THE WALL-MOUNT AIR CONDITIONER -. EER, (HZ) Models WAA to W72AA Right-ide Control Panel Models WLA to W72LA Left-ide Control Panel. to Ton (7, to 7, Btuh) Green Refrigerant R-A The Bard Wall-Mount Air Conditioner is a self contained energy efficient system, which is designed to offer maximum indoor comfort at a minimal cost without using valuable indoor floor space or outside ground space. This unit is the ideal product for versatile applications such as: new construction, modular offices, school modernization, telecommunication structures, portable structures or correctional facilities. Factory or field installed accessories are available to meet specific job requirements. Engineered Features Aluminum Finned Copper s: Grooved tubing and enhanced louvered fin for maximum heat transfer and energy efficiency. Twin Blowers: Move air quietly. Most models feature multispeed blower motors providing airflow adjustment for high and low static operation. Motor overload protection is standard on all models. Air Conditioner Compressor: croll Compressors eliminate need for crankcase heater. tandard on all models, except -Ton. R-A Refrigerant: Designed with R-A (HFC) non-ozone depleting refrigerant in compliance with the Montreal protocol and 2 EPA requirements. Phase Rotation Monitor: tandard on all 3-phase scroll compressors. Protects against reverse rotation if power supply is not properly connected. Rotation protection is not required on the -Ton Unit(s). Galvanized 2 Gauge Zinc Coated teel Cabinet: Cleaned, rinsed, sealed and dried before the polyurethane primer is applied. The cabinet is handsomely finished with a baked on textured enamel, which allows it to withstand hours of salt spray tests per ATM B7-3. Foil Faced Insulation: tandard on all units. Full Length Mounting Brackets: Built into cabinet for improved appearance and easy installation. NOTE: Bottom mounting bracket included to assist in installation. Electrical Components: Are easily accessible for routine inspection and maintenance through a right side, service panel opening. Features a lockable, hinged access cover to the circuit breaker or toggle disconnect switch. Electric Heat trips: Features an automatic limit and thermal cut-off safety control. Heater packages can be factory or field installed. Filter ervice Door: eparate service door provides easy access for filter change. One Inch, Disposable Air Filters: Are standard equipment. Optional one inch washable filters available and filter racks permit the addition of 2" pleated filter. Factory or field installed. Condenser Fan and Motor hroud Assembly: lides out for easy access. Barometric Fresh Air Damper: tandard on all units. Allows up to 2% outside fresh air. Optional ventilation packages available. Built-in Circuit Breakers: tandard on all electric heat versions of single (23/2 volt) and three phase (23/2 volt) equipment. Toggle disconnects are standard on all electric heat versions of three phase ( volt) equipment. lope Top: tandard feature for water run-off. Top Rain Flashing: tandard feature on all models. Freezestat: tandard on W72 models. Optional field installed CMC-2 can be used on all other models. Liquid Line Filter Drier: tandard on all units. Protects system against moisture. Compressor Control Module: tandard on all units. Built-in offdelay timer adjustable from 3 seconds to minutes. 2-minute on-delay if power interrupt. 2-second bypass for low pressure control, and both soft and manual lockouts for high and low pressure controls. Alarm output for alarm relay. High & Low Pressure witches are Auto- Reset: tandard on all units. Built-in lockout circuit resets from the room thermostat. Provides commercial quality protection to the compressor. Complies with efficiency requirements of AHRAE/IENA.-23. Certified to ANI/ARI tandard 3-23 for PVU (ingle Package Vertical Units). Intertek ETL Listed to tandard for afety Heating and Cooling Equipment ANI/UL /CA 22.2 No. 23-, Fourth Edition. Commercial Product - Not intended for Residential application. Form No. 2-2 upersedes 2- Page of
