D0A/D/D6AW/D80A/D90 Series EN Installation Instructions / Smoke/Heat Detector Bases
EN. D0A/D/D6AW/D80A/D90 Series Installation Instructions.0 Trademarks M Weatherban is a trademark of M. All rights reserved. Notice Use these instructions when installing the D/D6AW/D80A Series / Smoke Detector Bases. These bases are compatible with the Bosch 000, 7000, 8000, and 9000 Series Fire Alarm Control Panels (FACP). Devices covered by these instructions have two components: a detector base and a detector head. All devices have an LED indicator. Install, test, and maintain the D/D6AW/D80A Series according to these instructions, NFPA 7, local codes, and the authority having jurisdiction (AHJ). Follow the procedures in these instructions to avoid personal injury or damage to the equipment. Failure to follow these instructions can result in the detector not initiating an alarm condition. Bosch Security Systems, Inc. (Bosch) is not responsible for improperly installed, tested, or maintained D/D6AW/D80A Series Smoke Detector Bases..0 Mounting Box The diameter of each D0A, D, D6AW, D80A, and D90 Smoke Detector Base is 6 in. (. cm). These bases fit on standard in. (0. cm) octagonal mounting boxes, and in. (0. cm) square mounting boxes..0 Installation Standards Seal all field wire openings with a nonflammable sealing compound such as M Weatherban Acrylic Sealant 606- NF. Mount the detectors on walls between in. and in. (0. cm and 0. cm) from the ceiling or on the ceiling at least in. (0. cm) from the wall. Ensure the installations conform to the specifications listed in Table on page 7. The D/D6AW/D80A Series determines the alarm current. Refer to Table on page 7 for more information. Wire the detectors as shown in Figure through Figure on pages through..0 Testing Instructions Test the D/D6AW/D80A Series at installation and every two years thereafter according to NFPA 7. Test using the D000 Calibrated Smoke Detector Tester or the D00 Magnetic Calibrated Test Pole..0 Smoke Detector Bases. Installing Smoke Detectors When using the smoke detectors with Bosch control panels, you can power the detectors from the control panel s auxiliary power supply. The Alarm LED, located on the D6AW / Smoke Detector Head, flashes to indicate power to the detector. This LED lights steadily to indicate an alarm condition.. Two-Wire Operation Wiring Connect the D6AW wiring as shown in Figure on page. For proper detector system supervision, do not wires around the screw terminals. Cut the wire and make individual in and out connections. Bosch Security Systems, Inc. /07 F0U06-06
. Figure : D6AW Smoke Detector Base Wiring D0A/D/D6AW/D80A/D90 Series Installation Instructions 6 6 - D6AW Smoke Detector Base - Initiating negative (-) - From the previous smoke detector base or FACP When using the DB Powered Loop Interface Module, there are a maximum number of 0 smoke detectors per. You can install up to five smoke detectors on the D000 Series Control Panel. Refer to the appropriate detector manufacturer s installation guide for EOL resistor values. The D6AW Detector Base does not have Terminals and. - Initiating positive (+) - End-of-line resistor.0 Smoke Detector Bases. Installing the Smoke Detectors The Alarm LEDs are located on the D8A, D8A, and D8A Smoke Detector Heads. These LEDs flash to indicate power to the detector and light steadily to indicate an alarm condition. Do not wires around the terminals. Cut the wire and make individual in and out connections.. Two-Wire Operation Wiring Connect the D80A wiring as shown in Figure on page. The current for the optional LED must be limited to 0 ma or the detector might be damaged or might not initiate alarms. Bosch Security Systems, Inc. /07 F0U06-06
