heat model Heater Quiet fan heater for connection to water in small buildings Application is a compact fan heater with very low sound level designed for water connection. It is ideal for use where fan heaters are traditionally used such as in industrial buildings and warehouses, but also in environments with high demands on low sound levels, for example, stores and assembly halls. Comfort Frico's fan heaters are extremely quiet and quickly provide comfortable heating. The heater fan is equipped with an air director, which has individually adjustable louvres and directs the air as required. Operation and economy Frico's air fan heaters have a long life, providing fast and effective heating at a low cost. The air for can be controlled in three steps, which gives energy efficient put. Product specifications Very low sound level. Mounted using the enclosed bracket on the wall or ceiling. Intended to pump hot water up to +0 C in the standard design, but available for water temperatures up to +30 C in special designs. Supplied with air director with individually adjustable louvres that direct the air on one plane. Three fan speeds. Corrosion proof housing made of hot zincplate and powder enameled steel panels. Colour: RAL 906, NCS 0500 (white). Aluminium louvres. Design The fan heater has a classic clean design in white enamelled sheet steel.
Technical specifications heater Heat put* * Sound level* 3 Voltage Amperage Weight [W] [m 3 /h] [db(a)] [V] [A] [kg] 8-0 0,0/0,3 34-45 30V~ 0,3 5 * ) Applicable at water temperature 80/60 C, surrounding temperature +5 C, fan min-max. * ) Applicable at fan min-max * 3 ) Applicable at fan min-max. Conditions: Distance to fan 5 m. Direction factor:. Equivalent absorption area: 00 m. Protection class: IP44. CE compliant. Dimensions 88 Outlet 370 50 8 Inlet 75 66 37 50 450 46 00 7 90 4 6.5 Mounting and connection Mounting The fan heater can be mounted on the wall for horizontal air in or on the ceiling for vertical air in. Installation of the heating coil Pipe connections can be made on either side of the fan heater. The heating coil has copper pipes with plain pipe connections, for solder or compression couplings. The bleed valve must be connected on the high point side of the unit. Bleed and drain valve not included with the unit. For correct inlet and let connection of the heating coil, see the dimension diagrams. Electrical installation The fan heater is intended for permanent installation. Design and specifications are subject to change with notice.
charts water Incoming / going water temperature 30/65 C Max 0,3 6,8 47 0,06 4, 5 0,05,9 54 0,05 Med 0,7 5, 49 0,06,6 54 0,05,8 56 0,04 Min 0,0,6 54 0,05 0,6 58 0,04 9,6 60 0,04 Incoming / going water temperature 90/70 C Max 0,3 5,7 44 0,9 3, 49 0,6,9 5 0,5 Med 0,7 4,3 46 0,8,0 5 0,5 0,9 53 0,3 Min 0,0,7 5 0,4 9,8 55 0, 8,9 57 0, Incoming / going water temperature 80/60 C Max 0,3 3,3 39 0,6 0,8 43 0,3 9,6 46 0, Med 0,7, 40 0,5 9,9 45 0, 8,8 47 0, Min 0,0 9,9 44 0, 8, 48 0,0 7, 49 0,09 Incoming / going water temperature 70/40 C Max 0,3 8,8 7 0,07 6,3 3 0,05 5,0 33 0,04 Med 0,7 8,0 8 0,06 5,8 3 0,05 4,6 34 0,04 Min 0,0 6,6 3 0,05 4,6 34 0,04 3,6 35 0,03 Incoming / going water temperature 60/40 C Max 0,3 8,5 6 0,0 6, 3 0,07 4,9 33 0,06 Med 0,7 7,7 7 0,09 5,5 3 0,07 4,4 34 0,05 Min 0,0 6,3 30 0,08 4,5 33 0,05 3,6 35 0,04 Incoming / going water temperature 60/30 C Max 0,3 6, 0 0,05 3,0 3 0,0,3 6 0,0 Med 0,7 5,5 0,04,9 4 0,0, 7 0,0 Min 0,0 4,4 0,04,5 5 0,0,9 8 0,0 Incoming / going water temperature 55/35 C Max 0,3 7, 3 0,09 4,8 8 0,06 3,5 9 0,04 Med 0,7 6,6 4 0,08 4,4 8 0,05 3, 30 0,04 Min 0,0 5,4 6 0,06 3,5 9 0,04,4 30 0,03
Pressure drop water pressure drop over water coil [m³/h] Pressure drop [kpa] 70 0,,0 0 0,7 Pressure drop [bar] 0 0, 0,0 0,,0 0,0 presssure drop over controls and valves [m³/h] Pressure drop [kpa] 70 0,,0 0 0,7 Pressure drop [bar] 0 0, 0,0 0,,0 The pressure drop is calculated for an average temperature of 70 C (PVV 80/60). For other water temperatures, the pressure drop is multiplied by the factor K. 0,0 Average temp. water C 40 50 60 70 80 90 K.0.06.03.00 0.97 0.93
