Specialist Tools and Accessories

Specialist Tools and Accessories 1.5T Crimpers C343 3T Crimpers C343 5T Crimpers C343 12 to 15T Crimpers and Crimp Heads C344 23 to 25T Crimpers and Crimp Heads C347 52 to 60T Crimpers and Crimp Heads C347 Batteries and Accessories C348 Cutters and Cutting Heads C349 Electric and Hydraulic Pumps C352 Hydraulic Punch Tool and Accessories C353 Dies Copper C355 Dies Earthing Copper C357 Dies Indent Crimp C358 Dies Aluminium C359 Dies Aluminium Nest Crimp C360 Dies Cutting C361 Dies Insulink C361 Adaptors C361 Hydraulic Pole Saws C362

18V CEMBRE CRIMPING AND CUTTING TOOLS The Cembre range of 18V battery powered hydraulic tools are loaded with features. Based of the renowned Cembre 14V battery range of 13 ton tools, this range is suitable for crimping up to 400mm 2 and cutting electrical cable up to 95mm in diameter. The new 18V 4.0 Ah lithium-ion battery offers a higher capacity than its predecessor the 14.4V 3 Ah. Greater crimping speed and crimping force is the result of a revitalised hydraulic system with double speed action, a more rapid approach of the dies or cutting blade to the connector or conductor and improved speed and control of the crimping/cutting action. A maximum pressure sensor and security valve assures greater precision and repeatability of the pressure cycle with double the provision for operator safety. Crimping tools incorporate on-board memory for data logging up to 200 000 cycles which can be transferred to a PC by USB interface. This unique feature assists with logging work performance and ensuring the tool is in proper working condition. CRIMPING TOOLS The crimping tools are supplied with OLED display, which provide essential real time tool operating information such as momentary force reached and maximum pre-set level (in Newtons, tons, PSI or bar). The OLED also displays the battery charge level, tool serial number, number of cycles performed and number of cycles before scheduled maintenance. An LED work light and service status light is displayed for assistance with maintenance. The Cembre 18V range is easy to manage during crimping with low operating noise and vibration aiding user comfort in addition to the ergonomic housing. A LED light is included for convenience and safety, enhancing vision in darker areas. FEATURES: Simple and basic operation with low vibration and noise in addition to comfortable handling 18V 4.0 Ah power system provides a 20-30% improvement in cycle time and a 70-95% increase in the number of cycles OLED display provides real time operating information USB interface and on-board memory provides convenient logging Heads rotate at various angles Built in LED working light for dark areas Battery charger and spare battery in kit CUTTING TOOLS The Cembre 18V range is easy to manage during crimping with low operating noise and vibration aiding user comfort in addition to the ergonomic housing. An LED light is included for convenience and safety, enhancing vision in darker areas. The blades are manufactured from special high strength steel, ensuring long service life. The head rotates, adapting to the angle that the conductor is cut, especially in a confined space. FEATURES: Simple and basic operation with low vibration and noise in addition to comfortable handling 18V 4.0 Ah power system provides a 20-30% improvement in cycle time and a 70-95% increase in the number of cycles power by one Head rotates at various angles (please see table) Built in LED working light for dark areas Battery charger and spare battery in kit 18V 4.0 AH BATTERY Provides 100% of its energy between -15 C and 50 C Electronic control of single cells to avoid over and under charging Air-cooled charging technology to increase battery life Auto-off to optimise energy consumption Built in LED charge level indicator Tough and rugged housing C342

1.5T CRIMPERS CRIMPERS 1.5T 1.5T BATTERY CRIMPER 18V 3T CRIMPERS CRIMPERS 3T 3.5T BATTERY CRIMPER 18V 5T CRIMPERS HYDRAULIC CRIMPERS 5T 5 TONNE HYDRAULIC CRIMPER SPECIALIST TOOLS AND ACCESSORIES Part No. B15MDT Lightweight terminal crimper with a 1.5 tonne crimp capability One hand operation with a head rotation of 340 degrees Includes a moulded carry case with two batteries and a charger Suitable for Copper terminals, lugs and splices up to 16 sq.mm Requires suitable dies for pre or uninsulated bootlace ferrules Part No. B35-50MDT Lightweight terminal crimper with a 3.5 tonne crimp capability One hand operation with a head rotation of 180 degrees Includes a moulded carry case with two batteries and a charger Suited for Australian dimension Copper or Aluminium lugs or links Uses standard M type (5 ton) dies up to 95mm2 Part No. HT51 Designed for the overhead linesman - this crimper is lightweight and can be operated with one hand Small enough to be carried in a tool pouch Only three pumping operations required to complete crimp BATTERY CRIMPERS 5T 5T BATTERY POWERED CRIMPER LI-ION Part No. B500T 18V battery powered 5 tonne, hydraulic crimping tool giving greater crimping speed and more operations Improved handling balance with low noise and vibration Dies available for Copper lugs from 6 to 120 sq.mm LCD condition indication displays crimping pressure Data storage logging of crimping operations PNEUMATIC CRIMPERS 5T PNEUMATIC TERMINAL & LUG CRIMPER 5 TONNE Part No. PA-6B Pneumatic crimping head for electrical terminals, designed for flexible product operations Large range of dies and replacement head/jaws available Operated by foot air valve Unit should be bench mounted using the attachment base PNEUMATIC CRIMPING HEAD Part No. PA-6BHD Heavy Duty Pneumatic Terminal and Lug Crimper for flexible product operations Machine jaws and a large range of dies also available Operated by foot valve Unit should be bench mounted using attachment C343

