FLO KING STAINLESS STEEL PUMPS AND FILTER ATTACHMENTS

Transcription

1 FILTER S Y S TEM S TM The Original 4-in-1 FLO KING FLO KING STAINLESS STEEL PUMPS AND FILTER ATTACHMENTS PREFERRED MATERIAL OF CONSTRUCTION FOR... Aggressive, high-temperature alkaline cleaners Post-anodize hot seal tanks (often over 200 F, 93 C) Caustic chemical strippers Bulletin 23.5 Many permanganate solutions for printed circuits (L-r) Stainless steel BX3000, BX1200, SP12K, Lab Series, and BX5000 pumps. Low-profile BXL2500 and BXL5000 (Bulletins 14.2 & 14.5) also available in stainless. Other baths that cause plastics to warp, swell, crack or otherwise fail Stainless steel units are outstanding for solution circulation where plastics won t do. With the appropriate cartridge holder, these units can also be used for filtration. All models made of 316 material. Attachments include the stainless-steel items shown below. Single Cartridge Holder. Threaded end screws onto impeller housing to accept one filter cartridge. Used primarily on 1200 model. Double Cartridge Holder. Holds two filter cartridges. Fits 1200, 2500, 3000 & 5000 stainless models. Quad Cartridge Holder. Lots of solids? Use four cartridges on 1200, 2500, 3000 or 5000 model. Slide-In Filter Cartridge Adapter (SIFCA). Allows operator to change filter cartridges without moving pump from tank. See Bulletin 19 for product details. Filter Cartridges. If conventional filters will not survive solution, pleated stainless steel cartridge can be cleaned and reused indefinitely. Adapter head mounts directly to cartridge holder. Pioneers of In-Tank Filtration Elbow & Extension. Directs and streamlines flow of solution from pump discharge port. Floductors. Nozzles for those who wish to add pipe sparging system to pump discharge port (see Bulletin 23). Strainers. Protect pump impeller from foreign objects that may be in solution.

2 FILTER S Y S TEM S TM The Original 4-in-1 FLO KING Bulletin 23.5 FLO KING STAINLESS STEEL PUMPS & FILTER ATTACHMENTS Flo King systems made of CPVC and polypropylene satisfy most applications in the metal finishing industry. However, where plastics are damaged by aggressive chemicals and/or high temperatures, stainless steel is often a viable alternative. Standard Flo King SP12K, BX5000, BX3000, and BX1200 stainless steel units are available in a single pump body length, as shown below. Low-profile BXL2500 and BXL5000 available only in 12" body length. Call for availability and pricing on custom lengths. Stainless steel Lab Series units available in the same lengths and dimensions shown on Bulletin 16. All models except Lab Series feature our 360 swiveling impeller housing to enable preferred positioning of discharge port in tank. Stainless steel parts manufactured from 316 material. 6 x 10-1/2 x 3/8" 15 x 27 x 1 cm SWIVELING IMPELLER 5-1/2" DIA (14 cm) 14-1/2" 37 cm 7-1/2" (19 cm) 14" 36 cm 1-1/2" PIPE THREAD 2 1 / 2 " - 8 THREADS (NPSM*) 19" 48 cm Stainless Steel SP12K Flow Rate: 12,000 gallons per hour (45,000 liters per hour) at 60 Hz. A reduction of 18% (±3%) is typical at 50 Hz. Pressure: 50 feet (15.25 meters) of head pressure (15 psi) Weight: 69 pounds (31 kg) Motor: Epoxy-coated, TEFC, Thermally Protected. Ready for hard wiring (does not include cord or plug). Available in: 3 phase, 3 HP (2235 watt), /460 V, 8-7.4/3.7 A, 60 Hz, 3450 RPM. 3 phase, 3 HP, 220/380/440 V, 8.2/4.7/4.2 A, 50 Hz, 2850 RPM Single phase, 3 HP, V, A, 60 Hz, 3450 RPM Operation: To ensure proper operation and for best results, solution should be 4" (10 cm) or more above Weep Hole on pump body. Solution should also be at least 2" (5 cm) below Motor Base. 4 x 7 x 1/4" 10 x 18 x 0.6 cm 12" 30.5 cm SWIVELING IMPELLER 3-7/16" DIA (8.75 cm) 2-1/2" 6.4 cm 1" PIPE THREAD 1 1 / 2 " / 2 THREADS (NPSM*) 6" 15 cm 2.5" 6.5 cm 12" 30.5 cm 15-3/4" 40 cm Stainless Steel BX5000 Flow Rate: 5,000 gallons per hour (19,000 liters per hour) at 60 Hz. A reduction of 18% (±3%) is typical at 50 Hz. Pressure: 27 feet (8.2 meters) of head pressure Weight: 38 pounds (17 kg) Motor: Epoxy-coated, TEFC, Thermally Protected. Available in: Single phase, 3/4 HP (560 watt), 120/240 V, 11/5.5 A, 50/60 Hz, 2850/ 3450 RPM 3 phase, 1 HP (760 watt), 230/ 460 V, 3.0/1.5 A, 60 Hz, 3450 RPM. Note: There is an additional charge for 3-phase motors. Operation: To ensure proper operation and for best results, solution should be 4" (10 cm) or more above Weep Hole on pump body. Solution should also be at least 2" (5 cm) below Motor Base. Threaded Double or Quad Cartridge Holder required for filtration applications. 5-3/4" (15 cm) * National Pipe, Straight Mechanical DOUBLE CARTRIDGE HOLDER * National Pipe, Straight Mechanical 4 x 7 x 1/4" 10 x 18 x 0.6 cm 12" 30.5 cm SWIVELING IMPELLER 3-7/16" DIA (8.75 cm) 2-1/2" 6.4 cm 1" PIPE THREAD 1 1 / 2 " / 2 THREADS (NPSM*) 5" 13 cm 2.5" 6.5 cm 10-1/2" 26.5 cm 15-3/4" 40 cm 5-3/4" (15 cm) DOUBLE CARTRIDGE HOLDER Stainless Steel BX3000 Flow Rate: 3,000 gallons per hour (11,000 liters per hour) at 60 Hz. A reduction of 18% (±3%) is typical at 50 Hz. Pressure: 27 feet (8.2 meters) of head pressure Weight: 30 pounds (13.5 kg) Motor: Epoxy-coated, TEFC, Thermally Protected. Available in: Single phase, 1/3 HP (250 watt), 120/240 V, 6.0/3.0 A, 50/60 Hz, 2850/ 3450 RPM Call for information on 3-phase motors for BX3000. Operation: To ensure proper operation and for best results, solution should be 3" (8 cm) or more above Weep Hole on pump body. Solution should also be at least 2" (5 cm) below Motor Base. Threaded Double or Quad Cartridge Holder required for filtration applications. 4 x 7 x 1/4" 10 x 18 x 0.6 cm 9-1/2" 24 cm SWIVELING IMPELLER 2-3/8" DIA (6 cm) 1-1/2" / 2 THREADS (NPSM*) 4" 10 cm 3/4" PIPE THREAD 2" (5 cm) 3" 7.5 cm SINGLE CARTRIDGE HOLDER 7" 18 cm 11-1/2" 29.5 cm Stainless Steel BX1200 Flow Rate: 1200 gallons per hour (4500 liters per hour) at 60 Hz. A reduction of 18% (±3%) is typical at 50 Hz. Pressure: 12 feet (3.6 meters) of head pressure Weight: 12 pounds (5.5 kg) Motor: Epoxy-coated, TEFC, Thermally Protected. Available in: Single phase, 1/12th HP (60 watt), 115 V, 2.6 A, 60 Hz, 3000 RPM Single phase, 1/12th HP, 230 V, 1.3 A, 50/60 Hz, 3000 RPM Single phase, 1/12th HP, 115 V, 2.6 A, 50/60 Hz, 3000 RPM Operation: To ensure proper operation and for best results, solution should be at least 1" above Weep Hole on pump body. Threaded Single, Double or Quad Cartridge Holder required for filtration applications. * National Pipe, Straight Mechanical * National Pipe, Straight Mechanical