5 0 30 5 0 5 Heater Control options 3-step control of air only The air is manually controlled in three, fixed steps. No heat control, full water through the heating coil. Complete control equipment: CB30N, control panel Thermostat and 3-step control The thermostat starts/stops the fan and controls heating on/off. The air is manually controlled in 3 fixed steps. Complete control equipment: CB30N, control panel KRT900 or T0/TK0, room thermostat SWR0/5, valve set, or TVV0/5, valve + SD0, actuator Thermostat and 3-step control with save-reduction The thermostat starts/stops the fan and controls heating on/off. The air is manually controlled in 3 fixed steps. Save-reduction saves energy through lower temperatures, for example, at night and weekends. Complete control equipment: CB30N, control panel RTI, -step thermostat SWR0/5, valve set, or TVV0/5, valve + SD0, actuator KUR, time switch Controls and accessories CB30 T0 TK0 KRT900 RTI KUR T0/TK0, thermostats Processor controlled thermostats with concealed and visible dials. Setting range +5 +30 C. Connection voltage: 30 V. Max. breaking current: 0 A. IP30. KRT900, capillary tube thermostat Capillary tube thermostat with concealed dial. Setting range 0 +40 C. Max. breaking current: 6/0 A (30/400 V). IP55. RTI, electronic -step thermostat Processor controlled -step thermostat with concealed dial. Setting range +5 +35 C. Connection voltage 30 V (two potential free contacts). Max. breaking current: 6/0 A (30/400 V). IP44. CB30N, control panel Regulates the air in 3 steps. Supplied enclosed for wall mounting. Can regulate several units. Max. rated current: 0A. IP44. KUR, digital time switch Digital weekly timer with 8 different program steps (36 memory places) equipped with a changeover contact. Max. breaking current: 0 A. IP44. SWFT0, wire mesh filter can be fitted with a wire mesh filter. The filter is fitted in front of the heating coil (slid into the provided slots) and is accessible both from above and below the heater. Description HxBxD [mm] T0 Electronic thermostat 80x80x3 TK0 Electronic thermostat visible knob 80x80x3 KRT900 Room thermostat 65x57x60 RTI -step room thermostat 55x87x43 CB30N Control box for 55x87x43 KUR Digital time switch 75x85x05 SWFT0 Basic filter
regulation AV0/5 JVF0/5 TVV0/5 SD0 SWR0/5, valve set This valve set is suitable when there is need for adjusting the water and shutting it off (for the purpose of maintenance). The supply of heat is controlled by a thermostat. Pipe dimension for SWR0 is DN 0 (¾ ) and for SWR 5, DN 5 ( ). Add a suitable thermostat for controlling SWR0/5, like KRT900 or T(K)0. SWR0/5 consists of the following: AV0/5, stop valve Stops the water supply to SW. Consists of a ball valve which is either open or closed. JVF0/5, adjustment valve To adjust the water to desired. (kv value for JVF0 is 3,5 and kv value for JVF5 7,0). TVV0/5, -way regulation valve Pressure class PN6. Maximum pressure MPa (0Bar). Maximum pressure fall TVV0, 00kPa (Bar). Maximum pressure fall TVV5, 6kPa (0,6Bar). The kv value is adjustable in 3 stages: TVV0: kv,6, kv,5 and kv 3,5 TVV5: kv,5, kv 4,0 and kv 5,5 TVV0/5, valve+ SD0, actuator regulation with heat supply controlled by thermostat, but with the option of adjusting or stopping the water. Pipe dimension for TVV0 DN 0 (¾ ) and for TVV5, DN 5 ( ). Add a suitable thermostat for controlling TVV0/5 + SD0, like KRT900 or T0/TK0. For this type of water regulation the following components are required: TVV0/5, -way regulation valve Pressure class PN6. Maximum pressure MPa (0Bar). Maximum pressure fall TVV0, 00kPa (Bar). Maximum pressure fall TVV5, 6kPa (0,6Bar). The kv value is adjustable in 3 stages: TVV0: kv,6, kv,5 and kv 3,5 TVV5: kv,5, kv 4,0 and kv 5,5 SD0, actuator on/off 30V~ A thermostat controls the actuator to open and close, thereby regulating the supply of heat to SW. The closing time of the valve is 5 seconds, prevents sudden pressure changes in the pipe system. IP40. SD0, actuator on/off 30V~ A thermostat controls the actuator to open and close, thereby regulating the supply of heat to SW. The closing time of the valve is 5 seconds, prevents sudden pressure changes in the pipe system. IP40. Description SWR0 Valve set connection 0 mm (¾ ) SWR5 Valve set connection 5 mm ( ) TVV0 -way control valve 0 mm (¾ ) TVV5 -way control valve 5 mm ( ) SD0 Acutator on/off 30V~ IP40
Wiring diagrams 3-step control of air only CB30N, controlbox Blue Brown M ~ White Grey Black Yellow Yellow Yellow/Green 30V~ 3 4 5 6 CB30N Thermostat and 3-step control T0, electronic thermostat SD0 SD0, actuator TVV0/5 3 4 5 6 CB30N, controlbox >t C T0 A/B 7 6 4 4 CB30N TVV0/5 two way valve L N 30 V~
Wiring diagrams Thermostat and 3-step control SD0 TVV0/5 SD0, actuator KRT900, room thermostat 3 KRT900 3 4 5 6 CB30N TVV0/5 two way valve CB30N, controlbox L N 30 V~ Thermostat and 3-step control with save-reduction SD0 CB30N, controlbox RTI, electronic -step thermostat KUR c 5 4 3 7 6 5 4 3 L N TVV0/5 3 4 5 6 CB30N SD0, actuator TVV0/5 two way valve RTI L N 30 V~ KUR, digital time switch