OT ASSE 117 4 2 1-1 2 3 R F 8 14 4 5 1 12 ASSE 117 VALVE O. RANSTON RI USA AS SE 117 TYP TM US. Patents 2.97, 3,61,195 3.152,7 4 2 1-1 2 F 3 R 8 5 14 4 1 12 VALVE O. RANSTON RI USA ASSE 117 U S. Pate nt s 2.9 7, 3, 6 1,1 9 5 3.1 52,7 Bulletin G11N2 January 214 INSTALLATION ADJUSTMENT SERVIE TM-152A-2P, 2P TM-152A-2P-LF 2P TM-22B-2P, TM22B-2P-LF PARALLEL SYSTEMS Note: IMPORTANT! Provide serial numbers for both valves when ordering parts!! INSTALLATION 38" TYP TM 39" L OT 28" 4 2" 1 2 OLD OT 28" OLD TM-22B-2P Small valve manufactured after July 27 starting with serial # TM26272 1. Type TM Parallel Systems are factory pre-assembled and tested and include large and small thermostatic water mixing valves which function as a system to meet both high and low demand for tempered water. 2. System should be installed at a location where it can easily be cleaned, adjusted or repaired. 3. System supplies must be connected as shown (ot-left, old-right). Exercise caution when soldering. TM-152A-2P Small valve manufactured after July 27 starting with serial # TM239272 4. Flush pipes thoroughly after system has been connected. 5. Assemblies installed on a recirculated hot water system MUST be piped according to S REQUIRED PIPING METOD #5 (see page 4). 6. Refer to page 3 of this bulletin for correct Setup Instructions. Maximum Operating Pressure 125PSI (8 KPA) for ot and old Water. AUTION All thermostatic water-mixing valves have limitations. They will not provide the desired accuracy outside of their flow capacity range. onsult the capacity chart on page 12. Minimum flow must be no less than as shown. 13 Elmwood Avenue, ranston, RI 291 USA Phone: 41.461.12 Fax: 41.941.531 Email: info@leonardvalve.com Web Site: http://www.leonardvalve.com
ASSE 117 TM-22B-2P ADJUSTMENT AND SERVIE ONLY Leonard Type TM Thermostatic Water Mixing Valves are simple in design and may be easily cleaned, adjusted and repaired. If the installation is accessible, servicing may be completed without disconnecting the valves. NOTE: Parallel Systems include Thermostatic Water Mixing Valves, which must be regularly maintained to provide best performance. Frequency of cleaning depends on quality of local water conditions and usage. See Maintenance Guide and Record MGR-1 WARNING These mixing valves are equipped with an adjustable high temperature limit stop factory set at approximately 12 F (49 ) with an incoming hot water supply temperature of 15 F (65.5 ). If the hot water supply temperature of the job is greater than 15 F (65.5 ), 5 ) the valves when turned to full OT will deliver water in excess of 12 F (49 ) and the limit stop MUST BE RESET BY TE INSTALLER! TO RESET ADJUSTABLE IG TEMPERATURE LIMIT STOP: TM-22B LARGE MIXING VALVES TM-22B SMALL MIXING VALVES STOP SREW SREW OLD FINE ADJUSTMENT SREW OT SNAP AP LTR SET SREW 1. Loosen LTR screw 2. Remove SNAP AP, SREW & WASER, Remove. 3. Temporarily place on the spline rod, turn RIGT for warmer temperature, turn LEFT for cooler temperature. When valve is delivering warmest temperature desired, remove the pointer. 4. Replace on the spline rod so that its RIGT edge is resting against the STOP SREW located on the RIGT SIDE OF TE. 5. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE RESET AND REEKED EA TIME ANDLE IS REMOVED. WEB (REST STOP AGAINST SREW) STOP LTR SET SREW 1. Loosen LTR Set Screw, remove SREW. 2. Adjust to maximum desired temperature. 3. Remove, replace on spline rod with STOP (which is cast into the underside on the pointer), resting against the BOTTOM side of the WEB on the FINE ADJUSTMENT SREW. 4. If fine adjustment is needed, adjust FINE ADJUSTMENT SREW on the cover, loosen for hotter or tighten for cooler temperature. 5. Replace and check temperature, if set to desired temperature replace SREW, and tighten LTR SET SREW. 6. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE RESET AND REEKED EA TIME ANDLE IS REMOVED. IMPORTANT! ALL MIXING VALVES MUST BE SET AT TE SAME OPERATING TEMPERATURE. SEE PAGES: 6 & 7 FOR OMPLETE PARTS BREAKDOWN heck for significant variations in outlet flow. Thermostatic valves will NOT provide the desired accuracy outside of their flow capacity range. Minimum flows must be no less than shown (see Flow apacities, page 12). If installed on a recirculated hot water system, make certain the valve is piped according to Leonard s Required Piping Methods (see page 4). REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. (SEE MAINTENANE GUIDE AND REORD, MGR-1). 2
117 ASSE TM-152A-2P ADJUSTMENT AND SERVIE ONLY Leonard Type TM Thermostatic Water Mixing Valves are simple in design and may be easily cleaned, adjusted and repaired. If the installation is accessible, servicing may be completed without disconnecting the valves. NOTE: Parallel Systems include Thermostatic Water Mixing Valves, which must be regularly maintained to provide best performance. Frequency of cleaning depends on quality of local water conditions and usage. See Maintenance Guide and Record MGR-1 WARNING These mixing valves are equipped with an adjustable high temperature limit stop factory set at approximately 12 F (49 ) with an incoming hot water supply temperature of 15 F (65.5 ). If the hot water supply temperature of the job is greater than 15 F (65.5 ), 5 ) the valves when turned to full OT will deliver water in excess of 12 F (49 ) and the limit stop MUST BE RESET BY TE INSTALLER! TO RESET ADJUSTABLE IG TEMPERATURE LIMIT STOP: TM-152A LARGE MIXING VALVE TM-152A SMALL MIXING VALVE STOP SREW OT OLD FINE ADJUSTMENT SREW LTR SET SREW SNAP AP 1. Loosen LTR screw 2. Remove SNAP AP, SREW & WASER, Remove. 3. Temporarily place on the spline rod, turn RIGT for warmer temperature, turn LEFT for cooler temperature. When valve is delivering warmest temperature desired, remove the pointer. 4. Replace on the spline rod so that its RIGT edge is resting against the STOP SREW located on the RIGT SIDE OF TE. 5. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE RESET AND REEKED EA TIME ANDLE IS REMOVED. WEB REST AGAINST SREW 1. Loosen LTR SET SREW, remove SREW. 2. Adjust to maximum desired temperature. 3. Remove, replace on spline rod with STOP (which is cast into the underside on the pointer), resting against the BOTTOM side of the WEB on the FINE ADJUSTMENT SREW. 4. If fine adjustment is needed, adjust FINE ADJUSTMENT SREW on the cover, loosen for hotter or tighten for cooler temperature. 