*607210* OPERATOR AND PARTS MANUAL Rev. 04 ( ) Model Part No.: V V CSA AUTOMATIC CARPET EXTRACTOR

Transcription

1 Model Part No.: V V CSA FALCONt 2800 PLUS AUTOMATIC CARPET EXTRACTOR OPERATOR AND PARTS MANUAL To view, print or download the latest manual, visit: Rev. 0 (0-20) *60720*

2 OPERATION This manual is furnished with each new model. It provides necessary operation and maintenance instructions and an illustrated parts list. Read this manual completely and understand the machine before operating or servicing it. When ordering replacement parts, use the illustrated parts lists section in this manual. Before ordering parts or supplies, be sure to have your machine model number and serial number available. Parts and supplies may be ordered by phone or mail from any authorized parts and service center, distributor or from any of the manufacturer s subsidiaries. MACHINE DATA Please fill out at time of installation for future reference. Model No.- Install. Date - Serial No.- This machine will provide excellent service. However, the best results will be obtained at minimum costs if: S The machine is operated with reasonable care. S The machine is maintained regularly - per the machine maintenance instructions provided. S The machine is maintained with manufacturer supplied or equivalent parts. PROTECT THE ENVIRONMENT Please dispose of packaging materials, old machine components such as batteries, hazardous fluids, including antifreeze and oil, in a safe environmentally way according to your local waste disposal regulations. Always remember to recycle. Tennant Company PO Box 2 Minneapolis, MN 0 Phone: (800) - 80 or (76) Nobles is a registered United States trademark of Tennant Company. Specifications and parts are subject to change without notice. Copyright E2000, 200, 2007, 202, 20 Tennant Company. All rights reserved. Printed in U.S.A. 2 Falcont 2800 Plus (0- )

3 OPERATION TABLE OF CONTENTS SAFETY PRECAUTIONS... GROUNDING INSTRUCTIONS... SAFETY LABEL... 6 MACHINE COMPONENTS... 7 CONTROL PANEL SYMBOLS... 7 SETUP AND OPERATION... 8 MACHINE INSTALLATION... 8 MANEUVERING MACHINE WITHOUT USE OF POWER... 8 FILLING SOLUTION TANK... 8 ADJUSTING CONTROL GRIP HEIGHT... 8 CONNECTING MACHINE TO POWER SOURCE... 9 PRE- OPERATION CHECKS... 9 CLEANING CARPET... 9 OPERATING PRE- SPRAY WAND... ADJUSTING BRUSH HEIGHT... CIRCUIT BREAKERS... ACCESSORY TOOL SETUP AND OPERATION (OPTION)... DRAINING TANKS... 2 MACHINE MAINTENANCE... 2 DAILY MAINTENANCE... WEEKLY MAINTENANCE... MONTHLY MAINTENANCE... QUARTERLY MAINTENANCE... ADJUSTING DRIVE BELT... TRANSPORTING MACHINE... STORING MACHINE... RECOMMENDED STOCK ITEMS... TROUBLE SHOOTING... SPECIFICATIONS... 7 ELECTRICAL DIAGRAMS... 8 PARTS LIST RECOVERY TANK GROUP SOLUTION TANK GROUP DRIVE WHEEL GROUP... 2 REAR PANEL GROUP CONTROL CONSOLE GROUP PICK-UP HEAD GROUP... 0 BRUSH BASE GROUP... 2 PLUMBING GROUP... PUMP BREAKDOWN... 6 OPTIONS... 7 SOLUTION AND VACUUM HOSES... 7 FLOOR TOOL, LOW PRESSURE 0mm ( in)... 8 FLOOR TOOL, LOW PRESSURE 06mm (6 in)... 0 HAND TOOL, 27 mm ( in)... 2 HAND TOOL,CREVICE 76 mm ( in)... 2 HAND TOOL, UPHOLSTERY LOW PRESSURE... Falcont 2800 Plus (07-07)

4 OPERATION SAFETY PRECAUTIONS This machine is intended for commercial use. It is designed exclusively to clean carpets in an indoor environment and is not constructed for any other use. Use only recommended accessory tools and commercially available carpet cleaners intended for machine application. All operators must read, understand and practice the following safety precautions. The following warning alert symbol and the FOR SAFETY heading are used throughout this manual as indicated in their description: WARNING: To warn of hazards or unsafe practices which could result in severe personal injury or death. FOR SAFETY: To identify actions which must be followed for safe operation of equipment. Failure to follow these warnings may result in: personal injury, electrocution, electrical shock, fire or explosion. WARNING: Do Not Use Flammable Liquids Or Operate Machine In Or Near Flammable Liquids, Vapors Or Combustible Dusts. This machine is not equipped with explosion proof motors. The electric motors will spark upon start up and during operation which could cause a flash fire or explosion if machine is used in an area where flammable vapors/liquids or combustible dusts are present. WARNING: Do Not Pick Up Flammable Materials Or Reactive Metals. WARNING: Do Not Operate With Damaged Power Cord. Do Not Modify Plug. Unplug power Cord Before Servicing Machine. If the supply cord is damaged or broken, it must be replaced by the manufacturer or it s service agent or a similarly qualified person in order to avoid a hazard. WARNING: Do Not Use Outdoors. Do Not Expose To Rain. Store Indoors. The following information signals potentially dangerous conditions to the operator or equipment: FOR SAFETY:. Do not operate machine: - With flammable liquids or near flammable vapors as an explosion or flash fire may occur. - Unless trained and authorized. - Unless operator manual is read and understood. - Unless cord is properly grounded. - With damaged cord or plug. - If not in proper operating condition. - In outdoor areas. - In standing water. - With the use of additional extension cords. Only use manufacturer s extension cord equipped with machine which has proper capacity and is grounded. 2. Before operating machine: - Make sure all safety devices are in place and operate properly.. When using machine: - Do not run machine over cord. - Do not pull machine by plug or cord. - Do not pull cord around sharp edges or corners. - Do not unplug by pulling on cord. - Do not stretch cord. - Do not handle plug with wet hands. - Keep cord away from heated surfaces. - Go slow on inclines and slippery surfaces. - Use care when reversing machine. - Report machine damage or faulty operation immediately. - Never allow children to play on or around. - Follow mixing and handling instructions on chemical containers.. Before leaving or servicing machine: - Stop on level surface. - Turn off machine. - Unplug cord from wall outlet. Falcont 2800 Plus (08-0)

