ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

Transcription

1 Installer s Guide ALL phases of this installation must comply with NATIONAL, TATE AND LOAL ODE 18-A73D1-8 ondensing Units 4TTA3 IMORTANT This Document is customer property and is to remain with this unit. lease return to service information pack upon completion of work. These instructions do not cover all variations in systems or provide for every possible contingency to be met in connection with the installation. hould further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes, the matter should be referred to your installing dealer or local distributor. Note: The manufacturer recommends installing only approved matched indoor and outdoor systems. All of the manufacture s split systems are A..R.I. rated only with TXV/EEV indoor systems. ome of the benefits of installing approved matched indoor and outdoor split systems are maximum efficiency, optimum performance and the best overall system reliability. Table of ontents ection 1. afety... 2 ection 2. Unit Location onsiderations... 3 ection 3. Unit reparation... 5 ection 4. etting the Unit... 5 ection 5. Refrigerant Line onsiderations... 6 ection 6. Refrigerant Line Routing... 7 ection 7. Refrigerant Line Brazing... 8 ection 8. Refrigerant Line Leak heck ection 9. Evacuation ection 10. ervice Valves ection 11. Electrical - Low Voltage ection 12. Electrical - igh Voltage ection 13. tart Up ection 14. ystem harge Adjustment ection 15. heckout rocedures and Troubleshooting... 22

2 ection 1. afety! WARNING This information is intended for use by individuals possessing adequate backgrounds of electrical and mechanical experience. Any attempt to repair a central air conditioning product may result in personal injury and/or property damage. The manufacture or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use.! WARNING These units use R-410A refrigerant which operates at 50 to 70% higher pressures than R-22. Use only R-410A approved service equipment. Refrigerant cylinders are painted a Rose color to indicate the type of refrigerant and may contain a dip tube to allow for charging of liquid refrigerant into the system. All R-410A systems use a OE oil that readily absorbs moisture from the atmosphere. To limit this hygroscopic action, the system should remain sealed whenever possible. If a system has been open to the atmosphere for more than 4 hours, the compressor oil must be replaced. Never break a vacuum with air and always change the driers when opening the system for component replacement. For specific handling concerns with R-410A and OE oil reference Retrofit Bulletins -AG006-EN and A-AG011-EN or A-AG012-EN.! WARNING LIVE ELETRIAL OMONENT! During installation, testing, servicing, and troubleshooting of this product, it may be necessary to work with live electrical components. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.! AUTION If using existing refrigerant lines make certain that all joints are brazed, not soldered.! AUTION croll compressor dome temperatures may be hot. Do not touch the top of compressor; it may cause minor to severe burning.! WARNING UNIT ONTAIN R-410A REFRIGERANT! R-410A operating pressures exceed the limit of R-22. roper service equipment is required. Failure to use proper service tools may result in equipment damage or personal injury. ERVIE UE ONLY R-410A REFRIGERANT AND A- ROVED OE OMREOR OIL.! WARNING Extreme caution should be exercised when opening the Liquid Line ervice Valve. Turn counterclockwise until the valve stem just touches the rolled edge. No torque is required. Failure to follow this warning will result in abrupt release of system charge and may result in personal injury and /or property damage A73D1-8

3 ection 2. Unit Location onsiderations 2.1 Unit Dimensions and Weight Table 2.1 Unit Dimensions and Weight Models x D x W (in) Weight* (lb) 4TTA3030A3 33 x 30 x TTA3036B3 34 x 30 x TTA3042D3 29 x 34 x TTA3048D3 29 x 34 x TTA3060D3 37 x 34 x TTA3030A4 33 x 30 x TTA3036B4 34 x 30 x TTA3042D4 29 x 34 x TTA3048D4 29 x 34 x TTA3060D4 37 x 34 x * Weight values are estimated. When mounting the outdoor unit on a roof, be sure the roof will support the unit s weight. roperly selected isolation is recommended to alleviate sound or vibration transmission to the building structure. D W 2.2 Refrigerant iping Limits 1. The maximum length of refrigerant lines from outdoor to indoor unit should NOT exceed sixty (60) feet. 2. The maximum vertical change should not exceed sixty (60) feet. 3. ervice valve connection diameters are shown in Table 5.1. tandard Line et 60 Max Line Length Note: For line lengths greater than sixty (60) feet, Refer to Refrigerant iping Application Guide, -AG006-EN or Refrigerant iping oftware rogram, (or latest revision). 60 Max Vertical hange 60 Max Vertical hange 18-A73D1-8 3