5. Replace and check temperature, if set to desired temperature replace SREW, and tighten LTR SET SREW. 6. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. * LIMIT STOP MUST BE RESET AND REEKED EA TIME ANDLE IS REMOVED. IMPORTANT! ALL MIXING VALVES MUST BE SET AT TE SAME OPERATING TEMPERATURE. SEE PAGES: 9 & 11 FOR OMPLETE PARTS BREAKDOWN heck for significant variations in outlet flow. Thermostatic valves will NOT provide the desired accuracy outside of their flow capacity range. Minimum flows must be no less than shown (see Flow apacities, page 12). If installed on a recirculated hot water system, make certain the valve is piped according to Leonard s Required Piping Methods (see page 4). REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. (SEE MAINTENANE GUIDE AND REORD, MGR-1). 3
ASSE 117 4 2-1 2 R F 3 8 5 14 4 ASSE 117 SETUP INSTRUTIONS FOR BOT 22B-2P AND 152A-2P TERMOMETER V1L 1 V2L LVL 1 12 V2R V1R LVR SVL SVR OT INLET OLD INLET 1. The Parallel Unit MUST be piped according to a Leonard 8. Open ball valve V2R and shut ball valve V2L at the mixing Required Piping Method 5 (see page 4). valve. 2. Make sure full hot and cold supplies to this assembly are 9. Set outlet temperature of the mixing valve LVR to the same operating. The temperature of the hot water source must be temperature as step 7. properly set and maintained. 1. Turn off enough fixtures for a flow of at least 2 GPM (7.6 3. The circulator (if used) must be turned OFF before setup. l/min) downstream from this system. Make sure each fixture 4. Turn on enough fixtures for a flow of at least 3 GPM (114 is set to deliver full "OT" water. l/min.) downstream from this system. Make sure each fixture 11. Open V1L, shut off ball valve V2R is set to deliverer full ll"ot" water. 5. lose outlet ball valves V1R,V2R, V1L. 6. Make sure ball valve V2L is in the full open position. 7. Set outlet temperature of the mixing valve LVL to the required level. 12. Set outlet temperature of mixing valve SVL to the same temperature as Step 7. 13. Open V1R and shut V1L, set outlet temperature of SVR mixing valve to the same temperature as STEP 7. 14. Open all outlets. System is operational. To balance circulation system temperature, see page 5. NOTE! FOR OPTIONAL OUTLET SETUP PIPING ARRANGEMENT, SEE PAGE 12 4
ASSE 117 4 2 1-1 2 LEON ARD F 3 8 4 5 14 1 12 ASSE 117 REQUIRED PIPING METOD #5 IG TEMPERATURE FIXTURES SYSTEM FIXTURES BALL VALVE FOR SETUP (OPTIONAL) FULL RETURN LINE SIZE OT WATER OURE EAT TRAP BALANING VALVE #2 WIT EK TEMPERED IRULATOR EK VALVE ISOLATION VALVE T AQUASTAT D PLY EK VALVE BALANING VALVE #1 IG TEMPERATURE RETURN IRULATOR TEMPERED RETURN PROEDURE TO BALANE IRULATION SYSTEM 1. MAKE SURE NO WATER IS BEING DRAWN IN TE BUILDING. OPEN BALANING VALVE #1 APPROXIMATELY ALF WAY AND START IRULATOR. KEEP BALANE VALVE #2 LOSED AT TIS TIME 2. OBSERVE TEMPERATURE UNTIL IT STABILIZES. 3. LOSE BALANING VALVE #1 SLIGTLY IF TEMPERATURE IS TOO OT, OR OPEN IT SLIGTLY IF TEMPERATURE IS TOO OLD. ALLOW TEMPERATURE TO STABILIZE, REPEAT UNTIL DESIRED IRULATION TEMPERATURE IS SET. 4. IF UNABLE TO REA DESIRED TEMPERATURE WIT VALVE #1 IN TE FULL OPEN POSITION, OPEN BALANE VALVE #2 IN SMALL INREMENTS (i.e. 1/8, ¼, 3/8, ET) UNTIL DESIRED TEMPERATURE IS AIEVED. REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD, MGR-1). 5