Capacity and Efficiency Ratings Models WAA WLA W2AA W2LA W3AA W3LA W3AA W3LA Capacity is certified in accordance with ANI/ARI tandard 3-23. EER = Energy Efficiency Ratio and is certified in accordance with ANI/ARI tandard 3-23. All ratings based on fresh air intake being % closed (no outside air introduction). W2AA W2LA WAA WLA WAA WLA W72AA W72LA Cooling Capacity BTUH 7, 2, 3, 3,,,, 7, EER..2.3..... pecifications -/2 Ton through 3 Ton MODEL WAA-A WLA-A W2AA-A W2LA-A W2AA-B W2LA-B W2AA-C W2LA-C W3AA-A W3LA-A W3AA-B W3LA-B W3AA-C W3LA-C W3AA-A W3LA-A W3AA-B W3LA-B W3AA-C W3LA-C Electrical Rating Hz 23/2-23/2-23/2-3 - 3 23/2-23/2-3 - 3 23/2-23/2-3 - 3 Operating Voltage Range 7-23 7-23 7-23 - 7-23 7-23 - 7-23 7-23 - Compressor--Circuit A Voltage 23/2 23/2 23/2 23/2 23/2 23/2 23/2 Rated Load Amps./..2/../..3./2../7. 3. 3././.. Branch Circuit election Current. 2..3....7 7. 3.2. Lock Rotor Amps / / / 2 77/77 7/7 3 2/2 / Compressor Type croll croll croll croll croll croll croll croll croll croll Fan Motor & Condenser Fan Motor--HP--RPM / - / - / - / - / - / - / - / - / - / - Fan Motor--Amps.2.2.2....... Fan--DIA/CFM " - " - " - " - 2" - 2 2" - 2 2" - 2 2" - 22 2" - 22 2" - 22 Blower Motor & Evap. Blower Motor--HP-RPM-PD /--2 /-- /-- /-- /3--2 /3--2 /3--2 /3--2 /3--2 /3--2 Blower Motor--Amps.... 2. 2.. 2. 2.. Motor Type PC PC PC PC PC PC PC PC PC PC CFM Cooling & E..P. w/filter (Rated- ) -. -.3 -.3 -.3 -. -. -. -.3 -.3 -.3 Filter izes (inches) TD. x2x x2x x2x x2x x3x x3x x3x x3x x3x x3x hipping Weight --LB. 33 32 32 32 3 3 3 pecifications 3-/2 Ton through Ton MODEL W2AA-A W2LA-A W2AA-B W2LA-B W2AA-C W2LA-C WAA-A WLA-A WAA-B WLA-B WAA-C WLA-C WAA-A WLA-A WAA-B WLA-B WAA-C WLA-C W72AA-A W72LA-A W72AA-B W72LA-B W72AA-C W72LA-C Electrical Rating Hz 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 Operating Voltage Range 7-23 7-23 - 7-23 7-23 - 7-23 7-23 - 7-23 7-23 - Compressor--Circuit A Voltage 23/2 23/2 23/2 23/2 23/2 23/2 23/2 23/2 Rated Load Amps./../..2 7.3/../3.3. 2./23.2 3./. 7. 27.7/3../.. Branch Circuit election Current. 3.. 2...3 23.2. 7. 3. 22.. Lock Rotor Amps / 3./3. / / 3/3 / / / Compressor Type croll croll croll croll croll croll Recip. Recip. Recip. croll croll croll Fan Motor & Condenser Fan Motor--HP--RPM-PD /3-2-2 /3-2-2 /3-2- /3-2-2 /3-2-2 /3-2- /3-2-2 /3-2-2 /3-2- /2-- /2-- 3/-- Fan Motor--Amps 2. 2..3 2. 2..3 2. 2..3...7 Fan--DIA/CFM 2" - 2 2" - 2 2" - 2 2" - 3 2" - 3 2" - 3 2" - 3 2" - 3 2" - 3 2" - 2" - 2" - Blower Motor & Evap. Blower Motor--HP-RPM-PD /3--2 /3--2 /3--2 /3--2 /3--2 /3--2 /2-7-2 /2-7-2 /2-7-2 3/--2 3/--2 3/--2 Blower Motor--Amps 2.3 2.3.2 2.3 2.3.2 3. 3. 2..3.3.7 Motor Type PC PC PC PC PC PC PC PC PC ECM ECM ECM CFM Cooling & E..P. -. -. -. -. -. -. -.3 -.3 -.3 -.2 -.2 -.2 w/filter (Rated- ) Filter izes (inches) TD. 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x 2x3x hipping Weight --LB. Form No. 2-2 upersedes 2- Page 2 of
Ventilation ystem Packages Bard Wall-Mounts are designed to provide optional ventilation packages to meet all of your ventilation and indoor air quality requirements. All units are equipped with a barometric fresh air damper as the standard ventilation package. All ventilation packages can be built-in at the factory or field-installed at a later date. BAROMETRIC FREH AIR DAMPER - WBFAD TANDARD The barometric fresh air damper is a standard feature on all models. It is installed on the inside of the service door and allows outside ventilation air, up to 2% of the total airflow rating of the unit, to be introduced through the air inlet openings and to be mixed with the conditioned air. The damper opens during blower operation and closes when the blower is off. Adjustable blade stops allow different amounts of outside air to be introduced into the building and can be easily locked closed if required. MI-3 Barometric Fresh Air Damper BLANK OFF PLATE - WBOP OPTIONAL A blank off plate is installed on the inside of the service door. It covers the air inlet openings, which restricts any outside air from entering the unit. The blank off plate should be utilized in applications where outside air is not required to be mixed with the conditioned air. MOTORIZED FREH AIR DAMPER - WMFAD OPTIONAL The motorized fresh air damper is internally mounted behind the service door and allows outside ventilation air, up to 2% of the total airflow rating of the unit, to be introduced through the air inlet openings and to be mixed with the conditioned air. The two position damper can be fully open or closed. The damper blade is powered open by a 2VAC motor with spring return on power loss. The damper can be controlled by indoor blower operation or can be field connected to