SUBMITTAL DATA BAYVIEW SENIOR CENTER. City of Pensacola. for. Sold to. Prepared for. Air-Tech / Darren Wood. Job Number: AZIK4A.

Transcription

1 SUBMITTAL DATA for BAYVIEW SENIOR CENTER Sold to Prepared for City of Pensacola Job Number: AZIK4A Customer PO#: Prepared by Air-Tech / Darren Wood 6/6/2018 Job Name: BAYVIEW SENIOR CENTER 2 of 25

2 Technical Data Sheet for A CC-1 Technical Data Sheet for ACC-1 Job Information Job Name BAYVIEW SENIOR CENTER Date 6/6/2018 Submitted By Darren Wood Software Version Unit Tag ACC-1 Unit Overview Model Number Capacity ton IPLV.IP* EER Btu/W.h Technical Data Sheet Voltage Unit Starter Type Across the AGZ050E V / 60.0 Hz / 3 Ph Line * IPLV reflects AHRI standard rating conditions and does not change with user defined conditions. 1 Previously LEED EA Credit 4 Under LEED V2009 ASHRAE 90.1 '07, '10, '13 & '16 LEED Enhanced Refrigerant Management Credit 1 Pass Unit Water Volume: Connection Hand: Connection Size: Insulation: Entering Fluid Temperature Unit Type Platform Unit Revision Air-Cooled Scroll Compressor Chiller Packaged 00 Head Pressure VFD w/o Line Reactors [Low Ambient] Unit Controls Electronic Expansion Valve Refrigerant Type R410A Pump Controls Dual Evaporator Pumps - Dual Control Output Approval ETL/cETL, AHRI & ASHRAE 90.1 Evaporator 2.6 gal Left Hand Connections 2.5 in Single Layer Insulation to Suction at each Compressor Leaving Fluid Temperature Fluid Type F F Water Fluid Flow gpm Tubing Replaceable Filter Dryer with Discharge & Liquid Valves, no HGBP Fluid Flow Min / Max 72.5/ gpm Note: Evaporator Pressure Drop includes Factory Installed Strainer. Pressure drop without strainer is Coil Fins: Guards: MicroChannel (Epoxy Coating) Condenser Coil Wire Grilles only Condenser Display On Controller only Pressure Drop 20.3 ft H₂O Refrigerant Weight 46 lb (per unit) Pressure Drop Min / Max 6.20 / 40.0 ft H₂O Fouling Factor F.ft².h/Btu Design Ambient Air Temperature Altitude Fan Diameter Minimum Design Ambient Temperature 95.0 F ft 30.0 in 26.0 F Job Name: BAYVIEW SENIOR CENTER 4 of 25

3 Technical Data Sheet for ACC-1 Unit Performance Design Capacity Input Power Efficiency (EER) IPLV.IP* (EER) ton kw Btu/W.h Btu/W.h Point # % Load Capacity ton Performance Points rated at AHRI Ambient Relief Unit Evaporator Condenser Input Power Fluid Flow kw gpm Efficiency (EER) Btu/W.h Pressure Drop ft H₂O Entering Fluid Temperature F Leaving Fluid Temperature F Ambient Air Temperature F Altitude ft This load point is below the chiller minimum load This load point is below the chiller minimum load. * IPLV reflects AHRI standard rating conditions and does not change with user defined conditions Note: Evaporator Pressure Drop in this table does Not include strainer. For strainer pressure drop data see 'Evaporator' table on page 1. Sound (without insulation) Sound Pressure (at 30 feet) 63 Hz 125 Hz 250 Hz 500 Hz 1 khz 2 khz 4 khz 8 khz Overall 75% Load 50% Load 25% Load A A A A Sound Power 63 Hz 125 Hz 250 Hz 500 Hz 1 khz 2 khz 4 khz 8 khz Overall 75% Load 50% Load 25% Load A A A A Octave band is non 'A' weighted and overall readings are 'A' weighted. Sound data rated in accordance with AHRI Standard-370. Physical Unit Length* Height Width* Shipping Weight* Operating Weight* 94 in 100 in 88 in 3093 lb 3114 lb * Shipping and operating weights do not include the weights of any Options or Accessories. Contact Chiller Applications for additional information. Job Name: BAYVIEW SENIOR CENTER 5 of 25