INSTRUTIONS FOR SERVIING LARGER TM22B VALVE INSTRUTIONS FOR SERVIING SMALLER TM22B VALVE M2-2 SREWS LTR SET SREW SREW 1. Loosen LTR set screw. 2. Remove snap cap, screw and washer, friction spring and pointer. 3. Turn off hot and cold supplies at checkstops. Remove TM-16 cover screws to release cover and thermostatic control assembly. 4. To clean port sleeve assembly, (the thimble must move freely on the port sleeve): unscrew the check nut as far as it will go, then screw the port sleeve nut into the base. The port sleeve and thimble may be lifted out. SEE DWG BELOW 5. lean in a non-corrosive cleaning solution. DO NOT USE ABRASIVES! The port sleeve should be reassembled in the valve. TIMBLE TEMPERATURE ADJUSTING SREW TM2-1-12B ONTROL ASSEMBLY M2-3 1. Loosen LTR set set screw. 2. Remove pointer screw, and pointer. 3. Turn off hot and cold supplies at screwdriver checkstops. Remove M2-2 cover screws to release cover and thermostatic control assembly. 4. To remove bridge assembly, TM28-1-8B, remove pointer rod nut (MU-1B) and pull bridge assembly off control rod. 5. To clean submerge bridge assembly in clean water or noncorrosive cleaning solution. DO NOT USE ABRASIVES! Be certain thimble moves freely on port sleeve. Note! Di Drivingi bll ball on thimble must engage coil bracket in assembling. TM-28-1-8B BRIDGE ASSY EK NUT PORT SLEEVE PORT SLEEVE NUT 6. To clean thermostat group, remove coil sleeve stud and take off thermostat group. 7. lean in a non-corrosive cleaning solution. 8. When reassembling, make sure driving ball of thermostat group engages the ball socket of the port sleeve assembly. MU-1B ROD NUT 6. To disassemble bridge assembly, see drawing next page (remove TM25-3A holder nuts with screwdriver in slots provided). 7. To clean thermostat coil, remove retaining ring and stop, loosen gland nut. Push rod through cover. Be careful not to pull coil out of shape. sape. TROUBLESOOTING INSTRUTIONS Note: Provide serial number when ordering parts for each valve! LARGE VALVE SMALL VALVE PAKING & S 1. Leaks at stem. 2. Leak between valve cover and base. Repair Kit # 1/2Y Repair Kit # 1/26 (Packings & Gaskets) PORT SLEEVE/BRIDGE ASSEMBLY 3. Valve delivers either all hot or all cold water, or will not mix consistently. Repair Kit # R/2N Repair Kit #R/28 (Rebuilding Kit) or TM28-1-8B Bridge Assembly TERMOSTAT GROUP 4. After cleaning or replacing port sleeve/ bridge assembly, valve performance is not consistent. Repair Kit # R/2N Repair Kit #R/28 (Rebuilding Kit) or TM-28-G2 Thermostat Group EKSTOPS 5. ot water by-pass into cold line(or cold into hot). 6. Supplies cannot be shut off completely. Supplies leak at checkstop bonnets. Repair Kit #2/2Y Repair Kit #4/M2 (heckstop Kit) 6