be managed based on building occupancy. NOTE: The above vent systems are intake only without built-in exhaust capability. Building will likely require separate field installed barometric relief or mechanical exhaust elsewhere within the conditioned space. Balancing dampers in the return air grille may be required to achieve specified amount of outdoor air intake. Motorized Fresh Air Damper Commercial Room Ventilator Economizer Energy Recovery Ventilator MI-3 MI-3 MI-3 MI-37 COMMERCIAL ROOM VENTILATOR - WCRV OPTIONAL The built-in commercial room ventilator is internally mounted behind the service door and allows outside ventilation air, up to % of the total airflow rating of the unit. It includes a built-in exhaust air damper for room pressurization relief. The commercial room ventilator (CRV) is a simple and innovative approach to improving the indoor air quality by providing fresh air intake and exhaust capability through the CRV. The damper can be easily adjusted to control the amount of fresh air supplied into the building. The CRV can be controlled by indoor blower operation or field controlled based on room occupancy. Two versions available (except on. and 2-Ton models). The CRV and CRV are power open - spring return on power loss, with positive shut-off. Complies with ANI/AHRAE tandard 2. Ventilation for Acceptable Indoor Air Quality. tandard Features: Fully modulating Honeywell Hi-Torque Actuator with -V signal input capability 7" intake hood with filter imple single blade design Positive shut-off with non-stick gaskets olid tate Controller with occupancy CFM setting and modulating -2 ma thermostat signal input ECONOMIZER WECO eries OPTIONAL The built-in economizer is internally mounted behind the service door and allows outside ventilation air, up to % of the total airflow rating of the unit. It includes a built-in exhaust air damper for room pressurization relief. The economizer is designed to provide free cooling when outside air conditions are cool and dry enough to satisfy cooling requirements without running the compressor. This in turn provides lower operating costs, while extending the life of the compressor. tandard Features: Full rated outdoor intake Fully modulating Honeywell Hi-Torque Actuator 7" intake hood with filter imple single blade design Positive shut-off with non-stick gaskets Electronic DB and/or Enthalpy sensors depending upon version Honeywell JADE electronic economizer module with precision settings and diagnostics DB or Enthalpy economizer versions available WALL-MOUNT ENERGY RECOVERY VENTILATOR - WERVP OPTIONAL The wall-mount energy recovery ventilator (ERV) is a highly innovative approach to meeting indoor air quality ventilation requirements as established by ANI/AHRAE tandard 2.. The ERV allows from 2 to CFM (depending upon model) of fresh air and exhaust through the unit while maintaining superior indoor comfort and humidity levels. In most cases this can be accomplished without increasing equipment sizing or operating costs. Heat transfer efficiency is up to 7% during summer and % during winter conditions. The ERV consists of a unique rotary energy recovery cassette that provides effective sensible and latent heat transfer capabilities during summer and winter conditions. Various control schemes are addressed including limiting ventilation during building occupancy only. The ERV is designed to be internally mounted behind the service door in the W**A or W**L model wall-mount units. It can be built-in at the factory (W**A only) or field installed as an option. ERVP-*3 and ERVP-* can be independently adjusted for intake and exhaust rates. The ERV s have exhaust gravity shut-off dampers and motorized air intake dampers for positive shut-off. Wiring includes plug-in harnesses for easy vent installation and removal. Form No. 2-2 upersedes 2- Page 3 of
Commercial Room Ventilator Performance Data - WCRV-2 W & W2 Ventilation Delivery 7 Ventilation CFM 3 2 2 3 7 Damper Position upply & Return Grilles.2" Duct tatic." Duct tatic Commercial Room Ventilator Performance Data - WCRV-3 and WCRVP-3 2 W3 & W3 Ventilation Delivery Ventilation CFM 2 2 3 7 Damper Position upply & Return Grilles.2" Duct tatic." Duct tatic Form No. 2-2 upersedes 2- Page of