4 Technical Data Sheet for ACC-1 Electrical Unit Electrical Data Voltage Starter Type Fan Motor Quantity LRA Fan Motor (each) FLA Fan Motors (each) 208 V / 60.0 Hz / 3 Ph Across the Line 4 23 A 5.8 A Power Connection Type: Short Circuit Current Rating: Phase Voltage: MCA: Fuse Size (recommended): Fuse Size (maximum): Connector Wire Range: Single Point Disconnect Switch with Circuit Protection 5 ka Phase & Under/Over Voltage Protection with LED A 250 A 250 A (2) 3/0-500MCM Single Point Power Connection Compressor Electrical Data Compressor Type Compressor Quantity Starter Type Scroll 4 Across the Line Circuit #: 1 2 Compressor #: RLA: 51.3 A 51.3 A 51.3 A 51.3 A Inrush Current: 300 A 300 A 300 A 300 A Note: Power wiring connections to the chiller may be done with either copper or aluminum wiring. Wire should be sized per NEC and/or local codes. Wire sizing and wire count must fit in the power connection lug sizing listed in latest installation manual. Please contact your local sales office for more information. Options Control Box Ambient: Suction Shut-off Valve: Evaporator Strainer: Communication: Ground Fault: Water Flow Indicator: Basic Unit High Ambient with Exhaust Fans (125ºF maximum) Included Factory Installed Evaporator Strainer 175 PSI Pressure Rating Control BACnet MS/TP Electrical Unit Ground Fault Protection Thermal Dispersion Type Warranty Unit Startup Standard Warranty: Extended Unit Warranty: Refrigerant Warranty By Others 1st Year Entire Unit Parts & Labor Entire Unit; Extended 4 years parts & labor (5 Years Total) 5 Years Total AHRI Certification Certified in accordance with the AHRI Air-Cooled Water-Chilling Packages Using Vapor Compression Cycle Certification Program, which is based on AHRI Standard 550/590 (I-P) and AHRI Standard 551/591 (SI). Certified units may be found in the AHRI Directory at Accessories Part Number Optional Description RIS Isolator Kit; AGZ: Packaged, Microchannel,Al&Cu Fins, E (non-seismic),25-65d,30-65c; M'Chnl,75-100E (non-s'mc); Al Fin,70C/D;Remote,Al&Cu Fin,30-70E (non-s'mc); Pump Pkg, M'Chnl&Al Fin,30-65E (non-s'mic); Cu Fin,30-55E(non-S'mic) Job Name: BAYVIEW SENIOR CENTER 6 of 25

5 Item Summary for ACC-1 Item Summary for ACC-1 Job: BAYVIEW SENIOR CENTER Model: AGZ050E Date: 6/6/2018 Tag: ACC-1 Version: Unit Options: Code Code Item Value Description 1 AGZ UNIT TYPE; AIR COOLED SCROLL CHILLER 2 050E UNIT SIZE; 050E 3 D NUMBER OF COMPRESSORS; 2 Compressors per Circuit 4 SE PLATFORM; Standard Package - Standard Eff. 5 FP CONSTRUCTION; Fully Painted (with Unit Wraps) 6 ST SOUND; Standard Sound 7 S UNIT OPERATION; Standard Operation (40F-50F LWT) 8 P CONDENSER COIL FINS; MicroChannel (Epoxy Coating) 9 AL COMPRESSOR STARTER; Across the Line 10 Y FUTURE; Future VOLTAGE; 208V/60HZ/3PH 12 DC POWER CONNECTION; Single Point Disconnect Sw. & Circuit Protection 13 V PHASE VOLTAGE; Phase & Under/Over Voltage Protection w/ LED 14 N FUTURE; None 15 H CONTROL BOX AMBIENT; With Exhaust Fans & Vents 16 N COMPRESSOR CAPACITOR; None 17 BT COMMUNICATION; Intelligent Equipment & BACnet MS/TP 18 N DISPLAY OPTIONS; On Controller Only 19 G GROUND FAULT; W/ Ground Fault Protection for the Unit 20 Y FUTURE; Future 21 N UNIT OPTIONS; No Unit Options 22 B WATER FLOW; Factory Installed Strainer & Flow Indication 23 LH EVAPORATOR CONNECTION; Left Hand Connections 24 B EVAPORATOR INSULATION; Single Layer Insulation to Suction at each Compr. 25 E UNIT CONTROLS; Electronic Expansion Valve 26 L FANS; Standard Low Noise Fan Motors 27 D HEAD PRESSURE; VFD without Line Reactors 28 G GUARDS; Condenser Coil Wire Grilles only 29 VN TUBING OPTIONS; Repl. Filter Dyer, w/ Disch. & Liq. Valves, No HG 30 V SUCTION VALVE; Shut-off Valve 31 NN WATER PUMP; None 32 NNNN PUMP TYPE; No Pump Package 33 N FACTORY USE ONLY; N/A PUMP FLOW; Gallons per minute TOTAL HEAD; Feet 36 N PUMP PACKAGE STARTER; None 37 N PUMP GAUGES; None 38 N PUMP SUCTION VALVE; None 39 N PUMP DISCHARGE VALVE; None 40 Y FUTURE; Future 41 NNNN IMPELLER TRIM; None 42 NN EXPANSION TANK; None 43 NN BUFER TANK; None PERCENT OF GLYCOL; None PUMP PART NUMBER; Pump Package Part Number 46 E APPROVALS; ETL/CETL, AHRI & ASHRAE N CRN EVAPORATOR; None 48 NSU UNIT START; Startup by Others Job Name: BAYVIEW SENIOR CENTER 8 of 25

