PRT 1 -GENERL 1.01 RELTED DOCUMENTS SECTION 10 1425 IDENTIFYING DEVICES. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. 1.02 SECTION INCLUDES. Exterior Letters and numbers-building ddress Signage. B. Interior Room Signs (Outside of Public Toilet Rooms Only). 1.03 SUBMITTLS. See Section 01 3000- Submittals, for submittal procedures. B. Product Data:. Submit manufacturer's specifications, installation instructions, and general recommendations for each major product required. Include data substantiating that products to be furnished comply with requirements of the Contract Documents. C. Selection Samples: For initial selection of colors and textures, submit manufacturer's color charts consisting of actual product pieces, showing full range of colors and textures available. PRT 2- PRODUCTS 2.01 EXTERIOR SIGNGE. Manufacturer/Product: Gemini Incorporated; www.signletters.com 1. Sizes: a. Letters: 16 gauge Flat Cut Metal letters. b. Colors/patterns: 1) Letter/number style: 8" Helvetica. Provide for up to 4 number characters to be determined by address. 2) Color as selected by rchitect. c. Mounting: Stud, separated from surface by 1/2 inch. 2. Substitutions: See Section 00650 Substitution Request. 2.02 INTERIOR ROOM SIGNS (OUTSIDE OF TOILET ROOMS 129 ND 140 ONLY). Graphic Braille Signs, multi layered acrylic with raised copy and braille. 1. Sign size: 8 by 8 inches. 2. Graphics: International symbols for unisex use. 3. Lettering: 5/8 inch high, raised 1/32 inch, with Number 2 Braille coding. 4. Color: Selected by rchitect. PRT 3- EXECUTION 3.01 EXMINTION. Verify that surfaces to receive letters and signs have been finished, and that finishes are dry. 3.02 INSTLLTION. Install letters and door signs in accordance with manufacturers printed installation instructions. B. Locate exterior signs as required by the City of Columbia for addresses. C. Locate interior signs in accordance with DG requirements. END OF SECTION PW 201430 10 1425/1 IDENTIFYING DEVICES
THIS PGE INTENTIONLLY LEFT BLNK
PRT1 GENERL 1.01 SECTION INCLUDES SECTION 10 2800 TOILET, BTH, ND LUNDRY CCESSORIES ccessories for toilet rooms, showers, residential bathrooms, and utility rooms. B. Grab bars. PRT 2 PRODUCTS 2.01 MNUFCTURERS 2.02 MTERILS ll toilet accessories except grab bars are to be provided by the Owner and installed by Contractor. ccessories - General: The following accessories are to be provided by Owner and installed by Contractor. 1. Toilet paper Dispenser 2. Towel Bars and/or hooks 3. Medicine cabinets 4. Mirrors B. Stainless Steel Tubing: STM 269, Type 304 or 316. C. Fasteners, Screws, and Bolts: Hot dip galvanized, tamper-proof, security type. 2.03 FINISHES Stainless Steel: No. 4 satin brushed finish, unless otherwise noted. B. Baked Enamel: Pretreat to clean condition, apply one coat primer and minimum two coats epoxy baked enamel. 2.04 TOILET ROOM CCESSORIES Grab Bars: Stainless steel, nonslip grasping surface finish. 1. Standard Duty Grab Bars: a. Push/Pull Point Load: 250 pound-force, minimum. b. Dimensions: 1-1/4 inch outside diameter, minimum 0.05 inch wall. thickness, exposed flange mounting, 1-1/2 inch clearance between wall and inside of grab bar. c. Length and Configuration: s indicated on drawings. d. Products: 1) B-5806 series. PRT 3 EXECUTION 3.01 EXMINTION Verify existing conditions before starting work. B. Verify exact location of accessories for installation. C. Provide blocking, reinforcing plates, and concealed anchors in walls and ceilings where required for mounting. 3.02 PREPRTION Deliver inserts and rough-in frames to site for timely installation. B. Provide templates and rough-in measurements as required. 3.03 INSTLLTION Install accessories in accordance with manufacturers' instructions in locations indicated on the drawings. B. Install plumb and level, securely and rigidly anchored to substrate. CCESSORIES PW 201430 10 2800/1 TOILET, BTH, ND LUNDRY
C. Mounting Heights: s required by accessibility regulations, unless otherwise indicated. 1. Grab Bars: s indicated on the drawings. 2. Mirrors: 40 inch, measured to bottom of mirrored surface. END OF SECTION PW 201430 10 2800/2 TOILET, BTH, ND LUNDRY CCESSORIES
PRT1 GENERL 1.01 SECTION INCLUDES. Fire extinguishers. B. Fire extinguisher cabinets. 1.02 SUBMITTLS SECTION 10 4400 FIRE PROTECTION SPECIL TIES. See Section 01 3000 - dministrative Requirements, for submittal procedures. B. Product Data: Provide extinguisher operational features, color and finish, and anchorage details. C. Manufacturer's Installation Instructions: Indicate special criteria and wall opening coordination requirements. 1.03 FIELD CONDITIONS. Do not install extinguishers when ambient temperature may cause freezing of extinguisher ingredients. PRT 2 PRODUCTS 2~1 MNUFCTURERS. Fire Extinguishers: 1. Larsen ; Product MP-5: www.larsenmfg.com 2. Provided by Owner. B. Fire Extinguisher Cabinets and ccessories: 1. Larsen's Manufacturing Co; Product FS-2409-6R with Vertical Duo Door with tempered glass: www.larsensmfg.com. Use fire rated cabinet where located in fire rated assemblies. 2. Substitutions: See Section 01 6000- Product Requirements. PRT 3 EXECUTION 3.01 EXMINTION. Verify existing conditions before starting work. B. Verify rough openings for cabinet are correctly sized and located. 3.02 INSTLLTION. Install in accordance with manufacturer's instructions. B. Secure rigidly in place. C. Place extinguishers in cabinets. END OF SECTION PW 201430 10 4400/1 FIRE PROTECTION SPECILTIES
THIS PGE INTENTIONLLY LEFT BLNK