4 2.3 uggested Locations for Best Reliability Ensure the top discharge area is unrestricted for at least five (5) feet above the unit. Avoid Install Near Bedrooms Three (3) feet clearance must be provided in front of the control box (access panels) and any other side requiring service. Min 5 Unrestricted Do not locate close to bedrooms as operational sounds may be objectionable. Min. 12 to hrubbery Min 3 Unrestricted Access anel osition the outdoor unit a minimum of 12 from any wall or surrounding shrubbery to ensure adequate airflow. Outdoor unit location must be far enough away from any structure to prevent excess roof runoff water from pouring directly on the unit. Min. 12 to hrubbery Min. 12 to Wall 2.4 oastal onsiderations If installed within one mile of salt water, including seacoasts and inland waterways, models without factory supplied eacoast alt hields require the addition of BAYEA001 (eacoast Kit) at installation time A73D1-8

5 ection 3. Unit reparation 3.1 repare The Unit For Installation TE 1 - heck for damage and report promptly to the carrier any damage found to the unit. TE 2 - To remove the unit from the pallet, remove tabs by cutting with a sharp tool. ection 4. etting the Unit 4.1 ad Installation When installing the unit on a support pad, such as a concrete slab, consider the following: The pad should be at least 1 larger than the unit on all sides. The pad must be separate from any structure. The pad must be level. The pad should be high enough above grade to allow for drainage. The pad location must comply with National, tate, and Local codes. 18-A73D1-8 5

6 ection 5. Refrigerant Line onsiderations 5.1 Refrigerant Line and ervice Valve onnection izes Model Vapor Line Line izes Table 5.1 Liquid Line ervice Valve onnection izes Vapor Line onnection Liquid Line onnection 4TTA3030A3 3/4 3/8 3/4 3/8 4TTA3036B3 3/4 3/8 3/4 3/8 4TTA3042D3 3/4 3/8 3/4 3/8 4TTA3048D3 7/8 3/8 7/8 3/8 4TTA3060D3 7/8 3/8 7/8 3/8 4TTA3030A4 3/4 3/8 3/4 3/8 4TTA3036B4 3/4 3/8 3/4 3/8 4TTA3042D4 3/4 3/8 3/4 3/8 4TTA3048D4 7/8 3/8 7/8 3/8 4TTA3060D4 7/8 3/8 7/8 3/8 5.2 Factory harge Trane outdoor condensing units are factory charged with the system charge required for the outdoor condensing unit, fifteen (15) feet of tested connecting line, and the smallest indoor evaporative coil match. If connecting line length exceeds fifteen (15) feet and/or a larger indoor evaporative coil is installed, then final refrigerant charge adjustment is necessary. 5.3 Required Refrigerant Line Length Determine required line length and lift. You will need this later in TE 2 of ection 14. Total Line Length = Ft. Total Vertical hange (lift) = Ft. Line Length 5.4 Refrigerant Line Insulation Important: The Vapor Line must always be insulated. DO NOT allow the Liquid Line and Vapor Line to come in direct (metal to metal) contact. Liquid Line Vapor Line Insulation 6 18-A73D1-8

7 5.5 Reuse Existing Refrigerant Lines! AUTION If using existing refrigerant lines make certain that all joints are brazed, not soldered. For retrofit applications, where the existing indoor evaporator coil and/or refrigerant lines will be used, the following precautions should be taken: Ensure that the indoor evaporator coil and refrigerant lines are the correct size. Ensure that the refrigerant lines are free of leaks, acid, and oil. Important: For more information see publication number -AG006-EN. ection 6. Refrigerant Line Routing 6.1 recautions Important: Take precautions to prevent noise within the building structure due to vibration transmission from the refrigerant lines. omply with National, tate, and Local odes when isolating line sets from joists, rafters, walls, or other structural elements. For Example: When the refrigerant lines have to be fastened to floor joists or other framing in a structure, use isolation type hangers. Isolation hangers should also be used when refrigerant lines are run in stud spaces or enclosed ceilings. Where the refrigerant lines run through a wall or sill, they should be insulated and isolated. Isolate the lines from all ductwork. Minimize the number of 90º turns. 8 Feet Maximum Joist/Rafter Isolator ide View 8 Feet Maximum ecure Vapor line from joists using isolators every 8 ft. ecure Liquid Line directly to Vapor line using tape, wire, or other appropriate method every 8 ft. Isolation From Joist/Rafter Line et 18-A73D1-8 7