PNEUMATIC CRIMPING MACHINE JAWS PA-6B Part No. Y-PA6B JAWS Spare part for PA-6B Pneumatic Terminal and Lug Crimper 12 TO 15T CRIMPERS AND CRIMP HEADS BATTERY CRIMPERS 13T 13T BATTERY CRIMPER LI-ION Part No. B1350-CT 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a quicker pace Balanced, low noise and vibration for better operator comfort LCD condition display monitors the crimp pressure Data logging of crimping cycles Copper dies available up to 400mm2 13T BATTERY CRIMPER LI-ION-LONG HEAD Part No. B1350L-CT 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a quicker pace Balanced, low noise and vibration for better operator comfort LCD condition display monitors the crimp pressure Data logging of crimping cycles Copper dies available up to 400mm2 13T BATTERY CRIMPER LI-ION U HEAD Part No. B1350-UCT 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a quicker pace Balanced, low noise and vibration for better operator comfort LCD condition display monitors the crimp pressure Data logging of crimping cycles Copper dies available up to 400mm2 13T BATTERY CRIMPER LI-ION Part No. B1300-CT 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a quicker pace Balanced, low noise and vibration for better operator comfort LCD condition display monitors the crimp pressure Data logging of crimping cycles Copper dies available up to 400mm2 13T BATTERY CRIMPER LI-ION-LONG HEAD Part No. B1300L-CT 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a quicker pace Balanced, low noise and vibration for better operator comfort LCD condition display monitors the crimp pressure Data logging of crimping cycles Copper dies available up to 400mm2 C344

HYDRAULIC CRIMPERS 13T 13 TONNE HYDRAULIC CRIMPER WITH C HEAD Part No. HT131-C Quality manufacture and robust design will give years of trouble free service 25mm throat opening Two speed - saving time and effort during crimping Head rotates 180 degrees for work in tight spaces HT131-C WITH FULL SET OF DIES 16-300MM2 Part No. HT131-C-WHO Quality manufacture and robust design will give years of trouble free service 25mm throat opening Two speed - saving time and effort during crimping Head rotates 180 degrees for work in tight spaces 13 TONNE U HEAD HYD. CRIMPER Part No. HT131-UC Easy access to tight cable joints, particularly in a trench Shorter handles ensure easier handling Large throat opening Supplied in a heavy-duty plastic carry case HT131-UC WITH FULL SET OF DIES 16-300MM2 Part No. HT131-UC-WHO Easy access to tight cable joints, particularly in a trench Shorter handles ensure easier handling Large throat opening Supplied in a heavy-duty plastic carry case HT131L-C WITH FULL SET OF DIES 16-300MM2 Part No. HT131L-C-WHO Quality manufacture and robust design will give years of trouble free service Nominal force of 13.3 tonnes at the die faces Head rotates 180 degrees for work in tight spaces Flexible and easy handling 13 TONNE C LONG HEAD HYD. CRIMPER Part No. HT131LN-C Quality manufacture and robust design will give years of trouble free service Head rotates 180 degrees for work in tight spaces Two speed - saving time and effort during crimping Supplied in a heavy-duty plastic carry case C345

CRIMPER ACCESSORIES 13T HT131-C STORAGE CASE HT131UC HT131L-C Part No. Y-HT131-CASE Spare case only Case suits HT131 series hydraulic tools Features compartments for dies and crimping tool Colour: Cembre Blue C DIE ADAPTOR FOR RHU/UC Part No. AU130-C Removable die holder for RHU131-C crimp head and HT131-UC crimp tool Replacement part for holding Cembre 13 tonne C type dies Fits tool head and locked with pin CRIMP HEADS 13T 13 TONNE REMOTE HEAD C TYPE 25MM THROAT Part No. RHC131 Remote head 13 tonne crimper to be used with a CABAC remote pump or any pump developing 700 bar (10,000 psi) pressure Use with standard CABAC 12 tonne dies Standard C throat and wide throat available Not supplied with a case 13 TONNE REMOTE HEAD U TYPE Part No. RHU131-C Remote head 13 tonne crimper to be used with a CABAC remote pump or any pump developing 700 bar (10,000 psi) pressure Steel case for head and dies available (Part No. Y-RHC131 CASE) Throat opening: 34mm Weight: 3.7kg 13 TONNE REMOTE LONG HEAD C TYPE 42MM Part No. RHC131L-N Remote head 13 tonne crimper to be used with a CABAC remote pump or any pump developing 700 bar (10,000 psi) pressure Use with standard CABAC 12 tonne dies Standard C throat and wide throat available Not supplied with a case CRIMPERS 12T ECONOMY 12T HYDRAULIC CRIMPER C HEAD Part No. CYO-510B Economically priced 12 tonne tool with a two stage pumping action for reduced crimping time 180 degree head rotation for work in tight spaces Reinforced glass fibre handles Supplied in a heavy-duty plastic carry case C346

