HYDRAULIC CRIMPING TOOL HT 51 50 380 130 2,7 End sleeves Connectors 185 70 50 70 VAL P1* 445x290xh95 1,2 * Suitable for storage of the tool and 20 sets of dies. also the HT 51-KV version, for power supply companies New design two speed hydraulic tool, lightweight and compact, this tool is ideal for working in confined spaces. Having the benefit of spring loaded handles, the dies can be advanced using only one hand; therefore leaving the other hand free to position the connector. For ease of operation and comfort of the operator, the tool head can be fully rotated through 180 degrees. The built-in safety valve will by-pass the oil supply when the maximum is reached, and a release system can easily be operated at any stage of the compression. HYDRAULIC PRESSHEAD RH 50 50 700 196 75 1,6 End sleeves Connectors 185 70 50 70 VAL P1* 445x290xh95 1,2 Canvas bag 007 350x105 0,13 * Suitable for storage of the tool and 20 sets of dies. Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 72) RH 50 is suitable for installing the same range of as HT 51. For die selection, please refer to chart on pages 76 80 57
HT 81-U HYDRAULIC CRIMPING TOOL Kg 80 485 141 3,4 This new model, lightweight and self contained, features a patented closure and release mechanism for the die locking pin. A wide range of can be crimped with a small number of die sets due to their unique, double groove styling. Dies for cutting copper, aluminium, aldrey and aluminium-steel, are also available (see table below). The tool features a double speed action: a fast advancing speed for rapid approach of the dies to the connector and a slower more powerful speed for crimping. For ease of operation and comfort of the operator the tool head can be fully rotated through 180 degrees. The built-in safety valve will bypass the oil supply when the maximum is reached, and a releasing system can easily be operated at any stage of the compression. 240 100 200 VAL P3* 620x380xh135 2,5 VAL 75** 270x80xh30 0,15 * Suitable for storage of the tool and three VAL 75. **Suitable for storing five sets of dies. RHU 81 HYDRAULIC PRESSHEAD 80 700 235 91 1,9 240 100 200 Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 72). This new model, lightweight and self contained, features a patented closure and release mechanism for the die locking pin. The head is easy to use and is ideally suited for crimping in confined spaces. RHU81 is suitable for installing the same range of as HT 81-U. Canvas bag 007 350x105 0,13 HT 81-U and RHU 81 ACCESSORIES FOR CUTTING CONDUCTORS Die Cutting Capacity Conductor MB2-80U MB3-80U Ø 16 mm Cu, Alu, Aldrey and Alu-Steel This die is suitable to cut steel conductors (R 160 dan/mm 2 ) having the most common strandings, i.e.: 19 x 1,2 = Ø est. 6,0 mm 7 x 3,0 = Ø est. 9,0 mm 19 x 2,1 = Ø est. 10,5 mm 19 x 2,3 = Ø est. 11,5 mm Suitable to cut aluminium strands of 150 mm 2 aluminium-steel conductors, wihtout damage to the steel core 58 For die selection, please refer to chart on pages 76 80
HT 131-C HYDRAULIC CRIMPING TOOL 130 473 144 5,2 This new model, self contained, robust and sturdy, will accept all semi-circular slotted dies, common to most 130 tools. The tool features a double speed action: a fast advancing speed for rapid approach of the dies to the connector and a slower more powerful speed for crimping. For ease of operation and comfort of the operator the tool head can be fully rotated through 180 degrees. RHC 131 The built-in safety valve will by-pass the oil supply when the maximum is reached, and a release system can easily be operated at any stage of the compression. 400 240 185 400 HYDRAULIC PRESSHEADS VAL P3* 620x380xh135 2,5 *Suitable for storage of the tool and 15 sets of dies 130 700 232 124 3,9 Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 72) This new design with improved mechanical features, is suitable for installing the same range of as HT 131-C. 400 240 185 400 VAL P8* 445x290xh115 1,2 *Suitable for storage of the head and 14 sets of dies RHM 132 130 700 216 80 3,1 Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 72). Particularly suitable for high volume bench crimping. 400 240 400 VAL P8* 445x290xh115 1,2 *Suitable for storage of the head and 14 sets of dies 60 For die selection, please refer to chart on pages 76 80
HYDRAULIC CRIMPING TOOL HT 131-UC 130 488 149 4,8 Alu lugs and splices 400 240 185 400 300 VAL P3* 620x380xh135 2,5 VAL 130** 360x280xh48 3,0 * Suitable for storage of the tool and 15 sets of semi-circular slotted dies. **Suitable for the storage of accessories for crimping aluminium. This robust and self contained tool will accept the accessories for performing the Deep Stepped Indent system of crimping on aluminium cables. This tool will also accept the semicircular slotted dies, common to most 130 tools. HT 131-UC performance features are the same as those of HT 131-C. HYDRAULIC PRESSHEAD RHU 131-C 130 700 245 89 3,7 Capicorda e Giunti Al 400 240 185 400 300 VAL P8* 445x290xh115 1,2 VAL 130** 360x280xh48 3,0 VAL 130-U*** 450x305xh80 5,0 * Suitable for storage of the head and 14 sets of dies ** Suitable for the storage of accessories for crimping aluminium. *** Suitable for storage of the head, semi-circular slotted dies and dies for crimping aluminium. Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 72). RHU 131-C is suitable for installing the same range of as HT 131-UC. VAL 130 VAL 130-U VAL P8 For die selection, please refer to chart on pages 76 80 61