8 8 Feet Maximum Wall Isolator ide View 8 Feet Maximum ecure Vapor Line using isolators every 8 ft. ecure Liquid Line directly to Vapor Line using tape, wire, or other appropriate method every 8 ft. Isolation In Wall paces Line et Wall ealant Insulation Ductwork Vapor Line Isolator Line et Isolation Through Wall DO NOT hang line sets from ductwork ection 7. Refrigerant Line Brazing 7.1 Braze The Refrigerant Lines TE 1 - Remove caps or plugs. Use a deburing tool to debur the pipe ends. lean both internal and external surfaces of the tubing using an emery cloth A73D1-8

9 TE 2 - Remove the pressure tap cap and valve cores from both service valves. TE 3 - urge the refrigerant lines and indoor coil with dry nitrogen. TE 4 - Wrap a wet rag around the valve body to avoid heat damage and continue the dry nitrogen purge. Braze the refrigerant lines to the service valves. ontinue the dry nitrogen purge. Do not remove the wet rag until all brazing is completed. Important: Remove the wet rag before stopping the dry nitrogen purge. NOTE: recautions should be taken to avoid heat damage to basepan during brazing. It is recommended to keep the flame directly off of the basepane. 18-A73D1-8 9

10 TE 5 - Replace the pressure tap valve cores after the service valves have cooled. ection 8. Refrigerant Line Leak heck 8.1 heck For Leaks TE 1 - ressurize the refrigerant lines and evaporator coil to 150 IG using dry nitrogen. 150 IG TE 2 - heck for leaks by using a soapy solution or bubbles at each brazed location. Remove nitrogren pressure and repair any leaks before continuing A73D1-8

11 ection 9. Evacuation 9.1 Evacuate the Refrigerant Lines and Indoor oil Important: Do not open the service valves until the refrigerant lines and indoor coil leak check and evacuation are complete. TE 1 - Evacuate until the micron gauge reads no higher than 350 microns, then close off the valve to the vacuum pump Microns ON OFF TE 2 - Observe the micron gauge. Evacuation is complete if the micron gauge does not rise above 500 microns in one (1) minute. Once evacuation is complete blank off the vacuum pump and micron gauge, and close the valves on the manifold gauge set. 1 MIN. ection 10. ervice Valves 10.1 Open the Gas ervice Valve Important: Leak check and evacuation must be completed before opening the service valves. NOTE: Do not vent refrigerant gases into the atmosphere A 1/4 TURN ONLY OUNTERLOKWIE FOR FULL OEN OITION TE 1 - Remove valve stem cap. VALVE TEM TE 2 - Using an adjustable wrench, turn valve stem 1/4 turn counterclockwise to the fully open position. UNIT IDE OF VALVE TE 3 - Replace the valve stem cap to prevent leaks. Tighten finger tight plus an additional 1/6 turn. REURE TA ORT GA LINE ONNETION 18-A73D1-8 11

12 10.1 Open the Liquid ervice Valve! WARNING Extreme caution should be exercised when opening the Liquid Line ervice Valve. Turn counterclockwise until the valve stem just touches the rolled edge. No torque is required. Failure to follow this warning will result in abrupt release of system charge and may result in personal injury and /or property damage. Important: Leak check and evacuation must be completed before opening the service valves. TE 1 - Remove service valve cap. TE 2 - Fully insert 3/16 hex wrench into the stem and back out counterclockwise until valve stem just touches the rolled edge (approximately five (5) turns.) TE 3 - Replace the valve cap to prevent leaks. Tighten finger tight plus an additional 1/6 turn. ap Unit ide of ervice Valve ervice ort 3/16 ex Wrench Rolled Edge to aptivate tem ex eaded Valve ystem ection 11. Electrical - Low Voltage 11.1 Low Voltage Maximum Wire Length Table 11.1 defines the maximum total length of low voltage wiring from the outdoor unit, to the indoor unit, and to the thermostat. Table VOLT WIRE IZE MAX. WIRE LENGT 18 AWG 150 Ft. 16 AWG 225 Ft. 14 AWG 300 Ft A73D1-8

