Equipment for Research Analysis Process Education. page J13. page J3, J3, J4. page J14, J15, J16. page J8, J9, J10. page J5. page J10, J22.

Transcription

1 page J12 page J20, J21 page J11 page J3, J3, J4 page J5 page J14, J15, J16 page J8, J9, J10 page J13 page J25 page J5 page J10, J22 page J19 page J9, J10 page J23, J24 page J18 page J6, J7 page J17 page J3, J6, J12, J13 page J26 page J27 Equipment for Research Analysis Process Education

2 Heating mantles mod. 102E Controller mod. E Class 300 Heating mantles with incorporated power controllers Aluminum casings, epoxy finishing, easy substitution of heating unit (non disposable equipment) of fiberglass and nickel-chromium resistance, for use with round-bottom balloons and 300ºC maximum use temperature, with electronic power controller that acts on impulse with adjustable time, indicated by a pilot lamp. Reinforced thermal insulation which makes for optimum yield, safety, and power-saving Homogenous heat distribution, due to its well-designed project, achieving better heating yield and preventing balloon breaks pads with incorporated power controllers Model 11E 12E 22E 52E 102E 202E Capacity (L) Power (W) Feed 115 or 230 V, Hz mod. 102 Class 300 Heating mantles Aluminum casing, epoxy finishing, easy substitution of heating unit (non disposable equipment) of fiberglass and nickel-chromium resistance, for use with round-bottom balloons and 300ºC maximum use temperature. Reinforced thermal insulation which makes for optimum yield, safety, and power-saving Homogenous heat distribution, due to its well-designed project, achieving better heating yield and preventing balloon breaks Models 1212, 1202, 2422, 2402, with two heating zones Model 5003 with three heating zones For greater durability use temperature controller mod. 407, 408, or mod. 411 (not included) mod Model Capacity (L) Ø balloon - mm* Power (W) Feed 115 or 230 V, Hz 230 V, Hz * According to the ISO 1773 and ASTM 1403 standards, except models 2422, 2402, and Bottom opening supplied on request Splash Guards Splash guards made of silicone, to be used on the heating mantles, helping to prevent damages caused by the spilling of chemicals inside the equipment and improving operational safety when working with flammables. Maximum temperature supported 200 C. Model For use with the heating pad models , 12E, 22E, 12M, 22M, 22-6, 27, , 52E, 102, 102E, 52M, 102M, 52-6,102-6, 105,107, , 202E, 202M, , 652, , , 2402 J2

3 Heating mantles Class 650 heating mantles Aluminum casings, epoxy finishing, heating element and quartz insulation for use with round-bottom balloons and 500ºC maximum use temperature. Power controller mod. 407 included Available in 115 or 230 V, Hz Model Capacity (L) Power (W) Class 650 Class 300 heating mantles with stirring A set comprised of a heating pad and a magnetic stirring device. Injected aluminum casing, epoxy finishing, heat unit easy to replace (nondisposal equipment) of fiberglass and nickel-chromium resistance, for use with round-bottom balloons and 300ºC maximum use temperature, and stirring device motor fitted in the chassis. Temperature and rotations are electronically controlled with rotation ranging from 100 to r/min. Available in either 115 or 230 V, 50 60Hz Supplied with two oval magnetic bars for models 12M, 22M and three bars for models 52M, 102M and 202M Model 12M 22M 52M 102M 202M Capacity ( ml ) Power (W) Class 300 multi-unit of mantles (Extractor) Steel-plated body, epoxy finishing, heating unit easy to replace (nondisposal equipment) in fiberglass and nickel-chromium resistance, for use with round-bottom balloons, 300ºC maximum use temperature, and built-in individual temperature control. Supplied with 2 columns and hooked support and aluminum rod connectors Model Capacity (L) 3 x x x x x 1 6 x 1 Dimensions (cm) 60 x 25 x x 25 x x 25 x x 25 x x 30 x x 30 x 18 Power (W) Tensão 115 or 230V, Hz 230V, Hz Class 300 spherical heating mantles With excellent balloon heating, a set comprised of a class 300 heating pad, aluminum casing, epoxy finishing, easy substitution of heating unit (nondisposal equipment) in fiberglass and nickel-chromium resistance, and semi-spherical pad on top, built in anti-flame fabric with elliptical opening covering up to 3 joins, internally in fiberglass and nickel-chromium resistance, for use with round-bottom balloons and 300 C maximum operating temperature, joined by three fasteners. Available in 115 or 230 V For more durability use temperature controller mod or mod. 411 (not included) Model Capacity (L) Power (W) Pads with higher capacities can be provided. J3

4 Heating mantles Class 300 top semi-spherical heating mantles Anti-flame fabric body with elliptical opening covering up to 3 joints, internally in fiberglass and nickel-chromium resistance, for use with round-bottom balloons and 300 C maximum operational temperature. Available in either115 or 230 V, Hz For more durability working Model temperature controller mod. 407 Capacity (L) or mod. 411 (not included) Power (W) Class 300 funnel type heating mantles Aluminum casing, epoxy finishing, heating unit easy to replace (non-disposable equipment) in fiberglass and nickel-chromium resistance, for use with analyticallyshaped funnel at a 60º angel (no tap) and 300ºC maximum operational temperature. For more durability working temperature controller mod. 407 or mod. 411 (not included) Available in either 115 or Model 22F 102F 230 V, Hz Ø top cm 9 to to 20 Hook with silicone brackets to be fixed to the support Power (W) Heating mantles for Beaker low pan and Kettle (reactor) Class 300 Aluminum casing, epoxy finishing, heating unit easy to replace (non-disposable equipment) in fiberglass and nickel-chromium resistance, for use with Beaker or Kettle (reactor), accommodating 80% of the flask height. Operates at temperatures of up to 300ºC Mod. 407 power controller included Available in either 115 or 230 V, Hz Beaker Kettle reator Model Diameter (mm) Capacity (L) 0,25 0,4 0, ,5 1 2 Power (W) Class 350 heating mantles (with shielded resistance) with coolant Aluminum casing, epoxy finishing, reinforced fiberglass heating unit with stainless steel mesh and shielded resistance, for use with round-bottom balloons, 350ºC maximum operational temperature. For more durability working temperature controller mod. 407 or mod. 411 (not included) Available in either 230 V, Hz Interspersed with copper serpentine allowing for coolant circulation with temperature of up to 20ºC. We recommend the liquid coolant Fisatom mod. 850 (not included). mod. 102K Model 102K 202K 302K 652K Capacity (L) Potência (W) J4

5 Heating mantles Heating tapes Flexible, they are suitable for heating or maintaining the temperature of metal or glass tubing, edges with anchoring cords and plug. Made in fiberglass with incorporated double-insulation resistance For more durability working temperature controller mod. 407, 408 or 409 (not included) Model 5 Class 300 Standard Maximum operating temperature: 300ºC Model 9 Class 200 Maximum operating temperature: 200ºC Lined with silicone rubber, recommended for damp environments or environments with gases models 5 & 9 Width (cm) * * 2.5* 5 5 5* 5* Length (m) Power (W) * Available only in 230 V - others in 115 or 230 V, Hz Model 7 Class 300 Round Recommended for application on small diameter tubing and plugs, made in fiberglass fabric with incorporated double-insulation resistance. Flexible, edges with anchoring cords and plugs Maximum operational temperature: 300ºC For more durability working temperature controller mod. 407 (not included) Available in either 115 or 230 V, Hz Diameter (mm) 5 5 Length (cm) Power (W) Power controller for heating mantles and tapes Electronic power controller that acts on time variable electrical impulses, monitored by a pilot lamp. Ideal for heating mantles and tapes. Regulates temperatures over 50ºC Bivolt Degree of protection IP21 Model 407 Maximum power of 1150 W in 115 V or 2300 W in 230 V, Hz Model 408 Maximum power of 1800 W in 115 V or 3600 W in 230 V, Hz, which may be used with pads with two zones of up to 10 A each mod. 407 Model 409 Maximum power of 1800 W in 115 V or 3600 W in 230 V, Hz, with a 20 A outlet mod. 408 e 409 Temperature controller mod. 411 Temperature controlled by PID system with digital display (environment +5ºC to 400ºC), auto-tuning, alarm, and 0.1ºC resolution. 35 cm stainless steel temperature probe with Pt100 sensor with flexible cable Available in either 115 V 1150 W or 230 V 2300 W, Hz. Supplied with a rear shaft for fixation to the support Degree of protection IP21 Optional: 25 or 45 cm temperature probe 24/40 or 29/42 PTFE Conical plug for probe Support mod ; rod connector mod. 470, and Calibration certificate The Fisatom heating mantles with connected controller model E must not be used with the controller mod. 407, 408 and 411. J5

6 Hot plates Hot plate Models 501, 502 & 503 up to 360ºC Injected aluminum hot plate with embedded shielded resistance, making for uniform temperature across the plate extension, temperature controlled by capillary thermostat from 50 to 360ºC, pilot lamp, built externally of epoxy lined aluminum sheet. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the hot plate) Available in either 115 or 230 V, Hz Degree of protection IP23 mod. 501, 502 and 503 Model Plate diameter (cm) Power (W) mod and Multi-units of round hot plates with 2 assays up to 360ºC Injected aluminum hot plate with embedded shielded resistance, making for uniform temperature across the plate extension, individual temperature control by capillary thermostat from 50 to 360ºC, pilot lamp, built externally of epoxy lined steel sheet. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the hot plate) Degree of protection IP23 Model W x D x H (cm) 34 x 20 x x 21 x 10.5 Assays 2 x 1 L 2 x 2 L Power (kw) Voltage 115 or 230 V, Hz Multi-units of round hot plates with 3 or 6 assays up to 360ºC Ideal for Soxhlet extractors which use flat-bottom balloon flasks. Injected aluminum hot plate with embedded shielded resistance, making for uniform temperature across the plate extension, individual temperature control by capillary thermostat from 50 to 360ºC, pilot lamp, built externally of epoxy lined steel sheet. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the hot plate) Degree of protection IP23 Supplied with 2 columns, 1 horizontal support with clamps and rod connectors (made of aluminum) mod Model W x D x H (cm) 79 x 20 x x 20 x x 20 x x 21 x x 21 x 10.5 Assays 6 x 0.5 L 3 x 1 L 6 x 1 L 3 x 2 L 6 x 2 L Power (kw) Voltage 115 or 230 V, Hz 230 V, Hz J6

7 Hot plates Square hot plates mod. 509 & 510 up to 360ºC Injected aluminum hot plate with embedded shielded resistance, making for uniform temperature across the plate extension, temperature controlled by capillary thermostat from 50 to 360ºC, pilot lamp, built externally of epoxy lined steel sheet. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the hot plate) Degree of protection IP23 mod. 509 Model W x D x H (cm) 31 x 31 x x 31 x 18 Power (kw) 1,6 3,2 Voltage 115 ou 230V 230V mod. 510 Square hot plates with digital control mod. 509 & 510 up to 350ºC Injected aluminum hot plate with embedded shielded resistance, making for uniform temperature across the plate extension, temperature controlled by PID system, with digital display (environment +5ºC to 350ºC), 0.1ºC resolution, built externally of epoxy lined steel sheet. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the hot plate) Alarm and auto-tuning Degree of protection IP25 Optional: Calibration Certificate mod. 509D Model 509D 510D W x D x H (cm) 31 x 31 x x 31 x 18 Power (kw) Voltage 115 or 230 V 230 V mod. 510D Fulkontrol This is a high temperature heater (replaces the flame heater). The heating element is built of refractory ceramics, nickel-chromium resistance, unit easy to replace, housed in a frame Rear fixation shaft Reversible ceramic support plate that allows for the accommodation of ml balloons, or 500, 650, 800 ml Kjeldahl flasks for the purpose of fixation of either the device or the flask Adjustable power from 10 to 800 W Available in either 115 or 230 V, Hz Model 500 Traditional 14 x 14 x 30 cm Model 500F Lower cost, ø 15 x 14,5 cm mod. 500 mod. 500F J7

8 Thermostatic baths Lid is optional mod. 550 Thermostatic bath mod. 550 Epoxy lined aluminum casing, Ø 25 x 12 high stainless steel round tub capable of holding up to 4 liters, controlled by capillary thermostat with control ranging from 50 to 120ºC and ± 2ºC capacity, pilot lamp, 1200 W power. Internal platform supplied Degree of protection IP02 Available in either 115 or 230 V, Hz Optional: 4-ring cover mod. 553 Thermostatic bath mod. 553 Epoxy lined aluminum casing, Ø 25 x 12 high stainless steel round tub capable of holding up to 4 liters, controlled by capillary thermostat with control ranging from 50 to 120ºC and ± 2ºC capacity, pilot lamp, power of 1200 W. Internal platform supplied Thermal insulation Degree of protection IP02 Available in either 115 or 230 V, Hz Optional: 4-ring cover mod. 557 Thermostatic bath mod. 557 Epoxy lined aluminum casing, Ø 25 x 12 cm high stainless steel round tub capable of holding up to 4 liters, thermal insulation, temperature controlled by PID system with digital display (environment +5ºC to 175ºC), stability of ±0.5ºC, alarm, auto-tuning, and resolution of 0.1ºC. Power of 1200 W Internal platform supplied Degree of protection IP02 Available in either 115 or 230 V, 50 or 60 Hz Optional: 4-ring cover mod. 558 Thermostatic bath mod. 558 Epoxy lined aluminum casing, Ø 24 x 11 cm high stainless steel semi-spherical tub, capable of holding up to 3 liters, thermal insulation, temperature controlled by PID system with digital display (environment +5ºC to 150ºC), stability of ±0.5ºC, Pt100, alarm, auto-tuning, and resolution of 0.1ºC. Power of 1000 W with built-in resistance (makes cleaning easier) Degree of protection IP02 Available in either 115 or 230 V, 50 or 60 Hz Optional: 4-ring cover mod. 555 Thermostatic bath mod. 555 With magnetic stirring, electronic rotation control from 150 to 1200r/min. Epoxy lined aluminum casing, Ø 25 x 12 cm high stainless steel round tub, capable of holding up to 4 liters, thermal insulation, controlled by capillary thermostat, control ranging from 50 to 120ºC, and stability of ±2ºC. Power of 1200 W Internal platform and 3 magnetic bars supplied Degree of protection IP02 Available in either 115 or 230 V, Hz Optional: 4-ring cover J8

9 Thermostatic baths Thermostatic bath line up to 95ºC Mod. 562 Epoxy lined metal casing, stainless steel tub for up to 6 L, dimensions 29 x 15 x 15 cm. Temperature controlled by PID system with digital display (environment +5ºC to 95ºC), resolution of 0.1ºC, stability of ±0.5ºC, alarm and auto-tuning. Drain and internal platform supplied Available in either 115 or 230 V, 50 or 60 Hz, 900 W Mod. 562S Epoxy lined metal casing, stainless steel tub for up to 6 L, dimensions 29 x 15 x 15 cm. Temperature controlled by PID system with digital display (environment +5ºC to 95ºC), resolution of 0.1ºC, stability of ±0.5ºC, alarm and auto-tuning. Drain, internal platform, cover and stand mod supplied Available in either 115 or 230 V, 50 or 60 Hz, 900 W mod. 562 & 562S Mod. 572 Epoxy lined metal casing, stainless steel tub for up to 20 L, dimensions 49 x 29 x 15 cm. Temperature controlled by PID system with digital display (environment +5ºC to 95ºC), resolution of 0.1ºC, stability of ±0.5ºC, alarm and auto-tuning. Drain and internal platform supplied Available in either 115 or 230 V, 50 or 60 Hz, 1400 W Mod. 572S Epoxy lined metal casing, stainless steel tub for up to 20 L, dimensions 49 x 29 x 15 cm. Temperature controlled by PID system with digital display (environment +5ºC to 95ºC), resolution of 0.1ºC, stability of ±0.5ºC, alarm and auto-tuning. Drain, internal platform, cover and stand mod supplied Available in 230 V, 50 or 60 Hz, 1400 W Optional Polyethylene shelves for 10 cm high test tubes: Mod for 85 tubes measuring Ø 10 to 13 cm Mod for 50 tubes measuring Ø 14 to 16 cm Mod for 24 tubes measuring Ø 18 to 22 cm Mod Stainless steel cover for baths mod. 562 and 562S (mandatory at temperatures >80ºC) Mod Stainless steel cover with 6 openings and 6 reduction sets with 4 removable rings each Mod Bath level (patented). Keeps the desired water level in the tub without wasting. Includes a magnet for fixation onto the bath casing Calibration certificate Thermostatic bath line up to 175ºC Mod. 578 Epoxy lined metal casing, stainless steel tub for up to 20 L, dimensions 49 x 29 x 15 cm. Temperature controlled by PID system with digital display (environment +5ºC to 175ºC), resolution of 0.1ºC, stability of ±0.5ºC, alarm and auto-tuning. Drain and internal platform supplied Available in 230 V, 50 or 60 Hz, 2000 W Mod. 588 Epoxy lined metal casing, stainless steel tub for up to 28 L, dimensions 49 x 29 x 20 cm. Temperature controlled by PID system with digital display (environment +5ºC to 175ºC), resolution of 0.1ºC, stability of ±0.5ºC, alarm and auto-tuning. Drain and internal platform supplied Available in 230 V, 50 or 60 Hz, 2000 W Optional Mod Stainless steel cover with 6 openings and 6 reduction sets with 4 removable rings each Mod Stainless steel cover for bath mod. 578 and 588 Calibration certificate mod. 572 & 572S mod mod (entry by hole) mod. 578 & 588 mod and mod mod mod J9

10 Thermostatic baths mod mod. 577 & 587 mod Thermostatic baths with circulation Mod. 577 Epoxy lined metal casing, stainless steel tub for up 20 L, dimensions 32 x 29 x 15 cm. Circulation pump of 6 L/m. Temperature controlled by PID system with digital display (environment +5ºC to 175ºC), resolution of 0.1ºC, stability of ±0.5ºC, Pt100, safety thermostat against dry operation, alarm and auto-tuning. Drain and internal platform supplied Available in 230 V, 60Hz, 1400 W Mod. 587 Epoxy lined metal casing, stainless steel tub for up 28 L, dimensions 32 x 29 x 20 cm. Circulation pump of 6L/m. Temperature controlled by PID system with digital display (environment +5ºC to 175ºC), resolution of 0.1ºC, stability of ±0.5ºC, Pt100, safety thermostat against dry operation, alarm and auto-tuning. Drain and internal platform supplied Available in 230 V, 60Hz, 1800 W Optional Mod Stainless steel cover with 4 openings and 4 reduction sets with 4 removable rings each Mod Stainless steel cover mod. 597 Immersion thermostat with circulation Mod. 597 Enables fixation to a recipient up to 3cm thick and at least 15 cm deep. Epoxy lined metal casing shielded against vapors, safety thermostat against dry operation, circulation pump of 6L/m, flow control valve. Microprocessed temperature control by PID system digital display (environment +5ºC to 175ºC), resolution of 0.1ºC, stability of ±0.5ºC, Pt100, alarm and auto-tuning. Available in 230 V, 50 or 60 Hz, 1500 W Calibration certificate optional mod mod. 860 Thermostatic bath with refrigeration and circulation Mod. 860 Refrigerates or heats up within the temperature range from -20ºC to 95ºC, enabling outside circulation with variable flow, drain. Epoxy lined metal casing, hermetic compressor with ecologic gas and 9L stainless steel tub with useful space of 29 x 24 x 15 cm. Circulation pump of 6L/m and flow control valve. Microprocessed temperature control by PID system digital display (environment -20ºC to 95ºC), resolution of 0.1ºC, stability of ±0.5ºC, Pt100, alarm and auto-tuning. Available in 230 V, 60 Hz Optional Calibration certificate Lab Table mod. 455 (see page J18) External immersion serpentine mod Enables the fixation to a recipient of up to 3 cm and at least 15 cm deep Control with adjustable ramp mod. 455 J10

11 Magnetic stirrer Magnetic stirrer (electronic) Model 751 Inject aluminum and epoxy lined casing, 4.5 cm high. Robust equipment, stirs up to 1 L Fully electronic, without mobile components Revolution range: 50 to 1200 r/min. One 7 x 25 mm magnetic bar supplied Available in either 115 or 230 V, 50 or 60 Hz Degree of protection IP63 mod. 751 Magnetic stirrer without heating Models 752, 753 & 754 Inject aluminum and epoxy lined casing for more durability and robustness, aluminum cover, linear electronic revolution control, and pilot lamp. Available in either 115 or 230 V, 50 or 60 Hz Degree of protection IP63 Optional: 30 cm rear shaft Model Stirs up to 6 L 12 L 20 L Ø of cover 14 cm 18 cm 18 cm Height 10 cm 11.5 cm 11.5 cm Revolution range (r/min) 100 to to to 1500 Power 25 W 40 W 60 W Supplied with magnetic bars Ø x length (mm) 9 x 25 9 x 25 9 x x x x x 76 mod. 752, 753 & 754 Magnetic stirrer with heating Models 752A, 753A & 754A Inject aluminum and epoxy lined casing for more durability and robustness, with aluminum heating plate. Embedded shielded resistance, reaching uniform temperature across the plate, temperature controlled by a capillary thermostat ranging from 50 to 360ºC, liner electronic revolution control, and pilot lamp. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the heating plate) On-off switch (rear) Available in either 115 or 230 V, 50 or 60 Hz Degree of protection IP23 Optional: 30cm rear shaft Model 752A 753A 754A Stirs up to 4 L 10 L 14 L Ø of cover 14 cm 18 cm 18 cm Height 10 cm 11.5 cm 11.5 cm Revolution range (r/min) 100 to to to 1500 Power 650 W 1050 W 1060 W Supplied with magnetic bars Ø x length (mm) 9 x 25 9 x 25 9 x x x x x 76 mod. 752A, 753A & 754A J11

12 Magnetic stirrer Magnetic stirrer with digital heating (plate and product temperature control) Model 753D Inject aluminum and epoxy lined casing for more durability and robustness, with aluminum heating plate. Embedded shielded resistance, reaching uniform temperature across the plate, digital revolution and temperature control. Allows for temperature control in the plate or of the stirred product through an external sensor. Safety Thermal Fuse Temperature controlled by PID system from 50ºC to 300ºC Supplied with a 20 cm stainless steel external temperature probe, with Pt100 sensor, 30 cm rear shaft, 3 magnetic bars or 9 x 25, 9 x 39 and 11 x 54 (Ø x length in mm) and clamps mod. 462 and 470 Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the heating plate) Available in either 115 or 230 V, 50 or 60 Hz Alarm and auto-tuning Degree of protection IP22 Optional: Calibration Certificate mod. 753D Model Stirs up to Ø of plate Height Revolution range Power 753D 12 L 18 cm 11.5 cm 120 to r/min 1050 W Multi-unit of magnetic stirrer Models 752-3, and without heating Steel plate and epoxy lined casing, set of 3 or 6 magnetic stirrer, linear electronic control of individual revolution, pilot lamp, 2 column, 1 horizontal support, aluminum clamps and rod connectors. Available in either 115 or 230 V, Hz Degree of protection IP23 Model Stirs up to Ø of plate Revolution (r/min) Power Dimensions (cm) Supplied with magnetic bars Ø x length. (mm) x 6 L 14 cm 100 to W 50.5 x 22 x x 25 parts x 6 L 14 cm 100 to W 101 x 22 x x 25 parts x 12 L 18 cm 100 to W 63 x 26 x x 25 parts / 3 9 x 39 parts / 3 11 x 54 parts mod Models 752A-3, 752A-6 and 753A-3 with heating Steel plate and epoxy lined casing. Set of 3 or 6 injected aluminum heating plates with imbedded shielded resistance, temperature controlled by capillary thermostat from 50 to 360ºC, linear electronic control of individual revolution, pilot lamp, 2 columns, 1 horizontal support, aluminum clamps and rod connectors. Three-line cable with rubber ground wire as per the IEC regulation (prevents damages to the network when touching the heating plate) Available in 230V, Hz Degree of protection IP23 mod. 752A-6 Model Stirs up to Ø of plate Revolution (r/min) Power Dimensions (cm) Supplied with magnetic bars Ø x length. (mm) 752A-3 3 x 4 L 14 cm 100 to kw 50.5 x 22 x x 25 parts 752A-6 6 x 4 L 14 cm 100 to kw 101 x 22 x x 25 parts 753A-3 3 x 10 L 18 cm 100 to kw 63 x 26 x x 25 parts / 3 9 x 39 parts / 3 11 x 54 parts J12

13 Magnetic stirrer Magnetic stirrer (electronic) Model assay multi-unit, steel plated casing with epoxy finishing Digital display of revolution Stirs up to 5 assays of 800 ml each, electronic control, smooth without mobile components Revolution range: 50 to 1000 r/min Supplied with five 7 x 25 mm magnetic bars Dimensions: 4.5 x 59 cm Degree of protection IP52 Bivolt: V, Hz mod Stir bars Chemical-resistant PTFE-coated magnetic bar, of high durability, no weld, single mold, preventing penetration of products inside (impermeable), non-disposable, with high-intensity alnico V magnets. Resistant to temperatures from -270 to +260ºC Triangular 14 x 15 x 50 mm 13 x 13 x 40 mm 10 x 10 x 25 mm Egg-shaped Recommended round-bottom balloon flasks 500 ml ou mais - 14 x ml - 10 x ml - 8 x 20 Octagonal 11 x 54 mm 9 x 39 mm 9 x 25 mm For viscous products 16 x 100 mm 13 x 80 mm 13 x 65 mm 10 x 50 mm 9 x 40 mm 9 x 30 mm With spinning ring 16 x 80 mm 14 x 76 mm 11 x 54 mm 9 x 39 mm 9 x 25 mm Without spinning ring 7 x 50 mm 7 x 40 mm 7 x 30 mm 7 x 25 mm 7 x 20 mm 5 x 15 mm 3 x 10 mm 3 x 5 mm Glass Glass lined 10 x 30 mm Stir bar retriever 13 x 350 mm Angular 14 x 61 mm 10 x 38 mm 8 x 22 mm Colored 7 x 30 mm (blue) 9 x 25 mm (red) 7 x 20 mm (yellow) Spatula 20 x 20 x 260 mm Double stir bars For test tubes 22 mm Measurement tolerance ± 1 mm J13

14 Overhead stirrers/mixers Model D Stirs (water) up to 1.5 L up to 6 L up to 20 L up to 25 L up to 25 L up to 60 L up to 150 L Revolution range r/min r/min r/min Range r/min or Range r/min r/min r/min r/min r/min Power consumption 25 W 50 W 70 W 70 W 73 W 255W 350 W Useful power 1 W 4 W 16 W 16 W 16 W 60 W 155 W Digital tachometer No No No No Yes Yes Yes Revolutions control By Tyristor With microprocessor and torque control Friction disc + two-range gearbox Torque (approximated) 0,25 N.cm 5 N.cm 5 / 90 N.cm 5 / 90 N.cm N.cm N.cm N.cm N.cm Noise output 51 db 51 db db db db db db Overload warning Não Não Sim Sim Sim Não Não Optional support Weight 0,8 kg 1,2 kg 2,5 kg 3,02 kg 3,05 kg 6,6 kg 8,3 kg Supplied with Shaft with blade propeller Shaft with a 6cm Ø naval propeller 60 cm shaft with 12 cm Ø naval propeller mod. 710 Stirs up to 1.5 liters of water Overhead stirrer model 710 Suitable for stirring liquids whose viscosity is up to 100 mpas, revolution regulated by electronic circuit, injected aluminum casing, epoxy lined aluminum cover. Supplied with Ø 1/4 x 18 cm shaft with 5 cm stainless steel blade propeller The stirring capacity depends on the product type, as a reference it stirs up to 1.5 L of water Available in either 115 or 230 V, Hz Degree of protection IP43 Optional: support and rod connector mod. 711 Overhead stirrer model 711 Suitable for stirring liquids whose viscosity is up to 1000 mpas, revolution regulated by electronic circuit, injected aluminum casing, epoxy lined aluminum cover. Supplied with Ø 1/4 x 18 cm shaft with 6 cm Ø stainless steel naval propeller The stirring capacity depends on the product type, as a reference it stirs up to 6 L of water Available in either 115 or 230 V, Hz Degree of protection IP43 Optional: support and rod connector Stirs up to 6 liters of water J14

15 Overhead stirrers/mixers Overhead stirrer model 713 Versatile, with two drive shafts, one of high revolution to stir liquids with viscosity of up to 10,000 mpas (120 to 5000 r/min) and the other with high torque for liquids of up to 100,000 mpas (10 to 280 r/min.). Adjustable revolution of up to 5000 r/min. indispensable for good homogenization Microprocessed with automatic speed offset, keeping the same revolution at all times regardless of the product viscosity, with torque and temperature protections. Injected aluminum casing lined with epoxy Supplied with Ø 0.9 x 28 cm shaft with Ø 6 cm stainless steel naval propeller mod. 713D The stirring capacity depends on the product type, as a reference it stirs up to 25 L of water or 2.5 kg of cream Bivolt: V, Hz Degree of protection IP20 Optional: other types of propellers, support and rod connector (see propellers table on page J16)Stirs up to 25 liters of water Overhead stirrer model 713D Versatile, with two drive shafts, one of high revolution to stir liquids with viscosity of up to 10,000 mpas (120 to 5000 r/min) and the other with high torque for liquids of up to 100,000 mpas (10 to 280 r/min.). Adjustable revolution of up to 5000 r/min. indispensable for good homogenization Microprocessed with automatic speed offset, keeping the same revolution at all times regardless of the product viscosity, with torque and temperature protections Digital tachometer, timer to control time and display % of torque, allowing for production standardization Injected aluminum casing lined with epoxy Supplied with Ø 0.9 x 28 cm shaft with Ø 6 cm stainless steel naval propeller The stirring capacity depends on the product type, as a reference it stirs up to 25 L of water or 2.5 kg of cream Bivolt: V, Hz Degree of protection IP20 Optional: other types of propellers, support and rod connector (see propellers table on page J16) Overhead stirrer model 715 Suitable for stirring liquids with viscosity of up to 10,000 mpas. With revolution adjusted by electronic circuit with torque and temperature protection. Microprocessed with automatic speed offset, keeping the same revolution at all times regardless of the product viscosity. Injected aluminum casing lined with epoxy Supplied with Ø 0.9 x 28 cm shaft with Ø 6 cm stainless steel naval propeller Digital tachometer, timer to control time and display % of torque, allowing for production standardization The stirring capacity depends on the product type, as a reference it stirs up to 20 L of water Bivolt: V, Hz Degree of protection IP20 Optional: other types of propellers, support and rod connector (see propellers table on page J16) Stirs up to 20 liters of water mod. 715 J15

16 Overhead stirrers/mixers Overhead stirrer model 722 Suitable for stirring 60 liters of water or other products in smaller quantity (5 kg of cream). Digital tachometer allows for product standardization Ready to use (support and naval propeller included) With adjustable revolution from 120 to 2000 r/min., divided into 2 ranges (120 to 480 r/min. and 510 to 2000 r/min), suiting the work to the product type Robust: Metal casing painted with white epoxy Power: 255W Degree of protection IP23 Available in either 115 or 230 V, 50 or 60 Hz Shafts with propeller mod. 722 & 723 Overhead stirrer model 723 Suitable for stirring 150 liters of water or other products in smaller quantity (6 kg of cream). With adjustable revolution from 90 to 1600 r/min., divided into 2 ranges (90 to 430 r/min. and 400 to 1600 r/min), suiting the work to the product type Robust: Metal casing painted with white epoxy Ready to use (support and naval propeller included) Digital tachometer allows for production standardization Power: 350W Degree of protection IP23 Available in either 115 or 230V, 50 or 60 Hz Propellers Blade Centrifuge Naval Pallet Fanlight Anchor Stirring Homogenization Shearing Tritation Ballon Ballon High Viscocity Use Ø or width (cm) a 10 Compatible with stirring device P/J.C. 24/40 Lenght of the shaft for the propellers above (cm) P/J.C. 34/ , 713D, , Compatible with stirring device Lenght of the shaft for the propellers above with ECTFE (Halar) 713, 713D , Included in the standard supply of the equipment ² Use only on the low rotation axle (high torque). All the 304 stainless steel shafts are 9.3 mm in diameter and the ECTFE 10.5 mm. Table of viscosity products Degree of viscosity Very low viscosity 1 to 100 mpas Low viscosity 100 to 1000 mpas Medium viscosity 1000 to mpas High viscosity to mpas Kind of material Water medium Water, gasoline, light oils, organic solvents, shampoo etc. Hair conditioners, jelly, ketchup, paints, yogurt, fuel oil etc. Molasses, polymers, resins, tomato concentrate, cream etc. J16

17 Overhead stirrers/mixers Overhead stirrer with Planetary Support Models 713DP / 722P & 723P Prevents repetitive movements and consequent RSI problems Developed for better homogenization of large quantities of cream or other products Motorized support, mixing the whole product, with adjustable revolution from 10 to 50 r/min. Model 713DP Degree of protection IP23 Bivolt: V, Hz Models 722P & 723P Degree of protection IP23 Available in either 115 or 230 V, 50 or 60 Hz Watch the video showing how to use the Stirring devices with the Planetary Support on Compound of: 713DP Stirs up to 5 kg of cream mod. 713DP Stirring Device 713D Rod Connector 474 PTFE Scrapper Scrapper Support Anchor Propeller Naval Propeller Ø 6 cm Stainless Steel Vessel 7.5 L Planetary Support P Stirs up to 10 kg of cream Stirring Device 722 Rod Connector 474 PTFE Scrapper Scrapper Support Anchor Propeller Naval Propeller Ø 12 cm Stainless Steel Vessel 16 L Planetary Support P Stirs up to 12 kg of cream Stirring Device 723 Rod Connector 474 PTFE Scrapper Scrapper Support Anchor Propeller Naval Propeller Ø 12 cm Stainless Steel Vessel 16 L Suporte Planetário mod. 722P & 723P J17

18 Accessories PTFE Beakers PTFE beakers are resistant to most chemical reagents, very low friction coefficient (no adherence). Easy to clean, unbreakable, autoclavable, and may be sterilized by any means. Supports temperatures ranging from 270ºC to +260ºC Opaque white Lab Lifts For vertical positioning of equipment. Sturdy construction: base and platform are made of stainlesssteel and the arms are of brass Rotate and draw system for removal of seal from reactor Capacity Height x Diameter * 50 ml 60 x 42 mm 100 ml 77 x 54 mm 150 ml 86 x 55 mm 250 ml 98 x 68 mm 400 ml 115 x 82 mm 600 ml 125 x 92 mm 1000 ml 148 x 108 mm * Average internal dimensions, without nozzle Mechanical seals Made of PTFE with a Ø 3/8 borehole (other passages can be ordered). Available for the conical plugs below: JC code JC code JC code JC code JC code Universal Support With an epoxy lined aluminum base and leveling apparatus. Model Platform Height (H) min. max Weight Lab Table model 455 Supports up to x 10 cm 4.5 cm 17 cm 0.9 kg 7 kg x 20 cm 6.8 cm 35 cm 3.9 kg 10 kg x 22 cm 6.8 cm 50 cm 5 kg 10 kg Ideal for planetary stirrer, liquid cooler, and baths with refrigeration. Made of reinforced steel with epoxy finishing Dimension: 47 x 49 x 50 cm 76 mm rollers with brake Model Shaft Diameter x Total Height Aluminum 1.3 x 50 cm Stainless steel 1.3 x 63 cm Stainless steel 1.9 x 70 cm Motorized support model Electrically lifts mechanical stirrer or other equipment. Houses recipient with diameter of up to 35 cm Maximum lift height of up to 200 mm Lab Table model 456 Ideal for evaporators, vacuum pumps, cooler, among others, of easy locomotion. With two built-in outlets Made of reinforced steel with epoxy finishing Dimensions: 83 x 47 x 82 cm 76 mm rollers with brake J18

