HEATING & HYDRONICS TOTAL MAINTENANCE SOLUTIONS

Transcription

1 BRONZE SAFETY VALVES A.S.M.E. STANDARD, N.B. CERTIFIED BRONZE SAFETY RELIEF VALVES FOR AIR, STEAM, AND NON- HAZARDOUS GAS APPLICATIONS: Steam boilers & generators Air/gas compressors reciprocating or rotary Pressure vessels containing steam, air or non-hazardous gas. Includes tanks, receivers, sterilizers and autoclaves Pressure limits: steam to 250 PSIG 406 F air/gas to 300 PSIG 300 F Steam Air Inlet Outlet Male Female Setting /4" 1-1/2" 150 PSIG /2" 2" 150 PSIG " 2-1/2" 150 PSIG SAFETY RELIEF VALVES For hot-water heating boilers, heating systems and unfired pressure vessels, pressure cookers, steam kettles Cap. Inlet Outlet Setting lbs./hr /4"M 1"F 25 lb /4"M 1"F 30 lb /4"M 3/4"F 40 lb /4"M 3/4"F 45 lb. 575 TEMPERATURE AND PRESSURE RELIEF VALVES WATER HEATER T & P RELIEF VALVES A.S.M.E. SELF-CLOSING UP to 100,000 BTU/hr Model Size Setting Stem L 3/4" 125 lb. 2" L 3/4" 150 lb. 2" XL 3/4" 75 lb. 4" XL 3/4" 100 lb. 4" XL 3/4" 125 lb. 4" XL 3/4" 150 lb. 4" XL 3/4" 175 lb. 4" XL 3/4" 150 lb. 8" L100XL 3/4" 150 lb. 3" T & P RELIEF VALVES FOR GAS, ELECTRIC OR OIL-FIRED STORAGE WATER HEATERS Aga A.S.M.E. Therm. Temp. Steam Pres. Steam Model Inlet Outlet Length Setting Rating Btu/Hr Rating Btu/Hr L 3/4"M 3/4"F 3" 125 lb. 180, , L 3/4"M 3/4"F 3" 150 lb. 180, , /4"F 3/4"F 3" 125 lb. 180, , /4"F 3/4"F 3" 150 lb. 180, , XL 3/4"M 3/4"F 5" 125 lb. 200, , XL 3/4"M 3/4"F 5" 150 lb. 200, , XL 3/4"M 3/4"F 5" 175 lb. 200, , XL 3/4"M 3/4"F 8" 125 lb. 200, , XL 3/4"M 3/4"F 8" 150 lb. 200, , L 1"M 1"F 2" 125 lb. 450,000 1,155, L 1"M 1"F 2" 150 lb. 450,000 1,155, S 1"F 1"F 3" 125 lb. 570,000 1,670, S 1"F 1"F 3" 150 lb. 570,000 1,670, N240X 1"F 1"F 6" 125 lb. 730,000 2,195, N240X 1"F 1"F 6" 150 lb. 730,000 2,195, /2"F 1-1/2"F 3" 125 lb. 1,150,000 3,450, /2"F 1-1/2"F 3" 150 lb. 1,150,000 3,450,000 Watts 10L Watts 100XL Watts L100XL , , , , , , LOW-PRESSURE STEAM-HEATING BOILER SAFETY VALVES Cap. Inlet Setting Lbs./Hr /4"M 15 lb "M 15 lb /4"M x 3/4"F 8 lb.* /4"M x 3/4"F 12 lb.* /4"M x 3/4"F 15 lb "M x 1"F 15 lb /4"M x 1-1/2"F 15 lb. 1, /2"M x 2"F 15 lb. 1, /4"M x 3/4"F 15 lb. 400 *All valves under 15 lbs. are not A.S.M.E. approved. WATTS Model WATTS Model N240X WATTS Model 40L-40XL , , , , , , , WATTS Model 140S

2 A.S.M.E. WATER-PRESSURE SAFETY-RELIEF VALVES BRONZE BODY SAFETY-RELIEF VALVES For pressure protection only of all types of hot water heating boiler equipment. Pressure range lbs. Model Size Setting A 3/4"F 30 lb A 3/4"F 75 lb A 3/4"F 125 lb A 3/4"F 150 lb A 1"F 30 lb A 1"F 75 lb A 1"F 90 lb A 1"F 125 lb A 1"F 150 lb A 1-1/4"F 30 lb A 1-1/4"F 125 lb A 1-1/4"F 150 lb A 1-1/2"F 30 lb A 1-1/2"F 125 lb A 1-1/2"F 150 lb A 2"F 30 lb A 2"F 125 lb A 2"F 150 lb. WATER PRESSURE REDUCING VALVES Lead-free, high-performance. Maximum supply pressure of 300 PSI. Adj. Std. Mfg. Repair Kit Size Range Setting # /2" PSI 50 PSI U5B /4" PSI 50 PSI U5B /4" PSI 30 PSI U5BLP /2" PSI 50 PSI # /4" PSI 50 PSI # " PSI 50 PSI # Note: Large Capacity Valves Available Up To 8" Watts Model U5B Large capacity models Wilkins Model #70 RV WATER PRESSURE REGULATOR Reduces water pressure to a safe, consistent psi of operational pressure. Brass Plastic IRON BODY SAFETY RELIEF VALVES With expanded outlets for hot water space heating boilers. Pressure range lbs. Model Size Setting /4"x1" 30 lb /4"x1" 50 lb /4"x1" 75 lb "x1-1/4" 30lb "x1-1/4" 50 lb "x1-1/4" 75 lb /2"x2" 30 lb /2"x2" 50 lb /2"x2" 75 lb "x2-1/2" 30 lb "x2-1/2" 50 lb "x2-1/2" 75 lb. 7-2 Bronze body Watts Model 174A Iron body Watts Model , , , RESIDENTIAL INSTALLATIONS: WATTS MODEL 70A Adjusting dial for finger-tip temperature control. Standard temperature range 120 F to 160 F. Max. temperature 210 F. Max pres. 150 PSI Repair Kit Size /2" SWT /4" SWT COMMERCIAL INSTALLATIONS: WATTS MODEL LFN170 For use on large hot water supply systems. Standard temperature range 130 F to 180 F. Available for requirements below 130 F. Valves should not be used for anti-scald or anti-chill" applications. Tempering valves are not designed to compensate for system pressure fluctuations. Repair Kit Size /4" " TEMPERING VALVES Watts Model 70A Watts Model LFN