13 11.2 Low Voltage ook-up Diagrams Air andler ook-up Diagram Air onditioner Neatly bundle all low voltage wires as shown. omfort ontrol R Y1 G W1 W2 B Red Green White Black Air andler R YLO Y BK G W1 W2 W3 B Notes: 1. If electric heat does not have 3rd contactor (), connect a jumper wire from W3 to W2. If electric heat does not have 2nd contactor (B), connect a jumper wire from W2 to W1. 2. Ylo and BK may not be present on unit. Variable peed Furnace ook-up Diagram Air onditioner Neatly bundle all low voltage wires as shown. Variable peed Furnace omfort ontrol Y1 R G W1 W2 Red Green White Black R BK Y YLO G W1 W2 Notes: 1. If single stage heating thermostat is used, jumper W1-W2 on furnace terminal strip. B B O 18-A73D1-8 13

14 ommunicating Indoor Unit with 24 V ontrol ook-up Diagram Air onditioner Neatly bundle all low voltage wires as shown. omfort ontrol Y1 R G W1 W2 B Red Green White Black omm. Variable peed Furnace or Air andler R BK D Y1 Y2 G W1 W2 W3 B O Notes: 1. ee User Interface setup menu for 24 VA control mode and cooling FM options. 2. W3 terminal may not be present on unit. 3. If single stage heating thermostat is used, jumper W1-W2 on furnace terminal strip. ommunicating Indoor Unit in omm. Mode ook-up Diagram Air onditioner Neatly bundle all low voltage wires as shown. ommunicating omfort ontrol (*ONT900) D R B Brown Red omm. Variable peed Furnace or Air andler D R BK Y1 Y2 G W1 W2 W3 B O Notes: 1. ee User Interface setup menu for cooling FM options. 2. W3 terminal may not be present on unit A73D1-8

15 *AM7 Air andler ook-up Diagram Air onditioner Neatly bundle all low voltage wires as shown. Air andler omfort ontrol W G Y1 O R B Y2 Field wiring White Green Red W3 W2 W1 G YI (In) O R B YO (Out) Y2 D/BK B - Y1 - Must configure to ON for A Units. R4 ontrol Board OUTDOOR on } apacity (Tons) A (ystem) 1 2(tages) 1 2(ompressor) Must configure to OFF for single-stage compressors. 1 R1 U R RNET 1 RNET 2 FM/Ton ool Off Delay R13 R14 D9 L1 } } Torque 10 R22 INDOOR on FM 2 +12V *AM4 and GAM5 Air andler ook-up Diagram Air onditioner Neatly bundle all low voltage wires as shown. Air andler omfort ontrol W3 W2 White W White W1 Green G Green G Y YI (In) Orange O O ** Red R Red R ** B B B - YO (Out) Y - 1. * For multiple stages of electric heat, jumper W1, W2, and W3 together if comfort control has only one stage of heat. 2. ** R to O jumper must be in place as shown for cooling only, non-heat pump systems for proper operation. 3. Yi and Yo connections must be made as shown for freeze protection and internally mounted condensate overflow circuits to work properly. 4. Internally mounted condensate switch is optional and must be ordered separately. 5. If 3rd party condensate overflow switches are installed, they should be wired in series between YO and Y to the outdoor unit. Field wiring 18-A73D1-8 15

16 ection 12. Electrical - igh Voltage 12.1 igh Voltage ower upply! WARNING LIVE ELETRIAL OMONENT! During installation, testing, servicing, and troubleshooting of this product, it may be necessary to work with live electrical components. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. The high voltage power supply must agree with the equipment nameplate. ower wiring must comply with national, state, and local codes. Follow instructions on unit wiring diagram located on the inside of the control box cover and in the ervice Facts document included with the unit igh Voltage Disconnect witch Install a separate disconnect switch at the outdoor unit. For high voltage connections, flexible electrical conduit is recommended whenever vibration transmission may create a noise problem within the structure igh Voltage Ground Ground the outdoor unit per national, state, and local code requirements A73D1-8

17 ection 13. tart Up 13.1 ystem tart Up TE 1 - Ensure ections 7 through 12 have been completed. TE 2 - et ystem Thermostat to OFF. OFF DONE ANEL TE 3 - Turn on disconnect(s) to apply power to the indoor and outdoor units. ON OFF TE 4 - Wait one (1) hour before starting the unit if compressor crankcase heater accessory is used and the Outdoor Ambient is below 70ºF. 60 MIN. TE 5 - et system thermostat to ON. ON DONE ANEL 18-A73D1-8 17