19 Fixation clamps & rod connectors Three-prong clamps Made of treated injected aluminum and prongs lined with PVC. 460 opens 102 mm, and has a Ø 13 x 150 mm long stainless steel rod. Two-arm clamps For Burettes, Balloon flasks, condensers. Made of treated injected aluminum and the prongs are lined with PVC. 463 for Burettes, opens 4 to 17 mm and the stainless steel rod is Ø 6.5 and 120 mm long. 462 opens 52 mm, and has a Ø 13 x 125 mm long stainless steel rod. 465 opens 16 to 52 mm, and the stainless steel rod is Ø 13 and 125 mm long. Rotating three-prong clamps Made of treated injected, and prongs lined with PVC mounted on a rotating clamp for fixation to a support shaft up to 16 mm. 461 opens up to 102 mm. Taper clips 466 features a rotating rod connector for fixation on the rod that may be up to 16mm long, opens 16 to 52 mm. Funnel support 464 opens up to 52 mm. Stainless steel shaft and PVC lined ring Ø 50 mm ring Ø 66 mm ring Ø 100 mm ring Ø 130 mm ring. Straight tweezers, fine stainless tip mod. 472 Two-rod connectors Made of treated inject aluminum. Allow for 90º fixation of two rods. mod e 476 Stainless steel fasteners, to attach 24/40 conical plugs. 473 Stainless steel fastener to attach 35/20 spherical plugs with a blocker. 470 with Ø of up to 16 mm. 490 length 150 mm. Mini stainless steel spatulas Total length of 150 mm, PVC lined cables Shell-shaped 6 x 15 mm Shell-shaped, 6 x 15 mm, lined with Halar * Straight flat-shaped 4,5 x 40 mm Straight flat-shaped 4,5 x 40 mm lined with Halar * Shell-shaped 3 x 12 mm Shell-shaped 3,5 x 12 mm lined with Halar *. * The Halar lining is resistant to chemical products Fastening clamps 471 one side with Ø of up to 16 mm and the other side of 13 mm. 474 one side with Ø of up to 16 mm and the other side of 19 mm. 475 Brass clamp lined with epoxy, Ø 13 x 200 mm long stainless steel rod and silicone strap (withstands temperatures of up to 180 C). Developed to fasten Beakers of up to 500 ml suspended or recipients from 80 to 80 and 250 mm in Ø diameter resting on the bench, may also be used in association with the mechanical stirrer, with thepurpose of holding the vessel still. J19

20 Rotary evaporators Rotary evaporator model 801 Vacuum rotary evaporator comprised of support with lifting mechanism, vertical condensation column, double serpentine, 1200 cm 2 thermal dissipation area, continuous reloading system and vacuum breaker. Coupling joint totally of PTFE which self-adjusts to the wear and tear, allows for pressures below 4 mbar. Heating bath mod. 550, stainless steel tub Ø 25 x 12 cm high and capacity for 4 L W heating system controlled by capillary thermostat from 50 to 120ºC and precision of ± 3ºC. Fully sealed engine. Programmable microprocessed revolution control from 5 to 210 r/min., with digital interface, self-adjustable torque regardless of variations in vacuum, temperature or voltage. Supplied with an evaporation balloon JC 24/40 and a condensation balloon JE 35/20, both 1000 ml, with clips and clamps for fixation. Available in either 115 or 230 V, Hz, 80 W. For better performance, we recommend the use of the optional items below: Balloons from 100 to 2000 ml. Other types of glass (page J22). Vacuum Pumps with PTFE protection, models: 824T, 825T, 826T, 826TV, 826TP and 828T (see page J23 and J24); Liquid cooler mod. 850 (page J22); Cooling bath mod. 860 (page J10); Lab Table (page J18). Rotary evaporator model 802 Vacuum rotary evaporator comprised of support with lifting mechanism, vertical condensation column with double serpentine, 1200 cm 2 thermal dissipation area, continuous reloading system and vacuum breaker. Coupling joint totally of PTFE which self-adjusts to the wear and tear, allows for pressures below 4 mbar. Heating bath mod. 550, stainless steel tub Ø 25 x 12 cm high and capacity for 4 L W heating system controlled by capillary thermostat from 50 to 120ºC and precision of ± 3ºC. Fully sealed engine. Programmable microprocessed revolution control from 5 to 210 r/min., with digital interface, display, self-adjustable torque regardless of variations in vacuum, temperature or voltage. Supplied with an evaporation balloon JC 24/40 and a condensation balloon JE 35/20, both 1000 ml, with clips and clamps for fixation. Available in either 115 or 230 V, Hz, 80 W. For better performance, we recommend the use of the optional items below: Balloons from 100 to 2000 ml. Other types of glass (page J22). Vacuum Pumps with PTFE protection, models: 824T, 825T, 826T, 826TV, 826TP and 828T (see page J23 and J24); Liquid cooler mod. 850 (page J22); Cooling bath mod. 860 (page J10); Lab Table (page J18). J20

21 Rotary evaporators Rotary evaporator model 803 Vacuum rotary evaporator comprised of support with lifting mechanism, vertical condensation column with double serpentine, 1200 cm 2 thermal dissipation area, continuous reloading system and vacuum breaker. Coupling joint totally of PTFE which self-adjusts to the wear and tear, allows for pressures below 4 mbar. Heating bath mod. 558, stainless steel semi-spherical tub Ø 24 x 11 cm high and capacity for 3 L, 1000W power with built-in resistance (makes cleaning easier). Heating system with digital temperature control in the environment range from +5ºC to 150ºC, with Pt100, auto-tuning and alarm. Fully sealed engine. Programmable microprocessed revolution control from 5 to 210 r/min., with digital interface, display, self-adjustable torque regardless of variations in vacuum, temperature or voltage. Supplied with an evaporation balloon JC 24/40 and a condensation balloon JE 35/20, both 1000 ml, with clips and clamps for fixation. Available in either 115 or 230 V, Hz, 80 W. For better performance, we recommend the use of the optional items below: Balloons from 100 to 2000 ml. Other types of glass (page J22). Vacuum Pumps with PTFE protection, models: 824T, 825T, 826T, 826TV, 826TP and 828T (see page J23 and J24); Liquid cooler mod. 850 (page J22); Cooling bath mod. 860 (page J10); Lab Table (page J18). Inner vision of bath Rotary evaporator model 804 Vacuum rotary evaporator comprised of support with electric lifting mechanism, vertical condensation column with double serpentine, 1200 cm 2 thermal dissipation area, continuous reloading system and vacuum breaker. Coupling joint totally of PTFE which self-adjusts to the wear and tear, allows for pressures below 4 mbar. Heating bath mod. 558, stainless steel semi-spherical tub Ø 24 x 11 cm high and capacity for 3 L, 1000 W power with built-in resistance (makes cleaning easier). Heating system with digital temperature control in the environment range from +5ºC to 150ºC, with Pt100, auto-tuning and alarm. Fully sealed engine. Programmable microprocessed revolution control from 5 to 210 r/min., with digital interface, display, self-adjustable torque regardless of variations in vacuum, temperature or voltage. Supplied with an evaporation balloon JC 24/40 and a condensation balloon JE 35/20, both 1000 ml, with clips and clamps for fixation. Available in either 115 or 230 V, Hz, 80 W. For better performance, we recommend the use of the optional items below: Balloons from 100 to 2000 ml. Other types of glass (page J22). Vacuum Pumps with PTFE protection, models: 824T, 825T, 826T, 826TV, 826TP and 828T (see page J23 and J24); Liquid cooler mod. 850 (page J22); Cooling bath mod. 860 (page J10); Lab Table (page J18). Motorized lifting J21