3 Bulletin 15 FLO KING BRINGS YOU THE TIME-HONORED ORIGINAL BX1200 PROVIDES A FLOW RATE OF 1200 GALLONS PER HOUR (4500 LPH) USING A TOTALLY ENCLOSED, FAN-COOLED, 1/12TH-HP (60-watt) AVAILABLE IN MULTIPLE BODY LENGTHS TO CUSTOM FIT YOUR TANK USES ONLY A 4-INCH-SQUARE (10-cm-square) AREA OF TANK SPACE ACCEPTS EASY-TO-ATTACH FILTERS IN MANY SIZES INDUSTRY WORKHORSE A complete, ready-to-operate portable filter system... No Plumbing No Clamping No Alterations Simply remove from box, set on tank and start filtering. HIGH-TECH, BEARINGS, MATERIALS, AND SUPERIOR KNOW-HOW BRING THIS INDISPENSABLE SYSTEM TO INDUSTRY... IF YOU NEED A FILTER SYSTEM TOMORROW CALL US TODAY Pioneers of In-Tank Filtration H

4 THE FLO KING BX1200 The BX1200 provides a maximum flow rate of 1200 gallons (4500 liters) per hour. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (4", 6", 8", 10", 12", 14" and 16") enable use of the BX1200 in tanks with varying solution levels and depths. The BX1200 comes complete, preassembled, and ready to operate and includes the items shown in the labeled photograph below. For best results in most metal finishing solutions, use the BX1200 with our PMCA Permacore MAGNUM reusable or FK50 Poly-Spun disposable filter cartridges in the appropriate length. FLO KING BX1200 SPECIFICATION PUMP MATERIALS: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel (see Bulletin 23.5) as pump materials of construction. Standard shaft is made of Teflon-covered 303 stainless steel. Titanium and Hastelloy C276 alloy shafts available on special-order basis. Call for pricing. FLOW RATE: 1200 gallons per hour (4500 liters per hour) at 60 Hz. A flow-rate reduction of 18% (±3%) is typical when operated at 50 Hz. PRESSURE: 12 feet (3.6 meters) of head pressure WEIGHT: About 10 pounds (4.5 kg) in CPVC, depending on pump body length : Epoxy coated, 1/12th HP (60 watt), single phase, 3000 rpm, TEFC, thermally protected. When ordering, specify one of the following three motors: 115 volts, 60 Hz, 2.6 A 115 volts, 50/60 Hz, 2.0 A 230 volts, 50/60 Hz, 1.3 A RUNNING PUMP DRY DOES NOT DAMAGE, PUMP, SEALS OR BEARINGS Bulletin 15 Universal Bracket screws Handle DRIP COVER Motor Universal Bracket adjustment (2-1/2 TO 4-3/4") 6 to 12 cm 10 4" cm 7" 18 cm Universal Bracket Weep hole DISCHARGE PORT FILTER screw (Thumbscrew) Important! To ensure proper priming, solution must always be above Weep Hole on pump body. Specify length of pump body when ordering. Use Bulletin 12.1 for prompt sizing recommendations. Motor base Pump body 45 elbow Directable outlet extension Filter cartridge Install filter plug here 8" (20 cm) Motor base (3/8" x 6" x 6") 1 x 15 x 15 cm Impeller housing DIAMETER (2-7/8") 7 cm Tank top view 3/4" PIPE THREAD A Dimension (see chart below) 2" (5 cm) Universal Bracket can be installed at either of two locations on motor base to accommodate preferred location of discharge port in tank. Note: 8" dimension at left includes provision for 45 High-Flow Elbow & 3" Directable Outlet Extension on discharge port. MEASUREMENT FROM BOTTOM OF TO CENTER OF DISCHARGE PORT () PUMP MODEL BX BX BX BX BX /2" 6-1/2" 9-1/16" 10-3/4" 12-1/2" (11 cm) (17 cm) (23 cm) (28 cm) (32 cm) BX /2" (37 cm) Special Order Item BX /2" (42 cm)