Commercial Room Ventilator Performance Data - WCRV- and WCRVP- 2 W2 & W Ventilation Delivery Ventilation CFM 2 2 3 7 Damper Position upply & Return Grilles.2" Duct tatic." Duct tatic W Ventilation Delivery Ventilation CFM 2 2 2 3 7 Damper Position upply & Return Grilles.2" Duct tatic." Duct tatic W72 Ventilation Delivery Ventilation CFM 2 2 2 3 7 Damper Position upply & Return Grilles.2" Duct tatic." Duct tatic Form No. 2-2 upersedes 2- Page of
Performance and Application Data- WERVP-A2 Ambient O.D. VENTILATION RATE -- 2 CFM 2% EFFICIENCY UMMER COOLING PERFORMANCE (INDOOR DEIGN CONDITION DB/2 WB) VENTILATION RATE -- 22 CFM 3% EFFICIENCY VENTILATION RATE -- 2 CFM 3% EFFICIENCY DB/WB F VLT VL VLL HRT HR HRL VLT VL VLL HRT HR HRL VLT VL VLL HRT HR HRL 7 7 7 7 7 7 7 2 2 3 2 3 2 3 2 3 27 27 2 3 233 3 233 27 27 27 27 27 32 3 2 2 3 7 23 22 3 3 3 3 233 73 22 22 73 2 73 2 33 33 73 2 2 2 73 2 7 7 73 2 37 2 22 22 22 33 33 33 33 33 2 2 2 2 2 7 7 7 7 7 37 37 37 37 22 32 7 33 7 37 3 7 27 72 2 7 3 2 2 727 727 727 7 727 73 72 72 7 727 73 7 727 73 33 33 7 727 73 22 22 727 73 22 2 73 22 727 727 727 72 72 72 72 72 33 33 33 33 33 22 22 22 22 22 2 2 2 2 3 7 3 7 2 7 23 3 2 37 3 73 22 3 32 32 3 3 3 3 22 22 3 3 3 3 33 33 32 32 32 32 32 3 3 3 3 3 22 22 22 22 22 3 3 3 3 3 2 2 233 3 2 3 22 2 3 32 7 3 33 32 32 32 32 2 2 32 32 32 32 32 32 32 32 32 32 2 2 2 2 2 3 72 22 7 3 22 73 33 2 2 3 32 32 3 2722 2722 3 2 2 3 3 3 3 3 2 2 2 32 32 32 32 32 2722 2722 2722 2722 2722 2 2 2 2 2 3 3 3 3 3 2 3 2 2 32 737 3 7 7 2 33 277 3 Ambient O.D. WERVP-A2 WINTER HEATING PERFORMANCE (INDOOR DEIGN CONDITION 7 F DB) VENTILATION RATE 2 2 CFM 7% EFF. 22 CFM % EFF. 2 CFM % EFF. DB/ F WVL WHR WVL WHR WVL WHR 2 27 22 22 2 2 27 33 2733 32 23 3 33 32 32 72 727 3 37 7 3 72 7 727 2 2 3 72 72 2 2 3 NOTE: ensible performance only is shown for winter application. LEGEND: VLT = Ventilation Load - Total VL = Ventilation Load - ensible VLL = Ventilation Load - Latent HRT = Heat Recovery - Total HR = Heat Recovery - ensible HRL = Heat Recovery - Latent WVL = Winter Ventilation Load WHR = Winter Heat Recovery Form No. 2-2 upersedes 2- Page of
Performance and Application Data- WERVP-*3 Performance and Application Data- WERVP-* UMMER COOLING PERFORMANCE (INDOOR DEIGN CONDITION DB/2 WB) UMMER COOLING PERFORMANCE (INDOOR DEIGN CONDITION DB/2 WB) VENTILATION RATE -- 2 CFM % EFFICIENCY VENTILATION RATE -- 32 CFM % EFFICIENCY VENTILATION RATE -- CFM 3% EFFICIENCY Ambient O.D. VENTILATION RATE -- 2 CFM % EFFICIENCY VENTILATION RATE -- 32 CFM % EFFICIENCY VENTILATION RATE -- CFM 3% EFFICIENCY Ambient O.D. F VLT VL VLL HRT HR HRL VLT VL VLL HRT HR HRL VLT VL VLL HRT HR HRL DB/ WB F VLT VL VLL HRT HR HRL VLT VL VLL HRT HR HRL VLT VL VLL HRT HR HRL DB/ WB 3 2 2 2 7 2 2 72 72 72 3 72 72 37 737 2 2 2 77 2 2 77 77 77 2 77 77 2 7 2 2 2 2 7 2 2 32 2 32 73 73 73 2 73 73 72 3 3 3 2 3 3 22 2 2 2 2 2 2 7 3 27 27 27 27 27 7 7 27 27 2 2 7 333 73 2 3 2 2 23 37 37 37 37 37 7 7 37 37 2 2 2 2 2 2 737 73 2 2 2 772 2 2 3 2 2 2 2 2 232 77 23 2 2 2 3 2 7 727 77 77 77 77 77 233 2 2 77 77 3 22 7 7 7 7 7 22 2 2 7 7 2 3 2 2 2 2 2 2 22 2 2 7 7 22 77 72 2 2 7 7 2 3 3 3 3 3 7 7 3 3 73 77 2 2 3 2 22 7 7 7 2 2 2 3 3 3 3 3 737 73 3 3 22 77 23 2 2 2 2 232 77 23 2 73 7 2 2 2 2 2 2 7 2 2 2 3 3 3 3 3 233 2 2 3 3 27 7 232 72 72 72 72 72 22 2 2 72 72 227 77 7 72 72 72 72 72 2 22 72 72 7 3 3 3 3 3 7 22 7 3 3 23 2 7 33 22 32 32 32 32 32 7 7 32 32 2 33 77 2 2 3 2 3 77 27 232 232 232 232 232 7 7 232 232 7 22 737 73 22 2 2 2 2 232 2 23 232 77 23 7 23 32 33 33 33 33 33 2 7 33 33 237 73 73 73 73 73 233 2 2 73 73 23 2 2 2 2 2 2 22 2 2 2 2 3 73 2 72 72 72 72 72 2 22 72 72 7 2 2 2 2 2 7 22 7 2 2 2 2 2 7 3 7 33 27 27 27 27 27 7 7 27 27 72 7 2 2 32 32 32 32 32 2 3 2 32 32 7 32 2 7 7 22 2 272 272 272 272 272 737 73 272 272 222 337 23 27 27 27 27 27 2 2 27 27 2 7 33 232 77 23 737 73 7 22 22 22 22 22 2 7 22 22 2 233 2 2 273 72 22 2 2 2 2 22 7 272 272 272 272 272 7 22 7 272 272 237 7 32 32 32 32 32 2 32 32 7 2 32 2 2 7 2 2 2 2372 22 22 73 3 77 77 77 77 7 77 2 2 2 2 232 7 2 23 23 23 23 2 7 23 377 7 3 2 2 37 2 3 3 3 3 22 7 23 3 2 2 2 2 2 2 2 37 2 7 7 7 2 2 2 2 3 2 2 2 33 33 33 33 73 233 33 22 22 22 22 77 23 3 22 2 2 27 7 23 23 23 23 2 22 22 23 7 7 7 2 2 2 2 73 233 73 233 23 3 23 3 2 27 2 27 22 22 22 22 2 232 2 232 7 7 2 37 2 37 7 23 7 23 37 37 7 7 WERVP-* WINTER HEATING PERFORMANCE (INDOOR DEIGN CONDITION 7 F DB) WERVP-*3 WINTER HEATING PERFORMANCE (INDOOR DEIGN CONDITION 7 F DB) VENTILATION RATE VENTILATION RATE 3 CFM 2% EFFICIENCY 3 CFM % EFFICIENCY CFM % EFFICIENCY Ambient O.D. 2 CFM 77% EFFICIENCY 32 CFM 7% EFFICIENCY CFM % EFFICIENCY Ambient O.D. DB/ F WVL WHR WVL WHR WVL WHR 23 22 2 32 3 32 32 2 72 32 2 72 777 33 2 72 2 2 2 2 72 77 7 3 3 2 3 2 2 322 2 27 2 27 7 22 72 2 23 22 2 2 32 273 23 222 2 72 2 NOTE: ensible performance only is shown for winter application. LEGEND: VLT = Ventilation Load - Total VL = Ventilation Load - ensible VLL = Ventilation Load - Latent HRT = Heat Recovery - Total HR = Heat Recovery - ensible HRL = Heat Recovery - Latent WVL = Winter Ventilation Load WHR = Winter Heat Recovery DB/ F WVL WHR WVL WHR WVL WHR 2 2 333 3 32 32 27 27 27 2 3 72 3 7 7 2 72 3 2 237 2 3 22 33 727 3 72 2 7 3 2 2 2 2 2 2 333 237 72 7 3 NOTE: ensible performance only is shown for winter application. Form No. 2-2 upersedes 2- Page 7 of
Electrical pecifications W**AA eries MODEL WAA-A,AZ A A A W2AA-A, AZ A A A A W2AA-B, BZ Rated Volts & Phase 23/2-23/2- Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors. Based on C copper wire. All wiring must conform to the National Electrical Code and all local codes. These Minimum Circuit Ampacity values are to be used for sizing the field power conductors. Refer to the National Electrical code (latest version), Article 3 for power conductor sizing. Caution: When more than one field power circuit is run through one conduit, the conductors must be derated. Pay special attention to note of Table 3 regarding Ampacity Adjustment Factors when more than three (3) current carrying conductors are in a raceway. IMPORTANT: While this electrical data is presented as a guide, it is important to electrically connect properly sized over-current protection and conductor wires in accordance with the National Electrical Code and all local codes. Form No. 2-2 upersedes 2- Page of No. Field Power Circuits B 23/2-3 W2AA-C, CZ -3 C W3AA-A, AZ A A 23/2- A A or 2 W3AA-B, BZ B B B W3AA-C, CZ C C C2 C W3AA-A, AZ A A A A W3AA-B, BZ B B B W3AA-C, CZ C C C2 C W2AA-A, AZ A A A A2 W2AA-B, BZ B B B W2AA-C, CZ C C WAA-A, AZ A A A A2 WAA-B, BZ B B B WAA-C, CZ C C WAA-A, AZ A A A A2 WAA-B, BZ B B B WAA-C, CZ C C W72AA-A, AZ A A A A2 W72AA-B, BZ B B B W72AA-C, CZ C C 23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 or 2 or 2 or 2 or 2 or 2 or 2 or 2 2 or 2 or 2 or 3 2 Minimum Circuit Ampacity 3 2 2 3 22 2 32 7 2 33 2 7 2 2 2 32 7 23 2 33 2 7 2 2 32 32 2 33 2 7 2 3 3 2 33 2 7 2 3 3 2 27 3 27 2 27 ingle Circuit Maximum External Fuse or Ckt. Brkr. 2 3 3 3 3 2 2 2 2 2 2 3 3 3 2 2 3 2 2 3 2 2 3 2 2 2 3 7 2 2 2 3 Field Power Wire ize 2 2 2 2 2 2 2 2 2 3 2 2 2 3 2 Ground Wire Multiple Circuit Minimum Maximum Circuit External Fuse Field Power Ground Ampacity or Ckt. Breaker Wire ize Wire ize Ckt. A Ckt. B Ckt. C Ckt. A Ckt. B Ckt. C Ckt. A Ckt. B Ckt. C Ckt. A Ckt. B Ckt. C 2 2 2 3 2 2 2 3 2 2 2 2 2 2 2 2 2 3 3 3 2 3 2 2 2 3 2 2 2 2 3
Electrical pecifications W**LA eries MODEL WLA-A,AZ A A A W2LA-A, AZ A A A W2LA-B, BZ Rated Volts & Phase 23/2-23/2- No. Field Power Circuits B 23/2-3 W2LA-C, CZ -3 C W3LA-A, AZ A A 23/2- A A or 2 W3LA-B, BZ B B W3LA-C, CZ C C W3LA-A, AZ A A A W3LA-B, BZ B B W3LA-C, CZ C C W2LA-A, AZ A A A W2LA-B, BZ B B W2LA-C, CZ C C WLA-A, AZ A A A WLA-B, BZ B B WLA-C, CZ C C WLA-A, AZ A A A WLA-B, BZ B B WLA-C, CZ C C W72LA-A, AZ A A A W72LA-B, BZ B B W72LA-C, CZ C C 23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 23/2-23/2-3 -3 or 2 or 2 or 2 or 2 or 2 or 2 Minimum Circuit Ampacity 3 2 3 22 2 32 7 33 7 2 2 32 23 33 7 2 32 32 2 33 2 7 2 3 3 2 33 2 7 2 3 3 27 3 27 2 27 ingle Circuit Maximum External Fuse or Ckt. Brkr. 2 3 3 3 2 2 2 2 3 3 2 3 2 3 2 3 2 2 3 7 2 2 3 Field Power Wire ize 2 2 2 2 2 2 2 3 2 2 3 Ground Wire Dual Circuit Minimum Maximum Circuit External Fuse Field Power Ground Ampacity or Ckt. Breaker Wire ize Wire ize Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B 2 2 2 3 2 2 2 3 2 2 3 2 2 3 2 2 3 2 2 Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors. Based on C copper wire. All wiring must conform to the National Electrical Code and all local codes. These Minimum Circuit Ampacity values are to be used for sizing the field power conductors. Refer to the National Electrical code (latest version), Article 3 for power conductor sizing. Caution: When more than one field power circuit is run through one conduit, the conductors must be derated. Pay special attention to note of Table 3 regarding Ampacity Adjustment Factors when more than three (3) current carrying conductors are in a raceway. IMPORTANT: While this electrical data is presented as a guide, it is important to electrically connect properly sized over-current protection and conductor wires in accordance with the National Electrical Code and all local codes. 2 2 3 Form No. 2-2 upersedes 2- Page of