5 OPERATION. When servicing machine: - Unplug cord from wall outlet. - Avoid moving parts. Do not wear loose jackets, shirts, or sleeves. - Block machine tires before jacking up. - Use hoist or jack that will support the weight of the machine. - Use manufacturer supplied or approved replacement parts. - Allrepairsmustbeperformedbya qualified service person. - Do not modify the machine from it s original design. 6. When transporting machine: - Turn machine off. - Get assistance when lifting machine. - Unplug cord from wall outlet. - Use a recommended ramp when loading/unloading into/off truck or trailer. - Use tie- down straps to secure machine to truck or trailer. GROUNDING INSTRUCTIONS Machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This machine is equipped with a cord having an equipment- grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed in accordance with all local codes and ordinances. Do not remove ground pin; if missing, replace plug before use. Grounded HoleOutlet Ground Pin Falcont 2800 Plus (07-07)

6 OPERATION SAFETY LABEL The safety label appears on the machine in the location indicated. Replace the label if it is missing or becomes damaged or illegible. WARNING LABEL - LOCATED ON TOP OF THE SOLUTION TANK. 6 Falcont 2800 Plus (07-07)

7 OPERATION MACHINE COMPONENTS Control Console 2. Control Grips. Prespray Wand. Recovery Tank Dome. Recovery Tank 6. Solution Tank Fill Door 7. Solution Tank 8. Wall Rollers 9. Front Caster 0. Inline Solution Filter Strainer. Non- Marking Drive Wheels 2. Brush Base. Accessory Solution Hose Coupler. Brush Pressure Meter. Reverse Release Lever 6. Brush Lever Raise/Lower 7. Vacuum ON/OFF Switch 8. Main ON/OFF Switch 9. Pump ON/OFF Switch 20. Speed Control Knob 2. Power Cord Pigtail 22. Brush Motor Circuit Breaker 2. Drive Motor Circuit Breaker 2. Recovery Tank Drain Hose 2. Cleaning Mode Switch 26. Adjustable Control Console Levers 27. Solution Tank Level Indicator 28. Spray Bar 29. Brush Height Adjustment Knob 0. Vacuum Pick-Up Head CONTROL PANEL SYMBOLS Main Power Vacuum Fast Speed Read Manual Before Operating Pump Brush Pressure Slow Speed Falcont 2800 Plus (08-0) 7

8 OPERATION SETUP AND OPERATION MACHINE INSTALLATION ATTENTION: To prevent damage to machine when uncrating, do not attempt to drive or roll off skid. Carefully lift machine with assistance or use a ramp. Your new machine requires very little setup.. Place recovery tank dome on top of solution tank and secure with two thumbscrews (Figure ). 2. Insert black vacuum hose into dome opening.. Install pre-spray wand into opening on right side of tank, next to control housing (Figure ). PRE-SPRAY WAND RECOVERY TANK DOME FILLING SOLUTION TANK Open fill port door at front of machine and fill with 06 liters (28 gal) of hot water, 60_C (0_F) maximum, and add a recommended liquid cleaning solution to proper dilution ratio (Figure ). FOR SAFETY: When using machine, follow mixing instructions on chemical containers. WARNING: Do Not Use Flammable Liquids Or Operate Machine In Or Near Flammable Liquids, Vapors Or Combustible Dusts. ATTENTION: If using powered cleaning chemicals, mix prior to adding. Wait until completely dissolved before pouring into solution tank. ATTENTION: Always use separate buckets to fill and empty machine. Dirty water in solution tank will clog solution pump system. FIG. MANEUVERING MACHINE WITHOUT USE OF POWER Your machine will glide easily across floor by pushing machine forward (without power). To pull machine backwards, pull reverse release lever backwards (arrow A) and to the right to latch (arrow B). This allows the machine to pull back easily. Be certain brush is raised before transporting. To raise brush, pull brush lever backwards (arrow C) until it latches (Figure 2). C A FIG. ADJUSTING CONTROL GRIP HEIGHT Adjust control grip height to a comfortable operating height (three settings). To adjust, squeeze two levers under console together to raise or lower control grip (Figure ). B FIG. FIG. 2 8 Falcont 2800 Plus (08-0)

9 OPERATION CONNECTING MACHINE TO POWER SOURCE. Connect equipped extension cord to short pigtail cord on machine. 2. Plug extension cord into a grounded power outlet (Figure ). FOR SAFETY: Do not operate machine unless cord is properly grounded. FOR SAFETY: Do not operate machine with the use of additional extension cords. Only use manufacturer s extension cord equipped with machine which has proper capacity and is grounded. Grounded HoleOutlet Ground Pin PRE- OPERATION CHECKS. Vacuum the floor and remove any debris. 2. Inspect the power cord for damage. Replace immediately if damaged.. Check that the spray bar is installed.. Inspect the spray tips for proper spray pattern (See MACHINE MAINTENANCE). CLEANING CARPET FOR SAFETY: Do not operate machine unless operator manual is read and understood. WARNING: Do Not Pick Up Flammable Materials Or Reactive Metals. WARNING: Do Not Use Flammable Liquids Or Operate Machine In Or Near Flammable Liquids, Vapors Or Combustible Dusts.. Turn on main power switch. 2. Select cleaning mode. Position cleaning mode switch towards INTERIM CLEANING or RESTORATIVE CLEANING (Figure 7). FIG. WARNING: Do Not Operate With Damaged Power Cord. Do Not Modify Plug. Unplug power Cord Before Servicing Machine. If the supply cord is damaged or broken, it must be replaced by the manufacturer or it s service agent or a similarly qualified person in order to avoid a hazard.. Attach belt clip to power cord and to your belt (Figure 6). FIG. 6 FIG. 7 RESTORATIVE CLEANING: Use this mode to restore heavily soiled carpet areas. This mode disperses.8 liters ( gal) of solution per minute and recommends that you clean at a slower pace. The restorative cleaning mode must be performed on a regular basis in order for the interim cleaning mode to be effective. INTERIM CLEANING: Use this mode for routine light cleaning. This mode disperses 2.6 liters (0.7 gal) of solution per minute and allows you to clean at a faster pace which will provide less drying time. The interim cleaning mode will be ineffective if the restorative cleaning mode is not performed on a regular basis. Falcont 2800 Plus (08-0) 9

