Installation and Operation Manual

Transcription

1 Page 1 Installation and Operation Manual Microseparator System For ES4 Edgers Distributed Exclusively by: Satisloh North America N 116, W Morse Drive Germantown, WI Tel: (262) Fax: (262) Manufactured for Satisloh by: Bazell Technologies Corporation 5066 Commercial Circle Concord, CA Tel: (925) Fax (925) info@bazell.com Web: Bazell Technologies Corporation is a Satisloh Technology Partner M000021_C September 2013

2 Page 2 TABLE OF CONTENTS TABLE OF CONTENTS... 2 PRODUCT DEFINITION... 4 OPERATOR SAFETY... 4 INSTALLATION LIMITATIONS... 5 SPECIFICATIONS... 5 RECEIVING AND INSPECTION... 5 LIFTING... 5 INSTALLATION ELECTRICAL... 6 INSTALLATION PIPING... 6 INLET... 6 OUTLET... 7 WATER MAKE-UP... 7 AIR SUPPLY CHILLER SUPPLY (TEMPERATURE CONTROL OPTIONAL)... 8 START-UP... 9 FILL TANK... 9 CONTROL PANEL FUNCTIONS... 9 STARTING AND STOPPING... 9 ALARMS LOW LEVEL TANK ALARM HIGH LEVEL TANK ALARM LOW TEMPERATURE ALARM HIGH TEMPERATURE ALARM LOW AIR PRESSURE ALARM NO WORK AUTO FILL MODE LEVEL SWITCH ERROR MOTOR OVERLOAD OVERLOAD EMERGENCY STOP DAILY PRODUCT STARTUP TANK CLEANING CONTROL SUMMARY FUNCTION SETUP CALIBRATION WARNINGS, ALERTS AND FAULTS SCREEN CLEANING SYSTEM DIMENSIONS AND UTILITIES... 17

3 Page 3 DRAWING 6SBTB EDGER SYSTEM PROCESS FLOW DRAWING # 6SBTE DRAWING # 6SBTE SYSTEM PARTS LIST DRAWING # 6SBTE LIMITATIONS OF WARRANTY DOCUMENT REPRESENTATION CONTACTING BAZELL TECHNOLOGIES... 26

4 Page 4 Product Definition The Microseparator Edger water system is designed for the clarification of Water used in the edging of ophthalmic lenses. Design elements: Compact design with low water inlet height left or right side entry Automatic PC/HI chip separation Easy lens/block retrieval through operator door Automatic water makeup Refrigeration coil (chiller, thermocouple, controller, etc. optional) Simple push button control interface Designed for use with secondary filters 100 PSI minimum Operator Safety All personnel responsible for operating the Edger System should be required to read these safety and cleaning procedures prior to operation. Important safety devices are built into each system. Please carefully observe the following safety notices. Always disconnect and lock out the power source before working on or near the Edger System. Motor controls should conform to instructions given in the installation manual provided with the Edger System. Motor controllers must be securely and adequately grounded according to NEC and local codes of the specific area. The Chip Separator must be operated with the cover on. Do not place any appendage in the Chip Separator, to avoid being caught by the pneumatic arm. Practice good housekeeping and maintain a Safety Training and Safety Equipment Operation/Maintenance Program for all employees.

5 Page 5 Installation Limitations Specifications Model Name Polycarbonate Removal Maximum Flow Rate Water Tank Water Pump Cooling Coil Control Panel ES4 Edger System Self-cleaning Chip Separator 76 l/min (20 GPM) 304 SS, capacity 80 L (21 gals) Brinkmann Plastic body Copper Per the drawings attached Note: The Microseparator ES4 Edger System is designed to support the recirculating water requirements of (2) edgers only. Any attempt by the owner to utilize the equipment for other than the intended purpose is at his or her own risk. Receiving and Inspection As soon as possible upon receipt of shipment, machine should be uncrated and packing list checked. Any shortages should be reported to Bazell Technologies Corporation immediately. If damage has occurred during transit, file a claim with the carrier and notify Bazell Technologies of such action. Lifting Lift tank from the bottom only using fork lift. Do not lift or strap to the upper half of machine. Machine is top heavy be sure to stabilize load during transport.

6 Page 6 Installation Electrical Refer to: 6SBTE150 Electrical Prints Before proceeding further with the installation, make sure that electrical power is: Domestic: 208 VAC, 10A, 60 Hz, 3ⱷ International: 400 VDC, 6A, 50 Hz, 3ⱷ Open the control panel: shown with optional international voltage. Visually check for shipping damage Pull test the wiring by gently tugging on all wiring at their connections Installation Piping Inlet Position the system to allow gravity drain from the generator to the Edger System. Maintain full pipe size with minimal bends. Maintain a minimum slope of ¼ per linear foot (2 cm/m) of pipe for good drainage. Do not use flexible hose for drain line. There are two inlets, one on each side of the tank. Water Inlet

7 Page 7 Outlet Water Outlet Connect supply piping to filters/edgers here. The flow monitor is installed to shut down the chip separator while Edgers are off line for an extended period of time. Flow Monitor Water Make-up Connect domestic water supply here. Minimum line pressure is 60psi (2.75 bar). The valve has a 1/2 NPT female thread (or BSPT conversion fitting). Domestic water Turn the system on, energizing the makeup valve. Water make up solenoid will turn off when fluid reaches the correct level.