Indoor Blower Performance ( Hz) - CFM at Rated Voltage peed W W2 W3 W3 W2 W W W72 High Low ingle High Low High Low High Low High Low High Low High Medium Low EP (Inch H2). 72 72 3 3 3 2 7 2 2 22 2 2 2 3. 7 2 32 3 2 3 2 3 7 2 2 2 2 7.2 7 2 2 2 2 7 2 77 7 2 2 2.3 2 22 7 3 72 2 3 22 2 7. 7 72 2 3 2 3 32 7 22 2 7 72. 2 2 7 3 2 3 7 2 72 Above data is with " standard throwaway filter and " washable filter. For optional 2" pleated filter - reduce EP by. in. ee installation instructions for maximum EP information on various KW application. Factory Connected peed. Electric Heat Table - Refer to Electrical pecifications for Availability by Unit Model Nominal KW Kw At 2V () At 2V () At V (2) At V (2) -Ph Amps 3-Ph Amps Btuh Kw -Ph Amps 3-Ph Amps Btuh Kw 3-Ph Amps Btuh Kw 3-Ph Amps Btuh...7 3,2 3..,23.. 2. 7, 3.. 2,7... 2,7. 2.,. 7.2 2,7.2.,.. 33.3 27,3. 2. 2,7.. 2.7 3,77..7 23,3.. 3,77.2. 2,2...7 3,3 7. 3. 2,.. 2. 3.,.2. 3.2 3,3.., 3. 7.3 7,.. 3.3,3 3. 37.,7. 2.7,3. 2., 2. 2. 3.3,2. 72., () These electric heaters are available in 23/2V units only. (2) These electric heaters are available in V units only. Form No. 2-2 upersedes 2- Page of
Heater Packages - Field Installed "A" eries Right-Hand Units Designed for adding Electric Heat to KW Units ETL U & Canada Listed Circuit Breaker tandard on 23/2V Models Toggle Disconnect tandard on V Models Air Conditioner -A Models 23/2- -B Models 23/2-3 -C Models -3 Models Heater Model # KW Heater Model # KW Heater Model # KW WAA EHW2TA-A EHW2TA-A EHW2TA-A W2AA EHWA2-AB EHW2TA-A EHW2TA-A EHW2TA-A EHW2TA-B EHWH2B-C W3AA EHW3TA-A EHW3TA-A EHW3TA-A EHW3TA-A EHW3A-B EHW3TA-B EHW3TA-B EHW3TA-C EHW3TA-C EHW3TA-C2 EHW3TA-C 2 W3AA EHW3TA-A EHW3TA-A EHW3TA-A EHW3TA-A EHW3TA-B EHW3TA-B EHW3TA-B EHW3TA-C EHW3TA-C EHW3TA-C2 EHW3TA-C 2 W2AA WAA EHWTA-A EHWA-AB EHWA-AB EHWA-A2B 2 EHWA-BB EHWA-BB EHWTA-B EHWTA-C EHWTA-C WAA EHWTA-A EHWA-AB EHWA-AB EHWA-A2B 2 EHWA-BB EHWA-BB EHWTA-B EHWTA-C EHWTA-C W72AA EHWTA-A EHW72A-AB EHW72A-AB EHW72A-A2B 2 EHW7A-BB EHWA-BB EHWTA-B EHWTA-C EHWTA-C These heater packages approved for use in dehumidification versions with hot gas reheat. Heater Packages - Field Installed "L" eries Left-Hand Units Air Conditioner Models -A Models 23/2- -B Models 23/2-3 -C Models -3 Heater Model # KW Heater Model # KW Heater Model # KW WLA EHW2TA-AL EHW2TA-AL EHW2TA-AL W2LA EHW2TA-AL EHW2TA-AL EHW2TA-AL EHW2TA-BL W3LA EHW3TA-AL EHW3TA-AL EHW3TA-AL EHW3TA-AL EHW3TA-BL EHW3TA-BL EHW3TA-CL EHW3TA-CL W3LA EHW3TA-AL EHW3TA-AL EHW3TA-AL EHW3TA-BL EHW3TA-BL EHW3TA-CL EHW3TA-CL W2LA WLA EHWTA-AL EHWA-ALB EHWA-ALB EHWA-BLB EHWA-BLB EHWTA-CL EHWTA-CL WLA EHWTA-AL EHWA-ALB EHWA-ALB EHWA-BLB EHWA-BLB EHWTA-CL EHWTA-CL W72LA EHWTA-AL EHW72A-ALB EHW72A-ALB EHW7A-BLB EHWA-BLB EHWTA-CL EHWTA-CL Form No. 2-2 upersedes 2- Page of
Clearances Required for ervice Access and Adequate Condenser Inlet Airflow MODEL LEFT IDE RIGHT IDE WAA, W2AA, W3AA, W3AA " 2" W2AA, WAA, WAA, W72AA 2" 2" NOTE: For side-by-side installation of two (2) WA models, there must be 2" between units. This can be reduced to " by using a WL model (left side compressor and controls) for the left unit and WA (right side compressor and controls) for right unit. Minimum Clearances Required to Combustible Materials MODEL UPPLY AIR DUCT FIRT THREE FEET CABINET WAA, W2AA " " W3AA, W3AA /" " W2AA, WAA, WAA, W72AA /" " Refer to the Installation Manual for more detailed information. Dimensions of W-72A Basic Unit for Architectural & Installation Requirements (Nominal) MODEL WAA W2AA W3AA W3AA W2AA WAA WAA W72AA WIDTH (W) DEPTH (D) HEIGHT (H) UPPLY RETURN A B C B E F G I J K L M N O P Q R T 33.3 7.2 7.3 7...... 2. 2. 3. 32. 33.2 3. 2.3 3.3 2... 2.. 3.2 7.2 7.3 7. 27. 3. 27... 2. 7.3 3. 32. 33.2 3. 2. 3.3 2... 2.. 2. 22.32.. 2.. 2. 3. 3. 3. 3. 32. 2. 3. 32.3 3.37 3. 23..... 2. 22.32 3.. 2.. 2. 3. 3. 37. 3... 2.. 3.37 3. 3..... W Built In Rain Hood Pitch Heater Access Panel Electric Heat C. Breaker/ Disconnect Access Panel (Lockable) Hood for CRV and ECON models only D.2 2.3 A I ide Wall Mounting Brackets (Built In) Top Rain Flashing hipping Location E O upply Air Opening B. R. F G Filter Access Panel Ventilation Air Condenser Air Outlet tandard flush vent door for non- ERV/CRV Econ. models 3" 7. Low Voltage Electrical Entrance High Voltage Electrical Entrance Cond. Air Inlet J C K H Optional Electrical Entrances L M P Return Air Opening T Front View ide View Drain N Q Back View Bottom Installation Bracket MI-37 Not used when WECO Economizers installed. Filter access is through the WECO hood. Form No. 2-2 upersedes 2- Page 2 of