D0A/D/D6AW/D80A/D90 Series Installation Instructions Figure : D80A Smoke Detector Base Wiring 6 6 9 6 7 6 7 6 - To control panel power supply (-) -. kω, ½ W current-limiting resistor - Optional LED - D80A Smoke Detector Base - Initiating negative (-) 8 6- From the previous smoke detector base or FACP 7 - Initiating positive (+) 8 - Current limiting resistor* 9 - EOL resistor *The current-limiting resistor is only an example. Not all of the annunciators have in-line resistance. The annunciator must be current-limited to 0 ma at maximum.. Four-Wire Operation Wiring Generally, four-wire detectors are connected to an un-powered detection. The D7 Power Supervision Relay supervises the power to the detectors. Connect the detector to an appropriate initiation when using a D9GV, D9G, D9, D7GV, D7G, D7, D7, D8, D9, or D9 FACP. Connect the D90 wiring (refer to Figure on page ). 6.0 / Heat Detector Bases Do not wires around the terminals. Cut the wire and make individual in and out connections. The D0A is a non-current limited, non-latching detector base without an LED indicator. This base is used in and modes, and in twowire applications. Connect the D90 wiring (refer to Figure on page ). The D is a, two-wire latching detector base with an LED indicator. The D and D / Fixed Temperature Heat Detector heads are compatible with the D0A and D Detector Bases. The D6A and D7 Fixed Temperature Head Detector heads are compatible with the D0A and D Detector Base. Refer to Table on page 6 for smoke detector and base listings. Bosch Security Systems, Inc. /07 F0U06-06
. D0A/D/D6AW/D80A/D90 Series Installation Instructions Figure : D90 Smoke Detector Base Wiring 6 L H07 D90 L H L H07 D90 L H 7 S S L L H S S L L H 9 8 6 0 H H N/O (YEL) COM (ORN) N/C (PUR) - Initiating positive (+) - positive (+) from UL Listed supply - negative (-) from UL Listed supply - Initiating negative (-) - EOL resistor 6 - Blue wire 7 - Yellow wire 8 - D7 EOL Relay 9 - Black wire 0 - Initiating form A contact - Auxiliary form C contact Figure : D0A Heat Detector Base and D Heat Detector Base Wiring 9 6 L L 6 L L 8 - D0A Smoke Detector Base - (+) red lead - D Heat Detector Base - heat detector circuit (red lead) - (-) heat detector circuit (black lead) 6 - To remote annunciator/led (blue lead) 7 7 - (-) black lead 8 - Latching red LED 9 - EOL resistor Bosch Security Systems, Inc. /07 F0U06-06
D0A/D/D6AW/D80A/D90 Series Installation Instructions Table : Smoke Detector and Base Listings Model Application Voltage Wiring Base Diameter Features Color D6W Base / Two-wire 6 in. (. cm) N/A White D6AW Base / Two-wire 6 in. (. cm) LED latches White D80A Base Two-wire 6 in. (. cm) N/A D90 Base Four-wire 6 in. (. cm) N/A White D0A Heat base / Two-wire 6 in. (. cm) N/A D Heat base Two-wire 6 in. (. cm) power, latches D Heat head / N/A N/A Fixed + F (+7 C) D Heat head / N/A N/A Fixed +90 F D6A Heat head N/A N/A Fixed Rate-ofrise + F (+7 C) D7A Heat head N/A N/A Fixed Rate-ofrise +90 F D6AW D8A Photoelectric smoke head Photoelectric smoke head / N/A N/A N/A N/A D8A Ionization head N/A N/A D8A D7 Photoelectric smoke head EOL power supervision module N/A N/A power, latches power, latches power, latches power, latches steady with fixed + F (+7 C) heat detector White / N/A N/A N/A N/A 6 Bosch Security Systems, Inc. /07 F0U06-06
. 7.0 Specifications D0A/D/D6AW/D80A/D90 Series Installation Instructions Table : Smoke Detector Head Specifications Detector Head D8A D8A/D8A D6AW D/D D6A/D7A Detector Type Fixed Temp/Rateof-rise Working Voltage (two-wire) Rated Voltage (four-wire) Maximum Alarm Current* Ionization.0 to.0 7.7 to 0.0 Photo (D8A)/P Photo with Heat (D8A).0 to.0 7.7 to 0.0 Photoelectric 8.0 to.0 8.7 to.0 Fixed Temp/Rateof-Rise Heat Detector D: + F (+7 C) D: +90 F The alarm current is determined by the detector base. Refer to Table for more information. Surge Current 00 μa 60 μa 00 μa 60 μa Standby Current 0 μa μa Heat Element Rating N/A + F (+7 C) for the D8A 8 μa at / μa at N/A Compatibility Identifier HD HD HD UL Calibrated Magnetic Test Yes Yes Yes Fire Alarm Control Panel D: + F (+7 C) D: +90 F D N/A N/A N/A N/A N/A D N/A N/A N/A N/A N/A D7 with DB D9, D9GV, D9G, D9, D7GV, D7G, D7 with DB Table : Detector Base Specifications Fixed Temp/Rate-of- Rise Heat Detector D6A: + F (+7 C) D7A: +90 F.0 to.0 7.7 to 0.0 0 μa D6A: + F (+7 C) D7A: +90 F Base Diameter Wiring Alarm Current Operating Voltage D0A 6 in. (. cm) Two-wire N/A 8.0 to 6. D 6 in. (. cm) Two-wire ma maximum.0 to 6. D6AW 6 in. (. cm) Two-wire N/A 8.0 to 6. D80A 6 in. (. cm) Two-wire 70 ma maximum.0 to 6. D90 6 in. (. cm) Four-wire 8 ma maximum.0 to 6. Bosch Security Systems, Inc. /07 F0U06-06 7
Bosch Security Systems, Inc. 0 Perinton Parkway Fairport, NY 0-999 USA (800) 89-0096 007 Bosch Security Systems, Inc. F0U06-06