8 Page 8 Air supply Connect 70 psi clean dry air. Air Chiller Supply (Temperature control optional) Shown with optional temperature control valve. Connect chilled water supply to coil here using hoses provided.

9 Page 9 Start-up Fill Tank Fill the tank with water. Total system volume approximately 80 liters (21 gal). Verify 70psi air to Filter/Regulator. Verify incoming voltage matches voltage rating on panel legend. Verify supply line to filters/edgers are secure. Verify fluid lines to chiller are secure. Turn on main breaker. Control Panel Functions Starting and Stopping Press the START button to place the system into operation. To normally stop the Edger, press the STOP button. Do not use the EMERGENCY STOP button for normal stopping. Starting the system will start the Water Supply Pump, and Chip Separator.

10 Page 10 Alarms When the alarm beacon is blinking, one of the following has occurred: Low Level Tank Alarm Tank level is below minimum height for extended amount of time. Check Water is not held up in the Chip Separator, press Start to initiate water makeup. Verify Water Make up is on and Water Make up Valve is operational. High Level Tank Alarm Tank level is above Maximum Height. Check Chip Separator and Edger Tank Screen for Held up water, clear if required. Lower water level in Tank. Clear High Level Alarm. Press green START button to Start Edger Tank Low Temperature Alarm Indicates Low Water Temperature. Check Chiller supply for correct temperature and flow to Edger, verify Chiller valve is operational. High Temperature Alarm Indicates High Water Temperature. Check Chiller supply for correct temperature and flow to Edger, verify Chiller valve is operational. Low Air Pressure Alarm Check supply of service air to machine. Ensure supply valve is open. Check pressure indication on air regulator. No Work Indicates No Water Flow to process supply; Chip Separator will go to standby mode. Chip Separator will automatically restart once Water Flow is resumed. Auto Fill Mode Start System in Auto mode; Press Green Start button to start Auto Fill Mode. Press Green Start button again to Fill Tank. Level Switch Error Check High and Low level switches are able to move freely in tank unobstructed. Motor Overload Indicates the motor overload relay has tripped. A qualified electrician should investigate. Consult electrical diagram or Bazell Technologies directly for more information.

11 Page 11 Overload Indicates a circuit breaker within the electrical panel has tripped. A qualified electrician should investigate. Consult electrical diagram or Bazell Technologies directly for more information. Emergency Stop Indicates red Emergency Stop button set; Reminds operator to reset button. Pull out Emergency Stop button to reset. Daily Product Startup Check air pressure gauge set to 70 psi Check chip separator bin empty if necessary Turn on Main Breaker and depress START Tank Cleaning Frequency of manual tank cleaning is determined by the volume of production - especially non-chip debris of plastics. Because the edgers use straight water without water additives there is the possibility of fungus or bacteria growing within the system. Any additive used must be compatible with the machine tool.

12 Page 12 Control Summary Function Start Stop Setup Calibration Push green START button. Push red STOP button. Push 1 for 2 seconds with system stopped. Push 2 for 2 seconds with system stopped. Setup Message Action Notes System Setup Password: _ Password 5066 Push " " Temperature Sets Control Temperature of Setpoint Water process (20.0 C) Bandwidth (2.0 C) Temperature Control Warning (5.0 C) Chip Separator (15min) No Flow Debounce (30 sec) Water Make up Duration (10 sec) Tank Auto Fill Duration (15 sec) Enter value, Push " " Push " " again to scroll to next screen Sets Max deviation of Temperature control band Sets Alarm Setpoint to 5.0 C of Setpoint Sets the brush actuator extended and retracted timer Timer for No Flow condition; turns Chip Separator Off. Automatically restarts with Flow to process. Timer for Auto Water Make up; Valve opens for timer value Timer for Auto Water Make up; Valve opens for timer value