23 TO 25T CRIMPERS AND CRIMP HEADS CRIMP HEADS 23T 23 TONNE CRIMPER - REMOTE HEAD SPECIALIST TOOLS AND ACCESSORIES Part No. ECW-H3D 23 tonnes of force at the die face with the ability to crimp up to 630mm2 Copper and 500mm2 Aluminium Light-weight - easily handled by one person Couple with a CABAC hydraulic pump (700 bar) Steel storage case supplied separately ECW-H3D STEEL STORAGE CASE Part No. Y-ECW-3D CASE For use with the 23 tonne Hydraulic Crimper (Part No. ECW-H3D) Die holder tray is also available ECW-3D DIE HOLDER TRAY ONLY Part No. Y-ECW-3D D/HOLD For use with the 23 tonne Hydraulic Crimper (Part No. ECW-H3D) Steel storage case is also available 52 TO 60T CRIMPERS AND CRIMP HEADS CRIMP HEADS 52T HYD. PRESSHEAD WITH FEMALE COUPLER Part No. RHU520 Remote head 52 tonne crimper can be used with one of our hydraulic pumps or any pump developing 700 bar (10,000 psi) pressure Crimps Cu and Al lugs and compression fittings up to 1200mm2 Throat opening: 75mm Weight: 18kg CRIMPING HEAD 60T HYDRAULIC CRIMPING HEAD 600KN Part No. RHU600 Remote head 60 tonne can be used with hydraulic pumps developing 700bar (10,000psi) Manufactured in thermally treated steel Resistant to oxidation from external agents, abrasion and wear Equipped with a quick fit hydraulic male coupler Precision made for greater safety and reliability C347

HYDRAULIC CUTTING UNIT Part No. CP1120-W-1000-KV Cutter head and pump system to safely cut LV and MV cable in a network if the cable has not been spiked The cutter head is insulated from the pump System must be rebuilt if a live cable is cut Earth connection available to ground/earth the head and the pump Supplied in a metal case BATTERIES AND ACCESSORIES BATTERIES AND ACCESSORIES B131-C VEHICLE BATTERY CORD 6M WITH PLUG Part No. Y-ESC600 Vehicle battery cord for the 13 tonne battery powered hydraulic crimper Suitable for B131-C and B131LN-C parts Length: 6M BATTERY CRIMPER 13T CAR CHARGER B131-C Part No. B131-C CARCHARGER 12V cigarette lighter charger cord for the 13 tonne battery powered hydraulic crimper Suitable for B131-C and B131LN-C parts CHARGER TO SUIT CB1430H BATTERY Part No. DC1414 240V charger for the 13 tonne battery powered hydraulic crimper Suitable for B131-C and B131LN-C parts NI-MH 14.4V 3.0AH RECHARGEABLE BATTERY Part No. CB1430H Compatible with select range of Cembre crimpers Battery material: Ni-MH Battery voltage: 14.4V Battery current: 3 Ah LI-ION 18V 4.0AH RECHARGEABLE BATTERY Part No. CB1840L Electronic control of single cells to avoid overcharging and undercharging Air-cooled charging technology to increase battery life Auto-off to optimise energy consumption Battery charger also available (Part No. ASC30-36) C348

CHARGER TO SUIT CB1840L BATTERY Part No. ASC30-36 Battery charger for use with the Li-Ion 18V 4.0 Ah Rechargeable Battery (Part No. CB1840L) CUTTERS AND CUTTING HEADS CUTTERS REMOTE HYD.ST.WIRE ASCR 40MM OD Part No. TC04 Remote hydraulic cutter head specifically designed to cut ACSR, Copper conductors/cables and steel ropes, Copper, Aluminium and steel rods Double stage hydraulic system saves time for the operator Fits any pump with Quick Connect hydraulic fittings Supplied in a steel case HYD. CUT TOOL HEAD CU/AL 55MM ACSR 50MM Part No. TC055 Equipped with a quick automatic coupling for connection to Cembre hydraulic pumps with a working pressure of 700bar Designed to cut cables, steel rope, rods, armoured cable Supplied in a metal case See data sheet for cutting specifications PUMP OPERATED CUTTER HEAD MAX DIA 85MM Part No. TC085 Remote hydraulic cable cutter head specifically designed to cut annealed Copper and Aluminium conductors and telecom cables Supplied with a steel case Not suitable to cut steel and armoured cable Maximum cutting diameter: 85mm PUMP OPERATED CUTTER HEAD MAX DIA 95MM Part No. TC096 Remote hydraulic cable cutter head specifically designed to cut annealed Copper and Aluminium conductors and telecom cables Supplied with a steel case Not suitable for armoured cable Maximum cutting diameter: 95mm PUMP OPERATED CUTTER HEAD MAX DIA 120MM Part No. TC120 Remote hydraulic cable cutter head specifically designed to cut annealed Copper and Aluminium conductors and telecom cables Supplied with a steel case Automatic safety valve to prevent over-pressure Complete with 3/8 inch NPT self-lock male coupler Not suitable to cut steel and armoured cable C349