6 Item Summary for ACC-1 Code Code Item Value Description 49 DPN STANDARD WARRANTY; Domestic, 1 Year Standard Warranty-Parts Only 50 Y FUTURE; Future 51 NNNN EXT COMPRESSOR WARRANTY; None - No Extended Compressor Warranty 52 AE1 FIRST YEAR LABOR WARRANTY; Entire Unit 53 EBE4 EXTENDED UNIT WARRANTY; Entire Unit - Ext. 4 Year Parts & Labor 54 RA5 REFRIGERANT WARRANTY; 5 Year R410A Refrigerant 55 D00 DELAYED WARRANTY START; Additional Months:0 [12-18] Standard 56 D2 FIELD OPTIONS; Dual Evaporator Pumps - Dual Control Output 57 J BRAND NAME; Daikin 58 S SHIP; Standard Ship 59 NN RESTART; Standard 60 Y FUTURE; Future 61 S UNIT MISC; Standard Unit UNIT REVISION; Major Unit Change Revision 63 B SHIPPING/PACKAGING; Bagged 64 F0 TESTING; Functional Test Accessories: Part Number Description Qty Ext Qty RIS Isolator Kit; AGZ: Packaged, Microchannel,Al&Cu Fins, E (non- Seismic),25-65D,30-65C; M'Chnl,75-100E (non- S'mc); Al Fin,70C/D;Remote,Al&Cu Fin,30-70E (non-s'mc); Pump Pkg, M'Chnl&Al Fin,30-65E (non-s'mic); Cu Fin,30-55E(non-S'mic) 1 1 Job Name: BAYVIEW SENIOR CENTER 9 of 25

7 AGZ-E Cl ose S paci ng_drawi ng for AC C-1 AGZ-E Close Spacing_Drawing for ACC-1 AGZ-E Close Spacing Performance Case 1: Building or Wall on One Side of Unit Assumes a solid height wall taller than unit. Refer to Case 4 for partial wall openings. Building or Wall on One Side of Unit For models AGZ E, maintain a 4 feet minimum from a wall of any height. For models AGZ E, maintain a 6 feet minimum from a wall of any height. For models AGZ E, maintain an 8 feet minimum from a wall of any height. 0A Case 2: Two Units, Side-by-Side For models , there must be a minimum of 4 feet between two units placed side-by-side; however, performance may be affected at this distance. For models , the minimum is 6 feet as closing spacing may cause air recirculation and elevated condenser pressure. Assuming the requirement of one side having at least 8 feet of service clearance is met, Case 2 figures show performance adjustments as the distance between two units increases. Two Units, Side-by-Side Case 2 - Full Load Capacity Reduction Case 2 Power Increase Product Drawing Unit Tag: ACC-1 Product: Air-Cooled Scroll Chiller Project Name: BAYVIEW SENIOR CENTER Model: AGZ-E Sales Office: Air-Tech of Pensacola Sales Engineer: Darren Wood June 06, 2018 Ver/Rev: Sheet 1 of 1 Scale: NTS Tolerance: +/-1.0 Dwg Units: in [mm] Industrial Park Blvd. Minneapolis, MN Software Version: No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications. Job Name: BAYVIEW SENIOR CENTER 10 of 25