5 Bulletin 14 THE FLO KING BX3000 A FLOW RATE OF 3000 GPH (11,000 LPH) USING A TOTALLY ENCLOSED, FAN-COOLED, 1/3-HP GREAT FOR TANKS OF INTER- MEDIATE SIZE OR AGGRESSIVE AGITATION AND FAST CLEANUP OF SMALLER TANKS BUILT IN SEVERAL LENGTHS FOR MOST TANK CONFIGURATIONS A CLEAN SOURCE OF AGITATION... AN ALTERNATIVE TO AIR OR MECHANICAL AGITATION USE IN ONE TANK OR AS A UTILITY UNIT IN MANY TANKS CHANGE FILTERS QUICKLY... NO TOOLS, NO DOWNTIME No plumbing, clamping or costly installation. Complete, ready to operate out of the box and into your tank. No leaks, no spills! IF YOU NEED A FILTER SYSTEM TOMORROW CALL US TODAY Pioneers of In-Tank Filtration H

6 THE FLO KING BX3000 Bulletin 14 The BX3000 provides a maximum flow rate of 3,000 gallons per hour. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (8", 10", 12", 14", 16", 18" and 20") enable use of the BX3000 in tanks with varying solution levels and depths. The BX3000 comes complete, preassembled, and ready to operate and includes the items shown in the labeled photograph below. For best results in most metal finishing solutions, use the BX3000 with our PMCA Permacore Magnum reusable or FK50 Poly-Spun disposable filter cartridges in the appropriate length. FLO KING BX3000 SPECIFICATION PUMP MATERIALS: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel (see Bulletin 23.5) as pump materials of construction. Standard shaft is made of Teflon-covered 303 stainless steel. A titanium-tip or Hastelloy-C276-alloy-tip shaft is available on special-order basis. Call for pricing. FLOW RATE: 3000 gallons per hour (11,000 liters per hour) at 60 Hz. A flow-rate reduction of 18%(±3%) is typical when operated at 50 Hz. PRESSURE: 27 feet (8.2 meters) of head pressure WEIGHT: About 24 pounds (10.5 kg) in CPVC, depending on pump body length : Epoxy-coated, TEFC, Thermally Protected. Available in single phase, 1/3 HP (250 watt), 120/240 V, 6.0/3.0 A, 50/60 HZ, 2850/3450 RPM. Specify voltage when ordering. Call for information on 3-phase motors. RUNNING PUMP DRY DOES NOT DAMAGE, PUMP, SEALS OR BEARINGS On-off switch box Universal Bracket screws Universal Bracket Weep hole impeller housing LOCK SCREW FILTER SCREWS (Thumbscrews) Double cartridge holder Important! To ensure proper operation, solution should be 3" (8 cm) or more above Weep Hole on BX3000 pump body. Specify length of pump body when ordering. Use Bulletin 12.1 for prompt sizing recommendations. Handle DRIP COVER (OPTIONAL) Fan cover Motor Motor base Pump body Discharge port 45 elbow Directable outlet extension Thumbscrews on Double Cartridge Holder Filter cartridges install filter plugs here UNIVERSAL BRACKET ADJUSTMENT (4-1/2" TO 7-3/4") 11 to 20 cm (6" X 9") 15 x 23 cm SWIVELING IMPELLER (3-1/2" DIAMETER) 9 cm TOP VIEW Tank 10" (25 cm) 5-3/4" (15 cm) 13" 33 cm 10-1/2" 27 cm (see chart below) 1" PIPE THREAD 2-3/4" (7 cm) Position of pump discharge port and Double Cartridge Holder can be varied 180 to accommodate preferred location in tank. Note: 10" dimension at left includes provision for 45 High-Flow Elbow & 3" Directable Outlet Extension on pump discharge port. MEASUREMENT FROM BOTTOM OF TO DISCHARGE PORT () PUMP MODEL BX BX BX BX BX /4" (22 cm) 10-3/4" (27 cm) 12-3/4" (32 cm) 14-3/4" (37 cm) 16-3/4" (43 cm) BX /4" (48 cm) BX /4" (53 cm)

