PROCESS ANALYSERS SERVOTOUGH Oxy Gas Analyser Certification Supplement Manual Part Number: 01910008B Revision: 9 Language: UK English
This page intentionally blank
SERVOTOUGH Oxy Certification Supplement Manual CONTENTS 1. INTRODUCTION 2. EU DECLARATION OF CONFORMITY 3. ATEX CERTIFICATION 4. INTERNATIONAL (IECEx) APPROVALS 5. NORTH AMERICAN (CSA) APPROVALS 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual 1. INTRODUCTION The SERVOTOUGH Oxy has been approved by various authorities for installation in hazardous areas. The certification offered with a specific analyser configuration will depend upon specification and country of delivery. See the certification labels attached to the analyser for exact approval details. The following information summarises the approvals that have been obtained. If the analyser is installed in a hazardous area then the electrical power, gland entries and NPT blanking plugs and connecting cables should be installed and protected according to conditions on the relevant certificates, national wiring regulations, hazardous area codes of practice and local authority regulations. About this manual: Part Number: 01910008B Revision: 9 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual 2. EU DECLARATION OF CONFORMITY 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual 3. ATEX CERTIFICATION The analyser is ATEX certified to: II 2G Ex ia db IIC T4 Gb (-10 C Ta +60 C) or II 2D Ex tb IIIC T90 C Db (-10 C Ta +60 C) or II 2GD Ex ia db IIC T4 Gb (-10 C Ta +60 C) Ex tb IIIC T90 C Db (-10 C Ta +60 C) Certificate number: Baseefa 09ATEX0080X See certificate below: 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual 4. INTERNATIONAL (IECEx) APPROVALS The analyser is IECEx certified to: Ex ia db IIC T4 Gb (-10 C Ta +60 C) Ex tb IIIC T90 C Db (-10 C Ta +60 C) Certificate number: IECEx BAS09.0029X See certificate below: 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
SERVOTOUGH Oxy Certification Supplement Manual 5. NORTH AMERICAN (CSA) APPROVALS The analyser is CSA approved for use in the USA and Canada in the following locations: Class I, Division 1, Groups A, B, C, D T4 (-10 C Ta +60 C) Class II, Division 1, Groups E, F, G (-10 C Ta +60 C) Class III, (-10 C Ta +60 C) Class I, Zone 1, Ex ia d IIC T4 (-10 C Ta +60 C) Class I, Zone 21, Ex td T90 C Class I, Zone 1, AEx ia d IIC T4 (-10 C Ta +60 C) Class I, Zone 21, AEx td T90 C Certificate number: CSA 08.1961540 See certificate below: 01910008B
SERVOTOUGH Oxy Certification Supplement Manual Blank 01910008B
Certificate of Compliance Certificate: 1961540 Master Contract: 153364 (068207_0_000) Project: 70118771 Date Issued: 2017-03-01 Issued to: Servomex Group Ltd. Millbrook Industrial Estate Jarvis Brook Crowborough, East Sussex TN6 3FB UNITED KINGDOM Attention: Nigel Pickett The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. Issued by: Salvatore Grasso Salvatore Grasso PRODUCTS CLASS 2258 03 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non-Incendive Systems - For Hazardous Locations CLASS 2258 83 - PROCESS CONTROL EQUIPMENT-Intrinsically Safe and Non-Incendive-Systems- For Hazardous Locations-Certified to U.S. Standards Class I, Division 1, Groups A, B, C, D T4; Class II Division 1, Groups E, F, G; Class III: Ex ia d IIC T4, Ex td T90 C AEx ia d IIC T4, AEx td T90 C Series 1900 Digital Gas Analyzer (Models 1910 also identified as Model Servotough Oxy and Model 1920 also identified as Model Servotough Spectra), -10 C Ta 60 C, 100-120 or 220-240 Vac, 50-60 Hz, 50 VA Notes: 1. The Digital Gas Analyzer is not intended to be used as a Combustible Gas Detector for sensing Lower Explosive Limit (LEL). 2. The Digital Gas Analyzer is to be protected by an external 10 A circuit breaker. DQD 507 Rev. 2016-02-18 Page 1
Certificate: 1961540 Project: 70118771 Master Contract: 153364 Date Issued: 2017-03-01 3. Only concentrations of sample gas up to 21% O 2 are permitted in a hazardous location. 4. Only a sample gas with a pressure up to 18 psia may be used in a hazardous location. APPLICABLE REQUIREMENTS ANSI/ISA 60079-0:2005 Apparatus for explosive gas atmospheres General requirements ANSI/ISA 60079-1:2005 Apparatus for explosive gas atmospheres Flameproof enclosures ANSI/ISA 60079-11:2002 Apparatus for explosive gas atmospheres Intrinsic safety ANSI/ISA 61241-0:2006 Electrical Apparatus for Use in Zone 20, Zone 21 and Zone 22 Hazardous (Classified) Locations General Requirements ANSI/ISA 61241-1:2006 Electrical Apparatus for Use in Zone 21 and Zone 22 Hazardous (Classified) Locations Protection by Enclosures td CAN/CSA C22.2 No. 0-M91 General Requirements Canadian Electrical Code, Part II CSA-C22.2 No. 25-1966 Enclosures for Use in Class II Groups