HYD. CUTTING TOOL ACSR/STEEL 24MM MAX OD Part No. HT-TC026 Hand operated hydraulic tool specifically designed to cut ACSR, Copper conductors/cables and steel ropes, Copper, Aluminium and steel rods Dual speed pump Head can rotate 90 degrees Supplied with a canvas bag Maximum cutting diameter: 24mm HYD. CUTTING TOOL CU/AL 55MM MAX OD Part No. HT-TC055 Hand operated hydraulic cable cutter specifically designed to cut steel and wire rope Produces up to 140kN force at the max pressure of 808 bar Suitable for Cu, Al, armoured cable, steel rope and rods See data sheets for cutting specifications Maximum cutting diameter: 55mm HYD. CUTTING TOOL AL/CU 65MM MAX OD Part No. HT-TC065 Hand operated hydraulic cable cutter specifically designed to cut Copper, Aluminium and telecom cables Supplied in a canvas bag Not suitable to cut steel and armoured cable Maximum cutting diameter: 65mm HYD. CUTTING TOOL CU/AL 85MM MAX OD Part No. HT-TC0851 Hand operated hydraulic cable cutter specifically designed to cut annealed Copper and Aluminium conductors and telecom cables Double stage hydraulic system saves time for the operator Head can rotate 180 degrees Supplied with a canvas bag Maximum cutting diameter: 85mm 18V BATTERY CUTTER 25MM Part No. BTC250T Battery powered cutter suitable for ACSR, steel rope, stay wire, steel rods and armoured cable 18V battery produces faster and more cutting operations Head pivots up to 180 degrees - ease of use in confined spaces Low noise and minimal vibration aid operator comfort Lightweight and balanced for single handed operation 18V BATTERY CUTTER 50MM Part No. BTC500T Battery powered 18V cable cutter for Copper, Aluminium and telecom cables and conductors Blades: High strength, heat treated special steel Head pivots up to 90 degrees - ease of use in confined spaces Low noise and minimal vibration aid operator comfort Lightweight and balanced for single handed operation C350

18V BATTERY CUTTER 55MM Part No. BTC550T 18V battery powered for faster cutting operations. Lightweight and balanced for single handed operation Cutting blades: High strength, heat treated special steel Head pivots up to 320 degrees - ease of use in confined spaces Low noise and minimal vibration aid operator comfort Cutter suitable for armoured cable, steel rope and rods 18V BATTERY CUTTER 65MM Part No. BTC650T 18V battery powered for faster cutting operations for Aluminium, Copper and telecom cables Cutting blades: High strength, heat treated special steel Head pivots up to 335 degrees - ease of use in confined spaces Low noise and minimal vibration aid operator comfort Lightweight and balanced for single handed operation 18V BATTERY CUTTER 95MM Part No. BTC950T 18V battery powered for faster cutting operations for Aluminium, Copper and telecom cables Cutting blades: High strength, heat treated special steel Head pivots up to 335 degrees - ease of use in confined spaces Low noise and minimal vibration aid operator comfort Lightweight and balanced for single handed operation C351

CUTTERS HYDRAULIC CUTTER - ECONOMY MAX 240MM2 Part No. CPC-30A Economically priced - designed to cut cable with a shearing scissor action Self contained hydraulic hand pump develops 6.7 tonnes Head swivels for access into tight situations Hardened steel blades specifically to cut ACSR Easy to use - designed to attach to a hand held electrical drill Various cutting sizes available from 30-100mm diameter cable Supplied in an easy to carry case Blade can be sharpened using a file or mini grinder Part No. Description Unit Qty DDQ33 CUTTER HEAD DIA. 22 MM STEEL ROPE EA 1 DDQ30 CUTTER HEAD DIA. 30 MM ACSR CHAIN EA 1 DDQ80 CUTTER HEAD DIA. 80 MM AL/CU CABLE EA 1 HYD. STEEL AND WIRE ROPE CUTTER 40MM MAX Part No. MSS-S40-M Smallest and most powerful cutter weight to power ratio available on the market today 2 speed hydraulic pumping for rapid advance and cutting BATTERY POWERED CABLE CUTTER 40MM MAX Part No. MSS-S40-18V Guillotine style for cutting Copper, Aluminium, ACSR and Steel Wire Rope up to 40mm O.D. Rapid blade advance - double speed in cutting stage Rotating head 180 degrees Factory pre-set overload relief to protect tool ELECTRIC AND HYDRAULIC PUMPS PUMPS HYD. FOOT PUMP 2 STAGE IN CASE Part No. PO7000 Double stage foot pump for faster crimping and cutting Hands are free for cable and lug positioning Maximum stability with an extra large base Supplied in a robust steel case BATTERY POWERED HYDRAULIC PUMP Part No. B70M-P24 A state of the art unit designed for mobile crimping and cutting - use with any of the CABAC crimping heads and cutters Light-weight and balanced - easy to carry Powerful 24V battery with a 60 minute recharge Manual pressure relief valve C352