10 OPERATION. Turn vacuum switch on.. Lower brush by depressing thumb latch and moving lever forward (Figure 8). FIG. 8. Turn pump switch on. NOTE: Pump and brush are activated by the control grips. 6. To begin cleaning, rotate control grips forward and adjust speed control knob according to specific cleaning mode (Figure 9): RESTORATIVE CLEANING: M (0 ft) per minute. INTERIM CLEANING: 0 M (00 ft) per minute. FIG Observe brush pressure meter while cleaning, it should read in the Best Cleaning Results range (See ADJUSTING BRUSH HEIGHT). 8. Watch level of foam build-up in recovery tank. If excessive foam appears, pour a quality defoamer chemical into recovery tank. ATTENTION: Do not allow foam to enter float shut- off screen. Foam will damage vacuum motor. Damage caused by foam is not covered by warranty. 9. Turn pump switch off just before stopping to vacuum up excess solution. 0. Check remaining solution in solution tank when cleaning. To check, look at solution tank level indicator at rear of machine. Each mark on hose equals 22 Liters ( gals) of solution (Figure 0). FIG. 0. To pull machine backwards, engage reverse lever. 2. Work away from the wall outlet and power cord to prevent cord damage. FOR SAFETY: When using machine, do not run machine over cord, do not pull machine by plug or cord, do not pull cord around sharp edges or corners, do not unplug by pulling on cord and do not handle plug with wet hands.. To stop the machine, position the machine on a level surface and gradually release the control grips.. After cleaning, perform the Daily Maintenance procedures (See MACHINE MAINTENANCE). 0 Falcont 2800 Plus (08-0)

11 OPERATION OPERATING PRE- SPRAY WAND When cleaning, pre- spray traffic areas and spots using built- in spray wand. To activate wand, turn on main power and pump switches. Remove wand from holder, unlock trigger and spray where needed (Figure ). FOR SAFETY: Before leaving or servicing machine, turn off machine and unplug from wall outlet. 2. Drive motor is protected by a 2. amp. circuit breaker. If breaker trips, allow motor to cool then reset circuit breaker button to resume or contact service center. NOTE: When cleaning on inclines, always clean moving downward, never upward. Never climb inclines that exceed degrees, machine circuit breaker may trip or damage may occur. ACCESSORY TOOL SETUP AND OPERATION (OPTION) FIG. ADJUSTING BRUSH HEIGHT. Lower brush. 2. Rotate speed control knob to slowest setting.. Turn main power switch on.. Rotate control grips forward and hold them.. While reading brush pressure meter, turn brush height adjustment knob until meter reads in the Best Cleaning Results range (Figure 2). The optional accessory tools allow you to clean upholstery and areas that the machine is unable to clean, such as alcoves, stairs, corners and small rooms. For a complete list of accessory tools see the OPTIONS section in this manual NOTE: When cleaning upholstery, always check cleaning instructions sewn in the furniture by manufacturer.. Vacuum area before cleaning. 2. Disconnect vacuum hose from recovery dome and replace with optional extension vacuum hose. Connect optional solution hose to quick disconnect located on top of tank. Then connect optional accessory tool to hoses (Figure ). CIRCUIT BREAKERS FIG. 2 The machine is equipped with two circuit breakers located on control housing at rear of machine.. Brush motor is protected by a. amp. circuit breaker. If breaker should trip, adjust brush height or remove any obstruction in brush. Reset breaker button. FIG.. Turn on Main, Vacuum and Pump switches. Falcont 2800 Plus (08-0)

12 OPERATION. To clean, place tool on area to be cleaned, squeeze trigger and pull tool backwards (Figure ). 2. Remove recovery tank dome and rinse out tank. You can use the spray wand to rinse out recovery tank. Be careful not to spray water into standpipe screen (Figure 6). FIG. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up.. Overlap strokes to avoid streaking. NOTE: When cleaning upholstery, use as little cleaning solution as possible and avoid over wetting. FIG. 6. To drain solution tank, place machine over a drain sink or floor drain, pull solution tank level indicator hose off hose barb and drain (Figure 7). DRAINING TANKS When finished cleaning, the recovery tank and solution tank should be drained and cleaned. FOR SAFETY: Before leaving or servicing machine, turn off machine and unplug cord from wall outlet.. To drain recovery tank, push machine to a drain sink or floor drain and unhook drain hose from rear of machine. Unscrew T-handle from drain hose and drain tank (Figure ). FIG. 7 MACHINE MAINTENANCE To keep machine in good working condition, simply follow machine s daily, weekly and monthly maintenance procedures. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine and unplug cord from wall outlet. ATTENTION: Contact an Authorized Service Center for machine repairs. Machine repairs performed by other than an authorized person will void the warranty FIG. 2 Falcont 2800 Plus (08-0)

13 OPERATION DAILY MAINTENANCE (EVERY HOURS OF USE). Drain and rinse out recovery tank and recovery dome. 2. Remove float shut-off screen and clean. Screen is located in recovery tank (Figure 8). WEEKLY MAINTENANCE (EVERY 20 HOURS OF USE). Inspect spray tips for proper spray pattern: a. Engage the reverse release lever to keep machine stationary (Figure 20). FIG. 8. Drain solution tank. To drain, disconnect the solution tank level indicator hose at rear of machine (Figure 9). FIG. 20 b. Lower brush/pickup head and remove detachable spray bar from brush base. Do not disconnect bar from quick coupler (Figure 2). Raise brush after removing spray bar. c. Turn the main power and pump switches on. d. Holding the spray bar off the floor, briefly rotate control grips and observe spray pattern. Pattern should fan out evenly across the width of the spray bar (Figure 2). FIG. 9. Remove any carpet strands or other debris from brush.. Remove any debris lodged inside vacuum pick-up head. 6. Inspect pigtail cord, cord grip and detachable power cord for damage. Replace immediately if damaged. 7. Clean machine housing with an all purpose cleaner and damp cloth. FIG. 2 e. Clean or replace defective twist- out spray tips if necessary (See MONTHLY MAINTENANCE). 2. Tighten hose cuffs and inspect hose for damage. Falcont 2800 Plus (08-0)

14 OPERATION. Remove bowl filter located underneath machine at front and clean screen. Make sure solution tank is empty before removing filter (Figure 22).. Lubricate wheels and caster with a water resistant grease.. Inspect machine for water leaks.. Inspect machine for loose screws. 6. Check tension of drive belt. Drive belt must be properly adjusted to eliminate any slippage. (See ADJUSTING DRIVE BELT). NOTE: Belt may slip if wet. QUARTERLY MAINTENANCE (EVERY 20 HOURS OF USE) FIG. 22 MONTHLY MAINTENANCE (EVERY 80 HOURS USE). Flush pump system with an acetic acid solution to dissolve alkaline chemical buildup. Follow instructions below: a. Pour L (2 oz.) of an acetic acid solution in solution tank with L ( gal) warm water. FOR SAFETY: When using machine, follow mixing and handling instructions on chemical containers. b. Place machine over floor drain and engage reverse release lever. c. Operate pump for 2 to minutes. d. Allow solution to remain in system overnight in above freezing temperatures. e. Next day, drain solution and run L ( gal) of clean water through system to flush out impurities. 2. Remove spray bar from machine by disconnecting quick coupler. Remove quick release spray tips from spray bar and soak spray tips in an acetic acid solution for up to 6 hours. Do not use pointed objects to unplug tips, damage will occur (Figure 2). Inspect motors for carbon brush wear. Replace brushes when worn to a length of 0 mm (0.8 in) or less. Contact an Authorized Service Center for carbon brush inspection. FOR SAFETY: When servicing machine, all repairs must be performed by a qualified service person. ADJUSTING DRIVE BELT FOR SAFETY: When servicing machine, unplug cord from wall outlet.. Carefully lay machine on its left side. 2. Loosen () bolts on drive motor (Figure 2).. Loosen locknut on belt tension bolt.. Turn belt tension bolt clockwise to tighten belt.. Retighten locknut on belt tension bolt. Do not over tighten belt; belt should flex 2.7 mm (0.0 in) at center. For proper adjustment, belt should represent diagram below. LOOSEN BOLTS BELT TENSION BOLT LOCKNUT FIG. 2 FIG. 2 Falcont 2800 Plus (08-0)

