USE AND MAINTENANCE MANUAL

Size: px

Start display at page:

Download "USE AND MAINTENANCE MANUAL"

Imogen Shields
5 years ago
Views:

USE AND MAINTENANCE MANUAL SUPER MINI WARNING The manufacturer has the right to modify this manual without being obliged to update the previous editions.. IDENTIFICATION PLATE DALLA CORTE S.r.l Via Broglio, 24 20158 Milano Italy N.

1 USE AND MAINTENANCE MANUAL SUPER MINI WARNING The manufacturer has the right to modify this manual without being obliged to update the previous editions.. IDENTIFICATION PLATE DALLA CORTE S.r.l Via Broglio, Milano Italy N.F. YEAR Lt., MPa MOD. SUPER-MINI VOLT. 220 Hz WATT IPX2 EQUIPMENT OF THE MACHINE 1 filterholder for 1 shot 1 filterholder for 2 shots 1 filter for 1 shot 1 filter for 2 shots 1 shower 1 brush 1 manual coffee- tamper 1 T-shaped key 1 pipe for the water connection 1 pipe for the drainage connection WARNING This product is to be used only for the aim for which it has been projected. Any different use is to be considered improper and therefore unreasonable. The producer is not responsible for damage caused to people, objects, or to the machine itself if this is used in a wrong or unreasonable way. 1

WARNING The installation must be done following the current regulation, according to the instructions of the manufacturer and of qualified personnel.

Check that the installation systems have been prepared according to the instructions contained in this manual.

2 WARNING The installation must be done following the current regulation, according to the instructions of the manufacturer and of qualified personnel. Carefully read the instructions and the warnings contained in this manual because they give important indications about the installation of the machine and its functioning. Check that the installation systems have been prepared according to the instructions contained in this manual. Check that the electric capacity of the user s system is appropriated for the highest power of the machine of the equipment indicated on the data plate of the machine. In case of replacement of the supply pipe of the machine, only use the cable adviced by the manufacturer. The electrical safety is only achieved when the machine is correctly connected to an earthing installation. The machine must exclusively be fed with cold drink- water. The maximun network pressure must be 0.6 Mpa. Moreover, the use of any electric appliance requires some basic rules: do not touch the machine with wet hands or feet. do not use the machine when barefoot. do not let non-supervised children or non-authorized people use the machine do not wash the machine with a jet of water do not leave the machine switched on and unattended before performing any washing operation or any regular maintenance, disconnect the machine from the electric network and close the water feed tap In order to grant a complete efficiency of the machine and its perfect functioning it is essential to follow the constructor s instructions In case of damage and/or bad functioning switch the machine off, do not try to perform any direct maintenance and address the problem to the Assistance Centre authorized by the manufacturer. USER S SETTING UP FOR INSTALLATION TECHNICAL DATA 1. Water tap 2. Flexible water hoses 1 A 6. Water softener (optional) 4. Drain Hose Drain siphon 6. Electrical supply cable 5 B 7. On/Off switch A. Opening on the support plan B. Space under the support plan PIC 1 2

3 Place the machine on a surface that guarantees a secure support. To get ready for set up, make sure you have an opening ( A-pic.1) on the support surface to allow connection with systems in the space below ( B-pic.1). The machine should be exclusively connected to a source of cold drinking-water. The water pressure should be between 1 and 5 bar. If this is not possibile, please contact the manufacturer. An interception tap must be installed between the water system and the water feed pipe of the machine so that the passage of water can be closed if necessary (1-pic 1). INSTALLATION WARNING The installation must be done following current regulation and according to the following instructions. A wrong installation can cause damage to animals, objects or people. The manufacturer can not be held responsible for damages caused by improper installation. After removing the packing, check that the machine is in perfect conditions, in case of doubts do not use it. The packing components must not be left within the range of children because they might be a source of danger. Place the machine on a secure support and arrange the foot so that the machine is in the correct position. Before connecting the machine to the systems make sure that the data on the plate correspond to those of the installation place. ELECTRICAL INSTALLATION The machine is supplied with a feed pipe without a plug.the connection of the machine to the electric system can be done in two different configurations : Connection to the electric system through an appropriated bipolar switch Connection of the supply pipe to the electric network through a certified plug, which must be accessible afetr the installation and when the machine is ready to be used. WATER INSTALLATION Connect the flexible pipe to the water system. Check that there are no narrowings or squashings throughout the flexible pipe. Screw the ring nuts of flexible pipes tightly. Before connecting the pipe coming from the network and/or the water softener, introduce this in a recipent and open the tap for some minutes in order to take away possibile remains of the new pipes. INSTALLATION WITH WATER SOFTENER The water softener is adviced when feeding water of the machine has a total hardness of more than 10 French degrees, because it prevents the creation of calcium within the machine itself.the water softener must be placed so that it is easily accessible for its maintenance and near the drain siphon (see the instructions of the softener). INSTALLATION WITHOUT WATER SOFTENER If the installation of a water softener is not necessary, it is essential to install a cartridge-filter immediately after the water supply tap, in order to prevent possible impurities in the water from damaging the motorpump. DRAINING INSTALLATION