7 Bulletin 13.9 THE FLO KING BX5000 A FLOW RATE OF 5000 GALLONS PER HOUR (19,000 LPH) USING A TOTALLY ENCLOSED, FAN-COOLED, 3/4-HP (560-WATT) IDEAL FOR FILTRATION OF LARGE TANKS WITHOUT FEAR OF LEAKS OR SPILLS AVAILABLE IN SEVERAL LENGTHS FOR MOST TANK CONFIGURATIONS A CLEAN SOURCE OF AGITATION... AN ALTERNATIVE TO AIR OR MECHANICAL AGITATION HEAVY-DUTY YET STILL PORTABLE... USE IN ONE TANK OR MANY CHANGE FILTERS QUICKLY WITHOUT TOOLS OR DOWNTIME Complete, preassembled, ready to operate. No plumbing. No costly installation. Out of the box and into your tank! IF YOU NEED A FILTER SYSTEM TOMORROW CALL US TODAY Pioneers of In-Tank Filtration H

8 Bulletin 13.9 THE FLO KING BX5000 The BX5000 is excellent for larger tanks or anywhere aggressive agitation is desired. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (8", 10", 12", 14", 16", 18" and 20") enable use of the BX5000 in tanks with varying solution levels and depths. The BX5000 comes complete, preassembled, and ready to operate and includes the items shown in the labeled photograph below. For best results in most metal finishing solutions, use the BX5000 with our PMCA Permacore Magnum reusable or FK50 Poly-Spun disposable filter cartridges in the appropriate length. FLO KING BX5000 SPECIFICATION PUMP MATERIALS: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel (see Bulletin 23.5) as pump materials of construction. Standard shaft is made of Teflon-covered 303 stainless steel. A titanium-tip or Hastelloy- C276-alloy-tip shaft is available on special-order basis. Call for pricing. FLOW RATE: 5000 gallons per hour (19,000 liters per hour) at 60 Hz. A flow-rate reduction of 18% (±3%) is typical when operated at 50 Hz. PRESSURE: 27 feet (8.2 meters) of head pressure WEIGHT: About 29 pounds (13 kg) in CPVC, depending on pump body length : Epoxy-coated, TEFC, Thermally Protected. Available in (specify voltage when ordering): Single phase, 3/4 HP (560 watt), 115/230 V, 9.6/4.8 A, 60 Hz, 3450 rpm. Single phase, 3/4 HP (560 watt), 110/220 V, 9.2/4.6 A, 50 Hz, 2850 rpm. Three phase, 1 HP (760 watt), 220/460 V, 3.0/1.5 A, 60 Hz, 3450 rpm. Note: There is an additional charge for three-phase motors. RUNNING PUMP DRY DOES NOT DAMAGE, PUMP, SEALS OR BEARINGS Handle On-off switch box Universal Bracket screws DRIP COVER (OPTIONAL) Fan cover Motor UNIVERSAL BRACKET ADJUSTMENT (4-1/2" TO 7-3/4") 11 to 20 cm 14-3/4" 38 cm 12-1/16" 31 cm Universal Bracket Weep hole impeller housing LOCK SCREW FILTER SCREWS (Thumbscrews) Double cartridge holder Important! To ensure proper operation, solution should be 4" (10 cm) or more above Weep Hole on BX5000 pump body. Specify length of pump body when ordering. Use Bulletin 12.1 for prompt sizing recommendations. Motor base PUMP BODY Discharge port 45 elbow DIRECTABLE OUTLET EXTENSION Thumbscrews on Double Cartridge Holder Filter cartridges InsTALL filter plugs here (6" X 9") 15 x 23 cm SWIVELING IMPELLER (3-1/2" DIAMETER) 9 cm TOP VIEW Tank 10" (25 cm) 5-3/4" (15 cm) (see chart below) 1" PIPE THREAD 2-3/4" (7 cm) Position of pump discharge port and Double Cartridge Holder can be varied 180 to accommodate preferred location in tank. Note: 10" dimension at left includes provision for 45 High-Flow Elbow & 3" Directable Outlet Extension on pump discharge port. MEASUREMENT FROM BOTTOM OF TO CENTER OF DISCHARGE PORT () PUMP MODEL BX BX BX BX BX /4" (22 cm) 10-3/4" (27 cm) 12-3/4" (32 cm) 14-3/4" (37 cm) 16-3/4" (43 cm) BX /4" (48 cm) BX /4" (53 cm)

9 Bulletin 15.5 FLO KING BX650 A FLOW RATE OF 650 GPH (2400 LPH) USING A TOTALLY ENCLOSED, FAN-COOLED DEVELOPED FOR SMALL TO INTERMEDIATE-SIZE TANKS BUILT IN SEVERAL LENGTHS TO SATISFY FREEBOARD AND TANK DEPTH USE IN ONE LOCATION OR AS A PORTABLE PUMP IN MANY TANKS ACCEPTS STANDARD 2-1/2"-DIAMETER (6.35 cm) FILTER CARTRIDGES Base for mounting on tank is just 4 x 6" (10 x 15 cm). Lightweight, easy-to-use BX650 is more powerful than the Lab Series but less potent than the BX1200. Can be used with popular BX1200 accessories, such as the Double Cartridge Holder, In-Tank Floating Skimmer, and carbon treatment attachments. H IF YOU NEED A FILTER SYSTEM TOMORROW CALL US TODAY H Pioneers of In-Tank Filtration H

10 THE FLO KING BX650 Bulletin 15.5 The BX650 provides a maximum flow rate of 650 gallons (2400 liters) per hour. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (4", 6", 8", and 10") enable use of the BX650 in tanks with varying solution levels and depths. The BX650 comes complete, preassembled, and ready to operate and includes the items shown in the labeled photograph below. For best results in most metalfinishing solutions, use the BX650 with our PMCA Permacore Magnum reusable or FK50 Poly-Spun disposable filter cartridges in the appropriate length. FLO KING BX650 SPECIFICATION PUMP MATERIALS: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel as pump materials of construction. Standard shaft is made of Teflon-covered 303 stainless steel. Titanium and Hastelloy C276 alloy shafts available on special-order basis. Call for pricing. FLOW RATE: 650 gallons per hour (2400 liters per hour) at 60 Hz. A flow-rate reduction of 18% (±3%) is typical when operated at 50 Hz. PRESSURE: 10 feet (3 meters) of head pressure WEIGHT: About 9 pounds (4 kg), depending on pump body length : Epoxy coated, rated at 1/15th HP (50 watt), single phase, 3000 rpm, TEFC, thermally protected. When ordering, specify one of the following three motors: 115 volts, 60 Hz, 2.6 A 115 volts, 50/60 Hz, 2.0 A 230 volts, 50/60 Hz, 1.3 A RUNNING PUMP DRY DOES NOT DAMAGE, PUMP, SEALS OR BEARINGS UNIVERSAL BRACKET SCREW HANDLE DRIP COVER BX650 UNIVERSAL BRACKET (ADJUSTABLE FROM 2-1/4" TO 4-1/2") 5.75 to 11.4 cm 4" 10 cm 7" 18 cm UNIVERSAL BRACKET PUMP BODY (3/8" X 4" X 6") 1 x 10 x 15 cm BODY DIAMETER (1.9") 4.8 cm (see chart below) DISCHARGE PORT FILTER screw (Thumbscrew) 45 ELBOW DIRECTABLE OUTLET EXTENSION IMPELLER DIAMETER (2-7/8") 7 cm 3/4" PIPE THREAD 2" (5 cm) Important! To ensure proper priming, solution must always be above Weep Hole on pump body. Specify length of pump body when ordering. Use Bulletin 12.1 for prompt sizing recommendations. FILTER CARTRIDGE INSERT FILTER PLUG HERE 6.5" (16.5 cm) Tank TOP VIEW BX650 Universal Bracket can be installed at one location on motor base. Bracket can be used on tank lips up to 3/4" (1.9 cm) thick and 4-1/2" (11.4 cm) wide. Note: 6.5" dimension at left includes provision for 45 High-Flow Elbow & Directable Outlet Extension on discharge port. MEASUREMENT FROM BOTTOM OF TO DISCHARGE PORT () PUMP MODEL BX650-4 BX650-6 BX650-8 BX /2" (11 cm) 6-1/2" (17 cm) 9-1/16" (23 cm) 10-3/4" (28 cm)

11 Bulletin 14.5 THE LOW-PROFILE FLO KING BXL2500 LOW PROFILE... JUST 2" (5 cm) ABOVE THE TANK! IDEAL WHERE OVERHEAD OBSTACLES ARE PRESENT FLOW RATE OF 2500 GAL- LONS PER HOUR (9500 LPH) BUILT IN SEVERAL LENGTHS FOR MANY TANK CONFIGURATIONS AN ALTERNATIVE TO AIR OR MECHANICAL AGITATION In addition to our standard BXL2500 with over-the-side motor, this unit is available with Optional Long Motor Base to accommodate tank mounting surfaces up to 6-1/2" (16 cm) wide! Also see our larger low-profile model the 5,000-gallon-per-hour BXL5000 on Bulletin Standard BXL2500 With Long Motor Base Pioneers of In-Tank Filtration H