15 OPERATION TRANSPORTING MACHINE STORING MACHINE When transporting the machine by use of trailer or truck, be certain to follow tie- down procedures below: FOR SAFETY: When using machine, go slow on inclines and slippery surfaces.. Raise brush base. 2. Load the machine using a recommended loading ramp.. Position the front of the machine up against the front of the trailer or truck. Once machine is positioned, lower the brush base and disengage the reverse release lever.. Place a block behind each drive wheel to prevent machine from rolling.. Place tie- down straps over the top of the machine to prevent it from tipping. It may be necessary to install tie- down brackets to the floor of your trailer or truck. FOR SAFETY: When transporting machine, use a recommended ramp when loading/unloading into/off truck or trailer, use tie- down straps to secure machine to truck or trailer.. Drain and rinse tanks thoroughly. 2. Store the machine in a dry area with the brush base in the raised position.. Remove the recovery tank dome to promote air circulation. ATTENTION: If storing the machine in freezing temperatures, be certain to drain tanks, purge pump and remove the solution tank filter located under the machine at front. Damage due to freezing temperatures is not covered by warranty. WARNING: Do Not Use Outdoors. Do Not Expose To Rain. Store Indoors. RECOMMENDED STOCK ITEMS Refer to Standard Parts section for recommended stock items. Stock Items are clearly identified with a Bullet preceding the parts description. See example below: TROUBLE SHOOTING PROBLEM CAUSE SOLUTION No power Faulty main power switch. Contact Service Center. Loose power cord connection Connect power cord. Faulty power supply cord. Replace power supply cord. Building circuit breaker has tripped. Determine cause and reset circuit breaker in building. Brush motor does not operate Pump switch is not activated. Turn on pump switch. Control grips are not rotated. Rotate control grips. Brush circuit breaker has tripped. Remove obstruction from brush and reset brush circuit breaker button. Faulty brush motor or wiring. Contact Service Center. Carbon brushes worn. Contact Service Center. Roll Switch (left side) faulty or Contact Service Center. needs adjustment. Loose or broken belt. Replace, or contact Service Center. Falcont 2800 Plus (08-0)

16 OPERATION TROUBLE SHOOTING - continued PROBLEM CAUSE SOLUTION Brush motor operates, but brush Loose or broken brush drive belt. Tighten or replace belt. does not spin Loose set screws on belt pulleys. Tighten set screws. Vacuum motor does not operate Vacuum switch not turned on. Turn on vacuum switch. Faulty vacuum switch or wiring. Contact Service Center. Faulty vacuum motor or wiring. Contact Service Center. Vacuum motor thermal overload activated. Remove obstruction and wait 20 minutes for motor to cool. Poor vacuum recovery Recovery tank is full. Empty recovery tank. Float shut- off screen inside recovery Remove screen and clean. tank is clogged. Pickup head is clogged with debris. Remove debris, use coat hanger. Reverse release lever is hard to engage Pre- spray wand does not spray Vacuum hose connections/cuffs are loose or hose is defective. Vacuum hose is clogged with debris. Dome gasket is defective. Drain hose plug is loose. Recovery tank dome is loose. Vacuum motor is loose. Belt tension too tight. Main and Pump switches not turned on. Trigger locked on wand. Spray tip on wand plugged. Push hose cuffs firmly onto connections. Replace hose if damaged. Remove clogged debris. Replace gasket. Tighten drain plug. Tighten dome screws. Contact Service Center. Readjust belt tension (See Maintenance instructions). Turn Main and Pump switches on. Unlock trigger. Remove spray tip and clean with an acetic acid solution. Bowl filter screen plugged. See Weekly Maintenance Loose or broken wiring. Contact Service Center. Faulty MAIN or PUMP switch. Contact Service Center. Faulty solution pump. Contact Service Center. Machine does not spray solution MAIN switch is not turned on. Turn on MAIN switch. PUMP switch is not turned on. Turn on PUMP switch. Control grips not twisted. Twist control grips forward to start spray, brush and drive motors. Bowl filter screen plugged. Spray tips plugged. Loose or broken wiring. Faulty solenoid valve. Faulty MAIN or PUMP switch. See Weekly Maintenance. See Monthly Maintenance. Contact Service Center. Contact Service Center. Contact Service Center. 6 Falcont 2800 Plus (08-0)

17 OPERATION TROUBLE SHOOTING - continued PROBLEM CAUSE SOLUTION Machine does not spray solution Roll Switch faulty or needs adjustment. Contact Service Center. Faulty solution pump. Contact Service Center. Machine does not move when Reverse release lever engaged. Disengage reverse release lever. rotating control grips MAIN switch not turned on. Turn on MAIN switch. Speed control knob turned to slowest setting. Turn speed control knob to desired setting. 2. amp. circuit breaker tripped. Push breaker button to reset. Loose drive belt. Tighten belt (See Maintenance). Broken drive belt. Replace belt (See Maintenance). Wet drive belt. Dry belt off. Loose or broken wiring. Contact Service Center. Roll Switch or 2 faulty or needs adjustment. Contact Service Center. Speed Control Board faulty or needs Contact Service Center. adjustment. Faulty drive motor or wiring. Contact Service Center. Worn carbon brushes in drive motor. Contact Service Center. SPECIFICATIONS MODEL LENGTH WIDTH HEIGHT WEIGHT SOLUTION TANK CAPACITY RECOVERY TANK CAPACITY SPEED CONTROL CLEANING SPEED (MAX) CLEANING PATH WIDTH SOLUTION PUMP BRUSH MOTOR VACUUM MOTOR WATERLIFT/AIRFLOW DECIBEL RATING AT OPERATOR S EAR, INDOORS ON CARPET POWERCORDLENGTH Falcont 2800 Plus 29 mm ( in) 9 mm (22 in) 092 mm ( in) 09 Kg (2 lb) 06 L (28 Gal) 68L(8Gal) Variable Fwd. 6 m 2 (,000 sq ft) per hour (Deep Extraction Mode) 697 m 2 (7,00 sq ft) per hour (Light Extraction Mode) 9 mm (22 in) 6.9 bar (00 psi) max., 20V, A, gpm.6hp, 800 rpm, 20V, A, 90W 2hp, - stage.7 in, 20V, A 80 mm (7 in) / 2.86 m h (0 cfm) 8dB(A) 2 m (7 ft) Falcont 2800 Plus (08-0) 7