3 THERMOSTATIC MIXING VALVES ASSE 1016 listed MULTIFIXTURE THERMOSTATIC MIXING VALVES POINT OF USE Watts Regulator, Model MMV, F Size /2" /4" TEMPERATURE-LIMITING VALVES All Symmons Models FROM LEONARD VALVE Model 270-LF, 1/2 MNPT, F Model 370-LF, 3/4 MNPT, F MODEL EQUIVALENTS: SYMMONS AND LEONARD VALVE SYMMONS LEONARD VALVE Model # Inlet Outlet Model # /4 3/4 TM-26-LF / /4 LV-982-LF /4 1-1/4 LV-983-LF /4 1-1/2 LV-983-LF /2 1-1/ / LV-285-SW-LF MANUAL MIXING VALVES , WATER HAMMER ARRESTORS Watts Regulator Used to end annoying noises from banging pipes and water hammer Size /4" Can be installed at any angle /2" Hose thread adaptor only. Use with arrestor /2" Mini-arrestor /2 #15M2 Water hammer arrestor /4 #15M2 Water hammer arrestor , ZURN MANUAL MIXING VALVE This mixing valve with filter provides belowdeck water tempering. The valve is furnished complete with integral filter, two back checks, and 3/8 compressionfitting inlets and outlets SYMMONS MANUAL MIXING VALVE Tempered water supply to one faucet, mechanical mixing valve with 3/8 compression connections and in-line checks for single-tempered supply

4 WATTS BACKFLOW PREVENTERS DUAL CHECK BACKFLOW PREVENTER Watts LF7 For water supply service or individual outles. Can be installed horizontally or vertically. For low hazard applications. Size / DUAL CHECK BACKFLOW PREVENTER Watts LFH7C For in-line continuous pressure applications. Maximum pressure 150 PSI, Minimum 10 PSI / With 3/4 male & female hose fittings CONBRACO BACKFLOW PREVENTERS ATMOSPHERIC VACUUM BREAKER REPAIR KITS Conbraco Series /4, 3/8, 1/ / /4, 1-1/2, 2 Conbraco Series /4, 3/ / / Series Series BACKFLOW PREVENTER WITH ATMOSPHERIC VENT Watts LFN9 & LFN9C For exposed serviceable installations. Suitable for use under continuous pressure. Size / /8 DUAL CHECK VALVE WITH INTERMEDIATE ATMOSPHERIC VENT Watts N9-CD In-line field testable with atmospheric vent. Non-removable design. 3/4 MHT x 3/4 FHT FEBCO BACKFLOW PREVENTERS ATMOSPHERIC VACUUM BREAKER REPAIR KITS 715 (1/2-3/4 ), 710 Series (1-2 ) Size /2, 3/ / / DUAL CHECK VALVE WITH INTERMEDIATE ATMOSPHERIC VENT Watts 9D For laboratory equipment, process tanks. For hot or cold water. Can be used under continuous pressure Size Repair Kit / / ANTI-SIPHON ATMOSPHERIC VACUUM BREAKERS Watts 288 Series For cold or hot water. For high hazard cross-connection not subject to continuous pressure - 6 above flood rim. Size Repair Kit /4, Chrome /8, Chrome /2, Chrome /4, Chrome , Chrome WILKINS BACKFLOW PREVENTERS ATMOSPHERIC VACUUM BREAKER REPAIR KITS For 35XL, 35XLVCH (1/4-2 ) Size /4, 3/8 35XLVCH / / / / XL

5 RADIATOR HEATING REPAIRS RADIATOR STEAM VENTS WATER VENTS AIR VALVE #1A A float-type vent with adjustable port for true proportional venting. Port settings from (#1) slow to (#6) fast venting. 1/8" NPT angle connection. Operating pressure up to 1-1/2 PSI. Maximum pressure 10 PSI STEAM UNIT HEATER AIR VALVE #74 Float-type vent with single non-adjustable port especially designed for use with steam unit heaters. Vents air when present, with rising, dropping, or steady pressure. 1/2" FIP x 3/4" MIP shank. Operating pressure up to 35 PSI AIR VALVE #40 A float-type vent with a single non-adjustable port. For use on ordinary one-pipe system not requiring proportional venting. 1/8" NPT angle connection. Operating pressure up to 6 PSI. Maximum pressure 10 PSI SPECIAL STEAM VENTS QUICK VALVE #4 Thermostatic air vent for steam systems and process equipment. Operating on temperature changes only; does not close against water. Quick vent must be installed on a nipple 6 to 10 above horizontal return, which must be at least 18 above the boiler water line. 1/2 FIP x 3/4 MIP shank. Maximum operating pressure 25 PSI TYCO HY-VENT High-capacity float vent. For use on large air separation equipment. Capacity (PSIG) / /4 150 WATER MAIN VENT VALVE #78 Designed for use on high-pressure hot or cold water mains and process applications. Cast-brass body. Safety drain connection for discharging moisture entrained in the vented air. Tapped at the top for 1/8" NPT. Built-In check valve. 3/4" MPT shank. Maximum operating pressure of 150 PSI. Will withstand hydrostatic pressure of 450 PSI WATER VALVE #790 Especially designed for removing air from convectors, baseboard and wall radiators. Safety drain connects at the top for discharging moisture entrained in vented air. Fitting & ferrule for 3/16" OD tubing. Telescopic siphon tube. 1/8" NPT shank. Maximum operating pressure 30 PSI WATER VENT #77 Designed for efficient releasing of air in hydronic heating systems, such as baseboard radiators, convector radiators and small heating units. 1/8" MIP shank. Maximum pressure up to 50 PSI, Max temp. 240 F WATER MAIN VENT VALVE #79 Designed for use in hot or cold water mains and process applications. Tapped at top for 1/8" NPT. Safety drain connection for discharging moisture entrained in the vented air. Built-in check valve. 1/2" FIP x 3/4" MIP shank. Maximum operating pressure of 75 PSI. Will withstand hydro static pressure of 200 PSI WATER VALVE #791 Designed for convectors and small mains. Safety drain connection at top for discharging moisture entrained in the vented air. Fitting and ferrule for 3/16" OD tubing. Telescopic siphon tube. 1/4" NPT shank. Maximum operating pressure 50 PSI. AIR ELIMINATORS For hot-water heating & chilled-water cooling systems float operated AUTO-VENT #7 Vertical mounting, 1/8 FIP connection, 75 lbs. pressure. 4-3/8 x 2-1/ AUTO-VENT #71 Vertical mounting, 1/4 MIP connnection, 150 lbs. pressure. 4-3/8 x 2-1/ AUTO-VENT #27, horizontal mounting, 1/8 FIP connection. 50 lbs. pressure. 3 x 2-1/ #37, same as above with 1/8 MIP connection AUTO-VENT #78 Vertical mounting, 1/8 MIP connection, 75 lbs. pressure. 4-3/8 x 2-1/ AUTO-VENT #67, vertical mounting, 1/8 MIP connection. Up to 35 lbs. pressure. 3-3/4 x 1-9/ #68, same as above with 1/4 MIP connection

6 STEAM AND WATER-SUPPLY VALVES RADIATOR VALVE HANDLES 4-in-1 handles with adjustable plate which fits four different standard-size stem broaches which are included. Handles are available in screw or nut style. Handle Type O.D. Fits Size Screw 2-1/4" 1/4", 9/32", 5/16", 11/32" Nut 2-1/4" 1/4", 9/32", 5/16", 11/32" Screw 2-3/4" 11/32", 3/8", 13/32", 7/16" Nut 2-3/4" 11/32", 3/8", 13/32", 7/16" SUMP PUMP CHECK VALVE Bottom view Bottom view /4 SLIP X 1-1/2 SLIP SEWAGE EJECTOR AND SUMP PUMP CHECK VALVE Couplings are sized for IPS ID hose. Combination unit for 1-1/2 and 1-1/4 IPS, 1-1/2 copper Bottom view LITTLE GIANT CHECK VALVE CV-SE2 for sewage pump, 2 IPS pipe STEAM AND WATER-SUPPLY VALVES STEAM & WATER-SUPPLY VALVES For one- or two-pipe steam or water systems. Features non-rising handle and spring-packed construction. Cast-brass construction. Steam from 25" Hg. Vacuum to 150 PSIG, water up to 150 PSIG. Available in angle or straightway patterns. Model 185C. Size Type /2" Angle /4" Angle /2" Straight /4" Straight STEAM & WATER PACKLESS SUPPLY VALVES For vacuum, steam and water systems. Cast-brass construction. Non-rising handle and packless construction (diaphragm type). Steam pressures from 25 Hg. Vacuum to 125 PSIG. Water pressure up to 125 PSIG. Model 184. Size Type /2 Angle /4 Angle /2 Straightway /4 Straightway STEAM & WATER-SUPPLY VALVES For use on one- & two-pipe steam or water systems. Cast-brass construction. High lift of valve disc for free water drainage. Steam pressure up to 125 PSIG, water up to 150 PSIG. Size Type /2" Angle /4" Angle 7-6

7 STEAM TRAPS COMPLETE STEAM TRAPS FROM BARNES & JONES TMS # MFG Model Pattern NPT A B B&J Cage Size in. Unit # Barnes and Jones 122A Angle 1/ / Barnes and Jones 134A Angle 3/4 3-3/8 1-3/ STEAM TRAP REPAIR TOOLS TMS # Cover wrench /2 Spud wrench /4 Spud wrench Self-adjusting ratcheting wrench Comparison Diagram Model 122A and 134A Model 2ATL-XP and 3ATL BARNES & JONES CAGE UNIT" TRAP REPAIRS Renew any steam trap in your system even if the original trap is obsolete and the manufacturer is out of business. There is no need to take the trap offline. Replace just the interior for significant savings in time and labor cost. The following is a partial list of manufacturers for which Cage Units are available. Thermostatic Traps American Sterilizer ARCO ADSCO Barnes & Jones Belknap Braukman Babcock & Becker Broomell Cashin-Thermoflex Crane Valve Co. Cromwell Donnelly Dunham-Bush Fairbanks Hoffman Ideal Jenkins KELMAC Johns Mansville Marsh Traps Milwaukee Peerless Sarco Spirax Sterling Thermidaire Trane Thermostatic Trerice Twin City Yarway Float & Thermostatic Traps Barnes & Jones Dunham-Bush Hoffman Sarco Strong Trane Disc Trap Conversions Monel Bellows Erwell Spirax Sarco Yarway Disc Trap Conversions Stainless-Steel Bellows Erwell Spirax Sarco Yarway OTHER STEAM TRAP REPAIR KITS FROM BARNES AND JONES This handy book from Barnes and Jones lists steam trap other manufacturers alphabetically then by model number. The type is listed next to the Barnes and Jones Repair Kit #. There are four different types of cage units: Type A Diaphragm B Bronze bellows C Monel bellows (small) D Monel bellows (large) Covers for Thermostatic Traps are also available in brass/bronze ALSO AVAILABLE FROM TMS SOUTH: FLOAT & THERMOSTATIC TRAPS AND BUCKET TRAPS FROM BARNES AND JONES Barnes & Jones Cage Unit cutaway view To order a replacement Cage Unit please provide manufacturer, type of trap, model number and size. 7-7

8 PRESSURE GAUGES For indicating pressures on steam, air, water, oil or any medium that does not attack brass. Accuracy: 2% over middle half of scale range, 3% over remainder. 2" DIAL, 1/8" CENTER BACK MOUNT Range Pressure gauge 0-60 PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI WATER-PRESSURE TEST GAUGE Hose-connecting pressure gauge with high-pressure indicator hand used to test water pressure within a building. 3/4" H.T. connection PSI " DIAL, 1/4" BOTTOM MOUNT Range Pressure gauge 0-15 PSI Pressure gauge 0-30 PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI 2-1/2" DIAL, 1/4" BOTTOM MOUNT Range Pressure gauge 0-5 PSI Pressure gauge 0-15 PSI Pressure gauge 0-30 PSI Pressure gauge 0-60 PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI 3-1/2 DIAL, 1/4 BOTTOM MOUNT Range Pressure gauge 0-15 PSI Pressure gauge 0-30 PSI Pressure gauge 0-60 PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI 4-1/2 DIAL, 1/4 BOTTOM MOUNT Range Pressure gauge PSI Pressure gauge PSI LIQUID-FILLED PRESSURE GAUGES For installations where vibration is a problem. Use on any pressure medium that does not attack brass. 2-1/2" DIAL, 1/4" BOTTOM MOUNT Range Pressure gauge 0-30 PSI Pressure gauge 0-60 PSI Pressure gauge PSI Pressure gauge PSI Pressure gauge PSI GAS TEST GAUGES Intended use: nitrogen or air, do not use with any liquid. Do not use with gases incompatible with copper-based compounds. Range Gas test gauge 0-30 PSI Gas test gauge 0-6 PSI Gas test gauge 0-15 PSI A COMPLETE LINE OF INDUSTRIAL GAUGES AND THERMOMETERS IS AVAILABLE 7-8

9 INDUSTRIAL THERMOMETERS Industrial mercury in glass thermometers. Available in adjustable angle or rigid type with case sizes of 7", 9" and 12". Ranges up to 550 F. Specify the following when ordering: adjustable or rigid, case size, stem length and scale range. Range /2" stem, 9"case, adjustable angle F /2" stem, 9"case, adjustable angle F /2" stem, 7"case, adjustable angle F " stem, 9" case, adjustable angle C " stem, 9" case, adjustable angle F /2" stem, 9" case F GAUGE COCKS Since there is no packing gland to prevent leakage, care must be taken in the application of these cocks on service where leakage might create damage /4 female thread, T-handle /4 female thread, lever handle THERMOWELLS (SOCKETS) Sockets are availabe in 3-1/2", 6", 8" and 12" lengths. Sockets also come in brass, steel, and stainless steel (304 & 316). When ordering specify length and material /2" brass socket /2" brass socket with cap and chain " brass socket PYREX HIGH-PRESSURE GAUGE GLASS Size Length Type /8" 12" Red line /8" 16" Red line /8" 18" Red line /8" 24" Red line /8" 30" Red line /8" 36" Red line /8" 48" Red line /4" 10" Red line /4" 12" Red line /4" 14" Red line /4" 16" Red line /4" 18" Red line /4" 20" Red line /4" 24" Red line /4" 30" Red line /4" 36" Red line GAUGE GLASS GASKETS Trade Size I.D. O.D. Thick /2RGG 7/16" 11/16" 5/16" /8RGG 9/16" 13/16" 5/16" /4RGG 11/16" 15/16" 5/16" /8SGG 5/8" 1-1/8" 1/4" /4SGG 3/4" 1-1/4" 1/4" COIL SYPHONS Coil syphons are used on steam service to form a pocket of water between the gauge and steam. This prevents steam from reaching the bourdon tube of the gauge. 180, schedule 40 steel, 1/4-18 ends NEEDLE VALVE 1/4" Brass needle valve with Teflon packing POCKET THERMOMETER 1" dial with 5" stem and unbreakable polycarbonate crystal. Normal accuracy of + 2 F to 220 F scale to 550 F scale to 160 F scale GAUGE GLASS FRICTION RINGS I.D. O.D /64 21/ /16 13/16 WATER GAUGE LOCKNUTS BRASS Size / /4 SNUBBERS Bronze body & core. Pressure snubbers are installed on a gauge to prevent wear on the movement and reduce shock to the gauge. 1/4. Use with gasoline, light oils, air and gas

10 GAUGE GLASS CUTTERS For 1/4 through 3/4 O.D. gauge glass, laboratory glass & porcelain. ROUGH BRASS WATER GAUGES Pipe Glass Size Size Service Rating /2" 5/8"x 12" F F /2" 5/8"x 12" F F with ball checks /2" 5/8"x 12" F F WATER EXPANSION TANKS Series PLT potable water expansion tanks are designed to absorb the increased volume of water created by thermal expansion, and to maintain balanced pressure throughout the potable water supply system. Series PLT tanks feature a pre-pressurized steel tank with an expansion membrane that prevents contact of the water with the air in the tank. This prevents loss of air to the water and ensures a long and trouble-free life for the system. These tanks may be used with all types of directfired hot water heaters (gas, oil or electric) and hot-water storage tanks. IAPMO listed and ANSI/NSF 61 certified. Maximum pressure: 150PSI (10 bar) WATTS PLT SERIES Gallon potable water, maximum pressure 150 PSI Gallon potable water, maximum pressure 150 PSI SELF-TAPPING REPAIR PLUGS Hardened steel. Bright plated. Neoprene washer. For repair of leaks in boilers, tanks, pipes, etc. Size /4" /16" /8" TOGGLE TYPE REPAIR PLUG For 3/8 hole or larger. Compress spring & insert toggle bar. Tightening nut compresses rubber washer against outer surface for a tight seal CHANGE WATER HEATER ELEMENTS WITHOUT DRAINING THE TANK! WATER HEATER ELEMENT QUICK- CHANGE TOOL Turn off water at the water heater to create a vacuum. Securely attach Water Heater Element Quick Change and place bucket handle in grooves of tool to catch excess water while replacing your water heater elements

11 WATER HEATER REPAIRS RESIDENTIAL ELEMENTS RESIDENTIAL THERMOSTATS ELECTRIC THERM-O-DISC STYLE APCOM RAISED FLANGE ELEMENTS Min. Tank Watts Volts Dia. Type / /208 8" Single loop " Single loop / /208 10" Double loop 2-POINT W/ HIGH LIMIT T-4000HL, plastic/metal HLC FOR 4000/4100 THERMOSTAT T-HLC4400, plastic/ metal POINT THERMOSTAT WH-9, plastic/metal SCREW PLUG ELEMENTS Min. Tank Watts Volts Dia. Type " Single loop " Single loop " Single loop / /208 8" Single loop / /208 12" Single loop / / Double loop Low watt / / Double loop Mid watt / /208 12" Single loop / / Double loop / /208 12" Single loop " Double loop 2-POINT THERMOSTAT T-4000, plastic/metal POINT THERMOSTAT W/O HIGH LIMIT T-4100PB, plastic/metal, less reset POINT UPPER THERMOSTAT W/ HIGH LIMIT T-4100HL, for most water heaters. Plastic/ metal WATER HEATER REPAIR KITS 3-POINT THERMOSTAT WITH HIGH LIMIT WH10-4, plastic/metal for 2-element heater SINGLE ELEMENT THERMOSTAT WH9-4, plastic/metal OPEN COIL ELEMENT 1500 Watts, 120 Volts WATER HEATER REPAIR KIT Includes (2) 4500/3500 watts, 240 volts single loop screw plug elements, (1) 2-point upper thermostat and (1) HLF for 4000/4100 lower thermostat WATER HEATER REPAIR KIT Includes (2) 4500/3500 watts, 240 volts single loop screw plug elements, (1) 2-point upper thermostat and (1) 3-point lower thermostat with high limit temp

12 WATER HEATER REPAIRS COMMERCIAL THERMOSTATS HOW TO WIRE YOUR DOUBLE- ELEMENT THERMOSTAT Note: Wire color may vary on some water heaters, but connections remain the same. APCOM STYLE Wiring diagram of thermostats to standard water heater elements LOWER 180 THERMOSTAT F UPPER 180 THERMOSTAT With high limit F NEED HELP WITH YOUR DOUBLE-ELEMENT THERMOSTAT? DOUBLE-ELEMENT WATER HEATERS The majority of residential water heaters are designed with two elements controlled by two different thermostats. The upper thermostat is the brain of the water heater. It controls the heat generated by the upper and lower element. Most, if not all, residential water heaters are designed to have the upper and lower thermostats work separately. The lower element provides the main heat supply. The upper and the lower thermostats never operate simultaneously. The upper thermostat has a safety device attached to it called a High Limit Control (HLC). It has a heat sensor that will shut down the power to the heater if the temperature of the tank exceeds safety limits. The button may be reset to restore power to the heater. Do not reset the HLC until the problem causing the unit to trip is corrected. APCOM STYLE, UPPER THERMOSTAT (With high limit) THERM-O-DISC STYLE, UPPER THERMOSTAT (With high limit) THERM-O-DISC STYLE Wiring diagram of thermostats to standard water heater elements LOWER THERMOSTAT 7-12

13 WATER HEATER REPAIRS WIRING YOUR SINGLE-ELEMENT THERMOSTAT SINGLE-ELEMENT THERMOSTAT WIRING (WITH HIGH LIMIT) Most of the smaller water heaters and point-of-use heaters are designed with only one element and thus only one thermostat. Most of the single-element water heaters are wired for 120V. Never connect or adapt a 120V water heater to a 240V system. Because there is no upper thermostat on this type of heater, the high limit control is attached to the lower thermostat. (See diagrams for proper wiring.) NOTE: Because the HLC is attached to the singleelement thermostat, it looks similar to an upper thermostat for a two-element heater. Care should be taken in choosing the correct replacement thermostat. An upper thermostat will not work on a singleelement heater. RESIDENTIAL GAS NATURAL GAS VALVE 42,000 BTU. Temperature range F, shank length THERMO-DISC STYLE For single-element heater APCOM STYLE For single-element heater UNIVERSAL THERMOCOUPLE KITS DIELECTRIC UNIONS FEMALE X SWEAT /2 Sweat x 1/2 IP /4 Sweat x 3/4 IP Sweat x 1 IP /4 Sweat x 1-1/4 IP /2 Sweat x 1-1-/2 IP Sweat x 2 IP NECK/INSERT WASHERS / / / / DIELECTRIC UNION WASHERS GASKETS / / / / FEMALE X BPT /2 x 1/ /4 x 3/ x x 2 Gasket Female x Sweat Female x BPT (British Pipe Thread) Insert 7-13

14 WATER HEATER REPAIRS WATER HEATER CONNECTORS DRAIN PANS BRAIDED FLEXIBLE WATER HEATER CONNECTORS Braided stainless-steel outer covering with inner core of nontoxic polymer which is suitable for water temperatures up to 230 F. Fittings are permanently attached with leakproof, 12-point crimps Part# x 3/4" FIP x 3/4" FIP x 3/4" FIP x 3/4" FIP x 3/4 SharkBite x 3/4 FIP x 3/4" FIP x 3/4" FIP CORRUGATED STAINLESS-STEEL CONNECTORS x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP CORRUGATED COPPER CONNECTORS x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP x 3/4 FIP , , , WATER HEATER DRAIN PANS Round, high-impact plastic with 1 drain fitting WATER HEATER DRAIN PANS Square, made from heavy-duty 28-gauge galvanized steel with 1 galvanized drain fitting x 20 x x 24 x x 2 WATER HEATER STAND Made from 18-gauge galvanized steel. Stand features heavy-duty cross braces designed for water heaters 52 gallons or smaller. 21 x 21 x WATER HEATER ACCESSORIES WATER HEATER CONTINUITY TESTER Test elements and thermostats while they are still in the heater. (Electric service must be turned off at the circuit box.) MAGNESIUM ANODE RODS Mfg # AR4412 3/4 x AR3612J 3/4 x AR x HEATER HELPER WATER HEATER BAG DIP TUBES Mfg # FT52 52 Flared dip tube FTD48 48 Dielectric dip tube

15 WATER HEATER REPAIRS COMMERCIAL ELECTRIC WATER HEATER PARTS MULTI-ROD COMMERCIAL ELEMENTS Volt, 18,000 watt 1 1/2 screw plug - screw-in element Volt, 9000 watt 1 1/2 screw plug - screw-in element Volt, 15,000 watt 1 1/2 screw plug - screw-in element Volt, 18,000 watt 1 1/2 screw plug - screw-in element Volt, 4000 watt 1 1/2 screw plug - screw-in element Volt, 4500 watt 1 1/2 screw plug - screw-in element Volt, 4500 watt 1 1/2 screw plug - screw-in element Volt, 5000 watt 1 1/2 screw plug - screw-in element Volt, 5000 watt 1 1/2 screw plug - screw-in element Volt, 6000 watt 1 1/2 screw plug - screw-in element Volt, 6000 watt 1 1/2 screw plug - screw-in element Volt, 6000 watt 1 1/2 screw plug - screw-in element Volt, 15,000 watt 2 1/2 flange - flat-flange element Volt, 12,000 watt 2 1/2 flange - flat-flange element Volt, 18,000 watt 2 1/2 flange - flat-flange element LIGHT-DUTY COMMERCIAL ELEMENTS Volt, 5000 watt screw-in element Volt, 5500 watt screw-in element Volt, 6000 watt screw-in element Volt, 4500 watt screw-in element Volt, 5000 watt screw-in element Volt, 5500 watt screw-in element Volt, 6000 watt screw-in element low watt Volt, 4500 watt screw-in element Volt, 6000 watt screw-in element low watt Volt, 2500 watt screw-in element low watt Volt, 4500 watt screw-in element Volt, 6000 watt screw-in element Volt, 4500 watt screw-in element, Incoloy Volt, 6000 watt screw-in element, Incoloy WATER HEATER TOOLS WIRE LEAD COMMERCIAL ELEMENTS Volt, 15,000 watt 2 1/2 flange - flat-flange element Volt, 15,000 watt 2 1/2 flange - flat-flange element Volt, 12,000 watt 2 1/2 flange - flat-flange element Volt, 15,000 watt 2 1/2 flange - flat-flange element Volt, 18,000 watt 2 1/2 flange - flat-flange element SCREW-IN ELEMENT WRENCH New design, 1-1/2 socket size, use with 1/2 ratchet HEAVY-DUTY SCREW-IN ELEMENT WRENCH Fits standard 1/2 socket drive

16 WATER HEATER REPAIRS COMMERCIAL GAS WATER HEATER PARTS A.O. SMITH COMMERCIAL HEAVY-DUTY, NATURAL GAS BCG3, BTR & SBD Series AO Smith # Pilot burner Ignition control module Thermostat (digital) Natural gas valve COMMERCIAL HIGH-EFFICIENCY SERIES 100 BTH, SUF, HCG, 199, ,000 BTU natural gas AO Smith # Blocked outlet switch Blocked inlet switch Blower prover Flame sensor Igniter COMMERCIAL HIGH-EFFICIENCY Series 970, BTF, SUF, ,000 BTU AO Smith # Blower prover switch Inlet switch Flue switch Igniter COMMERCIAL HIGH-EFFICIENCY SERIES 200 BTH, SUF, HCG AO Smith # Blocked outlet switch, Blocked inlet switch, 120, 150, 199, Blower prover switch Spark igniter assembly Flame sensor rod

17 WATER HEATER REPAIRS COMPLETE WATER HEATERS POINT-OF-USE WATER HEATERS CHRONOMITE INSTANT-FLOW SR LOW FLOW Provides reliable point-of-use hot water. There is no pressure and temperature relief valve needed (unless required by code), saving time and money on installation Amps Volts Watts GPM Model SR-15L/ V Model SR-30L/ V Model SR-20L/ V TANKLESS NATURAL GAS OR LIQUID PROPANE HOT WATER HEATERS FROM TAKAGI Electric Natural Gas PROFESSIONAL CLASSIC ELECTRIC WATER HEATER Engineered for longer life, with resistored heating elements and premium-grade anode rod Gallon, 110 volt Gallon, 110 volt Gallon, 110 volt Gallon, 110 volt Gallon, 110 volt Gallon, 110 volt PROFESSIONAL CLASSIC ATMOSPHERIC NATURAL GAS WATER HEATER Engineered for more hot water at a low operating cost Gallon Gallon S 40 Gallon short Gallon CONCENTRIC VENT INDOOR, NON-CONDENSING ULTRA-LOW NOx TK-510C (199,000 BTU) and TK-310C (190,000 BTU). Fully modulating, gas fired, tankless water heater with sealed combustion and power-vented flue. Supplies hot water to domestic hot-water systems (directly or indirectly), and can be used with water storage tanks, recirculation systems, and/or combined domestic & heating applications Model TK-510C, 199,000 BTU Model TK-310C, 190,000 BTU NATURAL GAS INDOOR CONDENSING ULTRA-LOW NOx The T-H3-DV-N and T-H3S-DV are well suited for residential/commercial applications such as small restaurants and beauty salons. Complies with Ultra-Low NOx regulations. Utilizing commercial-grade copper alloy for the heat exchanger tubing, the T-H3 is also suitable for heavier residential usages such as space heating or domestic recirculation systems. Certified up to 10,100 ft. altitude Model T-H3 DV/OS, 199,000 BTU Model T-H3 DV/OS, 180,000 BTU NATURAL GAS OUTDOOR NON-CONDENSING The compact T-K4 is a fully modulating, gas-fired, tankless water heater perfect for residential applications. With gas inputs of 190,000 BTU, the T-K4 can produce enough hot water for up to three bathrooms in warmer climates TD2 OS, 199,000 BTU T-K4-OS 190,000 BTU TAKAGI VENTING KITS /2 Concentric, sidewall termination kit Concentric, sidewall termination kit 7-17

18 COMPLETE PUMPS AND PUMP REPAIRS 100 SERIES OIL-LUBRICATED THREE-PIECE CIRCULATORS Series 100 s three-piece, oil-lubricated design provides for easy field service with bearings, shaft and seal all housed in an assembly which can be easily repaired or replaced. The Series 100 oil-lubricated motor is specifically designed for the Series 100, and its resilient mounting provides quiet, dependable service with minimum annual lubrication. UL and CSA listings are standard Model 100NFI, cast iron, 1/12HP, 115V, single phase, closed system Model 100BI, cast iron, 1/2HP, 115V, single phase, closed system Model 100AB, all bronze, 1/2HP, 115V, single phase, open system Model 100BNFI, all bronze, 1/2HP, 115V, single phase, open system CIRCULATOR PUMPS ARMSTRONG S & H IN-LINE CIRCULATORS Armstrong Series S & H In-Line Circulators are suitable for applications such as hydronics heating and cooling, domestic water systems, multi-stage zoning and general industrial service. Both models are available in a wide range of sizes to match the performance requirements of any of these applications. Armstrong Series S & H circulators are durable and trusted products that have been used by HVAC professionals for decades. Besides the existing sleeve bearing design, Armstrong now has introduced the Maintenance-free design which has permanently lubricated ball bearings which require no maintenance at all Cast iron, 1/2 HP, 115V, S-25CI All bronze, 1/2 HP, 115V, maintenance-free, S-25AB Less volute, 1/2 HP, 115V, S-25LV Less volute, gold-painted steel, 1/6 HP, 115V, maintenance-free, H-32LV COMPASS 20-20SS The Armstrong Compass is an energy-efficient, variable-speed, wet-rotor circulator. Designed to replace existing fixed-speed circulators, with popular flangeto-flange dimensions, Compass can be considered a universal replacement for all circulators in its capacity range. Can be used in residential heating and cooling and potable water-supply applications. Performance range up to 20 GPM, up to 20 ft head. Cast iron and stainless steel. Temperature: max ambient temp. 40 C, max water temperature 110 C ARMSTRONG ASTRO MODEL 225BS The Armstrong Astro 2 circulators are designed for quiet operation and zero maintenance. Lead-free bronze volute, 115v, 60hz single phase. 2 speed,.49 amps CIRCULATOR PUMPS BELL AND GOSSETT SERIES PL MAINTENANCE-FREE BOOSTER PUMPS The Series PL close coupled booster pumps are specifically designed for quiet operation in hyrdronic, radiant and geothermal heating and cooling systems. These inline, permanently lubricated pumps are available in cast iron or lead-free bronze body construction Model PL-36, cast iron, 1/6HP, 115V, 2.1 amps, 3300 RPM Model PL-36B, lead-free bronze, 1/6HP, 115V, 2.1 amps, 3300 RPM PUMP COMPARISON CHART Armstrong Model B&G Model Grundfos Model Taco Model Astro 225-BS UP15-18B7 006-B4 Compass 20-20SS S25CI Series 100NFI UP26-64F 110 S25AB Series 100AB UP26-96BF 110 E-9 PL-36 UP26-116F 013 E-9B PL-36B UP26-116BF 0013B 7-18

19 COMPLETE PUMPS AND PUMP REPAIR CIRCULATOR PUMPS GRUNDFOS COMFORT SYSTEM - HOT-WATER RECIRCULATION SYSTEM, UP15-10 RETROFIT The water circulation system that eliminates coldwater runoff at the faucet using a bypass valve and pump with a timer to control water flow DEDICATED RETURN LINE PUMPS Model UP15-29SF 1/12 HP, 115V 1 Speed stainless-steel circulator pump Model UPS15-55SFC 1/12 HP, 115V 3 Speed stainless-steel circulator pump Model UPS26-99SFC 1/6 HP, 115V, 3-Speed stainless-steel circulator pump CIRCULATOR PUMPS TACO 007 CIRCULATOR Designed to circulate heated or chilled water in residential and light commercial hydronic systems. Also designed to circulate most common solar fluids in closed loop solar systems Model 007F5, cast iron, single phase, 1/25 HP, 115V,.74 amps, 3250 RPM Model 007SF5, stainless steel, single phase, 1/25 HP, 115V,.76 amps, 3250 RPM MODEL 009 CARTRIDGE CIRCULATOR The High Velocity series Taco 009 cartridge circulator is designed for quiet, efficient operation in higherhead/lower-flow applications for hydronic heating, radiant in-floor/panel heating, solar heating, heat recovery, and domestic water recirculation systems. Its unique field-serviceable cartridge contains all moving parts. Replacing the cartridge rebuilds the circulator. With no mechanical seal, the self-lubricating, maintenance-free design provides unmatched reliability. Available in cast-iron or stainless-steel construction Model 009-F5, 1/8HP, cast iron, single phase, 115V, 1.4 amps, 3250 RPM Model 009-SF5, 1/8HP stainless steel, single phase, 115V, 1.4 amps, 3250 RPM , HOT-LINK DOMESTIC HOT-WATER RECIRCULATION SYSTEM The Taco HLS-2 Hot-Link System for domestic hotwater recirculation reduces the time it takes for hot water comfort to reach showers and faucets. The Hot- Link System can save an average family up to 12,000 gallons of water per year, and it s easy to retrofit to an existing plumbing system. Hot Link System Model HLP-2, with Smart Technology Model 003 also shown SMART PLUS CIRCULATOR SmartPlus TM patented electronics learn and record the family s hot-water usage pattern for the first 7 days and repeats that pattern for the next 7 days providing instant hot water only when needed. This process of learn, record and repeat is continuous and never stops. And it s so smart, it never needs programming Model 006, 1/40 HP Smart Plus Circulator, 3/4 NPT Model 008, 1/25 HP Smart Plus Circulator, flanged SPEED CIRCULATOR Model 0015-MSSF3-1IFC

20 COMPLETE PUMPS AND PUMP REPAIRS LIGHT DUTY PUMP, 1-MA SERIES 1/200 HP oil-filled direct drive motor. Designed for continuous duty, submersible use only. Water transfer or recirculation & water displays LIGHT DUTY PUMP, 1-A SERIES 1/200 HP oil-filled direct drive motor. 7 ft maximum lift for submersible use only. Water transfer or recirculation. For fountains, AC units & water displays LIGHT DUTY PUMP, P-AAA SERIES 1/160 HP oil-filled direct drive motor Submersible use only. Corrosion resistant nylon body. Water transfer or recirculation. For fountains, AC units & water displays LIGHT DUTY PUMPS, 2E-38N SERIES 1/40 HP oil-filled motor. For submersed or in-line use. 300 GPH flow rate at 11.8 ft head. Epoxy coated aluminum construction. Water transfer or recirculation. For fountains, AC units & water displays SEWAGE PUMPS, 9SN-CIA-RF SERIES For sewage and effluient wastewater transfer,removal. 2 discharge, 4/10 HP designed for continuous duty. Can handle solids up to 2 diameter LITTLE GIANT PUMP PRODUCTS TRANSFER PUMP, UPSP SERIES 1/2 HP Non-submersible, inline, portable utility transfer pump CI housing. 3/4 FNPT inlet and outlet connections. 11 gpm at 60 ft lift, 10 ft power cord TRANSFER PUMP, PONY PUMP SERIES 1/10 HP Self-Priming, 115V with 6 ft lift. Instant delivery or dewatering. 3/4 hose thread on inlet & outlet. A/C /10 HP Self-priming, 12V DC with 6 ft. lift. Instant delivery or dewatering. 3/4 hose thread on inlet & outlet. D/C WASTE COLLECTION & REMOVAL SYSTEMS WCR SERIES For collection of sewage, effluent, drainage or seepage water. 20 x 30 polyethylene basin with 4/10 HP sewage pump. Includes Schedule 40 PVC discharge pipe with pre-drilled air-bleed hole. Includes 2 bulkhead fitting for power cord WASTE COLLECTION & REMOVAL SYSTEMS, WRS SERIES Designed for impractical drainage areas, under sinks, laundry trays. 3.5 gallon polyethylene basin, 1/3 HP with 13 GPM at 15 ft Designed for impractical drainage areas, under sinks, laundry trays. 5 gallon polyethylene basin, 1/3 HP with 13 GPM at 15 ft SUMP PUMPS, HT-10E SERIES 1/2 HP Continuous duty pump for dewatering, water transfer, and effluent wastewater removal. Solids up to 3/4 diameter. Handles liquids up to 200 F, 15 ft lift at 60 GPM. 15 ft power cord SUMP PUMP, 5.5 SERIES 1/4 HP oil filled motor housing. Basement sump applications. 1-1/4 discharge outlet, can handle solids up to 3/8 diameter. Includes 25 ft power cord SUMP PUMPS, 6EN SERIES 1/3 HP Continuous duty pump for dewatering, water transfer and effluent wastewater removal. Solids up to 1/2 diameter. 15 ft lift at 30 GPM. Includes 10 ft power cord SUMP PUMP, 5 SERIES 1/6 HP Continuous duty pump for dewatering and water transfer. Liquids up to 120 F, includes 10 ft power cord

21 COMPLETE PUMPS AND PUMP REPAIR HIGH WATER ALARM Indoor/outdoor. Mechanical float switch with 15 ft cable LITTLE GIANT PUMP ACCESSORIES DISCHARGE KIT Sump pump discharge kit. Includes 1-1/4 x 24 ft. polyethylene hose. 1-1/2 MNPT x 1-1/4 barbed adapter and 1-1/4 MNPT x 1-1/4 barbed adapter. Includes galvanized steel clamp DIAPHRAGM SWITCH Piggyback diaphragm switch. Converts manual pumps to automatic operation for any HP through 1/2 at 115V SUMP PUMPS ZOELLER ZOELLER PUMPS FLOOR SUCKER, MODEL 42 1/6 HP Use submerged or on any flat surface to pump clean water. Model 42 is adaptable for use with standard garden hose (fitting included) or 1" NPT. Total dynamic head flow per hour, ft ft MIGHTY-MATE, MODEL 53 CAST IRON Submersible pump for dewatering (sump) or effluent (septic tank systems) Non-clogging vortex impeller passes 1/2" solids. Float operated, submersible with 9-ft. cord plug. Total dynamic head/capacity 43 5 ft. to ft. 1/3 HP 115V with 1-1/2" NPT discharge CHECK VALVES Sump pump check valve. Flexable coupling for 1-1/4 or 1-1/2 pipe Sump pump check valve. 2 IPS compression coupling FLOAT SWITCH Piggyback mechanical float switch. Converts any manual pump to automatic. For use in dewatering and sewage MODEL 57 (60 HZ ONLY): Same specs as the Model 53, plus: all cast-iron construction stainless-steel guard and handle lower and upper bearings, oil-fed, cast iron cast-iron impeller ,

22 COMPLETE PUMPS AND PUMP REPAIRS ARMSTRONG AND BELL AND GOSSETT (B&G) PUMP REPAIR UNION FITTING SET Cast iron Lead-free bronze CAST IRON FLANGE KITS Pipe Size and Part Number Cast Iron Model 3/ /4 1-1/2 Astro 20/30/50/ Astro 230/250CI/CI-R E7/E8/E9/E12/123-TE E14/E14-TE/E15/E S-25BF LEAD-FREE BRONZE FLANGES Pipe Size and Part Number Bronze Model 3/ /4 1-1/2 Astro 20B/30B/50B/70B Astro 230SS/250SS/280/ E7B/E8B/E9B/E12B/ E14B/E12B-TE/E14B-TE/ E15B/E17B S MOTORS Armstrong B&G /12 HP, 115V-CCW /6 HP, 115V-CCW /6 HP, 115V-CCW /4 HP, 115V-CCW SEALED BEARING ASSEMBLIES Armstrong B&G LF LF LF LF LF LF MOTOR MOUNTING RINGS (RESILIENT MOTORS) Armstrong B&G /12, 1/6, 1/4, 1/3 HP /6, 1/4 HP /4, 1/3 HP BEARING ASSEMBLIES WITH SEAL & IMPELLER Armstrong B&G LF LF LF SHAFT AND SLEEVE ASSEMBLY Armstrong B&G Copper SHAFT AND BEARING MODULE Armstrong # MF-041, 1/2 shaft

23 COMPLETE PUMPS AND PUMP REPAIR ARMSTRONG AND BELL AND GOSSETT (B&G) REPAIR PARTS COUPLERS Armstrong B&G /2 x 1/2 Shaft /2 x 3/4 Shaft /2 x 1/2 Shaft, 1/4 to 1/3 HP /2 x 1/2 Shaft, 1/12 to 1/6 HP /8 Keyway x 1/2 yoke /2 x 5/8 Keyway /8 Keyway x 5/8 keyway SEAL KITS Armstrong B&G SS with BUNA, 1/ SS with Viton, 1/ SS with BUNA, 3/4 (B&G only) BODY GASKETS Armstrong B&G PO PO PO NFI Bronze IMPELLERS Armstrong B&G Material LF NFI LF Bronze NFI LF NFI LF Brass Steel LF Brass Steel LF NFI Steel LF Brass Steel LF Brass Steel LF Brass SPIRALINK COUPLERS (For B&G and Armstrong boosters & in-line pumps, Taco series ) Unitized construction eliminates all friction/wear points common to OEM couplers. Spiral spring provides universal flexibility and compensates for any degree of shaft misalignment. Absorbs starting torque and reduces load on bearings and seals. Replaces Replaces Shaft B&G # Armstrong # Rotation /2" x 1/2" , CCW up to 1/3 HP , /2" x 1/2" or 1/ , CW x 5/8, 1/2 to 3/4 HP ,P /2" x 5/8" or 5/8 P77271, CW x 5/8, 3/4 & 1HP P77237, Shaft Replaces Taco Rotation /2" x 1/2" or 1/2"x 5/8" RP CCW or 5/8" x 5/8" (Woods 3J or 4J)

24 COMPLETE PUMPS AND PUMP REPAIRS ARMSTRONG AND BELL AND GOSSETT (B&G) REPAIR PARTS * WOODS COUPLERS WITH JES INSERT J Coupler 1/2"x 1/2" with JES insert J Coupler 5/8" x 5/8" with JES insert J Coupler 1/2" x 5/8" with JES insert J Coupler 1/2" x 1/2" with JES insert J Coupler 5/8" x 5/8" with JES insert J Coupler 1/2" x 5/8" with JES insert J Coupler 1/2" x 1/2" with JES insert J Coupler 5/8" x 5/8" with JES insert J Coupler 1/2" x 5/8" with JES insert * = 2 3J, 2-1/2 4J, 3-1/2 5J INSERT ONLY SPRING COUPLERS Item /2" x 3/8" Bore /2" x 1/2" Bore x 2" long /2" x 7/16" Bore x 1-3/4" long 3 FLANGE GASKETS Armstrong B&G BELL AND GOSSETT (B&G) REPAIR PARTS PL36 & PL36B REPAIR PARTS B&G LF Seal kit P15691 Body gasket LF Impeller P64910 Flange fastener package (2 gaskets, 4 nuts, 4 bolts) Flange gasket set FLANGE GASKET KITS Armstrong B&G P P P GRUNDFOS REPAIR PARTS ISOLATION FLANGE KIT FOR UPS PUMPS / / HOUR TIMER AQUASTATS range / /4

25 COMPLETE PUMPS AND PUMP REPAIR TACO REPAIR PARTS FLANGE GASKETS 2 Pack REPLACEMENT CARTRIDGE ASSEMBLY 009-F5 Series, cast iron REPLACEMENT CARTRIDGE ASSEMBLY 009-SF5 Series, bronze REPLACEMENT CARTRIDGE ASSEMBLY 007-F5 Series, cast iron REPLACEMENT CARTRIDGE ASSEMBLY 007-SF5 Series, bronze CAST-IRON FLANGE HARDWARE KIT, 3/4 Includes 2 flanges and 4 screws, SF Other sizes available STAINLESS-STEEL FLANGE HARDWARE KIT, 3/4 Includes 2 flanges and 4 screws, SF Other sizes available HOT LINK BYPASS VALVE TEMPERATURE AQUASTAT ANALOG TIMER DIGITAL TIMER SMART PLUG Upgrade any hot-water recirculation pump with a power cord to Smart operation BEARINGS FOR BB BASE-MOUNTED PUMPS Frame A Frame B Frame C Item # 1 Shaft 2 Bearing plate gasket 3 Bearing plate bolt 4 Drain plug Ball bearing Ball bearing 7 Retainer ring 8 Bearing cover plate assy. 9 Lubrication fitting BEARINGS FOR FM BASE-MOUNTED PUMPS Item (1) (2) (3) 1 Frame 2 Hex head screws 3 Bearing cover Ball bearing 5 Shaft 6 Deflector 7 Retaining ring 8 Retaining ring (1) For the following pump models FM 1206, 1207, 1208, 1506, FM 1507,1508, 2006, 2007, (2) For the following pump models FM 1210, 1510, 2008, 2010, FM 2507, 2508, 2510, 3007, 3008, 3010, (3) For the following pump models FM 2513, 3013, 4010, 4013, FM 4016, 5010, 5013, 5016, 6013,

26 COMPLETE PUMPS AND PUMP REPAIRS TACO REPAIR PARTS REPLACEMENT PARTS FOR TACO 110 THROUGH 120 SERIES Item Taco RP Pump body-cast iron 110& RP Impeller & shaft-110 & RP Seal kit RP Motor assembly 110 & RP Coupler RP Bracket assembly RP Gasket kit, Models RP Gasket kit, Model 120 Note: Pump body, Impeller & Shaft, Motor Assembly, Bracket Assembly are available for other models. Specify model number and cast iron or bronze when ordering. REPLACEMENT PARTS FOR TACO 1600 SERIES PUMPS Item Taco 1 (1) Replacement body 2 (2) Replacement bracket 3 (3) Replacement impeller assembly RP Water seal kit 5 (4) Replacement motor assembly RP Shaft sleeve 7 (5) Replacement flange set 8 Replacement coupler 1/4-2 HP RP /2 x 5/ RP /8 x 5/ RP Replacement coupler 3 HP RP Coupler insert 3J coupler RP Coupler insert 4J coupler Coupler insert 5J coupler RP Gasket kit RP Cartridge assembly (1) Please specify cast iron or bronze, and pump model number (2) Please specify cast iron or bronze, motor frame size (48 or 56) and pump model number (3) Please specify pump number (4) Please specify HP and 115/60/1, 115/230/60/1, 200/60/3 or 230/460/60/3 (5) Please specify cast iron or bronze, and pump model number READING YOUR 1600 SERIES SERIAL NUMBER 7-26