18 ection 14. ystem harge Adjustment 14.1 Temperature Measurements TE 1 - heck the outdoor temperatures. ubcooling (in cooling mode) is the only recommended method of charging above 55º F ambient outdoor temperature. 120º F 55º F Outdoor Temp For best results the indoor temperature should be kept between 70º F to 80º F. Note: It is important to return in the spring or summer to accurately charge the system in the cooling mode when outdoor ambient temperature is above 55º F. 80º F 70º F Indoor Temp 14.2 ubcooling harging in ooling (Above 55º F Outdoor Temp.) TE 1 - Use the refrigerant line total length and lift measurements from ection 5.3. Total Line Length = Ft. Vertical hange (Lift) = Ft. LIFT A73D1-8

19 TE 2 - Determine the final subcooling value using total Line Length and Lift measured in TE 1 and the charts below. 1 1/2 Ton UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) 2 Ton UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) REFRIGERANT LINE LIFT (FEET) Add 3 Add 2 Add 1 of ubcooling Use Design ubcool Value REFRIGERANT LINE LIFT (FEET) Add 4 Add 2 Add 1 of ubcooling Use Design ubcool Value TOTAL REFRIGERANT LINE LENGT (FEET) TOTAL REFRIGERANT LINE LENGT (FEET) 2 1/2 Ton 3 Ton UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) REFRIGERANT LINE LIFT (FEET) Add 4 Add 3 Add 2 of ubcooling Add 1 of ubcooling Use Design ubcool Value TOTAL REFRIGERANT LINE LENGT (FEET) REFRIGERANT LINE LIFT (FEET) Add 5 Add 4 Add 3 of ubcooling Add 2 Add 1 of ubcooling Use Design ubcool Value TOTAL REFRIGERANT LINE LENGT (FEET) 3 1/2 Ton 4 Ton UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) REFRIGERANT LINE LIFT (FEET) Add 6 Add 5 Add 3 of ubcooling Add 2 of ubcooling Add 1 of ubcooling Use Design ubcool Value TOTAL REFRIGERANT LINE LENGT (FEET) REFRIGERANT LINE LIFT (FEET) Add 6 Add 4 of ubcooling Add 3 of ubcooling Add 2 of ubcooling Add 1 of ubcooling Use Design ubcool Value TOTAL REFRIGERANT LINE LENGT (FEET) UBOOL ARGING ART ORRETION TABLE (FOR LINE LENGT AND RIE) REFRIGERANT LINE LIFT (FEET) 5 Ton 60 Add Add 5 of ubcooling 30 Add 4 of ubcooling Add 2 of ubcooling Add 3 of ubcooling Design Add 1 of ubcooling TOTAL REFRIGERANT LINE LENGT (FEET) Design ubcooling Value = º F (from nameplate or ervice Facts) ubcooling orrection = º F Final ubcooling Value = º F TE 3 - tabilize the system by operating for a minimum of 20 minutes. At startup, or whenever charge is removed or added, the system must be operated for a minimum of 20 minutes to stabilize before accurate measurements can be made. 20 MIN. 18-A73D1-8 19

20 TE 4 - Measure the liquid line temperature and pressure at the outdoor unit s service valve. Measured Liquid Line Temp = º F Liquid Gage ressure = I Final ubcooling Value = º F 107 F TE 5 - Use the final subcooling value, refrigerant temperature and pressure from TE 4, to determine the proper liquid gage pressure using Table Table 14.2 R-410A REFRIGERANT ARGING ART FINAL UBOOLING ( F) LIQUID TEM ( F) LIQUID GAGE REURE (I) Example: Assume a 12º F Final ubcooling value and liquid temp of 90º F. 1. Locate 12º F Final ubcooling in Table Locate the Liquid Temperarature (90º F) in the left column. 3. The Liquid Gage ressure should be approximately 327 I. (This is the shown as the intersection of the Final ubcooling column and the Liquid Temperature row From Dwg. D Rev A73D1-8