8 AGZ-E Close Spacing_Drawing for ACC-1 Case 3: Three or More Units, Side-by-Side For all models, there must be a minimum distance between any units placed side-by-side; however, performance may be affected at this distance. Minimum distances are: models 030 to feet, models 075 to feet, models 110 to feet. The Case 3 charts below depict Case 3 performance adjustments as the distance between units increases. Data shown is for the middle unit with a unit on each side. See Case 2 adjustment factors for the two outside units. Three or More Units, Side-by-Side Case 3 Full Load Capacity Reduction Case 3 Power Increase Job Name: BAYVIEW SENIOR CENTER 11 of 25

9 AGZ-E Close Spacing_Drawing for ACC-1 Case 4: Open Screening Walls Decorative screening walls are often used to help conceal a unit either on grade or on a rooftop. When possible, design these walls such that the combination of their open area and distance from the unit (see chart below) do not require performance adjustment. If the wall opening percentage is less than recommended for the distance to the unit, it should be considered as a solid wall. It is assumed that the wall height is equal to or less than the unit height when mounted on its base support. If the wall height is greater than the unit height, see Case 5: Pit Installation for performance adjustment factors. The distance from the sides of the unit to the side walls must be sufficient for service, such as opening control panel doors. For uneven wall spacing, the distance from the unit to each wall can be averaged providing no distance is less than 4 feet. Values are based on walls on all four sides. Case 4 - Allowable Wall Open Area Case 5: Pit Installation Pit installations can cause operating problems resulting from air recirculation and restriction and require care that sufficient air clearance is provided, safety requirements are met and service access is provided. A solid wall surrounding a unit is substantially a pit and this data should be used. Steel grating is sometimes used to cover a pit to prevent accidental falls or trips into the pit. The grating material and installation design must be strong enough to prevent such accidents, yet provide abundant open area to avoid recirculation problems. Have any pit installation reviewed by the Daikin Applied sales representative prior to installation to ensure it has sufficient air-flow characteristics and approved by the installation design engineer to avoid risk of accident. Models AGZ E: The Case 5 figures for models AGZ E show adjustment factors for pit/wall heights of 4 feet, 5 feet, and 6 feet. Case 5 - Full Load Capacity Reduction and Power Increase (AGZ030E-070E) Case 5- Pit Installation KEY: : Power Increase : Capacity Reduction Job Name: BAYVIEW SENIOR CENTER 12 of 25

10 AGZ-E Close Spacing_Drawing for ACC-1 Models AGZ E: The Case 5 figures for models AGZ E show adjustment factors for pit/wall heights of 5 feet, 6 feet, and 8 feet. Case 5 - Full Load Capacity Reduction and Power Increase (AGZ E) KEY: : Power Increase : Capacity Reduction Models AGZ E: The Case 5 figures for models AGZ E show adjustment factors for pit/wall heights of 6 feet, 8 feet, and 10 feet. Case 5 - Full Load Capacity Reduction (AGZ E) Case 5 - Power Increase (AGZ E) Case 5 - Full Load Capacity Reduction (AGZ E) Case 5 - Power Increase (AGZ E) Job Name: BAYVIEW SENIOR CENTER 13 of 25

11 AGZ E_ CndGrl_wr ps_ Drawing for A CC -1 Job Number: Job Name: AZIK4A BAYVIEW SENIOR CENTER 14 of 25 Page Prepared Date: 6/6/2018 AGZ-E Guards: Condenser Coil Wire Grilles, Front and Rear Wraps, Painted Base Product Drawing Unit Tag: ACC-1 Sales Office: Air-Tech of Pensacola Product: Air-Cooled Scroll Chiller Project Name: BAYVIEW SENIOR CENTER Sales Engineer: Darren Wood Model: AGZ E June 06, 2018 Ver/Rev: Sheet: 1 of 1 Scale: N/A Tolerance: N/A Dwg Units: N/A Diagram Notes Diagram simulates wrap, grille and louver options as selected only. Refrigeration components may vary depending on selected options Industrial Park Blvd. Minneapolis, MN Software Version: No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications. 00 AGZ E_CndGrl_wrps_Drawing for ACC-1