18 ELECTRICAL DIAGRAMS 20V WIRING DIAGRAM GREEN GREEN 6 GREEN ROLL SWITCH BLACK ROLL SWITCH 2 2 BLACK GREEN BLACK VACUUM SWITCH MAIN SWITCH PUMP SWITCH POTENTIOMETER BLACK WHITE BLACK RED kw POWER CORD BLACK WHITE BLACK 9 WHITE BRUSH HEIGHT METER BLACK ORANGE RED WHITE WHT / ORG ORANGE BLACK GREEN RED WHITE AC PINK GRAY AC BLUE 7 WHT/BLK WHITE WHT / ORANGE WHT / ORANGE BLACK BLUE BLK GRAY PINK 8 BLACK WHITE AC AC A+ A/F HI W LO SPEED CONTROL BOARD GREEN BLACK BLACK 6 WHITE RED ORANGE WHT/BLK WHITE WHT/RED CONDUIT TO CHASSIS BROWN WHT / RED. AMP CIRCUIT BREAKER (BRUSH) BLACK 2. AMP CIRCUIT BREAKER (DRIVE) INTERIM/RESTOR SWITCH GREEN BLACK BLACK WHITE WHT/BLK WHT/RED WHT / ORG ORANGE WHITE BLUE PINK GRAY + GREEN GRN / YLW BLACK WHITE BLACK BLACK GREEN DRIVE MOTOR SOLENOID WHITE BROWN LIGHT CLEAN SOLENOID VACUUM MOTOR WHITE SOLUTION PUMP RED GREEN BRUSH MOTOR CORD GREEN WHITE BLACK RED BLACK GREEN BRUSH MOTOR 8 Falcont 2800 Plus (0-2)

19 ELECTRICAL DIAGRAMS 20V LADDER DIAGRAM LINE LINE 2 MAIN SWITCH VACUUM SWITCH POTENTIOMETER VACUUM MOTOR SPEED CONTROL BOARD TERMINALS AC AC A+ A/F HI W LO KW ROLL SWITCH CIRCUIT BREAKER 2. AMP DRIVE MOTOR ROLL SWITCH 2 CIRCUIT BREAKER. AMP + INTERIM/ RESTORATIVE CLEANING SWITCH BRUSH MOTOR PUMP SWITCH INTERIM/ RESTORATIVE CLEANING SOLENOID SOLENOID SOLUTION PUMP Falcont 2800 Plus (08-0) 9

20 PARTS LIST RECOVERY TANK GROUP Falcont 2800 Plus (08-0)

21 PARTS LIST RECOVERY TANK GROUP 0062 ASM., STANDPIPE W/NIPPLE Y 0079 STANDPIPE Y NIPPLE, - /2 PVC 07 DGASKET, WASTE AIR CHAMBER 2020 NUT, FLANGED METAL 806 DFLOAT, SHUT- OFF SCREEN 6 60 DHOSE, VAC INTAKE ASM, DOME W/ELBOW Y DOME, VACUUM Y LABEL, DO NOT ALLOW FOAM Y DGASKET, RECOVERY DOME Y KNOB, RND.2-20 BLK 2 Y 007 WASHER,.28X.7X.0 NYLON TANK, RECOVERY GREEN 0227 STUD, /- 20X 0008 DGASKET, VAC MOTOR DMOTOR, VAC.7/ STG 20V Y 6 0 TERMINAL, MALE.2 RED 2 Y DCARBON BRUSHES 2/PK ASSEMBLY Y INCLUDED IN ASSEMBLY Y DHOUSING, MOTOR, FAN, VENT 9 69 NUT, HEX LOCK.2-20 NYLON WASHER, FLAT / WASHER, FLAT / WASHER, LOCK SPLIT SCREW, HEX.- 8X HINGE, TANK DHOSE, VAC 2 X WHT 26 CLAMP, HOSE, WORMDRIVE, D,.6W 7006 DASM., DRAIN HOSE STOPPER Y KNOB, DRAIN HOSE Y DSTRAP, DRAIN HOSE STOPPER Y WASHER, FLAT.8 FENDER Y 0 09 PLUG, DRAIN HOSE 092 SLEEVE, DRAIN HOSE CLAMP, HOSE - 9/6 STEPLESS 2 60 HOSE, DRAIN 007 CLAMP, HOSE / TO - / GASKET, TUBE D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0-2) 2

22 PARTS LIST SOLUTION TANK GROUP Falcont 2800 Plus (0-2)

23 PARTS LIST SOLUTION TANK GROUP COVER, SOLUTION GREEN HINGE, COVER 0706 RIVET, POP SCREW, #6X/8 PANPHL WASHER, #6 FLAT SCREEN, FILTER TANK, SOLUTION GREEN LABEL, WARNING [EXPL,FIRE,SHK EN/FR/ES] 9 09 DPLUG, QCK CPLR BRS - SER FITTING, BRS STR PM0/PF0 06 FITTING, /MX7/8 CLSNIP 2 02 FITTING, E /8MX/2H 90 NY HOSE, CLEAR.0IDX2 000 TIE, WIRE 6 X2 NYLON 6069 CLAMP, HOSE LABEL, MODEL [NOBLES FALCON PLUS] 7 02 SCREW, /8X- /2 HEX NUT, HEX, STD,.8-6, SS WASHER, FLAT / NUT, HEX / STUD, SPRING TENSION D RECOMMENDED STOCK ITEMS DHOSE, VAC 2 X WHITE CLAMP, HOSE - /6 TO 2- / WELDMENT, CHASSIS SCREW, /8-6X DCASTER, SWIVEL NUT, HEX / WASHER, SPLITLOCK 0.8- S/S WASHER, FLAT / SCREW, /8-6X- / WASHER, SPLITLOCK / WASHER, FLAT / BK PLATE, COUNTER WEIGHT, BLACK 02 SCREW, /2- X2- /2 HXHDCP WASHER, FLAT.70X.28X DWHEEL,.0DX.0W LABEL, FRONT,.0 [NOBLES ICON] SCREW. /6-8X- / HXHDCP (CSA MODEL ONLY) WASHER, 0.6B.2D.09 FLAT (CSA MODEL ONLY) PLATE, LOCK (CSA MODEL ONLY) Falcont 2800 Plus (0-2) 2

