Revised! see Protective Earthing Addendum Installation Guide J2 O O J1 4 IN 3 RELAY OUTPUTS EXPANSION 2 J3 1 O O Relays: A 4 way Relay Module provides four 1 Amp single pole Relays with connection terminals to the Common (C), Normally Open (NO), and Normally Closed (NC) contacts. If fitted to an 8-32 input DGP two relay modules can be connected together in daisy-chain fashion to provide up to 7 relays on TS0020 to TS0024 DGPs or up to 8 relays on TS0820 to TS0824 DGPs. When fitted to a TS0015 (V6.0Y or later) Challenger Alarm Panel, the relay module provides 3 relays. Relays 1, 3 and 4 can be used. Relay 2 is not used, as the Strobe output on the Panel follows relay 2. When fitted to a TS0816 (Version 8 or later) Challenger Alarm Panel, the relay module provides 4 relays. Dimensions ( PCB Card ) Size B PCB: 80 x 52 mm Current Consumption: The 4 way Relay card draws no current on standby, and a total of 100mA with all 4 relays active. Version 8. 4 Way Relay Card - Model : Issue I, Revision I: August 1994 1
Wiring: Interconnection between the Relay module and the different Challenger equipment is detailed below. Version 8. Challenger Alarm Panel. TS0816 or Version 8. 8 Input Data Gathering Panel. TS0820, TS0822, TS0823, TS0824 Cable: LEV8-10-500P (Supplied with ) 4 Way Relay module J2 Version 8 Panel J14 OR 8 I/P DGP J8 (O/P) 1 +12 Volts 1 2 Relay 1 2 3 Relay 2 3 4 Relay 3 4 5 Relay 4 5 6 Relay 5 6 (Not used on TS0816 Alarm Panel) 7 Relay 6 7 (Not used on TS0816 Alarm Panel) 8 Relay 7 8 (Not used on TS0816 Alarm Panel) 9 Relay 8 9 (Not used on TS0816 Alarm Panel) 10 0V 10 Version 6 Challenger Alarm Panel. TS0015 Cable: LETS0043 ( Ordered separately) 4 Way Relay Module J2 V6 Chall Panel J8 2 Relay 1 7 4 Relay 3 6 5 Relay 4 5 1 +12 Volts 2 8 Input Data Gathering Panel. TS0020, TS0022, TS0023, TS0024 Cable: LETS0040 ( Ordered separately) 4 Way Relay module J2 8 I/P DGP J7 (O/P) 1 +12 Volts 1 2 Relay 1 2 3 Relay 2 3 4 Relay 3 4 5 Relay 4 5 6 Relay 5 6 7 Relay 6 7 8 Relay 7 8 Interconnection between two modules. Cable: LEV8-10-500P ( Supplied with ) 4 Way Relay module J2 4 Way Relay module J3 - Expansion 1 +12 Volts 1 2 Relay 5 2 3 Relay 6 3 4 Relay 7 4 5 Relay 8 5 6 Not Used 6 7 Not Used 7 8 Not Used 8 9 Not Used 9 10 0V 10 2 IN.P65: Issue I, Revision I: August 1994
Mounting: TS0816: TS0015: DGP 8-32: TS0304: The has to be mounted in a separate enclosure and is connected with the cable supplied. The has to be mounted in a separate enclosure and a special cable (LETS0043) must be used. The is mounted on existing standoffs in the DGP enclosures and connected to the TS082x DGP PCB with the cable supplied. If connecting to a TS002x DGP a special cable (LETS0040) must be used. (Where 'x' is TS0820, TS0822, TS0823 or TS0824.) Separate Enclosure. V6 DGP Box 360 x 260 x 75mm with mounting for 1 Size "A" PCB, and 4 Size "B" PCBs or 2 Size "Double B" PCBs. Note: The is a Size "B" PCB. ( See table below ) Maximum 4 Way Relay Cards per Challenger product. Maximum Cards. Maximum Usable Relays. TS0816 V8: 1 4 TS0820/TS0822 V8: 2 8 TS0015 V6 / V7: 1 3 TS0020/TS0022: 2 7 Installation Summary: CAN CONNECT TO CABLE INSTALLATION TS0816 V8 Alarm Panel. TS0820/TS0822 V8 DGPs. interconnection. Cable supplied Cable supplied Cable supplied Separate enclosure required. Up to 2 s can be fitted in TS082x enclosure depending on what other cards are fitted. TS0015 Alarm Panel (V6 / V7). TS0020/TS0022 8 I/P DGP. LETS0043-1M LETS0040-260P Separate enclosure required. Up to 2 s can be fitted in TS002x enclosure depending on what other cards fitted. Note: Clocked Relay/Open Collector Cards and 4 Way Relay Cards cannot be used together on the same product. Version 8. 4 Way Relay Card - Model : Issue I, Revision I: August 1994 3
Enabling and Programming: Program Relay Assignments. Refer to the Challenger Programming guide section on Numbering to determine system relay numbers. Map relay numbers to Event numbers and/or timezones as required. Relay function can also be inverted or programmed to be active or inactive during the timezone. If connected to the Challenger Panel, "Number of Relay Controllers" in Installer menu Option 7 must be set to 0. Connection Diagrams: Challenger Panel PANEL TS0015/TS0816 Cable. See table on previous page. J2 EXP. 8 Input DGP 8 I/P DGP Cable. See table on previous page. J2 J2 EXP. EXP. LEV8-10-500P (Supplied) 4 IN.P65: Issue I, Revision I: August 1994
N4131 Please note, this product conforms to the standards set by Standards Australia on behalf of the Australian Telecommunications Authority (AUSTEL) and the Spectrum Management Agency (SMA). WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. The Challenger is designed and manufactured by: Interlogix Australia Pty Ltd 646 Whitehorse Rd MITCHAM VIC 3132 A.B.N. 84 086 771 404 PH: 03 9259 4700 FX: 03 9259 4799 C Interlogix Australia 2001 Version 8. 4 Way Relay Card - Model : Issue I, Revision I: August 1994 5