Clearances Required for ervice Access and Adequate Condenser Inlet Airflow MODEL LEFT IDE RIGHT IDE WLA, W2LA, W3LA, W3LA " 2" W2LA, WLA, WLA, W72LA 2" 2" NOTE: For side-by-side installation of two (2) WL models, there must be 2" between units. This can be reduced to " by using a WL model (left side compressor and controls) for the left unit and WA (right side compressor and controls) for right unit. Minimum Clearances Required to Combustible Materials MODEL UPPLY AIR DUCT FIRT THREE FEET CABINET WLA, W2LA " " W3LA, W3LA /" " W2LA, WLA, WLA, W72LA /" " Refer to the Installation Manual for more detailed information. Dimensions of W-72L Basic Unit for Architectural & Installation Requirements (Nominal) MODEL WLA W2LA W3LA W3LA W2LA WLA WLA W72LA WIDTH (W) DEPTH (D) HEIGHT (H) UPPLY RETURN A B C B E F G I J K L M N O P Q R T 33.3 7.2 7.3 7...... 2. 2. 3. 32. 33.2 3. 2.3 3.3 2... 2.. 3.2 7.2 7.3 7. 27. 3. 27... 2. 7.3 3. 32. 33.2 3. 2. 3.3 2... 2.. 2. 22.32.. 2.. 2. 3. 3. 3. 3. 32. 2. 3. 32.3 3.37 3. 23..... 2. 22.32 3.. 2.. 2. 3. 3. 37. 3... 2.. 3.37 3. 3..... R E Heater O Pitch Access. Panel D W upply Air Opening B ide Wall Mounting Brackets (Built In) Top Rain Flashing hipping Location Built In Rain Hood 2.3 A I.2 Electric Heat C. Breaker/ Disconnect Access Panel (Lockable) tandard flush vent door for non-erv/crv Econ. models Hood for CRV and ECON models only Return Air Opening Optional Electrical Entrances C 3" Filter Access Panel Ventilation Air. F T Drain Bottom Installation Bracket Back View Q P M N L H K J Cond. Air Inlet ide View 7. Low Voltage Electrical Entrance High Voltage Electrical Entrance Condenser Air Outlet Front View G MI-3737 Not used when WECO Economizers installed. Filter access is through the WECO hood. Form No. 2-2 upersedes 2- Page 3 of
Cooling Application Data - Outdoor Temperature Model W W2 W3 W3 W2 W W W72 Return Air (DB/WB) /2 /7 /72 /2 /7 /72 /2 /7 /72 /2 /7 /72 /2 /7 /72 /2 /7 /72 /2 /7 /72 /2 /7 /72 Cooling Capacity F F F F F F F F F 2 F 2 F 7 3 3 22 3 2 22 3 2 2 32 2 37 237 23 2 2 22 2 2 3 3 33 33 37 3 3 2 3 33 3 73 7 3 3 7 37 2 3 23 3 2 2 23 22 33 2 3 23 3 23 32 2 373 2 2 27 332 3 32 3 33 2 37 2 37 37 2 7 72 7 7 7 77 2 37 2 3 7 3 2 2 27 2 37 3 2 22 323 22 37 227 2 272 3 2 27 37 322 3 7 32 3 7 37 3 7 7 2 3 2 3 3 33 22 23 2 3 27 22 32 22 3 22 3 23 37 23 27 2 3 3 2 3 32 3 7 3 22 3 72 732 2 7 32 7 33 3 2 7 2 77 27 7 2 2 3 2 33 22 3 2 3 2 23 32 3 3 33 33 37 3 3 7 7 Below F (.3C), unit requires a factory or field installed low ambient control. Return air temperature. 3 3 32 2 2 23 72 22 7 2 2 2 22 37 2 3 2 2 37 2 3 2 2 3 2 3 32 3 337 2 32 22 2 7 3 2 2 2 23 2 7 33 3 2 2 2 2 73 7 37 2 2 2 7 73 2 22 2 2 2 22 7 7 7 23 22 2 22 2 7 3 237 22 2 2 2 2 27 2 2 2 23 2 2 23 2 3 2 27 2 2 2 7 2 7 2 27 2 2 22 2 23 23 232 22 33 333 323 37 2 27 2 23 2 37 3 32 3 23 232 22 22 23 32 33 2 23 2 22 2 27 273 27 3 373 33 327 2 2 2 2 2 37 37 7 337 2 277 27 2 2 3 3 3 327 3 33 32 37 3 3 3 3 37 32 33 33 32 37 3 2 3 32 3 23 2 3 37 3 3 33 3 3 2 7 3 2 3 373 7 2 77 2 3 37 3 33 32 7 32 2 2 7 77 7 2 2 2 7 7 3 2 2 2 3 Capacity Multiplier Factors % of Rated Airflow - Rated + Total BTUH...2 ensible BTUH... Form No. 2-2 upersedes 2- Page of