TM-22B LARGE VALVE PARTS TM-15B/2 TGM-2/125 TERMOSTAT GROUP 57-L SNAP AP TM-25 TM-25D STOP TM-8 OIL SLEEVE O'RING (2) 3 FRITION TM-28A ROD TM-29/29A SREW W/WASER TM-16A DIAL PLATE TM-16 SREWS TM-21/125 FLANGE PAKING TGM-1/2 PORT SLEEVE ASSY TM-3/2 PORT SLEEVE NUT ASSY TM-16 DIAL PLATE EKSTOP PARTS REPAIR KITS * 477 SWIVEL NUT * 474 SWIVEL 4733 & PAKING/O'RING 4724 4742 YELLOW 4727 UPPER STEM 313 O'RINGS (2) 4728 AP WASER 4723 AP KIT 1/2Y * PAKINGS & S **=2 EA. O'RING** 4742 4733 YELLOW ** & PAKING ** TM-21/125 FLANGE PKG. 4724 SREEN ** 313 UPPER STEM O'RING (4) KIT R/2N * REBUILDING KIT TM-3/2 PORT SLEEVE NUT ASSY. TM-28A ROD ROD O'RING (2) 4728 AP WASER** TM-21/125 FLANGE PKG. (* IF APPLIABLE) TM-8 TGM-1/2 OIL SLEEVE PORT SLEEVE ASSY. KIT 2/2Y * EKSTOP KIT TGM-2/125 TERMOSTAT GROUP LOK-TYPE 2 EA: 313 STEM O'RING (4) 4724 SREEN 4728 AP WASER TM-36 SET SREW 4733 & PAKING 4742 YELLOW REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD) NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT STOP ON EA VALVE (SEE PAGE 2). 7
SMALL TM VALVE PARTS 752 SREW 691 LTR SET SREW 57-D RF GLAND NUT 337 DIAL PLATE M2-1 RF/P M2-3 7628 TM-28-1-8B BRIDGE ASSEMBLY MU-4 GLAND PAKING TM28-G2 TERMOSTAT GROUP MU-1B ROD NUT TM25-3 TM-25-3A PS P.S. OLDER P.S. OLDER NUT TGM-1/28 PORT SLEEVE TM-28-6B ASSEMBLY OLDER NUT O'RING TM25-5 BRIDGE TM25-3B P.S. PA KING EKSTOP PARTS REPAIR KITS EKSTOPS M2-3A BONNET PAKING M2-9A EK M2-6A LOWER STEM & PAKING MU-4A RF UPPER STEM AND PAKING UPPER STEM PKG. M2-2A RF EK BONNET KIT 1/26 PAKINGS & S MU-4 GLAND PKG. (2 EA) M2-3A BONNET PKG. (2 EA) M2-3 M2-9A (2 EA) EK TM-28-6B OLDER NUT O'RING (2 EA) M2-6A & PKG. (2 EA) O'RING (2 EA) REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD) NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT STOP ON EA VALVE (SEE PAGE 2). KIT R/28 REBUILDING KIT M2-3 KIT 4/M2 EKSTOP KIT 2 EA: M2-6A & PAKING M2-9A EK UPPER STEM O'RING TM-28-1-12B ONTROL ASSEMBLY M2-3A BONNET PKG. 8
TM-152A INSTRUTIONS INSTRUTIONS FOR SERVIING LARGER TM152A VALVE DRIVING BALL BALL SOKET INSTRUTIONS FOR SERVIING SMALLER TM152A VALVE LTR SET SREW SREW M2-2 SREWS TERMOSTAT GROUP FLANGE PAKING 1. Loosen LTR set screw. 2. Remove screw, snap cap, and pointer. 3. Turn off hot and cold supplies at screwdriver checkstops. Remove cover screws to release cover and thermostat group. TIMBLE EK NUT TEMPERATURE ADJUSTING SREW TM2-1-12B ONTROL ASSEMBLY M2-3 1. Remove screw and pointer. 2. Loosen LTR set screw. 3. Turn off hot and cold supplies at screwdriver checkstops. Remove M2-2(P) cover screws to release cover and thermostatic control assembly. 4. To remove bridge assembly, M2-1-8B, remove pointer rod nut (MU-1B) and pull bridge assembly off control rod. M2-1-8B BRIDGE ASSY PORT SLEEVE PORT SLEEVE PORT SLEEVE NUT TIMBLE M2-5B P.S. OLDER NUT 4. To clean, port sleeve assembly (the thimble must slide freely on the port sleeve): unscrew the check nut as far as it will go, then screw the port sleeve nut into base. The port sleeve and thimble may then be lifted out. 5. To clean thermostat coil, remove coil sleeve stud and take off thermostat group. 6. lean with a non-corrosive cleaning solution. DO NOT USE ABRASIVES! 