13 Page 13 Calibration System Setup Password: _ Minimum 4mA Milliamp (4mA) Minimum Temperature (0.0 C) Maximum 20mA Milliamp (20mA) Maximum Temperature (100.0 C) Password 5066 Enter value, Push " " Push " " Push " " again to scroll to next screen Sets Minimum ma scaling Sets Minimum Temperature Sets Maximum ma scaling Sets Maximum Temperature Warnings, Alerts and Faults Edger Tank Low Level Edger Tank High Level Edger Tank Emergency Stop Edger Tank Air Pressure Low Auto Fill Mode Level Switch Error Electrical Overload No Work Tank water level is below minimum height for extended amount of time. Check Chip Separator or Edger Tank Screen for Held up water, clear if required. Press Start to initiate water makeup. Verify Water Make up is on and Water Make up Valve is operational. Tank water level is above Maximum Height. Check Chip Separator or Edger Tank Screen for Held up water, clear if required. Lower water level in Tank. Clear High Level Alarm. Press green START button to Start Edger Tank Indicates red Emergency Stop button set; Reminds operator to reset button. Pull out Emergency Stop button to reset. Indicates inadequate utility air supply; Protects operating without Chip Separator motive air. Check air pressure at regulator; Gauge on regulator should read 75PSI; Check building air supply valve open. Start System in Auto mode; Press Green Start button to start Auto Fill Mode. Press Green Start button again to Fill Tank. Check High and Low level switches are able to move freely in tank unobstructed. Indicates circuit breaker or motor overload tripped; Protects panel against valve solenoid or motor winding overcurrent condition. Refer to qualified electrical service personal; Disconnect power and inspect electrical panel; repair or replace offending load. Indicates no Water Flow to process supply;

14 Page 14 Low Temperature Alarm High Temperature Alarm Chip Separator will go to standby mode. Chip Separator will automatically restart once Water Flow is resumed. Indicates Low Water Temperature. Check Chiller supply for correct temperature and flow to Edger, verify Chiller valve is operational. Indicates High Water Temperature. Check Chiller supply for correct temperature and flow to Edger, verify Chiller valve is operational.

15 Page 15 Screen Cleaning Tilt screen to remove/replace. Flush screen thoroughly from the back side with water. If necessary brush the fine mesh (top side) of the screen with soft nylon bristle brush. Do not use a wire brush. Press cleaned screen firmly into place.

16 Page 16 Be sure the screen is firmly pressed against bottom stop. Be sure the screen is pressed firmly against the chip separator base.

17 Page 17 System Dimensions and Utilities Drawing 6SBTB001

18 Page 18 EDGER SYSTEM PROCESS FLOW Drawing # 6SBTE200

19 Page 19 Drawing # 6SBTE205

20 Page 20 System Parts List Refer to drawing 6SBTE205 ITEM QTY PART NO. DESCRIPTION MATERIAL/SPEC VDC SOLENOID VALVE SMC 24VDC BAZN110 CONTROL PANEL RELAY LOGIC FILTER/REG/PRESSURE SWITCH SMC AR AIR LIMIT VALVE SMC N-X AIR CYLINDER 50 X CON-6SATE001 POLYJECTOR CABINET 304SS AS2OY2000 FLOAT SWITCH N/O 8 1 P-KTF151/290 PUMP, BRINKMANN 3/4HP 190/380V 9 1 CON-6SBTE057A BRUSH ASSEMBLY INCLUDES 9A,B & C 9A 1 CON-6SBTE057 BRUSH BRACKET 304SS 9B 1 CON-6SATD027 BRUSH NYLON 9C 2 CON-6SATE022 GASKET BUNA AS2OY1200 FLOAT SWITCH N/O 11 4 T-CAST-4W779 CASTERS STEEL VDC SOLENOID, WATER MAKEUP ASCO ½ 24VDC SI5000 FLOW MONITOR IFM 24VDC 1 T-6SBTE030 SCREEN ASSEMBLY 304SS/NYLON MESH 1 T-170M76X76 SCREEN MESH NYLON 175MICRON 1 T-6SATW040 COOLING COIL COPPER ½

21 Page 21 Drawing # 6SBTE150

22 Page 22

23 Page 23

24 Page 24

25 Page 25

26 Page 26 Limitations of Warranty Bazell Technologies Corporation shall not be liable, to any extent whatsoever, for any damages resulting from or arising out of the use or performance of this product and related documentation or the procedures specified in this manual, regardless of foreseeability or the form of action, whether in contract, tort (including negligence), breach of warranty, strict liability or otherwise, and including but not limited to damages resulting from loss of data, loss of anticipated profits, or any special, indirect, incidental or consequential damages. In no even shall Bazell Technologies Corporation liability to the user exceed the amount paid by the user to Bazell Technologies Corporation hereunder. The user assumes full responsibility for the results obtained from the use of this product and related documentation and for application of such results. Document Representation This documentation is provided in good faith but without warranty as to correctness, accuracy, reliability, omissions, or otherwise except as provided in writing by an officer of Bazell Technologies Corporation. Contacting Bazell Technologies Bazell Technologies Corporation 5066 Commercial Circle Concord, CA Tel: (925) Fax: (925) web: