54, 63 Round Sink / Storage Unit Installation

Size: px

Start display at page:

Download "54, 63 Round Sink / Storage Unit Installation"

Godwin Hodges
5 years ago
Views:

54, 63 Round Sink / Storage Unit Installation Applies to Models: OSC054R, OSC063R Special Tools: Level 1/4 deep well socket Caulking Gun Belt Sander OSC054R-L (Shown) DA2172i OSC054R-R (54

1 54, 63 Round Sink / Storage Unit Installation Applies to Models: OSC054R, OSC063R Special Tools: Level 1/4 deep well socket Caulking Gun Belt Sander OSC054R-L (Shown) DA2172i OSC054R-R (54 RH Round Sink / Storage Unit) OSC054R-L (54 LH Round Sink / Storage Unit) OSC063R-R (63 RH Round Sink / Storage Unit) OSC063R-L (63 LH Round Sink / Storage Unit) Rev. B (1/12)

2 LEFT SINK CABINET DIMENSIONS Waste drain 2" (5.1cm) hole 1-1/2" drain pipe 16-1/4" (41.3 cm) HOT 3" (7.6 cm) COLD 13-1/4" (35.6 cm) FLOOR 3/4" (1.9cm) Hole 1/2" NPT Water Pipe Stub out 1-3/4" (4.5cm) Min. 3-3/4" (9.5cm) Max from finished wall surface. Use 1/2" male NPT fittings on end of stubs for connections to shut-off valves. Install 1/2" inlet x 3/8" OD outlet angle shut-off valves. WALL MOUNT SERVICE WALL Waste drain 2" (5.1cm) hole 1-1/2" drain pipe COLD 8.3/4" (22.2 cm) HOT 3" (7.6 cm) 3/4" (1.9cm) Hole 1/2" NPT Water Pipe Stub out 1" (2.5cm) Min. 2-1/2" (6.4cm) Max from finished floor surface. Use 1/2" male NPT fittings on end of stubs for connections to shut-off valves. Install 1/2" inlet x 3/8" OD outlet angle shut-off valves. FLOOR MOUNT SERVICE DA2227i Note All plumbing must be made by a licensed plumbing contractor and conform to local, city, and national codes pertaining to the installation. 2

3 RIGHT SINKCABINET DIMENSIONS Waste drain 2" (5.1cm) hole 1-1/2" drain pipe 16-1/4" (41.3 cm) HOT 3" (7.6 cm) COLD 13-1/4" (35.6 cm) FLOOR 3/4" (1.9cm) Hole 1/2" NPT Water Pipe Stub out 1-3/4" (4.5cm) Min. 3-3/4" (9.5cm) Max from finished wall surface. Use 1/2" male NPT fittings on end of stubs for connections to shut-off valves. Install 1/2" inlet x 3/8" OD outlet angle shut-off valves. WALL MOUNT SERVICE WALL Waste drain 2" (5.1cm) hole 1-1/2" drain pipe COLD 8.3/4" (22.2 cm) HOT 3" (7.6 cm) 3/4" (1.9cm) Hole 1/2" NPT Water Pipe Stub out 1" (2.5cm) Min. 2-1/2" (6.4cm) Max from finished floor surface. Use 1/2" male NPT fittings on end of stubs for connections to shut-off valves. Install 1/2" inlet x 3/8" OD outlet angle shut-off valves. FLOOR MOUNT SERVICE DA2228i Note All plumbing must be made by a licensed plumbing contractor and conform to local, city, and national codes pertaining to the installation. 3

4 DRAWER REMOVAL (If Required for Access) 2 Metal Frame Drawers or Writing Surface Assembly All Molded Drawers Step 1: Lift or push down release levers (one per side) and slide out drawer assembly. Step 1: Pull drawer outward until it hits stop. DA2174i Step 2: Pull sides of drawer outward while lifting to free back of drawer from hooks and remove. 4

5 SINK / STORAGE UNIT INSTALLATION Step 1: Remove bottom access panels. DESIRED POSITION OF EDGE OF UNIT LOWER CABINET RAISE CABINET Step 2: Adjust leveling screws to fully lowered position and move cabinet to desired position. Step 3: Level cabinet with leveling screws. 1 1/2" (max.) (3.8 cm) DA2175i Equipment Alert Do not adjust leveling screws more than 1 1/2 (3.8 cm) to prevent loss of stability. 5

6 SINK INSTALLATION & PLUMBING CONNECTIONS LAMINATE TOP SHOWN Step 1: Install faucet and soap dispenser using instructions included with those items. Equipment Alert When installing a sink, Midmark recommends securing cabinet to wall. Failure to comply may result in damage to plumbing connections. Step 2: Install bottom access panel, feeding any lines thru access hole, before connecting Tapmaster lines. DA2176i Step 3: Refer to the instructions with Tapmaster faucet controller for installation procedure. 6

7 DOOR HINGE ADJUSTMENT Depth Adjustment A) Turn cam screw to move panel front to back. Vertical Adjustment A) Loosen both screws. B) Move up or down. C) Retighten screws. Horizontal Adjustment A) Turn cam screw to move panel side to side. Note Doors should be adjusted for the gap specified on the illustration. DA2177i 7

8 Adjustments and Relocating Accessories Adjusting Shelf Remove shelf (not shown) and relocate shelf brackets at desired position. Relocating Pull-Out Shelf Remove six screws from shelf slides and relocate pull-out shelf in desired position. Relocating Swing-Out Tub and/or Shelf A) Loosen screw so the shelf or tub is loose. B) Move shelf forward and out to remove. Remove screw, then re-install at desired location (do not tighten). Position shelf, then tighten screw. DA2223i 8

Freestanding Treatment Console Installation

Freestanding Treatment Console Installation pplies to Models: FTC4472 FTC4452 Special Tools: Level 3/8 masonry drill bit 9/32 wood drill bit Hammer drill This Midmark casework unit must be connected to