7. When reassembling, make sure driving ball of thermostat group engages the ball socket of the port sleeve assembly. MU-1B ROD NUT M2-14B DRIVING 5. To clean, submerge bridge in clean water or non-corrosive cleaning solution. DO NOT USE ABRASIVES! Be certain thimble moves freely on the port sleeve. Note! Driving stud (M2-14B) must engage slot in thimble when reassembling. 6. To clean thermostat coil, remove retaining ring and stop, loosen gland nut. Push rod through cover. Be careful not to pull coil out of shape. 7. lean with a non-corrosive cleaning solution. DO NOT USE ABRASIVES! TROUBLESOOTING INSTRUTIIONS Note: Provide valve serial number when ordering parts for each valve! Large Valve Small Valve PAKING & S 1. Leak at stem 2. Leak between valve cover and base. Repair Kit 1/125Y Repair Kit 1/M2 (Packings & Gaskets) PORT SLEEVE/BRIDGE ASSEMBLY 3. Valve delivers either all hot or all cold water, or will not mix consistently. Repair Kit R/125 Repair Kit R/M2 TM-2 (Rebuilding Kit) or M2-1-8B Bridge Assembly TERMOSTAT GROUP 4. After cleaning or replacing port sleeve/bridge assembly, valve performance is not consistent. Repair Kit R/125 or TGM- 125 Repair Kit R/M2 (Rebuilding Kit) or M2- G2 Thermostat Group EKSTOPS 5. ot water by-pass into cold line (or cold into hot). 6. Supplies cannot be shut off completely. Supplies leak at checkstop bonnets. Repair Kit 2/5Y Repair Kit 4/M2 (heckstop Kit) See pages 1 & 11 for parts Breakdowns 9
TM152A LARGE VALVE PARTS 57-L SNAP AP TM-25 TM-15B/125 TM-25D STOP TGM-2/125 TERMOSTAT GROUP TM-8 OIL SLEEVE O'RING (2) TM-29/29A SREW W/WASER 3 FRITION TM-16 SREWS TM-28A ROD TM-16A/125 DIAL PLATE TM-3/125 PORT SLEEVE NUT ASSY TM21/125 FLANGE PAKING TGM-1/125 PORT SLEEVE ASSY EKSTOP PARTS REPAIR KITS 3 & PAKING 1529 YELLOW 9/125 SWIVEL NUT 4/125 SWIVEL UPPER STEM 1 O'RING 13 SREEN 5 BONNET PAKING TM-2 BONNET 14 AP PAKING 6 STRAINER AP REPAIR KIT 1/125Y PAKINGS & S **=2 EA. O'RING (4) 1529 ** 3** YELLOW & PAKING TM21/125 FLANGE PKG 13** SREEN REPAIR KIT R/125 TM-152A REBUILDING KIT 5** BONNET PKG. 14** AP PAKING LOK-TYPE TM-3/125 PORT SLEEVE NUT ASSY. TM-28A ROD O'RING (2) TM21/125 FLANGE PKG TM-36 SET SREW TGM-1/125 PORT SLEEVE ASSY TGM-2/125 TERMOSTAT GROUP TM-8 OIL SLEEVE REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. SEE MAINTENANE GUIDE AND REORD MGR-11. NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT STOP ON EA VALVE (SEE PAGE 8). REPAIR KIT 2/5Y EKSTOP KIT 2 EA: 3 & PAKING O'RING 13 SREEN 5 BONNET PKG. 1529 14 YELLOW AP PAKING 1
TM152A SMALL VALVE PARTS 752 SREW 691 LTR SET SREW 57-D(RF) GLAND NUT 335 DIAL PLATE M2-1(RF)(P) M2-3 7628 MU-4 GLAND PAKING M2-14B DRIVING M-2-1-8B BRIDGE ASSEMBLY EKSTOP PARTS M2-G2 TERMOSTAT GROUP R DURA-trol MU-1B ROD NUT M2-4B P.S. OLDER M2-5B P.S. OLDER NUT M2-G1 PORT SLEEVE ASSEMBLY M2-6B OLDER NUT O'RING M2-1B BRIDGE M2-3B P.S. PAKING M2-14B DRIVING REPAIR KITS EKSTOPS M2-3A BONNET PAKING M2-9A EK M2-6A LOWER STEM & PAKING MU-4A RF UPPER STEM AND PAKING UPPER STEM PKG. M2-2A RF EK BONNET REPAIR KIT 1/M2 PAKINGS & S MU-4 GLAND PKG. (2 EA) M2-9A EK (2 EA) M2-3A BONNET PKG. (2 EA) M2-3 M2-6A & PKG. (2 EA) M2-6B OLDER NUT O'RING (2 EA) O'RING (2 EA) REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD) NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT STOP ON EA VALVE (SEE PAGE 2). REPAIR KIT R/M2 REBUILDING KIT M2-3 M2-1-12B ONTROL ASSEMBLY REPAIR KIT 2/M2 PORT SLEEVE KIT M2-3B P.S. PAKING (2 EA) M2-G1 PORT SLEEVE ASSY. M2-6B OLDER NUT O'RING (2 EA) REPAIR KIT 4/M2 EKSTOP KIT M2-6A M2-3A BONNET PKG. & PKG. (2 EA) (2 EA) M2-9A EK (2 EA) O'RING (2 EA) 11
4 2 2 3 1 R -1 F 8 5 14 4 1 12 OPTIONAL OUTLET SETUP PIPING (BY OTERS) The addition of this piping arrangement (extra tee and ball valve) eliminates the need to turn fixtures on and off throughout the building at setup. The flows required in the setup instructions (page 3) are set by using Ball Valve A. (make sure main outlet ball valve is closed). MAIN OUTLET BALL VALVE TEMPERED WATER TO BUILDING BALL VALVE A AUTION! ALL WATER MIXING VALVES AND SYSTEMS AVE LIMITATIONS! TEY WILL NOT PROVIDE TE DESIRED PERFORMANE OUTSIDE OF TEIR FLOW APAITY RANGE! ONSULT TE APAITY ART BELOW AND OBSERVE MINIMUM FLOWS SOWN. FLOW APAITIES DOUBLE FLOWRATE WEN BOT VALVES ARE OPERATING SINGLE VALVE ASSEMBLY FLOWRATES SOWN (MINIMUM FLOW RATE AS BEEN DOUBLED TO 2GPM) TM-152A-2P PARALLEL MINIMUM FLOW (GPM) (l/min) 5.3 SYSTEM PRESSURE DROP (PSIG) 1 15 2 25 3 35 4.7.97 1.4 1.7 2.1 2.4 2.8 2. 48 65 8 95 8 182 273 333 3 112 12 424 454 492 13 14 53 45 5 3.1 3.4 158 165 598 625 PSI BAR GPM l/min TM-22B-2P PARALLEL MINIMUM FLOW (GPM) (l/min) 5.3 SYSTEM PRESSURE DROP (PSIG) 1 15 2 25 3 35 4.7.97 1.4 1.7 2.1 2.4 2.8 2. 78 113 129 145 8 295 428 488 549 163 172 617 651 712 188 197 746 45 5 3.1 3.4 214 226 81 856 PSI BAR GPM l/min LIMITED WARRANTY Leonard Valve ompany (hereinafter, Leonard ) warrants the original purchaser that products manufactured by Leonard will be free from defects in material or workmanship under normal conditions of use, when properly installed and maintained in accordance with Leonard s instructions, for a period of one year from the date of shipment. During this period, Leonard will at its option repair or replace any product, or part thereof, which shall be returned, freight prepaid, to the Leonard factory and determined by Leonard to be defective in materials or workmanship. Leonard provides no warranty, express or implied, which extends beyond the description contained herein. SPEIFIALLY DISLAIMS ANY AND ALL IMPLIED WARRANTIES OF MERANTABILITY OR OF FITNESS FOR A PARTIULAR PURPOSE. Nonetheless, some jurisdictions may not allow the disclaimer of certain implied warranties, in which case Leonard hereby limits such implied warranties to the duration of the limited warranty period contained herein. Some jurisdictions may not allow limitations on how long an implied warranty lasts, so the foregoing durational limitation may not apply to you. In no event will Leonard be liable for labor or incidental or consequential damages. Any alteration or improper installation or use of this product will void this limited warranty. If any provision of this limited warranty is prohibited by law in the applicable jurisdiction, such provision shall be null and void, but the remainder of this limited warranty shall continue in full force and effect. 214 Leonard Valve ompany Printed in USA