24 PARTS LIST DRIVE WHEEL GROUP (S/N MAY20) 9 Replaced By Falcont 2800 Plus (0- )

25 PARTS LIST DRIVE WHEEL GROUP WELDMENT, CHASSIS 2 02 STUD, SPRING TENSION 02 NUT, HEX / WASHER, FLAT /8 608 SCREW, HEX /8-6X- / WASHER, SPLIT LOCK / NUT, HEX, STD,.8-6, SS BEARING, FLANGE WASHER,.26X.7X DWHEEL, ASM LEFT CLUTCH 00 WASHER, FLAT, 0., FENDR WASHER, /6 FOR WASHER, SPLITLOCK SCREW, /6-8X/ PLUG, CAP- BLACK AXLE, DRIVE SHAFT BK BRACKET, PIVOT BRUSH ASM PULLEY, 7/8 BORE AXLE KEY,.2X.2X DBELT, V DRIVE COGGED BK BRACKET, IDLER PIVOT BUSHING,.8X.0X BK LINK, BELT DRIVE WASHER, FLAT WASHER, LOCK / SCREW,.8-6X DWHEEL, ASM RIGHT CLUTCH 28 0 NUT, JAM / WASHER, LOCK PULLEY, IDLER 0028 WASHER, FLAT /8 2 0 SPRING, BELT TENSION 022 SCREW, /8-6X2 HXHDCP 0299 SCREW,.8-6X WASHER, SPLITLOCK WASHER, FLAT / DMOTOR, ELECT VDC (BEFORE JUNE 20) Y 008 DBRUSH, CARBON (BEFORE JUNE 20) TERMINAL, BLADE MALE KEY,.2X.2X NUT, HEX, STD,.8-6, SS 022 SCREW, /8-6X2 HXHDCP PULLEY, / BORE MOTOR 0609 DMOTOR, ELE, VDC 20RPM /HP GEAR (AFTER MAY 20) Y 0690 DBRUSH KIT, MOTOR ( PKG = BRUSHES) (AFTER MAY 20) ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0- ) 2

26 PARTS LIST REAR PANEL LEVER GROUP Falcont 2800 Plus (08-0)

27 PARTS LIST REAR PANEL LEVER GROUP 2066 PLATE, LOCK CONTROL RH WELDMENT, DRAIN HOSE HNGR 0027 WASHER, FLAT / WASHER, SPLITLOCK SCREW, /- 20X/2 TRSPHL PLATE, LOCK CONTROL LH SPACER, SQUEEGEE LIFT LATCH, SQUEEGEE HANDLE DGRIP, HANDLE /XX2- / BK HANDLE, LIFT LEVER DGRIP, HANDLE, RUBBER SCREW, HXHDCP.2-20X WASHER, LOCK.2 96 NUT, HEX LOCK.8-6 NL WASHER, FLAT / BUSHING,.8X.0X.28 D RECOMMENDED STOCK ITEMS WASHER, SPLIT LOCK / SCREW, HEX.8-6X NUT, HEX /6-2- ZINC JOINT, BALL - LIFT ROD ROD, LIFT BRUSH ASM SCREW, HXHDCP.- 8X CLAMP, INSULATED / BK WELDMENT, REAR PANEL, BLACK NUT, HEX, STD,.8-6, SS ROD, PRESSURE SPRING BK LINK, BELT DRIVE SCREW, /8-6X HXHDCP BRACKET, REVERSE HANDLE SCREW, HEX.- 8X SCREW, HEX.8-6X BRACKET, REVERSE LATCH Falcont 2800 Plus (0-2) 27

28 PARTS LIST CONTROL CONSOLE GROUP Replaced By Falcont 2800 Plus (0- )

29 PARTS LIST CONTROL CONSOLE GROUP DGRIP, HANDLE RND BUSHING, 7/8 0 BLACK BRACKET, SWITCH 080 SCREW, 6-2X- /8 PANPHL WASHER, LOCK EXT # DSWITCH, SNAP, W/ BUMP MOUNT, SWITCH SCREW, 0-2X/ TRSPHL 9 09 NUT, KEP NUT, HEX LOCK.2-20 NYLON 2 0 SPACER,.2X.0X.6 NYLON WASHER, FLAT / 086 SCREW, /- 20X- /2 RNDPHL TUBE, HANDLE 0007 DGASKET, CONSOLE BK PANEL, CONTROL DCIRCUITBOARD KIT, INSTALL Y DKNOB, SPEED CONTROL Y DPOTENTIOMETER DSWITCH, ROCKER DPST 20A DSWITCH, ROCKER ON/OFF DECAL, DASH SWITCH, TOGGLE PLATE, CONTROL COVER SCREW, 0-2X/8 TRS PHL SEM LABEL, FLOW CONTROL DBOOT, RUBBER SWITCH BLACK SCREW, 0-2X/ TRSPHL NUT, KEP DBREAKER, CIRCUIT. AMP 076 DBREAKER, CIRCUIT 2. AMP WASHER, INT LCK / NUT, KEP 0-2 NYLON DMETER, AMP 06 NUT, HEX 0-2 NYLON 6 00 RECTIFIER, BRIDGE- 600V AMP WASHER, FLAT, / 8 09 NUT, KEP CONTROL HOUSING GREEN GRIP, STRAIN- RELIEF /2NPT 0228 DCORD, / X YELLOW TUBE, HANDLE ADJUSTMENT 2069 PIN, HANDLE ADJUSTMENT PIN, HANDLE ADJUSTMENT LOCK 2 0 SPRING, LOCK PIN DHARNESS, WIRING SCREW, HEX.- 8X WASHER, LOCK SPLIT. 9 0 CLAMP, INSULATED / ID 0 00 NUT, CONDUIT LOCK /2 NPT 2 0 SCREW, RND 0-2X SLOT NY SCREW, 0-2X/2 TRSPHL 2 02 SCREW, /8X2 SHLDR DCLIP,CORDSTRAINRELIEFYLW 0229 DCORD, /X7 YELLOW SMTH SPRING SCREW, /6-8X2 HXHDCP ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0- ) 29