Air Conditioning Wall-Mount Model Nomenclature W 3 A A A X X X X X X ERIE NOMINAL CAPACITY - ½ Ton 2-2 Ton 3-2½ Ton 3-3 Ton 2-3½ Ton - Ton - Ton 72 - Ton A = Compressor & Controls - Right ide L = Compressor & Controls - Left ide D = DEHUMIDIFICATION OPTION Models W3A, W3A, W2A, WA & WA only. Insert D in place of dash (-). REVIION VOLT & PHAE A - 23/2// B - 23/2//3 C - //3 KW VENTILATION OPTION (ee Table Below) FILTER OPTION X - -inch Throwaway (tandard) W - -inch Washable P - 2-inch Pleated (MERV ) COLOR OPTION X - Beige (tandard) - White - Buckeye Gray - Desert Brown - Dark Bronze A - Aluminum - tainless teel CONTROL MODULE (ee Chart Below) COIL OPTION X - tandard - Phenolic Coated Evaporator 2 - Phenolic Coated Condenser 3 - Phenolic Coated Evaporator and Condenser UPPLY AIR OUTLET X - Front (tandard) For KW and circuit breakers (23/2 Volt) or toggle disconnects ( Volt) applications, insert Z in the KW field of the model number. ee Pages & for available Factory Installed KW options and Page for Field Installed Heater Packages. Ventilation Options Models Description Factory Installed Code No. WAA, W2AA WLA, W2LA Field Installed Part No. Factory Installed Code No. W3AA, W3AA W3LA, W3LA Field Installed Part No. W2AA, WAA, WAA, W72AA W2LA, WLA, WLA, W72LA Factory Installed Field Installed Code No. Part No. Barometric Fresh Air Damper - tandard X WBFAD-2 X WBFAD-3 X WBFAD- Blank-Off Plate B WBOP-2 B WBOP-3 B WBOP- Motorized Fresh Air Damper w/plug M WMFADP2 M WMFADP3 M WMFADP Commercial Ventilator - pring Return w/plug & Exhaust l V WCRVP2-* k V WCRVP3-* k V WCRVP-* k Economizer w/plug, Temp Only l Y WECOPT2-* k Y WECOPT3-* k Y WECOPT-* k Economizer w/plug, Enthalpy l Z WECOPE2-* k Z WECOPE3-* k Z WECOPE-* k Energy Recover Ventilator w/plug, 23 Volt R WERVPA2-* j R WERVPA3-* j R m WERVPA-* j Energy Recover Ventilator w/plug, Volt R WERVPC2-* j R WERVPC3-* j R m WERVPC-* j Intake and exhaust can be independently adjusted. Insert color to match unit ("X" = Beige; "" = Buckeye Gray; etc.) All Economizer & CRV versions have 7" deep intake hood. m Energy Recovery Ventilator must be field-installed on W**L models. Air Conditioning Control Modules All Models Except As Noted HPC LPC CCM LAC ALR K K ODT DDC Factory Installed Code Field Installed Part TD TD TD X TD TD TD E CMA-2 TD TD TD J Factory Only TD TD TD K CMC- and CMA-2 TD TD TD M Factory Only TD TD TD N TD TD TD Field Installed Only CMC- TD TD TD Field Installed Only CMA- TD TD TD V Factory Only TD TD TD CMA-3 for W-3 Field Installed Only CMA-3 for W2-72 K Except W & 72 TD TD TD Field Installed Only K2 W72 Only K22 W Only TD = tandard equipment for these specified models. HPC. High pressure control is auto reset. Always used with compressor control module (CCM) which is included. ee note. LPC. Low pressure control is auto reset. Always used with compressor control module (CCM) which is included. ee note. CCM. Compressor control module has adjustable 3-second to -minute delay-on-break timer. On initial power-up, or any time the power is interrupted, the delay-on-make will be 2-minutes plus % of the delay-on-break setting. There is no delay-on-make during routine operation of the unit. The module also provides the lockout feature (with retry) for high and/or low pressure controls, and a 2-minute timed bypass for low-pressure control. LAC. Low ambient control permits cooling operation down to F. LAC is fan-cycling control for outdoor fan motor on all models except W/W2 Dehum. units, which have modulating control. ALR. The alarm relay has a set of normally open and normally closed dry contacts to provide the ability to signal a condition of shutdown on either high or low pressure controls. K. PTCR start kit can be used with all -A single phase models. Increases starting torque 2-3x. Not used for -B or -C three phase models. Do not use if K or K2 is used. K. tart capacitor & potential relay start kit can be used with all -A single phase models. Increases starting torque x. Not used for -B or -C three phase models. Do not use if CMC- is used. ODT. Outdoor thermostat is adjustable from to F. It is suitable for use as a compressor cut-off thermostat. DDC. Incorporates additional sensors: discharge air temperature, indoor blower airflow, compressor current, and dirty filter. These sensing devices function to input analog data such as temperature, as well as digital data such as airflow, compressor status or filter status. pecial economizer required; consult factory. V control module should be ordered in conjunction with direct digital controller (DDC) model TC2. Refer to DDC specification sheet 32 for more information. Form No. 2-2 upersedes 2- Page of
NOTE Form No. 2-2 upersedes 2- Page of Bard Manufacturing Company, Inc. Bryan, Ohio www.bardhvac.com Due to our continuous product improvement policy, all specifications subject to change without notice. Before purchasing this appliance, read important energy cost and efficiency information available from your retailer. Form No. 2 December, 2 upersedes 2-