CRIMPING PUMP -0.45KW-240V- 12V REMOTE Part No. MSS-HCP-45SV Suitable for use with all hydraulic remote crimping heads up to 60 tonne capacity Light-weight, portable and small in size with high power Audible POP signals completion of the crimp cycle Comes with remote control pendant Double Acting pump available (Part No. MSS-HCP-45SV-DA) ELECTRIC HYDRAULIC PUMP-240V Part No. KSMP-3AR Usable oil: 1.8 litres First stage pressure: 15 bar at 2.0 l/min Second stage pressure: 700 bar at 0.2 l/min Power: 240V, 1.6A SUPER LIGHTWEIGHT 240V ELECTRIC PUMP Part No. HPP1 This pump is called the Peanut Pump for good reason. Small and light-weight, this pump produces a full 700bar (10,000 psi) pressure Sufficient oil volume to power all CABAC crimp heads and cutters Operate at any angle - no leaks if tipped over Motor and pump are totally enclosed and drip proof Comes with a 3m hose and coupler to suit Cabac and MSP hyd. tools HYDRAULIC PUMP/HOSE 240V LIGHTWEIGHT Part No. HPP2 Two stage pumping with 2.5L/min flow in low pressure stage and 0.35L/min in the high pressure stage For CABAC and MSS remote crimp heads (up to 60 tonnes) and cutters Power Supply Voltage: 240V/50Hz Weight: 18kg Comes with a 3m hose and coupler to suit Cabac and MSP hyd. tools HYDRAULIC PUNCH TOOL AND ACCESSORIES HYDRAULIC PUNCH DIE 15T 15 TONNE HYDRAULIC PUNCH DIE SET Part No. SKP-15 A complete punch tool set including a pump and various dies for mild steel <3.2mm Output of 15 tonnes and a ram stroke of 25mm Round dies: dia. 22, 27.6, 34.1, 42.7, 48.7 and 60.5mm Square die: 32x32mm Additional dies and spindles also available separately PUNCH DIE SQUARE 32 X 32MM W/SPINDLE Part No. PDS32 Die for SKP-15 hydraulic punch tool set Suitable for mild steel up 3.2mm thick Die is not suitable for stainless steel Round and square dies available for SKP-15 C353

PUNCH DIE SET SPINDLE Part No. PDSPINDLE Spare part for the SKP-15 15 tonne Hydraulic Punch A compact, light and fast punching tool Full kit also available PUNCH DIE SET SPACER Part No. PDSPACER Spare part for the SKP-15 15 tonne Hydraulic Punch A compact, light and fast punching tool Full kit also available HYDRAULIC PUNCH DIE ACCESSORIES Die for SKP-15 hydraulic punch tool set Suitable for mild steel up 3.2mm thick Die not suitable for stainless steel Round and square dies available for SKP-15 Part No. Description Unit Qty PD16.2 PUNCH DIE ROUND 16.2MM EA 1 PD20.4 PUNCH DIE ROUND 20.4MM EA 1 PD22.5 PUNCH DIE ROUND 22.5MM EA 1 PD25.4 PUNCH DIE ROUND 25.4MM EA 1 PD32.5 PUNCH DIE ROUND 32.5MM EA 1 PD40.5 PUNCH DIE ROUND 40.5MM EA 1 PD50.8 PUNCH DIE ROUND 50.8MM EA 1 PD60.5 PUNCH DIE ROUND 60.5MM EA 1 PD63.5 PUNCH DIE ROUND 63.5MM EA 1 PD88.9 PUNCH DIE ROUND 88.9MM EA 1 PD115.5 PUNCH DIE ROUND 115.5MM EA 1 C354

