User and Service manual. GL-series Sausage Grill

Transcription

1 User and Service manual GL-series Sausage Grill

2 Version 2.0 APRIL Table of content 1. Table of content Introduction In General Manufacturer Name of the grill Machine tag Outline and utilization General description The grills purpose and intended use Technincal specifikations and consumption Overall dimensions Electricity Operation Installation and connection Installation Connection Maintenance and repair Cleaning Repair Spare parts Termination Destruction Appendix Signs, symbols and pictograms EU Declaration of conformity Wiring diagram 2 zones Wiring diagram 3 zones... 12

3 2. Introduction Original instruction manual This manual is a translation of the original instruction manual from FKI Fast Food Teknik of the Sausage Grill GL-series, - in the following mentioned as the grill. Purpose The purpose of this manual is to ensure proper installation, use, handling and maintenance of the grill. Accessibility The instruction manual must be kept in a to the staff well known place which is easy to access for electricians and personnel who maintain the grill. Knowledge The employer (owner of the grill) is obligated to ensure that people who operates, serve and maintain the contact grill, has read the instruction manual or as minimum are familiar with the parts which are relevant to their job. Furthermore, everybody who operate, serve and maintain the grill is obligated to seek information in this manual. 3. In General 3.1. Manufacturer The grill is manufactured by Company name: Address: FKI Fast Food Teknik A/S Byghøjvej 5, Verninge 5690 Tommerup 3.2. Name of the grill The full name of the sausage grill is GL xxxx Machine tag The machine tag is placed on the rear. 4. Outline and utilization

4 4.1. General description The grill is overall made in stainless steel with rounded edges, for easy cleaning. The contains a cabinet with fully welded steel frying pan, 2 or 3 heat zones with thermostatic control ( C) and can be with fat drawer for collecting residual frying fat. Models for build-in (GL 5945/7945) are reduced in temperature to 150 C by a blocking on the control button The grills purpose and intended use The grill is designed for cooking and warm holding of sausages of any size Technical specifications and consumption Overall dimensions Model Width x depth x hight Weight [kg] GL 9520V 460 x 375 x 120 mm 15 GL 9530V 460 x 475 x 120 mm 17 GL x 525 x 140 mm 18 GL x 525 x 140 mm 25 GL x 525 x 140 mm 30 GL x 460 x 140 mm 13,5 GL x 600 x 140 mm 17,5 GL x 265 x 135 mm 8,6 GL x 360 x 180 mm 14,3 GL x 600 x 150 mm 23,5 GL x 600 x 140 mm 22 GL x 670 x 170 mm 32 GL x 400 x 140 mm 22 GL x 600 x 140 mm 26 GL x 360 x 140 mm 23,8 GL x 600 x 140 mm 31 GL x 360 x 140 mm 19,5 GL x 460 x 140 mm 23,8 GL x 460 x 140 mm 27,5 GL x 505 x 100 mm 26,5 GL x 505 x 100 mm 33 GL x 400 x 130 mm 35 GL x 600 x 155 mm Electricity

5 Connection voltage: 240V AC Frequency: 50/60 Hz Consumed power and current Model Current [Amp.] Power [kw] GL 9520/30/40/60 8,7 2,0 GL ,7 2,7 GL 3046/3060/ ,7 2,0 /4036/4060/4660 GL6036/6040/6046/6060 8,7 2,0 GL 8036/ ,7 2,7 GL 8060/5567 8,7 2,0 GL ,7 2,0 GL ,7 2,7 GL 10060/ ,9 3,2 5. Operation The grill is divided in 2 or 3 heating zones, right/left and middle or front/back. They are controlled individually by a thermostat which is switched on by turning the knob clockwise and put it on the desired level by the mark on the front. Temperature shall be controlled after approx. 30 min. using a thermometer. If necessary adjusted up or down until desired temperature is reached. During warm up and when the heat element is active the yellow indicator lamp next to the thermostat will light up. The grill is switched off by turning the knobs to zero. 6. Installation and connection 6.1. Installation The grill is designed to be placed on a table or counter top. The grill has adjustable legs Connection The grill shall be connected to a 240V power outtake with earth connection.

6 7. Maintenance and repair 7.1. Cleaning The grill should be cleaned for residual fat several times during the day. If the grill is with fat tray just use a scraper to get residual fat to the waste hole where it will run to the collecting drawer. The drawer is emptied and cleaned as needed. Once a day the grill shall be cleaned carefully on the frying surface and all outer surfaces wiped with a damp cloth. Cleaning should not be done before the grill has cooled below 50 C 7.2. Repair Authorized service personnel with knowledge of electrical appliances should always perform Repairs.

7 Spare parts

8 Pos Part number Pcs. Description (3) Knob (3) Glow lamp Ø9 mm yellow 400V Power cord 3x1,0mm² 2,0m DK plug Power cord 3x1,0mm² 2,5m SCHUKO plug Power cord 3x1,0mm² 2,5m SIHF SCHUKO plug Heat element model GL9520V GL3060/ Heat element model GL9530V Heat element model GL Heat element model GL9560/6040/6046/4660/ Heat element model GL Heat element model GL4060/6060/ Heat element model GL35265/4036/6036/ Heat element model GL8046/7945/ Heat element model GL Heat element model GL6036/6046 og 9560 Horizontal Heat element model GL10060/10040 Horizontal (2) Connectin block 2-polet porcelain (3) Thermostat C 1-pole Cable glance PG 13, Cable glance model GL9520/ Leg, adjustable

9 8. Termination 8.1. Destruction The contact grill is marked with the above recycling symbol (EC directive 2002/96/EC) and must be disposed in accordance with your country s order. This means that when the product becomes obsolete, you should dispose it after the local municipality s rule, e.g. in unsorted waste stream 9. Appendix 9.1. Signs, symbols and pictograms The contact grill is marked with the following symbols and pictograms: Recycling symbol (see 7.1) Hot surface use gloves

10 9.2. EU Declaration of conformity Fabrikant: EF-overensstemmelseserklæring 2006/42/EF bilag II A Navn Adresse Postnr. og by FKI Fast Food Teknik A/S Byghøjvej 5, Verninge 5690 Tommerup Erklærer hermed at maskine type: - Pølseristere GL 9520/30/40/60/80 - Pølseristere GL 3060/35265/4036/4060/ Pølseristere GL 6036/6040/6046/ Pølseristere GL 8036/ Pølseristere GL 8060/ Pølseristere GL 5945/ Pølseristere GL 10040/10060 Er fremstillet i overensstemmelse med følgende EF direktiver: /42/EF Maskindirektivet under anvendelse af følgende harmoniserede standarder: - EN Elektrisk Materiel på Maskiner Søren Poulsen Direktør Verninge Underskriver Stilling Sted Dato

11 9.3. Wiring diagram 2 zones

12 9.4. Wiring diagram 3 zones Pos. Part no. Pcs. Description Power cord 3 x 1,0 mm² Connection block 2-polet porcelain (3) Thermostat C 1-pole (3) Glow lamp Ø9 mm yellow 400V 5 2(3) Heat element (Model specific see spare parts list)