22 Accessories For Rotary Evaporators and Vacuum Pumps Liquids Chiller model 850 Close-circuit Chiller designed for use with rotary evaporators or other equipment that may need cooling, hermetic compressor, ecologic gas, circulation pump of 240 L/hour (without load), reservoir with 9 L capacity, coolant inlet and outlet, 480 W cooling power at 10ºC, fixed temperature at 10ºC. Supplied with visual level and digital thermometer Iron plated outside with electrostatic epoxy, resistant to corrosive chemical substance and rollers to make locomotion easier For use at room temperature up to 28 C Power: 350 W, 230 V, 60 Hz Dimensions: 500 x 460 x 500 mm (h x w x d) Optional: Lab Table (see page J18) External serpentine (see page J10) Vertical condenser For normal distillation. Diagonal condenser For normal distillation or in reflux. Spider evaporation balloon Comprised of a distributor balloon and Five 50 ml balloon flasks for multiple distillations. Cooling Trap condenser To distillate substances of low boiling point, thermo sensitive products or lyophilization dry-freezing (or use the chiller mod. 850, above). Temperature controller 411 With stainless steel probe to facilitate internal temperature reading of the condenser (page J5). Vacuum Tube VAC 10 For high performance, made of chromed brass. Analogical Vacuum Gauge VAC 15 Graduated in mm.hg and pol. Hg plus a J.C. 19/34 opener. TRAP 05 A 500 ml flask used for clearing gases. REG 02 Gauge Connects condenser to the balloon with product facilitating discharge in continuous process. J22

23 Vacuum pumps MODEL T T T 826TP 826TV T Absolute vacuum in mbar Relative vacuum¹ mm/hg pol/hg Discharge in L/ min. cfm Useful engine power (w) Noise db-c Resistant to chemicals No No Yes No Yes No Yes Yes Yes No Yes 1 Measured at an altitude of 700 meters 1 mbar = 100Pa = 0,75mmHg = 0,75 Torr = 0,0147 psi Centrifuge type vacuum/pressure pump mod. 820 Rotor with oil-lubricated blades, 40 mbar of absolute pressure, useful pressure of 1 kgf/cm 2, for filtration among others Pressure and vacuum regulators, manometer, vacuum gauge, output and intake filters with oil lubricator, supplied with 50 ml of oil Available in either 115 or 230 V, Hz, 125 W Warning: Ascertain compatibility of the evaporated substances with iron, brass and celeron. Degree of protection IP55. mod. 820 Diaphragm vacuum pumps mod. 824 & 824T (oil-free) Mod. 824 For use in laboratories, 140 mbar of absolute pressure. Silencer Available in either 115 or 230 V, Hz, 95 W Warning: Ascertain compatibility of the evaporated substances with aluminum, brass and viton. Degree of protection IP55. Mod. 824T For use in laboratories with rotary evaporators, chemical protection in PTFE, 135 mbar of absolute pressure. Available in either 115 or 230 V, Hz, 95 W Warning: Ascertain compatibility of the evaporated substances with PTFE, ETFE and kalrez. Degree of protection IP55. mod. 824 & 824T Diaphragm vacuum pumps mod. 825 & 825T (oil-free) Mod. 825 For use in laboratories, 90 mbar of absolute pressure. Supplied with vacuum regulator, vacuum gauge and silencer Available in either 115 or 230 V, Hz, 185 W Warning: Ascertain compatibility of the evaporated substances with aluminum, brass and viton. Degree of protection IP55. Mod. 825T For use in laboratories with rotary evaporators, chemical protection in PTFE, 90 mbar of absolute pressure. Supplied with vacuum regulator and vacuum gauge Available in either 115 or 230 V, Hz, 185 W Warning: Ascertain compatibility of the evaporated substances with PTFE, ETFE and kalrez. Degree of protection IP55. mod. 825 & 825T J23

24 Vacuum pumps Diaphragm vacuum pumps mod. 826 & 826T (oil-free) Mod. 826 For use in laboratories, with 2 stages, 15 mbar of absolute pressure. Supplied with vacuum regulator, vacuum gauge and silencer Available in either 115 or 230 V, Hz, 185 W Warning: Ascertain compatibility of the evaporated substances with aluminum, brass and viton. Degree of protection IP55. mod. 826 & 826T Mod. 826T For use in laboratories with rotary evaporators, with 2 stages, chemical protection in PTFE, 15 mbar of absolute pressure. Supplied with vacuum regulator and vacuum gauge Available in either 115 or 230 V, Hz, 185 W Warning: Ascertain compatibility of the evaporated substances with PTFE, ETFE and kalrez. Degree of protection IP55. mod. 826TP Diaphragm vacuum pumps mod. 826TP (oil-free) For use in laboratories with rotary evaporators, with 2 stages, chemical protection in PTFE, 35 mbar of absolute pressure. Allows adjustment of the revolution according to vacuum reducing noise Available in 230 V, 60 Hz, 240 W Warning: Ascertain compatibility of the evaporated substances with PTFE, ETFE and kalrez. Degree of protection IP55. Diaphragm vacuum pumps mod. 826TV (oil-free) For use in laboratories with rotary evaporators, with 2 stages, chemical protection in PTFE, 35 mbar of absolute pressure, automatic revolution control, with filter. Fully automated vacuum regulator, regulating revolution according to use reducing noise and wear. Available in 230 V, 60 Hz, 240 W Warning: Ascertain compatibility of the evaporated substances with PTFE, ETFE and kalrez. Degree of protection IP55. mod. 826TV Diaphragm vacuum pumps mod. 828 & 828T (oil-free) Mod. 828 For use in laboratories, with 4 stages, 5 mbar of absolute pressure. Supplied with vacuum regulator, vacuum gauge and silencer Available in either 115 or 230 V, Hz, 370 W Warning: Ascertain compatibility of the evaporated substances with aluminum, brass and viton. Degree of protection IP55. mod. 828 & 828T Mod. 828T For use in laboratories with rotary evaporators, with 4 stages, chemical protection in PTFE, 15 mbar of absolute pressure. Supplied with vacuum regulator and vacuum gauge Available in either 115 or 230 V, Hz, 370 W Warning: Ascertain compatibility of the evaporated substances with PTFE, ETFE and kalrez. Degree of protection IP55. J24