DIES COPPER COPPER DIES 5T SPECIALIST TOOLS AND ACCESSORIES Dies to suit 5 tonne crimping tool for Australian and New Zealand dimensioned Copper lugs and links Hexagonal crimp dies Part No. Description Nominal Conductor A/F Hex Die Unit Qty (mm 2 ) (mm) M44-50 HT50 HEX COPPER DIE 6MM2 6 4.4 EA 1 M57-50 HT50 HEX COPPER DIE 10MM2 10 5.7 EA 1 M63-50 HT51 HEX COPPER DIE 16MM2 16 6.3 EA 1 M77-50 HT51 HEX COPPER DIE 25MM2 25 7.7 EA 1 M82-50 HT51 HEX COPPER DIE 6MM2 6 8.2 EA 1 M92-50 HT51 HEX COPPER DIE 35MM2 32 9.2 EA 1 M96-50 HT51 HEX COPPER DIE 25MM2 25 9.6 EA 1 M104-50 HT50 HEX COPPER DIE 50MM2 50 10.4 EA 1 M115-50 HT51 HEX COPPER DIE 70MM2 70 11.5 EA 1 M142-50 HT51 HEX COPPER DIE 95MM2 95 14.2 EA 1 M148-50 HT51 HEX COPPER DIE 70MM2 70 14.8 EA 1 M165-50 HT50 HEX COPPER DIE 120MM2 120 16.5 EA 1 M183-50 HT51 HEX COPPER DIE 150MM2 150 18.3 EA 1 M190-50 HT51 HEX COPPER DIE 95MM2 95 19.0 EA 1 M200-50 HT50 HEX COPPER DIE 185MM2 185 20.0 EA 1 COPPER B035 DIES Custom dies for B035 3.5 ton crimping tool Hexagonal dies for Copper lugs and links Range suitable from 6mm2 to 120mm2 Die fits Klauke EK354-L crimp tool Part No. Description Unit Qty B035-6 DIE B035 CU 6MM EA 1 B035-10 DIE B035 CU 10MM EA 1 B035-16 DIE B035 CU 16MM EA 1 B035-25 DIE B035 CU 25MM EA 1 B035-35 DIE B035 CU 35MM EA 1 B035-50 DIE B035 CU 50MM EA 1 B035-70 DIE B035 CU 70MM EA 1 B035-95 DIE B035 CU 95MM EA 1 B035-120 DIE B035 CU 120MM EA 1 C355

COPPER DIES 12/13T Crimping dies for Australian and New Zealand dimensioned lugs and links Hexagonal dies for Copper lugs and links For 12/13 tonne hydraulic crimp tools Carbon steel dies Part No. Description Conductor Range A/F Hex Die Unit Qty (mm 2 ) HT130-C-6 COPPER HEXAGONAL DIE 6MM2 6 4.4 EA 1 HT130-C-10 COPPER HEXAGONAL DIE 10MM2 6 4.4 EA 1 HT130-C-16 COPPER HEXAGONAL DIE 16MM2 16 6.3 EA 1 HT130-C-25 COPPER HEXAGONAL DIE 25MM2 25 7.7 EA 1 HT130-C-35 COPPER HEXAGONAL DIE 35MM2 35 9.2 EA 1 HT130-C-50 COPPER HEXAGONAL DIE 50MM2 50 10.4 EA 1 HT130-C-70 COPPER HEXAGONAL DIE 70MM2 70 11.5 EA 1 HT130-C-95 COPPER HEXAGONAL DIE 95MM2 95 14.2 EA 1 HT130-C-120 COPPER HEXAGONAL DIE 120MM2 120 16.5 EA 1 HT130-C-150 COPPER HEXAGONAL DIE 150MM2 150 18.3 EA 1 HT130-C-185 COPPER HEXAGONAL DIE 185MM2 185 20.0 EA 1 HT130-C-240 COPPER HEXAGONAL DIE 240MM2 240 23.1 EA 1 HT130-C-300 COPPER HEXAGONAL DIE 300MM2 300 26.0 EA 1 COPPER C CONNECTOR DIES 12T Dies 12/13 tonne crimp heads for heavy duty C-connectors CACD and CACE range Oval crimp on C-connector Part No. Description Unit Qty HT130-CC C CONNECTOR CRIMPING DIES 10-35 MM2 EA 1 HT130-C0 C CONNECTOR CRIMPING DIES 35-70 MM2 EA 1 HT130-C997 C CONNECTOR CRIMPING DIES 95-120 MM2 EA 1 HT130-C1011 C CONNECTOR CRIMPING DIES 150-240 MM2 EA 1 COPPER DIESETS 12T/13T 12 TON DIE SET 16-300MM2 Part No. DIESET 12/13 tonne dies for Australian and New Zealand dimensioned lugs and links Hexagonal crimp die kit for Cu Copper dies 16sq.mm to 300mm2 13 TON DIE SET Unit: KIT Qty: 1 Part No. DIESET2 12/13 tonne dies for Australian and New Zealand dimensioned lugs, links and overhead line sleeves Hexagonal crimp die kit for Cu and Al Cu dies 16 to 300 sq.mm and Al dies 6 to 300mm2 C356

COPPER DIES 23T Crimping dies for Australian and New Zealand dimensioned lugs and links Hexagonal crimp dies for Copper lugs and links Suitable for 22/23 tonne hydraulic crimping heads Part No. Description Nominal Conductor A/F Hex Die Unit Qty (mm 2 ) (mm) ECW-H3D-400 DIE - ECW-H3D 400MM2 COPPER 400 28.1 EA 1 ECW-H3D-500 DIE - ECW-H3D 500MM2 COPPER 500 31 EA 1 ECW-H3D-630 DIE - ECW-H3D 630MM2 COPPER 630 37 EA 1 COPPER DIES 53T Die for 52 tonne crimp heads for Australian and New Zealand dimensioned Copper lugs and links Hexagonal crimp die Die range for large Copper lugs and links up 1000 sq.mm Adaptor RHU520-AD available for 13 tonne C dies Part No. Description Nominal Conductor A/F Hex Die Unit Qty (mm 2 ) (mm) RHU520-400 HEX. DIE 400MM A/F 28.1 400 28.1 EA 1 RHU520-500 HEX. DIE 500MM A/F 31.0 500 31.0 EA 1 RHU520-630 HEX. DIE 630MM A/F 37.0 630 37.0 EA 1 RHU520-800 HEX. DIE 800MM A/F 43.2 800 43.2 EA 1 RHU520-1000 HEX. DIE 1000MM A/F 48.0 1000 48.0 EA 1 DIES EARTHING COPPER C CONNECTOR DIES 12T COPPER C CONNECTOR CACC DIE Part No. HT-CACC Crimping die C type for 12/13 tonne crimper for CACC70 C-connector Based on old style range Made from heat treated carbon steel Also see MC70-C and other dies for CACC range COMPRESSION DIE FOR CAEC Part No. HT-CAEC Die to suit earthing rod C-connectors range CAEC Die fits all sizes of CAEC C-connector range Suitable for crimping C-connector CACC95 C357

HT CACC C-CONNECTOR DIES 12T Die for CACC range of earth bonding and tap off C-connectors 12/13 tonne crimp tool C-type hexagonal crimp die Part No. Description Unit Qty MC25-C DIE CACC25 HT&B SERIES TOOLS EA 1 MC35-C DIE CACC35 HT&B SERIES TOOLS EA 1 MC70-C DIE CACC70 HT&B SERIES TOOLS EA 1 MC95-C DIE CACC95 HT&B SERIES TOOLS EA 1 MC185-C DIE CACC120 HT&B SERIES TOOLS EA 1 DIES INDENT CRIMP INDENT CRIMP DIES 12T Indent die for 12/13 tonne Aluminium solid sector conductor Suitable for Australian and New Zealand sector lugs and links Requires a NEST die for sector crimps Part No. Description Unit Qty HT130-A16INDENT INDENT SECT. ALUM 3/4 CORE 120MM EA 1 HT130-A18INDENT INDENT SECT. ALUM 3/4 CORE 185MM EA 1 HT130-A19INDENT INDENT SECT. ALUM 3/4 CORE 240MM EA 1 C358

DIES ALUMINIUM ALUMINIUM DIES 5T SPECIALIST TOOLS AND ACCESSORIES Dies to suit 5 tonne crimp tools for Australian and New Zealand dimensioned Aluminium lugs and links Hexagonal crimp dies Part No. Description Nominal Conductor A/F Hex Die Unit Qty (mm 2 ) (mm) M90-50 HT51 HEX ALUM DIE 16-35MM A/F 9.0MM 16 9.0 EA 1 M132-50 HT51 HEX ALUM DIE 50-70MM A/F 13.2MM 50 13.2 EA 1 M140-50 HT51 HEX ALUM DIE ABC 25MM A/F 14.0MM 25 14.0 EA 1 M173-50 HT51 HEX ALUM DIE ABC 35-70MM A/F 17.3MM 95 17.3 EA 1 M215-50 HT51 HEX ALUM DIE ABC 95-150MM AF 21.5MM 150 21.5 EA 1 M220-50 HT50 HEX ALUM DIE 150-185MM A/F 22.0MM 185 20.0 EA 1 ALUMINIUM DIES 12/13T Dies to suit Australian and New Zealand dimensions Aluminium lugs, links and overhead line sleeves C-type die for 12/13 tonne crimp tools Hexagonal crimp dies Part No. Description Conductor Range A/F Hex Die Unit Qty (mm 2 ) HT-6/35AL ALUMINIUM HEX.DIE 9.00MM A/F 6-32MM 6-35 9.0 EA 1 HT-7/225AL ALUMINIUM HEX DIE 14.0MM A/F 7-225 14.0 EA 1 HT-7/250AL ALUMINIUM HEX DIE 14.5MM A/F 7-250 14.5 EA 1 HT-7/300-375AL ALUMINIUM HEX DIE 18.0MM A/F 300-375 18.0 EA 1 HT-7/450AL ALUMINIUM HEX DIE 19.0MM A/F 7-450 19.0 EA 1 HT-19/375AL ALUMINIUM HEX DIE 26.2MM A/F 19-375 26.2 EA 1 HT-50/70AL ALUMINIUM HEX DIE 13.2MM A/F 50-70MM 50-70 13.2 EA 1 HT-95/120AL ALUMINIUM HEX DIE 17.3MM A/F 95-120MM 95-150 17.3 EA 1 HT-150/185AL ALUMINIUM HEX DIE 22.0MM A/F 150-185MM 150-185 22.0 EA 1 HT-240/300AL ALUMINIUM HEX DIE 28.4MM A/F 240-300MM 240-300 28.4 EA 1 ALUMINIUM ABC DIES 12T 12/13 tonne C-type dies for ABC lugs and links Hexagonal crimp dies Part No. Description Conductor Range A/F Hex Die Unit Qty (mm 2 ) HT-25ABC ALUMINIUM DIE 25MM2 ABC 25 14.0 EA 1 HT-35/95ABC ALUMINIUM DIE 35/95MM2 ABC 35-95 17.3 EA 1 HT-95/150ABC ALUMINIUM DIE 95/150MM2ABC 95-150 21.5 EA 1 C359

ALUMINIUM DIESETS 12/13T ALUMINIUM DIE SET Unit: KIT Qty: 1 Part No. DIESET3 12/13 tonne dies for Australian and New Zealand dimensioned lugs and links Hexagonal crimp die kit for Al Aluminium dies for 6 sq.mm to 300 sq.mm ALUMINIUM DIES 23T Crimping dies for Australian and New Zealand dimensioned lugs and links Hexagonal crimp dies for Aluminium lugs and links Suitable for 22/23 tonne hydraulic crimping heads Part No. Description Nominal Conductor (mm 2 ) A/F Hex Die (mm) Unit Qty ECW-H3D4/500AL DIE ALUM. ECW-H3D 400/500 500 39.0 EA 1 ALUMINIUM DIES 53T Die for 52 tonne crimp head for Australian and New Zealand dimensioned Aluminium lugs and links Hexagonal crimp die Made from heat treated carbon steel Part No. Description Nominal Conductor A/F Hex Die Unit Qty (mm 2 ) (mm) RHU520-4/500AL HEX. DIE ALUM. 4/500MM A/F 39.0 500 39.0 EA 1 RHU520-1000AL HEX. DIE ALUM. 1000MM A/F 52.5 1000 52.5 EA 1 DIES ALUMINIUM NEST CRIMP ALUMINIUM NEST CRIMP DIE 12T NEST dies for 12/13 tonne Aluminium solid sector conductor Suitable for Australian and New Zealand sector lugs and links Requires an indent die for sector crimps Part No. Description Unit Qty HT130-A14NEST NEST SECT. ALUM 4 CORE 70-120MM EA 1 HT130-A12NEST NEST SECT. ALUM 3 CORE 70-300MM EA 1 HT130-A15NEST NEST SECT. ALUM 4 CORE 150-300MM EA 1 C360

DIES CUTTING CUTTING DIES 5T HT50 WIRE CUTTING DIE 10MM O SPECIALIST TOOLS AND ACCESSORIES Part No. MB52-50 Cutting dies for 5 tonne hydraulic crimping tools to cut copper or aluminium No adjustments required Less costly than dedicated cutting tools Suitable for cutting up to 10mm diameter wire CUTTING DIES 13T WIRE CUTTER DIE - 12T Part No. HT-131-CD Cutting die for 12/13 tonne C-type hydraulic crimping tools, with a cutting diameter of 16mm Australian designed and manufactured Less costly than dedicated cutting tools No adjustments required for cutting different materials Suits all 12/13 tonne C or U style crimp tools CUTTING DIES 23T CUTTING DIE SET FOR ECW-H3D CRIMP HEAD Part No. WT2-30 Cutting die for 22/23 tonne hydraulic crimping tools with a cutting diameter of 20mm DIES INSULINK INSULINK DIES 5T HT50 DIE-ALL SIZE INSULINK 35MM Part No. MC35-50 Die for Burndy Insulink One die fits all ADAPTORS ADAPTORS 12T ADAPTOR ECW-H3D 12 TON DIES Part No. ECW-H3D-AD Adaptor for 22/23 tonne crimp head to fit 12/13 tonne C-type crimp dies Suits Cembre crimp head ECW-H3D Adapts 23 tonne tool to crimp large range of lugs and links C361

ADAPTOR RHU520 TO 12 TON DIE Part No. RHU520-AD Adaptor allows use 13 tonne C-type dies with RHU520 52 tonne crimp heads Fits standard 12/113 tonne C-dies Extends range of RHU520 to smaller size crimp dies HYDRAULIC POLE SAWS HYDRAULIC POLE SAW Designed for safely trimming branches from either an aerial bucket or the ground Light-weight and balanced with strong insulated fibreglass pole Packed with safety features Designed with a Cool Running handle for operator comfort Can be used on both open and closed hydraulic systems Part No. Description Unit Qty MSS-HPS-1500-FF-C POLE SAW 150CM FOAM FILLED WITH COUPLERS EA 1 MSS-HPS-1800-FF-C POLE SAW 180CM FOAM FILLED WITH COUPLERS EA 1 C362