DE-06 Plain Edge Protector Seal Options used with/without s Range FD60 Product Range FD60 Intumescent & Smoke seal (brush seal) DE-04 with Intumescent Seal DE-05 with Intumescent & Smoke Seal (twin fin) Intumescent & Smoke seal (elastomeric fin) DE-05 with Intumescent & Smoke Seal (brush) Intumescent seal
Latched or Unlatched Single acting single doorset ( & overpanel) Double acting single doorset (& overpanel) Latched or Unlatched Single acting double doorset (& overpanel) Double acting double doorset (& overpanel) Doorset Configurations FD60 Doorset Configuration - FD60
9003 100 26 105 101 801 136 162 112 25 879 6033 Colour Options Standard Colours Snow White Eggshell Taupe Mocha French Cream Grey Cloud Pearl Grey Charcoal Pacific Blue Storm Dusty Jade Mint Turquoise Please Read Door Edge Protection FD60 Non-Standard Colours 933 Mission White 24 Dove 14 Mimosa 16 Harvest Gold 17 Sherbet 2012 Salmon 663 Violet 520 Imperial Purple 11 Alpine Blue 12 Cobalt 10 Mint Green 129 Yale Blue 967 Hunter Green 193 Gingerspice 966 Burgundy 108 Black 845 Spectrum Red 111 Wedgewood Blue CS Acrovyn Edge Protectors have been tested and assessed to BS 476 Part 22 1987 achieving in excess of 30 minutes (DE-01, DE-02 and DE-03) and 60 minutes (DE-04, DE-05 and DE-06) fire resistance when tested as part of timber based fire door assemblies. Chiltern test reports RF11059, RF11061 and Chiltern assessments ChiltA11129, ChiltA11130 refer. Where smoke seals are incorporated into the Acrovyn Edge Protectors in order for the door assemblies to provide cold smoke control, the smoke seal elements have been independently tested to BS 476 Part 31.1 and have achieved leakage rates not exceeding 3m³/m/hr when tested at 25 Pa. CS Acrovyn Edge Protectors are not designed or intended to upgrade non fire rated door assemblies to fire resisting assemblies but are designed and tested for use with fire door assemblies of proven fire resistance to current BS and EN test methods. The buyer takes responsibility for determining suitability and compliance with relevant mandatory requirements. recommend that where any doubt exists, expert opinion is sought.
Latches and Locks Door Edge Gaps Head Seals 1 x C/S Intumescent seal and 1 x C/S Intumescent & Smoke seal must be fitted 5mm each side of the centreline within frame reveal. Fixings Door Frame Protection Door frames may have the jambs partially or fully clad with 2mm thick Acrovyn which must be bonded to the frame using 3M Scotch/grip cement 10 contact adhesive, or equivalent. Frame Seals 1 x C/S Intumescent seal and 1 x C/S Intumescent & Smoke seal must be fitted 5mm each side of the centreline within frame reveal. Door Leaf Construction Graduated density or laminated particleboard, Laminated softwood or hardwood strip core with timber based facings, Timber based stiles and rails with flaxboard or particleboard cores and timber based facings. Timber based stiles and rails with timber, flaxboard or particleboard cores, non-combustible sub-facings and timber based external facings Glazing within constructions is permitted. Hardware Protection 1mm thick intumescent paper under : - Hinge blades, - Encasing latch bodies, - Latch forends, - Latch keeps, - Flush bolts No lippings required. Hinges Door Frame Construction Optional Door Leaf Protection Door leaves with Acrovyn Protection must be bonded to the doors using 3M Scotch/grip cement 10 contact adhesive, or equivalent. Flush Bolts Flush bolts meeting the following criteria are acceptable:
FD60 Single Door Leafs FD60 Double Door Leafs Door Leaf Dimensions FD60 Door Leaf Dimesions - FD60