25 Melting Point Dry Melting Point mod. 431 Operational range from 50 C to 300 C with possibility of adjusting the heating power Compact and ergonomic design takes little space and provides the user with a comfortable posture Optical System with more increase (4x) for easier reading of the melting point of 3 samples at the same time with intense led lighting (does not require any change of lamp) Quick cooling system (by ventilation), quickly makes the equipment ready for new tests Quick heating Safety timer that switches off heating and switches on ventilation 30 minutes after heating has begun Holds up to 3 capillary tubing of Ø 1.5 x 75mm Available in either 115 or 230 V, Hz Power: 50 W mod. 431 Dry Melting Point mod. 431D Operational range from 50 C to 300 C with possibility of adjusting the heating power Compact and ergonomic design takes little space and provides the user with a comfortable posture Optical System with more increase (4x) for easier reading of the melting point of 3 samples at the same time with intense led lighting (does not require any change of lamp) Digital temperature display Programmable approach alarm Records 3 points for future reading (memory) Quick cooling system (by ventilation), quickly makes the equipment ready for new tests Quick heating Safety timer that switches off heating and switches on ventilation 30 minutes after heating has begun Holds up to 3 capillary tubing of Ø 1.5 x 75 mm Available in either 115 or 230 V, Hz Power: 50 W Optional: Calibration Certificate mod. 431D Industrial dehumidifier model 870 Recommended to remove humidify from environments above 45% Relative Humidity. Holds up to 60 liters/day at 30 C RH 80% or 35 liters/day at 27 C RH 60% in environments with 550 m 3 capacity (with restrictions), digital control and display of humidity, air filter, programmable timer, robust body in PP, rollers and handle to easy locomotion and drain with pump for discharge. Power: 1080 W Work range: 5ºC to 32ºC Weight: 37 kg Dimensions: 485 x 510 x 810 mm Voltage: 230V 60 Hz Wheels and handles to make moving easier J25

26 Shakers Vortex type shaker mod. 772 For test tubes of up to Ø 2.5cm, metal casing with epoxy painting, preventing the inflow of liquids. Viton Platform. Operational temperature from 5 C to 40 C, stable and compact with antiskid PVC feet and dimensions Ø 15 x 16 cm. Activated by tube pressure on the platform, horizontal circular motion with speed of 2800 r/min. Consumption 90 W Degree of protection IP42 Available in either 115 or 230 V mod. 772 Vortex type shaker mod. 774 For test tubes of up to Ø 2.5 cm, metal casing with epoxy painting, preventing the inflow of liquids. Viton Platform. Operational temperature from 5 C to 40 C, stable and compact with antiskid PVC feet and dimensions Ø 15 x 16 cm. Activated by tube pressure on the platform or continuous operation with adjustable revolution, horizontal circular motion with speed of 2800 r/min. Consumption 90 W Degree of protection IP42 Available in either 115 or 230 V mod. 774 Orbital shaker mod. 780 Metal casing with epoxy painting, ideal for synthesizing peptides. With 360º vertical circulation, adjustable revolution from 5 to 210 r/min. Digital display showing the revolution, programmable timer for automatic deactivation. Supplied with 4 clamps and ml balloons with lid and support. Power 70 W Bivolt V, Hz J26

27 Water purification Water still model 534 Reinforced aluminum casing (prevents rust), protected against broken glass in case of accident, boiler and condenser made of borosilicate glass and quartz lined heating unit to prevent pyrogenesis Water entry gauge and discharge drain Produces 4 L / hour of distilled water with consumption of 54 L / hour of water due to refrigeration Protected against water shortage and overheating Minimum network pressure: 3 m water column Available in 230 V, 3500 W, Hz mod. 534 Demineralizer model 670C Comprised of support for attachment to a wall with Rotameter, water conductibility display in about 10 µs/cm and meter which may accommodate up to 3 cartridges and holding a mixed bed cartridge mod. 670 Available in 115 or 230 V, Hz Supplied with connection hoses and expansion bolts Mixed bed cartridge model 670 Eliminates all the ionized bodies (anions and cations - except silica and CO 2 ) estimated saturation between 500 to 3000L depending on the inflowing water source, not regenerating The incoming water pressure must be at least 3 m and maximum 25 m water column (2.5kg/cm²) Activated coal cartridge model 680 Eliminates 98% of organic bodies and all the chlorine, odors and colors Saturation estimated at about 400 hours of operation The incoming water pressure must be at least 3m and maximum 25 m water column (2.5kg/cm²) Germicide cartridge model 690 With ultraviolet light to eliminate microorganisms from the water Lamp radiation: nm LED lit switch Approximate life span of the U.V. lamp: 8000 h mod. 670C mod. 670 The cartridges need a support which is supplied with model 670C (3 cartridges maximum) mod. 690 mod. 680 Advantages of the Fisatom water purification equipment Result Water still of Glass and Quartz Mod. 534 Mixed Bed Resin Cartridge Mod. 670C Demineralizer Activated Coal Cartridge Mod. 680 Germicide Cartridge Mod. 690 Conductibility 5 µs / cm Above 0,1 µs / cm PH Below 7,0 (acid) 7,0 (neutral) Calcium Traces 0,0 Iron 0,0 0,0 Silica Traces Traces Chlorine 0,0 Does not remove Removes totally Chlorides Traces 0,0 Dissolved gases Traces Traces Pyrogenesis Absent Microorganisms Removes Traces found in the supply water Removes J27

28 Índice 300ºC or 500ºC, semi-spherical heating mantles, multi-unit and splash guards J2, J3 Demineralizer, Water still and Germicide Cartridge J27 Heating mantles J4 Heating Tapes J5 Hot plates and Multi-units, and Fulkontrol type Heater J6, J7 Industrial Dehumidifier J25 Magnetic Stirrer with or without heating J11, J12, J13 Mantles with stirring J3 Melting Point J25 Multi-Unit Stirrer J12, J13 Orbital shaker J26 Overhead stirrer, Helices, Seals J14, J15, J16, J18 Overhead stirrer with Planetary Support J17 PTFE Beakers J18 Rod connectors and Clamps J19 Fisatom Equipamentos Científicos Ltda. R. Ministro Godoy, nº São Paulo SP Brasil CEP tel. (11) fax. (11) Visit our website: Rotary Evaporators J20, J21, J22 Stir bars J13 Support and mechanical, motorized stirring devices and tables.. J18 Temperature controller for heating mantles and heating tapes... J5 Thermostatic bath J8, J9, J10 Thermostatic Bath with refrigeration J10 To funnel heating mantles, Beakers, Kettle or with heating J4 Vacuum pumps J23, J24 Vortex type shaker J26 The technical features and colors of the products may change without any prior notice. Since 1962, Fisatom costumers have been an important part of our product design and improvement process. Now more than ever, your feedback is responsible for many new innovations. Thank you for the oportunity to serve you.