4 Install the drain flexible pipe on the connection holding the rubber of the drain basin placed under the basin and put the other end of the pipe directly into the drain siphon. Check that the drain pipe has the correct sloping to allow the basin to discharge quickly. ATTENTION If you do not follow the previous instructions, the safety and the lasting of the machine may be endangered and the warranty itself decays. STARTING AND USE OF THE MACHINE Follow these instructions with the help of the scheme of the machine placed at the end of this manual Turn on the general switch (1a) of the machine on position 1 and check that the line indicator lights up. Immediately after switching on the machine, the automatic auto-level starts filling the boiler and the indicators (2) of the keyboard () start flashing. When the boiler has been charged, the coffeegroup starts heating (4) for about 7 minutes. When the indicators (2) stop flashing, the group (4) has reached the correct thermal level and can be used to make coffee. When the group has the correct thermal level, you can turn on the switch (1b) to heat the boiler. When the manometre controlling the boiler pressure reaches 1,5 bar, it is possibile to use the drawing tap for steam (5)and hot water (6). PREPARATION OF ESPRESSO COFFEE In order to always obtain a good coffee, the filter-holder (9) must be continuously connected to the coffee group (4 ) so that it is always at the correct temperature. Take away the filter-holder (9), avoiding to touch the hot metallic parts. Afterwards clean the filter within the filter-holder from the possibile remains of used coffee. Then charge the filter with new ground coffee (1 coffee dose for the one shot filter, 2 doses for the twoshots filter), press the ground coffee with the appropriated manual coffee-tamper with which the machine is equipped and clean the filter edge from possible coffee remains. Firmly connect the filter-holder to the coffee-group (4). Place the cups on the shelf 12 (whose height can be regulated according to the dimensions of the cups) and press one of the two automatic dosing buttons P1-P2. When the indicator of the pressed key goes off, coffee is ready. NOTE This machine has three buttons to make coffee, 2 ( P1 and P2) of which electronically dosed and one with continuous supply function and stop (P). The two dosed buttons must be regulated by the technician at the moment of the installation in accordance with the user, who must not try to change the programming on his own initiative. ATTENTION Do not put the hands under the coffee groups when they are functioning. Do not touch metallic parts of the coffe groups and of the filter-holders because they may cause bad burns. HOT MILK PREPARATION 4

5 Put the milk in a jug with anti-burning handle. Put the steam pipe (8) into the jug and open the steam tap (5) related to the steam pipe that you are using. When the temperature of milk is the one you want, close the steam tap. When this operation finishes, clean the steam pipe with a damp cloth in order to avoid milk crustings on the pipe itself. ATTENTION Do not open the steam tap before introducing it into the jug to avoid possible burns. INFUSIONS PREPARATION Place a jug or a cup near the hot water lance( 1) and open the water tap ( 6), when you get to the quantity you need,close the steam tap. PERIODIC MAINTENANCE BY THE USER The efficacy of the machine is guaranteed by a correct maintenance ; therefore it is important to follow these instructions to make a correct maintenance. ATTENTION The manufacturer can not be held responsible for damages to people, things or animals caused by improper maintenance. Before performing any kind of maintenance wear protection gloves resisting to high temperatures. Before performing any kind of maintenance switch off the machine using the general interruptor (1) and close the water of the system. CLEANING OF THE BODY PARTS Clean all the parts of the machine body with a non-dripping damp cloth, without using abrasive detergents. DAILY CLEANING Every night, or at the end of work, switch the machine off, take out the filter-holder from the coffeegroups and take the filter out of the filter-holder. Clean all these parts with the brush of which the machine is equipped, taking away every coffee crusting. Also clean the shower under the coffee group using the brush. Take the basin 11 and the grill 10 out of the machine and carefully clean them from possibile crustings. PERIODIC CLEANING Every 15 days at the most take down the shower and the shower-holder placed under the coffee-group and clean everything with the appropriated brush. Put these parts back to their place, in the correct position, otherwise you might cause a bad coffeeextraction or you might damage the coffee-group. 1 b P1 1 a 5

keyboard Coffee group Steam tap Hot water tap Boiler manometre Steam lance Complete