30 PARTS LIST PICK-UP HEAD GROUP Falcont 2800 Plus (08-0)

31 PARTS LIST PICK-UP HEAD GROUP 02 SPRING, BRUSH PRESSURE 2 06 NUT, LOCK- NYLON INSERT / WASHER, FLAT.70X.28X BK BRACKET, PIVOT BRUSH ASM 09 SLEEVE,.62DX.2L WASHER, POLY /2X- / BK BRACKET, BRUSH MNT ASM, BLK SCREW, /2- X- /2 HXHDCP BOLT, PIVOT SPRING 0 07 SPRING, COMPRESSION PIVOT PIN, PIVOT SPRING SCREW, /8-6X- / HXHDCP NUT, HEX, STD,.8-6, SS 2 00 WASHER, SPLIT LOCK 0. D RECOMMENDED STOCK ITEMS 0299 SCREW,.- 8X.7 HEX SPRING, COMPRESSION SCREW,.8-6X WASHER, SPLITLOCK / WASHER, FLAT / BUSHING, /8 X / NOZZLE, CARPET PICK-UP, BLK DHOSE, VAC INTAKE DCUFF, HOSE.0 BLK 2 09 JOINT, BALL - LIFT ROD ROD, LIFT BRUSH ASM NUT, HEX / WASHER, SPLIT LOCK 0. 2 Falcont 2800 Plus (0-2)

32 PARTS LIST BRUSH BASE GROUP Falcont 2800 Plus (07-07)

33 PARTS LIST BRUSH BASE GROUP 0290 DCORD, 8/X6 BLACK BASE, 22 BLACK WASHER, FLAT M.X.0X DGASKET, BASE PLATE PLATE, BASE SCREW, 0-2X/8 TRSPHL SEM DASM., BRUSH Y DBRUSH, SCRUB 22 CYLINDER Y SCREW,.2-20X0.7 HEX Y DSEAL, BRUSH BEARING 2 Y 0 02 DBEARING, BRUSH 2 Y 2026 DBLOCK, BRUSH BEARING 2 Y DGASKET, BEARING BLOCK Y 2008 PULLEY, BRUSH Y 08 NUT /6 FINJAM Y 2006 SHAFT, BRUSH 22 Y SCREW, SET /- 20X/ TERMINAL, MALE DSCNT BRACKET, BRUSH MOTOR 9 08 NUT, HEX 0-2 KEP DMOTOR, ELE, VDC,.2HP (SN ) DMOTOR, ELE, VDC,.2HP,.0D (REPLACED BY 0699) (SN ) DPULLEY, MOTOR DBELT, TIMING SCREW, SET /- 20X/ GRIP, CORD /8N NYLON BLK 2 06 BOLT, SHOULDER /8 X / BK BRACKET, HEIGHT ADJ, BLK STUD, HGT ADJ DKNOB, TEE /6-8 FEMALE 7002 ASM., SPRAYBAR 22 Y MANIFOLD, SOL. SPRAYBAR 22 Y FITTING, JET # TIP, REPLACEMENT FOR # SEAL, SPRAY NOZZLE Y 0208 FITTING, /8M PLUG BRS SKHD 2 Y FITTING, /8M X /8F ELB STRT Y 092 FITTING, BRS QDC /8M SER 09 COUPLER, QCK /8 SER 020 FITTING, /8F X /8M BARB BRS 6 CLAMP, HOSE WORM D 7 6 HOSE, / X 2.0 GRAY LP 8 09 NUT, CONDUIT /8 LOCK 9 09 NUT, KEP SCREW,TRS0-2X/ ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0- )

34 PARTS LIST Falcont 2800 Plus (0-2) PLUMBING GROUP A C A C D D

35 PARTS LIST PLUMBING GROUP 09 DPLUG, QCK CPLR BRS - SER FITTING, BRS STR PM0/PF0 06 FITTING, /MX7/8 CLSNIP 0 FITTING, /FX/8H HOSE BARB CLAMP, HOSE D DASM, SPRAY WAND Y HOSE, /8 LP GRAY.08 Y 7 00 CLAMP, HOSE /8ID EAR GALV. Y 8 06 FITTING, /M X /8H HOSE BARB 2 Y DHOSE, /ID X 2 BLK RECOIL Y DFITTING, /8 V- JET #800 Y 007 COUPLING, /8F X /8F BRASS Y SPACER, TAPERED Y 208 NIPPLE, /8NPT X 8 LONG Y GUN, SPRAY W/GRIP Y 0706 FITTING, / FPT TEE HOSE, /8 X2 LP GRAY DPUMP, 00 PSI, 20V Y TERMINAL, BLADE ML.2 Y 9 02 TERMINAL, RING # WASHER, FLAT # SCREW, RND 0-2X- / PHL NUT, HEX 0-2 NYLON CLAMP, HOSE, WORMDRIVE, D,.6W HOSE, /2 X2 RED FITTING, /8MX/8F ELB 90_ FITTING, /FX/8M BUSHING FITTING, BRS, STR, PM0/PM0 X.8L [NIP] FITTING, BRS STR PF0/PF DFILTER, SCREEN 80 MESH BOWL Y DSTRAINER, INLINE FILTER 8068 DSLEEVE, FILTER 2 MESH FITTING, BRS, E90, PF0/PM0 000 FITTING, / FX/F ELB _ 06 FITTING, BRS /MX/8H 02 FITTING, PLST /8M X /8H 90_ NY 6 02 CLAMP, HOSE /2 EAR FITTING, / FPT TEE SCREW, 8-2X/8 TRSPHL WASHER, LOCK, INT, 08, SS DVALVE, SOLENOID, 20V 60HZ FITTING, BRS, TEE PF0/PF0/PM0 2 0 FITTING, /MX/H BARB BRS HOSE, PVC, BRD, 0.2ID 0.0OD L, GRAY (6020) 06 FITTING, REDUCER /M X /8M 607 VALVE, CHECK /8FPT X /8MPT FITTING, /8F X /H BARB BRS 7 67 HOSE, /ID X 7/6OD X.08M 8 07 FITTING, /MX/2H BARB HOSE, /8 X0. GRAY 0 02 FITTING, E/8MX/2H 90_ NYLON 09 FITTING, /MX/8H ELB. 90 BRS 2 8 CLAMP, HOSE, WORMDRIVE, D,.W 00 CLAMP, HOSE /8ID EAR GALV. ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0-2)

36 PARTS LIST PUMP BREAKDOWN DKIT, SWITCH PRESSURE 9072 DKIT, SWITCH VITON PSI 90 DKIT, SWITCH DIAPHRAGM DKIT, UPPER PUMP HOUSING 902 DKIT, REPLMT CHECK VALVE D RECOMMENDED STOCK ITEMS 907 DKIT, VITON VALVE 90 DKIT, SHURFLO SERVICE 900 DKIT, LOWER PUMP HOUSING DPUMP, 00 PSI 20V (COMPLETE) 6 Falcont 2800 Plus (08-0)