12 THE FLO KING BXL2500 Bulletin 14.5 The BXL2500 is designed for tanks where overhead clearance is limited. The motor is inverted and positioned outside the tank, taking up only 2" (5 cm) of space above the tank. The unit provides a maximum flow rate of 2500 gallons per hour. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (8", 10", 12", and 14") enable use of the BXL2500 in tanks with varying solution levels and depths. The BXL2500 comes ready to operate and includes the items shown in the labeled photograph below. For best results in most metal finishing solutions, use the BXL2500 with our PMCA Permacore Magnum reusable or FK50 Poly-Spun disposable filter cartridges in the appropriate length. FLO KING BXL2500 SPECIFICATION PUMP MATERIALS: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel (see Bulletin 23.5) as pump materials of construction. Standard shaft is made of Teflon-covered 303 stainless steel. A titaniumtip or Hastelloy-C276-tip shaft is available on special-order basis. Call for prices. FLOW RATE: 2500 gallons per hour (9500 liters per hour) at 60 Hz. A flow-rate reduction of 18%(±3%) is typical when operated at 50 Hz. PRESSURE: 27 feet (8.2 meters) of head pressure WEIGHT: About 25 pounds (11 kg) in CPVC, depending on pump body length : Epoxy-coated, TEFC, Thermally Protected. Available in single phase, 1/3 HP (250 watt), 120/240 V, 6.0/3.0 A, 50/60 HZ, 2850/3450 RPM. Specify voltage when ordering. Call for information on 3-phase motors. RUNNING PUMP DRY DOES NOT DAMAGE, PUMP, SEALS OR BEARINGS ON-OFF SWITCH BOX FAN ADJUSTABLE STAND-OFF FILTER SCREWS (Thumbscrews) Double cartridge holder WEEP HOLE Important! To ensure proper operation, solution should be 3" (8 cm) or more above Weep Hole on pump body. When ordering, specify length of pump body. Also, with standard BXL2500, width of tank lip or flange must be less than 3-1/2" (9 cm) due to fixed space between pump body and motor. Optional Long Motor Base accommodates tank mounting surfaces up to 6-1/2" (16 cm) wide. Use Bulletin 12.1 for sizing recommendations. PUMP PUMP BODY SWIVEL housing LOCK SCREW Discharge port 45 elbow Directable outlet extension Thumbscrews on Double Cartridge Holder Filter cartridges Insert filter plugs here Option For Wide Tank Flanges: With Optional Long Motor Base to accommodate mounting surfaces up to 6-1/2" wide, B Dimension = 15-1/2" (38 cm) and C Dimension = 6-1/2" (16 cm). Specify Long Motor Base with order. 9" (23 cm) 3-1/2 X 4" (9 X 10 cm) 7-1/2" (18 cm) Solution must be maintained below this level (at least 2" below top of tank) Solution must be maintained above this level (at least 3" above Weep Hole) TOP VIEW 2-1/2" (7 cm) Tank B DIMENSION 12" (30 cm) "C" DIMENSION 3-1/2" (9 cm) 10" (25 cm) WEEP HOLE 5-3/4" (15 cm) (see chart below) 2-1/4" (6 cm) 1-1/4" (3 cm) 2-3/4" (7 cm) SWIVELING IMPELLER 3-1/2" (9 cm) diameter 1" PIPE THREADS Position of pump discharge port and Double Cartridge Holder can be varied 180 to accommodate preferred location in tank. Note: 10" dimension at left includes provision for 45 High-Flow Elbow & 3" Directable Outlet Extension on pump discharge port. MEASUREMENT FROM BOTTOM OF PUMP TO BOTTOM OF IMPELLER () PUMP MODEL BXL BXL BXL BXL /4" (28 cm) 12-3/4" (32 cm) 14-3/4" (38 cm) 16-3/4" (43 cm)

13 Bulletin 14.2 THE FLO KING LOW-PROFILE BXL5000 EXTENDS JUST 2" (5 cm) ABOVE THE TANK FOR BARREL, AUTOMATIC, AND OTHER OPERATIONS WITH LIMITED CLEARANCE OVER TANK CAN BE MOUNTED ON TANK FLANGE OR LIP UP TO 6" (15 cm) WIDE Over the Side! PROVIDES A FLOW RATE OF 5,000 GPH (19,000 LPH) BUILT IN SEVERAL LENGTHS FOR MANY TANK CONFIGURATIONS AN ALTERNATIVE TO AIR OR MECHANICAL AGITATION NOW WITH IMPROVED BELT-DRIVE SYSTEM The BXL5000 is an extension of our popular BXL2500 technology with over-the-side motor to avoid above-tank obstructions. This unique model provides filtration and agitation for even larger tanks. Plus, our Long Motor Base design permits installation on tanks with mounting surfaces as wide as 6" (15 cm)! COMPLETE, PREASSEMBLED, READY TO OPERATE. NO PLUMBING. NO COSTLY INSTALLATION. OUT OF THE BOX AND INTO YOUR TANK!