6 P2 P Fig. 2 LEGEND 1a 1b General switch Boiler switch Leds buttons keyboard Coffee group Steam tap Hot water tap Boiler manometre Steam lance Complete filter-holder Basin grill Basin Shelf for coffee-cups Hot water supply lance Back panel Upper cup-resting panel ALARMS SYSTEM USER S MANUAL LII REV. 0 6

7 This machine,as well as performing the functions we have described, also checks their proper functioning. If one of this functions is not working properly, an alarm is created and it can be recognized in the following way: Slow flashing of the led when button is pressed This alarm functions during coffee-supply if after pressing the buttons P1 or P2 the volumetric counter does not work. The supply must be stopped manually by pressing the button P. Slow flashing of all the leds This alarm functions if the boiler s automatic charging keeps inserted for more than 2 and causes the machine to be blocked.to go back to the functions, switch the machine off and on again. Fast flashing of all the leds This alarm means that the temperature probe of the coffee-group does not work. The alarm stops when the probe has been replaced. THE FOLLOWING INFORMATION ARE DESTINED TO THE AUTHORISED ASSISTENCE CENTRE ONLY COFFEE GROUP TEMPERATURE REGULATION The installed electronic central control unit has got a temperature which can be regulated between 85 C and 110 C In order to set the temperature of the coffee group, follow these instructions: In order to raise the temperature of the group, turn the regulation knob (pic. ) clockwise, in order to decrease it turn it anticlockwise (the regulation knob can turn by ¾ of the rev to reach the maximum range in the regulation between 85 and 110 ). TEMPERATURE REGULATION 85 C C Pic BOILER PRESSURE REGULATION The pressure of the boiler steam is controlled by a mechanic adjustable pressostat. In order to regulate the pressure, follow these instructions: Remove the upper panel 15, unscrewing 4 screws Detect the regulating pressostat of the boiler in the left back part and with a blade screwdriver turn the central screw clockwise to reduce the pressure and anticlockwise to increase it. Put the upper panel back into its position. HOW TO PROGRAM THE COFFEE DOSES 7

8 The coffee doses are programmed in the following way: Keep on pressing the button P of the keyboard until all the three leds light up (about 0 ) Prepare the 1- dose filterholder and press the button P1( coffee supplì starts), when You get the quantity you want,press the button P to stop (the led of the button P1 switches off) Repeat the procedure with the dose for 2 and press the button P2 (coffee supply starts), when You get the quantity you want,press the button P to stop ( only the led of the of the button P stays on) In order to record the doses and finish the procedure, press again the button P (the corresponding led switches off too). HOW TO PROGRAM THE PRE-INFUSION TIME It is possible to regulate the pre-infusion time as follows: While you keep on pressing the button P1, turn on the machine; the led of button P1 will lighten, turn off the machine and turn it on again, in this way you have set the pre-infusion time at 4 s. If You prefer a shorter time (2 s), perform the same operation but press the button P2 instead of P1, the led of button P2 will then lighten up. In order to cancel the pre-infusion time completely, follow the procedure described here above but press button P when you turn on the machine; the corresponding led will lighten up, then switch off and on again the machine BOILER RESISTANCE ELECTRIC INSTALLATION SECURITY THERMOSTAT 8

9 GROUP RESISTANCE SECURITY THERMOSTAT EV GROUP EV BOILER LEVEL PUMP PRESSOSTAT KEYBOARD GROUP TEMP. PROBE BOILER SWITCH VOLUMETRIC COUNTER TERMINAL BOARD BOILER LEVEL PROBE CENTRAL CONTROL UNIT TEMPERATURE REGULATION GENERAL SWITCH 9

MANUAL FOR USE AND MAINTENANCE LSC Rev Ed. 11/2011

ANTI STILI...UNA PASSIONE espresso coffee machines MANUAL FOR USE AND MAINTENANCE LSC 022 - Rev. 00 - Ed. 11/2011 WEEE espresso coffee machines Disposal of the equipment by the users within the European