Preliminary specification

Transcription

1 Deep UV LED - 340nm UV CA3535 series (CUD4GF1A) CUD4GF1A RoHS Product Brief Description CUD4GF1A is a deep ultraviolet light emitting diode with peak emission wavelengths from 340nm to 345nm. It incorporates state of the art SMD design and low thermal resistance. CUD4GF1A is designed for curing, deodorization, phototherapy and Spectroscopy for Medical and Scientific application. Features and Benefits Deep ultraviolet LED Low thermal resistance SMT solderable Lead Free product RoHS compliant High Luminous intensity Long Operation Life Power Package Application Key Applications Blood Analysis Phototherapy Spectroscopy for Medical & Scientific application Deodorization Preliminary specification 1

2 Table of Contents Index Product Brief Table of Contents Performance Characteristics Mechanical Dimensions Recommended Solder Pad Reflow Soldering Characteristics Handling of Silicone Resin for LEDs Precaution for Use Company Information 2

3 Performance Characteristics Table 1. Electro - Optical characteristic at 500mA (T a =25, RH=30%) Parameter Symbol Value Unit Peak wavelength [1] λ p 343 nm Radiant Flux [2] Φ e [3] 45 mw Forward Voltage [4] V F 4.3 V Spectrum Half Width Δ λ - nm View Angle 2Θ 1/2 - deg. Table 2. Absolute Maximum Rating Parameter Symbol Value Min. Typ. Max. Unit Forward Current I F ma Power Dissipation P D mw Operating Temperature T opr ºC Storage Temperature T stg ºC Thermal resistance (J to S) [5] Rθ J-S - - ºC/W Notes : 1. Peak Wavelength Measurement tolerance : ±3nm 2. Radiant Flux Measurement tolerance : ± 10% 3. Φ e is the Total Radiant Flux as measured with an integrated sphere. 4. Forward Voltage Measurement tolerance : ±3% 5. Rθ J-S is the thermal resistance between chip junction to solder. 3

4 Mechanical Dimensions Notes : [1] All dimensions are in millimeters. [2] Scale : none [3] Undefined tolerance is ±0.2mm 4

5 Recommended Solder Pad Notes : [1] All dimensions are in millimeters. [2] Scale : none [3] This drawing without tolerances is for reference only 5

6 Reflow Soldering Characteristics Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly Average ramp-up rate (Ts_max to Tp) 3 C/second max. 3 C/second max. Preheat - Temperature Min (Ts_min) - Temperature Max (Ts_max) - Time (Ts_min to Ts_max) (ts) Time maintained above: - Temperature (TL) - Time (tl) 100 C 150 C seconds 150 C 200 C seconds 183 C seconds 217 C seconds Peak Temperature (Tp) Time within 5 C of actual Peak Temperature (t) seconds seconds Ramp-down Rate 6 C/second max. 6 C/second max. Time 25 C to Peak Temperature 6 minutes max. 8 minutes max. * Caution 1. Reflow soldering should not be done more than one time. 2. Repairs should not be done after the LEDs have been soldered. When repair is unavoidable, suitable tools must be used. 3. Die slug is to be soldered. 4. When soldering, do not put stress on the LEDs during heating. 5. After soldering, do not warp the circuit board. 6. Recommend to use a convection type reflow machine with 7 ~ 8 zones. 6

7 Handling of LEDs (1) During processing, mechanical stress on the surface should be minimized as much as possible. Sharp objects of all types could crack the sealing compound. (2) In general, LEDs should only be handled from the side. Grabbing the top window part could cause damaging or cracking of the window. (3) Glass can be damaged by force. a. Be careful not to touch the lens with tweezers or sharp tools. The lens can be shattered or fall apart. b. The product can break when it falls. c. If products were stacked after SMT, the product can be damaged. (4) Be careful with process that CA3535 series can be contaminated by foreign materials(particles, fume, gas, etc). (5) When populating boards in SMT production, there are basically no restrictions regarding the form of the pick and place nozzle, except that mechanical pressure on the surface of the resin must be prevented. This is assured by choosing a pick and place nozzle which is larger than the LED s reflector area. (6) This device is not allowed to be used in any type of fluid such as water, oil, organic solvent, etc. Ultrasonic cleaning is not recommended. Ultrasonic cleaning may cause damage to the LED. (7) Please do not mold this product into another resin (epoxy, urethane, etc) and do not handle this product with acid or sulfur material in sealed space. (8) Avoid leaving fingerprints on glass lens parts. 7