14 THE FLO KING BXL5000 The BXL5000 is designed for tanks where overhead clearance is limited. The motor is inverted and positioned outside the tank, taking up only 2" (5 cm) of space above the tank. The unit provides a maximum flow rate of 5000 gallons per hour. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (8", 10", 12", and 14") enable use of the BXL5000 in tanks with varying solution levels and depths. The BXL5000 comes ready to operate and includes the items shown in the labeled photograph below. For best results in most metal-finishing solutions, use the BXL5000 with our PMCA Permacore Magnum reusable or FK50 Poly-Spun disposable filter cartridges in the appropriate length. FLO KING BXL5000 SPECIFICATION PUMP MATERIALS: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel (see Bulletin 23.5) as pump materials of construction. Standard shaft is made of Teflon-covered 303 stainless steel. A titaniumtip or Hastelloy-C276-tip shaft is available on special-order basis. Call for prices. FLOW RATE: 5000 gallons per hour (19,000 liters per hour) at 60 Hz. A flow-rate reduction of about 18%(±3%) is typical when operating at 50 Hz. PRESSURE: 27 feet (8.2 meters) of head pressure WEIGHT: About 29 pounds (13 kg) in CPVC, depending on pump body length : Epoxy-coated, TEFC, Thermally Protected. Available in (specify voltage when ordering): Single phase, 3/4 HP (560 watt), 115/230 V, 9.6/4.8 A, 60 Hz, 3450 rpm. Single phase, 3/4 HP (560 watt), 110/220 V, 9.2/4.6 A, 50 Hz, 2850 rpm. Three phase, 1 HP (760 watt), 220/460 V, 3.0/1.5 A, 60 Hz, 3450 rpm. Note: There is an additional charge for three-phase motors. RUNNING PUMP DRY DOES NOT DAMAGE, PUMP, SEALS OR BEARINGS Bulletin 14.2 ON-OFF SWITCH BOX PUMP 15-1/2" (40 cm) 2-1/4" (6 cm) FAN ADJUSTABLE STAND-OFF FILTER SCREWS (Thumbscrews) DOUBLE CARTRIDGE HOLDER Important! To ensure proper operation, solution should be 4" (10 cm) or more above Weep Hole on pump body. Specify length of pump body when ordering. Also, width of tank lip or flange must be less than 6" (15 cm) due to fixed space between BXL5000 pump body and motor. Use Bulletin 12.1 for sizing recommendations. WEEP HOLE PUMP BODY SWIVEL LOCK SCREW DISCHARGE PORT 45 ELBOW DIRECTABLE OUTLET EXTENSION FILTER SCREWS ON DOUBLE CARTRIDGE HOLDER FILTER CARTRIDGES INSERT FILTER PLUGS HERE 9" (23 cm) 3-1/2 x 4" (9 x 10 cm) 7-1/2" (19 cm) Solution must be maintained below this level (at least 2" below top of tank) Solution must be maintained above this level (at least 4" above Weep Hole) SWIVELING IMPELLER 3-1/2" (9 cm) diameter TOP VIEW 3-1/2" (9 cm) Tank 6" (15 cm) 10" (25 cm) WEEP HOLE 5-3/4" (15 cm) 1-1/4" (3 cm) (see chart below) 1" PIPE THREADS 2-3/4" (7 cm) Position of pump discharge port and Double Cartridge Holder can be varied 180 to accommodate preferred location in tank. Note: 10" dimension at left includes provision for 45 High- Flow Elbow & 3" Directable Outlet Extension on pump discharge port. MEASUREMENT FROM BOTTOM OF PUMP TO BOTTOM OF IMPELLER () PUMP MODEL BXL BXL BXL BXL /4" (28 cm) 12-3/4" (32 cm) 14-3/4" (38 cm) 16-3/4" (43 cm)

15 Bulletin 16 FLO KING IN-TANK LAB SERIES FILTER SYSTEM For tanks as small as a half-gallon and larger! At last... an in-tank filter system small enough to use in a half-gallon (2-liter) beaker as well as tanks up to several gallons. Your choice of three filter cartridge sizes, plus the ease of clamping to most existing beakers and tanks using an adjustable bracket. Pumps from a few gallons to 400 gallons per hour (up to 1,500 liters/hour) 2" Outlet Extension Air Exhaust Directed Away from Tank 90 High-Flow Elbow Adjustable Universal Bracket 45 High-Flow Elbow All-Way Adjustable Sparger ("Kurt Tube") Disposable, 5-Micron Wound Cartridge (3" Long x 1-1/2" Diameter) & Filter Plug Loading Slats for Reusable Cartridges Mini-Mag Reusable Cartridge (4" Long x 1-1/2" Diameter) & Filter Plug Filter Adapter for 2-1/2"-Diameter Disposable & Reusable Cartridges Magnum Reusable Cartridge (4" Long x 2-1/2" Diameter) Filter Plug for Magnum This is a ready-to-operate filter system complete with all accessories illustrated. It is powered by a super-quiet, ball-bearing, continuousduty motor. IF YOU NEED A FILTER SYSTEM TOMORROW CALL US TODAY Pioneers of In-Tank Filtration H

16 Bulletin 16 FLO KING IN-TANK LAB SERIES FILTER SYSTEM Tomorrow s Filter Technology Today Introducing THE IN-TANK CONCEPT in small bath filtration the Flo King Lab Series system. This unit is ideal for laboratory, prototype, and small-tank production operations in clean settings. Like all Flo King systems, it is a complete, preassembled unit that uses no out-of-tank apparatus and cannot leak or spill. The Lab Series is small enough to filter a half-gallon beaker, yet powerful enough to use in small plating and related tanks generally up to about 10 gallons (40 liters) but sometimes more, depending on agitation requirements, type of solution, and other factors. The flow rate is dependent on the filter element and attachments selected and ranges from a few gallons to 400 gallons per hour (1,500 liters per hour). The Lab Series includes attachments to meet diverse agitation needs two elbows for high flow and a directable dispersion tube ( Kurt Tube ) for gentle, uniform circulation. 3-7/8" (10 cm) "A" DIMENSION 1/2" PIPE THREADS FILTER SCREW 4" (10 cm) 1-7/8" (4.5 cm) 1/4" x 3" x 5" (0.7 x 7.5 x 12.5 cm) 2" (5 cm) Important: To ensure proper operation, solution must be above Weep Hole on pump body. Impeller is just below Weep Hole. PUMP BODY MODEL INCH CM PP-LBS PP-LBS PP-LBS PP-LBS Three filter cartridge sizes are provided to satisfy many filtration requirements. The two Magnum filter cartridges are capable of filtering down below 1 micron and are reusable. The Poly-Wrap is a 1-1/2"-diameter disposable cartridge. In addition, a simple-to-attach Filter Adapter included in the Lab Series package enables the use of any standard 2-1/2"-diameter cartridge, including the popular highquality Flo King Poly-Spun disposables. Our adjustable Universal Bracket allows the filter system to be mounted easily on most tanks without the use of tools. The bracket also provides a secure mount on round beakers and glass battery jars. The Lab Series filter system is a ready-to-use package requiring no tools or training to operate. It is supplied in 115 or 230 volts for your electrical needs and in different pump-body lengths to satisfy the depth and freeboard of your container or tank. For sizing suggestions, just provide the information requested on Bulletin FLO KING LAB SERIES SPECIFICATIONS PUMP: Standard unit is made of polypropylene with Teflon-covered 303 stainless-steel shaft. Pump also available on special-order basis in PVDF (Kynar), stainless steel, and CPVC. Titanium shaft also available (call for pricing). FLOW RATE: Up to 400 gallons per hour (1500 liters per hour) at 60 Hz, depending on type of filter cartridge and attachments used. A flow-rate reduction of 18%(±3%) is typical when operated at 50 Hz. : 1/70th horsepower (11 watt), single phase, thermally protected. When ordering, specify one of the following motors: 115 volts, 50/60Hz, 2600/3000 RPM, 0.96 A 230 volts, 50/60Hz, 2600/3000 RPM, 0.48 A Pioneers of In-Tank Filtration H

