Dakota Avenue, Salford Manchester M50 2PU T: 06 848 00 F: 06 872 9 Sheffield Unit 7 Riverside Court Don Road Sheffield S9 2TJ T: 04 24 896 F: 04 242 659 Willenhall Strawberry Lane Willenhall West Midlands WV RS T: 0902 600400 F: 0902 600490 York Saturn Architectural Solutions Ltd Unit 9 Harrier Court Airfield Business Park Elvington, York YO4 4EA T:0904 608864 F: 0904 607759 Sales Centre Trade Counter Distribution Centre Architectural Ironmongery Solutions Laidlaw's comprehensive portfolio of architectural ironmongery, featuring the renowned Orbis brand, is designed to meet or exceed the highest levels of aesthetic and performance standards for today's construction industry. Doorset Solutions Laidlaw has pioneered the Orbis Doorsets solution which is supplied complete with the door, frame, architraves and factory fitted ironmongery to maximise efficiency and minimise onsite work. Handrail and Balustrade Solutions Laidlaw's handrail and balustrade solutions are available in a wide variety of construction and finish options. From site surveys and design through to supply and installation, our fully trained staff offer a comprehensive technical service at all stages. Access Solutions From simple masterkeyed cylinders up to stateoftheart biometric access control and automatics, we have the expertise to design and supply an integrated system to suit each specific building and application. While Laidlaw has taken every care to ensure the accuracy of information, data and advice contained in this literature, no liability in respect of such information whether given negligently or not can be accepted by the company. Due to variations in the printing process, actual colours may differ from those shown. Laidlaw retains the right to amend the technical specification of any range of equipment shown. To email a UK sales centre use the following format: info.location@laidlaw.net (e.g. info.bristol@laidlaw.net) As part of continual efforts to reduce our carbon footprint, this brochure is printed on a FSC certified paper stock which originates from wellmanaged forests, controlled sources and recycled wood or fibre as indicated by the logo opposite. EMS 5228 RS 0508 HA CONTRACTORS HEALTH & SAFETY ASSESSMENT SCHEME Chas Accredited Incorporating DSMA & ABHM Laidlaw Solutions Limited July 20/L08/002