E, F, and G Hazardous Locations. CAN/CSA-C22.2 No. 30-M1986 Explosionproof Enclosures for use in Class I Hazardous Locations. CAN/CSA C22.2 No. 157-92 Intrinsically Safe and Non-Incendive Equipment CSA E60079-0:02 Apparatus for explosive gas atmospheres General requirements CSA E60079-1:02 Apparatus for explosive gas atmospheres Flameproof enclosures CSA E60079-11:02 Apparatus for explosive gas atmospheres Intrinsic safety CSA/ISA 61010-1:2004 (2 nd Ed) Safety Requirements for Electrical Equipment for Control CAN/CSA-E61241-1-1-02 Electrical Apparatus for Use in the Presence of Combustible Dust Part 1-1: Electrical Apparatus Protected by Enclosures and Surface Temperature Limitation - Specification for Apparatus DQD 507 Rev. 2016-02-18 Page 2
Certificate: 1961540 Project: 70118771 Master Contract: 153364 Date Issued: 2017-03-01 MARKINGS The manufacturer is required to apply the following markings: Products shall be marked with the markings specified by the particular product standard. Products certified for Canada shall have all Caution and Warning markings in both English and French. Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where applicable, in accordance with the requirements of those authorities. The products listed are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US (indicating that products have been manufactured to the requirements of both Canadian and U.S. Standards) or with adjacent indicator 'US' for US only or without either indicator for Canada only. Nameplate adhesive label material approval information: The following markings are provided on a cul approved adhesive-type 3M 7879EJ PET rectangular label. Round label is aluminum, minimum 0.5 mm thick and retained to the enclosure with a drive screw. Markings are per drawing 01910/876CS. - Manufacturer s name: "Servomex Ltd", or CSA Master Contract Number 153364, adjacent to the CSA Mark in lieu of manufacturer s name. - Model number: As specified in the PRODUCTS section, above. - Electrical ratings: As specified in the PRODUCTS section, above. - Manufacturing date in MMYY format, or serial number, traceable to month of manufacture. - Hazardous Location designation: As specified in the PRODUCTS section, above (may be abbreviated). - Optional marking (Class I, Zone 1; Class II, Zone 21); - CSA Monogram with adjacent indicators, C and US for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only; - CSA Certificate number 08.1961540 (adjacent to CSA monogram); - Maximum ambient with related T Code (T4 @ 60 C max); (T90 C @ 60 C max) or optionally (T4 @ 50 C max); (T90 C @ 50 C max) - The following words or the equivalent: o WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY and AVERTISSEMENT: LA SUBSTITUTION DE COMPOSANTS PEUT COMPROMETTRE LA SECURITE INTRINSEQUE o WARNING: DO NOT OPEN WHEN AN EXPLOSION ATMOSPHERE MAY BE PRESENT and AVERTISSEMENT: NE PAS OUVRIR SI UNE ATMOSPHERE D'EXPLOSION PEUT ETRE PRESENTE o A SEAL SHALL BE INSTALLED WITHIN 450 mm OF THE ENCLOSURE and UN SCELLEMENT DOIT ÊTRE INSTALLÉ À MOINS DE 450 mm DU BOÎTIER. o WARNING: This apparatus is not designed for use in oxygen enriched atmospheres and AVERTISSEMENT: Cet appareil n'est pas conçu pour une utilisation dans des atmosphères enrichies en oxygène All units are provided with an instruction manual. DQD 507 Rev. 2016-02-18 Page 3
Supplement to Certificate of Compliance Certificate: 1961540 Master Contract: 153364 (068207_0_000) The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Project Date Description Product Certification History 70118771 2017-03-01 Update of report 1961540 for Models 01910 and 01920 to include revised drawings to: 1. Minor drawing changes that rationalize and clarify details for latest IEC standards. 2. Specification of Gore-Tex breathers amended due to obsolescence. Per review of submitted IEC ExTR Variation report With no change to Product Listing / Cert Record. 2716309 2014-05-01 Update to report 1961540 to include revised drawings. 2375403 2011-01-27 Update to report 1961540 to include replacement fuses on Barrier Boards (01910/853 & 01910/863). 2309260 2010-07-21 Update Report 1961540 for alternate construction. 2202536 2010-01-27 Update Report 1961540 for alternate construction, Type IP66 rating, td rating and Class II. 2218209 2009-11-05 Update Report 1961540 for alternate construction, Type 4X rating and 240 V supply rating. 2188165 2009-06-18 Update Report 1961540 to add alternate cable gland. 2144102 2009-06-08 Update Report 1961540 to identify as Series 1900 Analyzers and add new Boards and alternate construction. 1961540 2008-03-04 Original certification of Series 1900IR Digital Gas Ana lyzers for Division 1 and Zone 1. DQD 507 Rev. 2016-02-18 Page 1