ECW-H3D HYDRAULIC PRESSHEAD 230 700 315 120 5,2 VAL ECW-H3D* 345x305xh90 4,2 * Suitable for storage of the head and 10 sets of dies. Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 80) Adaptor type AU230-130D is available as an optional extra enabling the head to utilise the semi-circular slotted dies which are common RHU 231 MAIN APPLICATION - max section mm 2 630 300 240 630 to most 130 tools. Also available is a series of dies for the compression of DIN electrical, and a die for cutting copper, aluminium, aldrey, aluminium-steel and steel conductors. 230 700 320 110 6,4 MAIN APPLICATION - max section mm 2 ECW-H3D ACCESSORIES FOR CUTTING CONDUCTORS Die Cutting Capacity Conductor WT2-3D Ø 20 mm Cu, Alu, Aldrey and Alu-Steel Ø 20 mm Extra flexible steel with 200 strands This die is suitable to cut steel conductors (R 160 dan/mm2) having the most common strandings, i.e.: 19 x 1,2 = Ø est. 6,0 mm 7 x 3,0 = Ø est. 9,0 mm 19 x 2,1 = Ø est. 10,5 mm 19 x 2,3 = Ø est. 11,5 mm VAL 231* 470x273xh96 7,2 * Suitable for storage of the head and dies for aluminium compression Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working RHU 230-630 Alu lugs Cu lugs 500 630 of 700 max, (see page 80). It allows crimping up to 500 sqmm aluminium. Dies are available also for the crimping of copper. VAL 231 Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 80). RHU 520 230 700 365 193 9,0 MAIN APPLICATION - max section mm 2 Cu lugs Alu lugs 400 630 185 400 It allows for crimping up to 630 sqmm aluminium (according to HN 68 S90). Adapter AU 230-130 C, is available as an optional extra enabling the head to utilise the semicircular slotted which are common to most 130 tools. VAL 230-630* 405x230xh145 4,4 VAL MAT 230-630* 290x260xh70 3,1 * Suitable for storage of the head ** Suitable for storage the accessories VAL 230-630 VAL MAT 230-630 520 700 306 200 18,0 MAIN APPLICATION - max section mm 2 Lugs H.V. overhead lines 1200 630 VAL 520* 405x230xh145 4,4 VAL MAT 520** 500x310xh68 5,6 * Suitable for storage of the head ** Suitable for storage of 10 sets of dies. 62 Hydraulic presshead complete with quick automatic coupler for connection to a hydraulic pump with a working of 700 max, (see page 80). Adaptor type AU520-130C is available as an optional extra enabling the head to utilise the semi-circular slotted dies which are common to most 130 tools. For die selection, please refer to chart on pages 84 88 VAL MAT 520 VAL 520
B 131-C 14.4 V CORDLESS HYDRAULIC CRIMPING TOOL height Battery Kg (with battery) 130 420 250 100 14,4 V 2.0 Ah 7 End sleeves Connectors 400 240 185 400 14.4 V cordless hydraulic crimping tool, lightweight and balanced for single hand operation. This tool will accept all semi-circular slotted dies, common to most 130 tools. The tool features a double speed action: a fast advancing speed for rapid approach of the dies to the connector and a slower more powerful speed for crimping. For ease of operation and comfort of the operator the tool head can be fully rotated through 180 degrees. The tool is powered by 14.4 V d.c. NiCd battery. A balanced tool for optimum control. Quiet in operation with very little vibration. Lightweight construction enables the operator to hold the tool in one hand and to position the connector with the other hand. The operating buttons, crimp/release, are mechanically interlocked, to prevent accidental operation of the tool. A microprocessor controls the tool operation and automatically cuts out the motor, on completion of the crimping operation, saving energy and extending battery life. The residual battery capacity is automatically displayed after every cycle. Fitted with an integral socket, for connection to a 12 V dc external power supply/vehicle battery. The tool is provided with a maximum valve. VAL B 131* 528x404xh130 6,4 *Suitable for storing: - Basic tool complete with battery and shoulder strap - Spare battery - Battery charger - Suitable for storing 12 sets of semi-circular slotted dies Lightweight and ergonomically shaped Head rotates through 180 Battery condition display Easy to operate with only one hand Die release system, protected from accidental operation For die selection, please refer to chart on pages 84 88. 76
14.4 V CORDLESS HYDRAULIC CRIMPING TOOL B 131-UC height Battery Kg (with battery) 130 435 250 100 14,4 V 2.0 Ah 7,3 Connectors All lugs 400 240 185 400 300 VAL B 131* 528x404xh130 6,4 *Suitable for storing: - Basic tool complete with battery and shoulder strap - Spare battery - Battery charger - Suitable for storing 12 sets of semi-circular slotted dies 14.4 V cordless hydraulic crimping tool, lightweight and balanced for single hand operation. This tool will accept the accessories for performing the Deep Stepped Indent system of crimping on aluminium cables. This tool will also accept the semicircular slotted dies, common to most 130 tools. The tool features a double speed action: a fast advancing speed for rapid approach of the dies to the connector and a slower more powerful speed for crimping. For ease of operation and comfort of the operator the tool head can be fully rotated through 180 degrees. The tool is powered by 14.4 V d.c. NiCd battery. A balanced tool for optimum control. Quiet in operation with very little vibration. Lightweight construction enables the operator to hold the tool in one hand and to position the connector with the other hand. The operating buttons, crimp/release, are mechanically inter- locked, to prevent accidental operation of the tool. A microprocessor controls the tool operation and automatically cuts out the motor, on completion of the crimping operation, saving energy and extending battery life. The residual battery capacity is automatically displayed after every cycle. Fitted with an integral socket, for connection to a 12 V dc external power supply/vehicle battery. The tool is provided with a maximum valve. High power battery Motor ventilation. Operating and release buttons mechanically interlocked. Socket for 12 14.4 V dc external power supply. For die selection, please refer to chart on pages 84 88. 77