21 TE 6 - Adjust refrigerant level to attain proper gage pressure. Add refrigerant if the Liquid Gage ressure is lower than the chart value. 1. onnect gages to refrigerant bottle and unit as illustrated. 2. urge all hoses. 3. Open bottle. 4. top adding refrigerant when liquid line temperature and Liquid Gage ressure matches the charging chart Final ubcooling value. Recover refrigerant if the Liquid Gage ressure is higher than the chart value. TE 7 - tabilize the system. 1. Wait 20 minutes for the system condition to stabilize between adjustments. Note: When the Liquid Line Temperature and Gage ressure approximately match the chart, the system is properly charged. 20 MIN. 2. Remove gages. 3. Replace service port caps to prevent leaks. Tighten finger tight plus an additional 1/6 turn. TE 8 - Verify typical performance. ressure Tables for 4TTA30***3 4TX****B3 cooling with Thermal expansion Valve (Example only - see ervice Facts) Refer to ystem ressure Tables in the ervice Facts to verify typical performance. Outdoor Temperature (Degree F) Outdoor ize & oil 36B 42D 3 48D OD *** 30A 60D oil **** B D064 Liquid ressure (IG) Outdoor ize & oil 36B 42D 3 48D OD *** 30A 60D oil **** B D064 Outdoor Indoor Wet Temp. Bulb (Degree F) (Degree F) uction ressure (IG) A73D1-8 21

22 TE 9 - Record ystem Information for reference. Record system pressures and temperatures after charging is complete. Outdoor model number = Measured Outdoor Ambient = º F Measured Indoor Ambient = º F Measured uction Line Temp = º F Liquid Gage ressure = I uction Gage ressure = I Measured Liquid Line Temp = º F ection 15. heckout rocedures and Troubleshooting 15.1 Operational And heckout rocedures Final phases of this installation are the unit Operational and heckout rocedures. To obtain proper performance, all units must be operated and charge adjustments made. Important: erform a final unit inspection to be sure that factory tubing has not shifted during shipment. Adjust tubing if necessary so tubes do not rub against each other when the unit runs. Also be sure that wiring connections are tight and properly secured. EKOUT ROEDURE After installation has been completed, it is recommended that the entire system be checked against the following list: 1. Leak check refrigerant lines.... [ ] 2. roperly insulate suction lines and fittings... [ ] 3. roperly secure and isolate all refrigerant lines... [ ] 4. eal passages through masonry. If mortar is used, prevent mortar from coming into direct contact with copper tubing... [ ] 5. Verify that all electrical connections are tight... [ ] 6. Observe outdoor fan during on cycle for clearance and smooth operation... [ ] 7. Be sure that indoor coil drain line drains freely. our water into drain pan... [ ] 8. Be sure that supply registers and return grilles are open and unobstructed... [ ] 9. Be sure that a return air filter is installed... [ ] 10. Be sure that the correct airflow setting is used. (Indoor blower motor)... [ ] 11. Operate complete system in each mode to ensure safe operation... [ ] A73D1-8

23 15.2 Troubleshooting YTEM FAULT REFRIGERANT IRUIT ead ressure Too igh ead ressure Too Low uction ressure Too igh uction ressure Too Low Liquid Refrig. Floodback (TXV/EEV) Liquid Refrig. Floodback (ap. Tube) I.D. oil Frosting ompressor Runs Inadequate or No ooling/tg OMREOR IOL IG VOLTAGE WIRING OWER ULY WAT TO EK MODE TUK OMREOR LOW VOLTAGE FUE ONTATOR OIL TERMOTAT ONTROL TRANFORMER LOW VOLTAGE WIRING ONTATOR ONTAT TART RELAY TART AAITOR RUN AAITOR EXEIVE EVA. LOAD REF. OVERARGE REF. UNDERARGE INEFFIIENT OM. TXV/EEV TUK OEN O.D. AIR REIRULATION RE. O.D. AIRFLOW NONONDENABLE EK VALVE LEAKING OV OIL DEFETIVE OV LEAKING REF. IR. RETRITION RE. I.D. AIRFLOW UEREAT * ELETRIAL ompressor & O.D. Fan Won t tart ompressor Will Not tart But O.D. Fan Runs O.D. Fan Won t tart ompressor ums But Won t tart ompressor ycles on IOL I.D. Blower Won t tart DEFROT Unit Won t Initiate Defrost Defrost Terminates on Time Unit Icing Up - ooling - eating - rimary auses - econdary auses - 3 hase Only * DEFROT ONTROL DEF. DEFROT RELAY DEF. 18-A73D1-8 23

24 The manufacturer has a policy of continuous product and product data improvement and it reserves the right to change design and specifications without notice. Representative-only illustrations included in this document Trane U..,Inc. 01/ A73D1-8