37 OPTIONS HOSES, SOLUTION AND VACUUM HOSE, SOLUTION /8X.6M/ (OPTIONAL) 6086 HOSE, SOLUTION /8X7.6M/2 (STANDARD) 6087 HOSE, SOLUTION /8X.2M/0 (OPTIONAL) Y 2 09 DFITTING, BRS, QDC, PF0, SER60 Y 09 FITTING, BRS, QDC, PM0, SER60 Y 06 FITTING, BRS, STR, PM0, 2 CLOSE, T 6000 HOSE, VACUUM - /2X.6M/ (OPTIONAL) 600 HOSE, VACUUM - /2X7.6M/2 (STANDARD) 6002 HOSE, VACUUM - /2X.2M/0 (OPTIONAL) Y DCUFF, HOSE - / DCONNECTOR, VAC HOSE - /2 N/S DBAG, HOSE W/DRAW STRING (OPTIONAL) ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (07-07) 7

38 OPTIONS WAND GROUP, LOW PRESSURE, in / 0 mm Falcont 2800 Plus (07-07)

39 OPTIONS WAND GROUP, LOW PRESSURE, in / 0 mm DASM., WAND LOW PRESSURE Y 2000.BK TOOL, FLOOR BLACK Y DECAL, LOW PRESSURE TOOL Y DSHOE, 0MM ( IN) FLR TOOL 2 Y GRIP, HAND ADJ. COMPLETE YY 029 SCREW, /- 20X/8 2 YY GRIP, HANDLE FOAM YY 7 08 SCREW, /- 20X/8 2 Y SLEEVE, HANDLE Y HANDLE, VALVE Y PIN, HANDLE Y 020 NUT, / PUSH BLK 2 Y 2 00 FITTING, /MX/F STR Y 09 DFITTING, /F QD CPLR SER 60 Y 200 DVALVE, FLOW CONTROL YY 9060 DKIT, VALVE PIN AND SPRING Y ASM, HOSE LOW PRESSURE Y FITTING, /MX- /8HEXNIP Y WASHER,.X.87X.062 WAND Y ASM., SPRAYBAR WO/TIPS YY CROSS, / FPT YY FITTING, /MX2 NIPPLE 2 YY2 00 FITTING, /FX/F ELBOW 90 2 YY SPRAY BODY, / MALE Y DFILTER, SCREEN 00 MESH Y DFITTING, TIP 00 T- JET Y DCAP, SPRAY BODY Y FITTING, /MX7/8 CLSNIP N/S SQUEEGEE ASSY, 80MM/.0, COMPLT (OPTION - FOR HARD FLOOR SURFACES) ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0-2) 9

40 OPTIONS WAND GROUP, LOW PRESSURE, 6 in / 06 mm Falcont 2800 Plus (07-07)

41 OPTIONS WAND GROUP, LOW PRESSURE, 6 in / 06 mm 2000 DASM., FLOOR TOOL Y 200.BK TOOL, FLOOR 06MM (6 IN) Y DECAL, LOW PRESSURE TOOL Y DSHOE, 06MM (6 IN) FLR TOOL 2 Y GRIP, HAND ADJ. COMPLETE YY 029 SCREW, /- 20X/8 2 YY GRIP, HANDLE FOAM YY 7 08 SCREW, /- 20X/8 2 Y SLEEVE, HANDLE Y HANDLE, VALVE Y PIN, HANDLE Y 020 NUT, / PUSH BLK 2 Y 2 00 FITTING, /MX/F STR Y 09 DCOUPLER, SER. 60 Y 06 NIPPLE, CLOSE / Y 200 DVALVE, FLOW CONTROL YY DKIT, VALVE PIN AND SPRING Y ASM, HOSE LOW PRESSURE Y FITTING, /MX- /8HEXNIP Y WASHER,.X.87X.062 WAND Y ASM., SPRAYBAR 6 WO/TIPS YY FITTING, /F TEE YY FITTING, /F X /F X /M 2 YY FITTING, /MX2 NIPPLE 2 YY2 00 FITTING, /FX/F ELBOW 90 2 YY SPRAY BODY, / MALE Y DFILTER, SCREEN 00 MESH Y DFITTING, TIP 00 T- JET Y DCAP, SPRAY BODY ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (0-2)

42 OPTIONS HAND TOOL, in / 27 mm DASM., HAND TOOL SERIES 60 Y 200.BK TOOL, HAND BLACK Y 2 09 FITTING, BRS QDC PF0 SER60 Y 0606 FITTING, BRS STR PF0 HEX NIP 2 Y LEVER, K- VALVE W/PIN Y 2020 DVALVE, FLOW CONTROL 0PF Y KIT, K- VALVE REPAIR Y PIN, ROLL 0.87D X 0.6L Y 8 00 FITTING, BRS E PF0/PF0 Y FITTING, BRS STR PF02 SWIVEL Y FILTER, SCREEN 00MESH Y DFITTING, BRS TIP, 8002 T- JET Y CAP, NOZZLE SPRAY (8002) HAND TOOL, CREVICE, in / 76 mm DTOOL, CREVICE LP/HP SER 60 Y 2006.BK TOOL, CREVICE BLACK Y DFITTING, TIP #002 /8V- JET Y 200 DVALVE, TOGGLE 02PF W/NUT Y POSITIONER, VALVE HANDLE Y 6006 HOSE, SOLUTION CREVICE TOOL Y FITTING, BRS STR PF0/PF02 Y 7 09 FITTING, BRS QDC PF0 SER 60 ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS 2 Falcont 2800 Plus (07-07)

43 OPTIONS HAND TOOL, UPHOLSTERY, LOW PRESSURE DTOOL, UPHOLSTERY LP SER 60 Y 2008 COVER, UPHOLSTERY TOOL Y GASKET, COVER Y 906 DKIT, SERVICE LP UPHOLSTERY Y DVALVE, WATER/SOL 20VAC LP Y DFITTING, SS TIP /8K- JET Y SCREW, #06-2 X 0.7 Y TRIGGER, UPHOLSTERY TOOL Y DHOSE, VAC UPHOLSTERY TOOL W/O CUFFS Y DHOSE, UPHOLSTERY TOOL Y FITTING, BRASS ( PCS) Y FILTER, INLINE COMPLETE Y SCREEN ONLY, INLINE FILTER Y 0606 FITTING, BRS STR PF0 HEX NIP Y 09 DFITTING, BRS QDC PF0 SER 60 ASSEMBLY Y INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Falcont 2800 Plus (07-07)