17 FILTER SYSTEMS TM The Original 4-in-1 FLO KING Bulletin 17 FLO KING PUMPALL Model PAVS Patent Pending HAND-PRESSURIZED, CHEMICAL-DISPENSING PUMP Pressure-Release Valve Plunger: Pump by hand to pressurize container Tap: Press to dispense liquid Drip-Proof Nozzle Viton Drum Seal (3 sizes provided) Siphon Tube Assembly: Accommodates containers up to 36" (91 cm) deep DISPENSES LIQUIDS QUICKLY AND SAFELY FROM SMALL AND LARGE CONTAINERS! FITS ALL COMMON CONTAIN- ERS AS SMALL AS ONE GALLON (3.8 L) AND AS LARGE AS 50 GALLONS (190 L) SIMPLE TO USE JUST HAND- PRESSURIZE PLUNGER AND PRESS TAP TO DISPENSE NO ELECTRICITY MEANS NO POTENTIAL SPARKING HAZARD ONE-TOUCH FLOW CONTROL DISPENSES PRECISE AMOUNTS OF LIQUID; PUMP CAN ALSO BE USED TO SIPHON ENTIRE CON- TENTS OF CONTAINER MADE OF 100% NON-REACTIVE POLYPROPYLENE WITH VITON DRUM SEAL TO WITHSTAND AGGRESSIVE CHEMICALS DOES NOT LEAK, SPILL OR DRIP PUMPS UP TO 4.5 GALLONS (17 LITERS) PER MINUTE Pioneers of In-Tank Filtration CUSTOM MASTERS, INC. 401 LAKE BENNETT CT., LONGWOOD, FL USA FAX

18 FILTER SYSTEMS TM The Original 4-in-1 FLO KING Bulletin 17 PUMPALL HAND-PRESSURIZED DISPENSING PUMP This versatile pump pays for itself quickly by preventing potentially hazardous spills and ensuring precise, measurable flow control of costly liquid chemicals in storage. Use it for most of your metal-finishing and related chemicals brighteners, additives, acids, caustics, etc. With Viton drum seal and non-reactive polypropylene construction, PumpAll can handle just about any liquid in the shop. Unlike costly electric pumps, PumpAll is safe to operate and simple to use. A few strokes of the plunger will pressurize any container from 1-gallon jugs to 55-gallon drums without the potential sparking hazard that renders electric pumps unsuitable for many applications. Then just press the tap to release precisely measured amounts every time. Drip-proof nozzle helps prevent waste. PumpAll can also siphon the entire contents of one container to another. PumpAll kit includes: precision pump; three Viton drum seals (select the one that fits your container opening); and siphon tubes that adjust from 12 to 36 inches (30 to 91 cm) for use with shallow and deep containers. FLO KING PUMPALL SPECIFICATIONS Pressure Nominal, psi (0.17 to 0.20 MPa); Maximum, 32 psi (0.22 MPa) Operating Temperature 32 to 110 F (0 to 43 C) Storage Temperature -4 to 122 F (-20 to 50 C) Siphon Tube Length 9 to 36" (230 to 920 mm) Container Neck Size Small Drum Seal: 1.7 to 2 inch (44 to 52 mm); Medium Drum Seal: 2.0 to 2.2 inch (52 to 56 mm); Large Drum Seal: 2.2 to 2.4 inch (56 to 60 mm). Drum Seals can be used with internally or externally threaded openings. Maximum Flow Rates at 68 F (20 C) Water, 4.5 gallons per minute (17 liters/min); Oil (SAE 30), 2 gallons per minute (7.5 liters/min) Drum Seal Siphon Pipe Connector Fitting For 30- or 55-gallon containers (113 to 208 liters), Standoff is suggested if spout bumps edge of container. Standoff is available in 3, 4 or 6" lengths (76, 101 or 152 mm). Footpiece PumpAll kit includes pump, three Viton drum seals (select one that fits your container opening), polypro pipe segments for siphon-tube assembly, connector fittings, and footpiece. Optional extension tap features nozzle and 5-foot-long hose to transfer solution to a remote container. Containers with coarse (Buttress) threads require Buttress Adapter for proper seal: 2.5"-diameter (63-mm) adapter fits most U.S. drums. Use 2.25" (57-mm) adapter for most Asian and 2.75" (70-mm) for most European drums. CUSTOM MASTERS, INC. 401 LAKE BENNETT CT., LONGWOOD, FL USA FAX