8 Precaution for Use (1) Storage To avoid the moisture penetration, we recommend storing LEDs in a dry box with a desiccant. The recommended storage temperature range is 5 to 30 and a maximum humidity of RH50%. (2) Use Precaution after Opening the Packaging Use proper SMD techniques when the LED is to be soldered dipped as separation of the lens may affect the light output efficiency. Pay attention to the following: a. Recommend conditions after opening the package - Sealing / Temperature : 5 ~ 30 Humidity : less than RH60% b. If the package has been opened more than 7days (MSL 3) or the color of the desiccant changes, components should be dried for 10-24hr at 65±5 c. Baking should only be done once. (3) Do not apply mechanical force or excess vibration during the cooling process to normal temperature after soldering. (4) Do not rapidly cool device after soldering. (5) Components should not be mounted on warped (non coplanar) portion of PCB. (6) Radioactive exposure is not considered for the products listed here in. (7) This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When washing is required, IPA (Isopropyl Alcohol) should be used. (8) When the LEDs are in operation the maximum current should be decided after measuring the package temperature. (9) LEDs must be stored in a clean environment. We recommend LEDs store in nitrogen-filled container. (10) The appearance and specifications of the product may be modified for improvement without notice. 8

9 Precaution for Use (11) VOCs (Volatile organic compounds) emitted from materials used in the construction of fixtures ca n penetrate silicone encapsulants of LEDs and discolor when exposed to heat and photonic energy. T he result can be a significant loss of light output from the fixture. Knowledge of the properties of the m aterials selected to be used in the construction of fixtures can help prevent these issues. (12) The slug is electrically isolated. (13) Attaching LEDs, do not use adhesives that outgas organic vapor. (14) The driving circuit must be designed to allow forward voltage only when it is ON or OFF. If the rev erse voltage is applied to LED, migration can be generated resulting in LED damage. (15) LEDs are sensitive to Electro-Static Discharge (ESD) and Electrical Over Stress (EOS). Below is a list of suggestions that Seoul Viosys purposes to minimize these effects. a. ESD (Electro Static Discharge) Electrostatic discharge (ESD) is the defined as the release of static electricity when two objects come into contact. While most ESD events are considered harmless, it can be an expensive problem in many industrial environments during production and storage. The damage from ESD to an LEDs may cause the product to demonstrate unusual characteristics such as: - Increase in reverse leakage current lowered turn-on voltage - Abnormal emissions from the LED at low current The following recommendations are suggested to help minimize the potential for an ESD event. One or more recommended work area suggestions: - Ionizing fan setup - ESD table/shelf mat made of conductive materials - ESD safe storage containers One or more personnel suggestion options: - Antistatic wrist-strap - Antistatic material shoes - Antistatic clothes Environmental controls: - Humidity control (ESD gets worse in a dry environment) 9

10 Precaution for Use b. EOS (Electrical Over Stress) Electrical Over-Stress (EOS) is defined as damage that may occur when an electronic device is subjected to a current or voltage that is beyond the maximum specification limits of the device. The effects from an EOS event can be noticed through product performance like: - Changes to the performance of the LED package (If the damage is around the bond pad area and since the package is completely encapsulated the package may turn on but flicker show severe performance degradation.) - Changes to the light output of the luminaire from component failure - Components on the board not operating at determined drive power Failure of performance from entire fixture due to changes in circuit voltage and current across total circuit causing trickle down failures. It is impossible to predict the failure mode of every LED exposed to electrical overstress as the failure modes have been investigated to vary, but there are some common signs that will indicate an EOS event has occurred: - Damaged may be noticed to the bond wires (appearing similar to a blown fuse) - Damage to the bond pads located on the emission surface of the LED package (shadowing can be noticed around the bond pads while viewing through a microscope) - Anomalies noticed in the encapsulation and phosphor around the bond wires. - This damage usually appears due to the thermal stress produced during the EOS event. c. To help minimize the damage from an EOS event Seoul Viosys recommends utilizing: - A surge protection circuit - An appropriately rated over voltage protection device - A current limiting device 10

11 Company Information Published by Seoul Viosys 2013 All Rights Reserved. Company Information Seoul Viosys () manufactures light emitting diodes (LEDs) with a full range of UV wavelengths from UVC to UVA (under 400nm) for Industrial Curing, Air/Water Purification, Disinfection and Home appliance. The company is one of the world leading UV LED supplier, holding more than 4,000 patents globally, while offering various kinds of LED technologies and application-solutions in High power UV LED, UV sensor, UV LED Lamp and variety of UV LED sourced Applications. The company's broad product portfolio includes hybrid modules for unique applications such as UV disinfection, deodorization, UV purification as well as customized modules for your Application. Legal Disclaimer Information in this document is provided in connection with Seoul Viosys products. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Seoul Viosys hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. The appearance and specifications of the product can be changed to improve the quality and/or performance without notice. 11