W-150-IS Specifications MOTOR/TIMER ENCLOSURE 14 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL 10.25 2 PIPE / EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY GC-7 GREASE 8 QUART CAPACITY 15.5 17.5 END VIEW 25.5 SIDE VIEW 28.5 FEATURES: Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with 24-hour timer and Grease Collector. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior. Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. Compact footprint. TOP VIEW Two (2) No-Hub Connectors provided. TECHNICAL DATA Materials: Electrical: Maximum Inlet Flow Rate: Number of Skimming Wheels: Skimming Rate: Grease Retention Capacity: Internal Solids Strainer Capacity: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene 115 VAC, 60 Hz, 520 Watts (4.5 Amps) 15 GPM 1 20 Pounds Per Hour 30+ Pounds 1.85 Gallons 1/06 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 1
W-150-IS Specifications 4 INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions 25.5 DO... Allow a minimum of 14 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. 6.5 4.5 GC-7 GREASE Make piping connections with rubber No Hub connectors (provided). Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-150-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 15 gallons per minute peak flow, 30 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, a lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004. Electric motor shall be equipped with thermal overload protection with automatically resettable switch. Two (2) no-hub connectors for plumbing connection provided. 2 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 1/06
MOTOR/TIMER ENCLOSURE Big Dipper Point Source Automatic W-200-IS Specifications 14 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL 14.75 EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY GC-7 GREASE 8 QUART CAPACITY 10.5 10.5 20 2 PIPE / FEATURES: 17.5 END VIEW 22.5 SIDE VIEW 25.5 Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with 24-hour timer and Grease Collector. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior. Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. Compact footprint. Two (2) No-Hub Connectors provided. TOP VIEW TECHNICAL DATA Materials: Electrical: Maximum Inlet Flow Rate: Number of Skimming Wheels: Skimming Rate: Grease Retention Capacity: Internal Solids Strainer Capacity: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene 115 VAC, 60 Hz, 520 Watts (4.5 Amps) 20 GPM 1 20 Pounds Per Hour 40+ Pounds 1.85 Gallons 1/06 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 3
W-200-IS Specifications 4 INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions 22.5 DO... Allow a minimum of 14 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. Make piping connections with rubber No Hub connectors (provided). Keep outlet piping as straight as possible. Use only sweep connections. 6.5 4.5 GC-7 GREASE Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-200-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 20 gallons per minute peak flow, 40 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, a lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004. Electric motor shall be equipped with thermal overload protection with automatically resettable switch. Two (2) no-hub connectors for plumbing connection provided. 4 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 1/06
MOTOR/TIMER ENCLOSURE Big Dipper Point Source Automatic W-250-IS Specifications 14 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL 14.75 EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY GC-7 GREASE 8 QUART CAPACITY 10.5 10.5 20 2 PIPE / 17.5 END VIEW 25.5 SIDE VIEW 28.5 FEATURES: Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with 24-hour timer and Grease Collector. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior. Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. Compact footprint. TOP VIEW Two (2) No-Hub Connectors provided. TECHNICAL DATA Materials: Electrical: Maximum Inlet Flow Rate: Number of Skimming Wheels: Skimming Rate: Grease Retention Capacity: Internal Solids Strainer Capacity: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene 115 VAC, 60 Hz, 520 Watts (4.5 Amps) 25 GPM 1 20 Pounds Per Hour 50+ Pounds 1.85 Gallons 1/06 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 5
W-250-IS Specifications 4 INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions 25.5 DO... Allow a minimum of 14 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. 6.5 4.5 GC-7 GREASE Make piping connections with rubber No Hub connectors (provided). Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-250-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 25 gallons per minute peak flow, 50 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, a lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004. Electric motor shall be equipped with thermal overload protection with automatically resettable switch. Two (2) no-hub connectors for plumbing connection provided. 6 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 1/06
MOTOR/TIMER ENCLOSURE Big Dipper Point Source Automatic W-350-IS Specifications 14 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL 17.85 EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY GC-7 GREASE 8 QUART CAPACITY 12.5 12.5 23.1 3 PIPE / FEATURES: 17.5 END VIEW 34.4 SIDE VIEW 37.4 Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with 24-hour timer and Grease Collector. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior. Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. Compact footprint. TOP VIEW Two (2) No-Hub Connectors provided. TECHNICAL DATA Materials: Electrical: Maximum Inlet Flow Rate: Number of Skimming Wheels: Skimming Rate: Grease Retention Capacity: Internal Solids Strainer Capacity: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene 115 VAC, 60 Hz, 520 Watts (4.5 Amps) 35 GPM 1 20 Pounds Per Hour 70+ Pounds 2.5 Gallons 1/06 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 7
W-350-IS Specifications 4 INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions 34.4 DO... Allow a minimum of 14 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. Make piping connections with rubber No Hub connectors (provided). 6.5 4.5 DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). GC-7 GREASE Reduce pipe size on outlet piping. Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-350-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 35 gallons per minute peak flow, 70 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, a lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004. Electric motor shall be equipped with thermal overload protection with automatically resettable switch. Two (2) no-hub connectors for plumbing connection provided. 8 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 1/06
MOTOR/TIMER ENCLOSURE Big Dipper Point Source Automatic W-500-IS Specifications 14 CLEARANCE FROM TOP OF TANK REQUIRED FOR STRAINER BASKET & LID REMOVAL EMPTY INTO COOKING OIL RECYCLING CONTAINER DAILY 17.85 17.5 3 PIPE / END VIEW GC-7 GREASE 8 QUART CAPACITY 12.5 12.5 42.4 SIDE VIEW 45.4 23.1 FEATURES: Fully automatic self cleaning cycle. Removes collected grease & oils from tank without any operator assistance. Comes complete with 24- hour timer and Grease Collector. Constructed of corrosion resistant materials suitable for installation in virtually any location. Attractive sanitary Stainless Steel exterior. TOP VIEW Integrated Motor/Grease Outlet/Heater/Lid enables a fast, do-it-yourself unit operation reversal. Compact footprint. Two (2) No-Hub Connectors provided. TECHNICAL DATA Materials: Electrical: Maximum Inlet Flow Rate: Number of Skimming Wheels: Skimming Rate: Grease Retention Capacity: Internal Solids Strainer Capacity: Exterior: 304 Stainless Steel, Bright Finish Interior: Rotationally Molded Polyethylene 115 VAC, 60 Hz, 520 Watts (4.5 Amps) 50 GPM 1 20 Pounds Per Hour 100+ Pounds 2.5 Gallons 1/06 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 9
W-500-IS Specifications 4 INSTALLATION INFORMATION Suggested Minimum Footprint Dimensions 42.4 DO... Allow a minimum of 14 clearance from top of tank for removal of unit lid. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make sure the height above the Internal Strainer Access Cover is enough to remove the strainer. 6.5 4.5 GC-7 GREASE Make piping connections with rubber No Hub connectors (provided). Keep outlet piping as straight as possible. Use only sweep connections. Install vent on outlet piping. Fill the tank with water before energizing the power to the motor and heater. Set Programmable Time Controller for proper operating times. DONʼT... Install P trap on outlet connection of tank. (Note: the unit already has an internal gas trap). Reduce pipe size on outlet piping. Note: Installations must comply with all applicable local, state, and national codes for your area. Job Specification: Grease and oils separator(s) shall be Thermaco Big Dipper automatic grease/oil recovery system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install Thermaco Big Dipper Model No. W-500-IS, bright finish type 304 stainless steel exterior, rotationally molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 50 gallons per minute peak flow, 100 pounds of grease capacity and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, an integral programmable 24-hour multi-event time control, a field reversible motor location, a field reversible grease/oil sump outlet, quick release stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, a lift-out strainer basket access, an internal stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004. Electric motor shall be equipped with thermal overload protection with automatically resettable switch. Two (2) no-hub connectors for plumbing connection provided. 10 646 Greensboro St. Asheboro, N. C. 27204-2548 Phone (336) 629-4651 North America: (800) 633-4204 1/06