12 AGZ050E_ PKG_MCC_Draw ing for ACC-1 Job Number: Job Name: AZIK4A BAYVIEW SENIOR CENTER 15 of 25 Page Prepared Date: AGZ050E Packaged (Microchannel Condenser) Unit Dimensions Units Unit Weight Data Weight Lifting Weight Mounting Weight Shipping Operating L1 L2 L3 L4 M1 M2 M3 M4 lb kg Units A (No Strainer) Unit and Center of Gravity Dimensions B (With Strainer) Connection Size (Victaulic) Center of Gravity X Y Z in mm NOTE IT IS RECOMMENDED THAT THE SIDE LOCATIONS BE USED FOR POWER ENTRY WIRE SIZES LARGER THAN 350 MCM. NOTE A water strainer must be installed at the inlet of the evaporator to protect it from damage. Please refer to the IOM for additional details. 0A AGZ050E_PKG_MCC_Drawing for ACC-1 6/6/2018 Product Drawing Unit Tag: ACC-1 Sales Office: Air-Tech of Pensacola Product: Air-Cooled Scroll Chiller Project Name: BAYVIEW SENIOR CENTER Sales Engineer: Darren Wood Model: AGZ050E June 06, 2018 Ver/Rev: Sheet: 1 of 1 Scale: NTS Tolerance: +/- 1.0" Dwg Units: in [mm] Industrial Park Blvd. Minneapolis, MN Software Version: No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

13 AGZE_Cleara nce_mcc_dra wing for ACC-1 Job Number: Job Name: AZIK4A BAYVIEW SENIOR CENTER AGZ-E Service Clearance 0B AGZE_Clearance_MCC_Drawing for ACC-1 16 of 25 Page Prepared Date: *NOTE: Additional clearance is required for proper airflow. Please consult Close Spacing drawings and IOM for additional details. 6/6/2018 Product Drawing Unit Tag: ACC-1 Sales Office: Air-Tech of Pensacola Product: Air-Cooled Scroll Chiller Project Name: BAYVIEW SENIOR CENTER Sales Engineer: Darren Wood Model: AGZ-E June 06, 2018 Ver/Rev: Sheet: 1 of 1 Scale: NTS Tolerance: +/- 1.0" Dwg Units: in [mm] Industrial Park Blvd. Minneapolis, MN Software Version: No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

14 IsoKit_RIS_ _Drawi ng for ACC-1 Job Number: Job Name: AZIK4A BAYVIEW SENIOR CENTER Rubber-in-Shear (RIS) Isolator Kit Dimensions and Placement Mounting Location M1 M2 M3 M4 Brown Brown Brown Brown M3 M1 00 IsoKit_RIS_ _Drawing for ACC-1 17 of 25 Page Prepared Date: M4 Control Panel M2 6/6/2018 Product Drawing Unit Tag: ACC-1 Sales Office: Air-Tech of Pensacola Accessory: Rubber-in-Shear (RIS) Isolator Kit Project Name: BAYVIEW SENIOR CENTER Sales Engineer: Darren Wood Kit Part Number: June 06, 2018 Ver/Rev: Sheet: 1 of 1 Scale: NTS Tolerance: +/- 1.0" Dwg Units: in [mm] Industrial Park Blvd. Minneapolis, MN Software Version: No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications.

15 FieldWiri ng_agze_s P_Drawi ng for AC C-1 FieldWiring_AGZE_SP_Drawing for ACC-1 AGZ E Single-Point Connection Field Wiring Diagram 0D Field Wiring Diagram Unit Tag: ACC-1 Product: Air-Cooled Scroll Project Name: BAYVIEW SENIOR CENTER Model: AGZ E Single-Point Sales Office: Air-Tech of Pensacola Sales Engineer: Darren Wood June 06, 2018 Ver/Rev: Sheet 1 of 1 Scale: N/A Tolerance: N/A Dwg Units: N/A Industrial Park Blvd. Minneapolis, MN Software Version: No change to this drawing may be made unless approved in writing by Daikin Applied. Purchaser must determine that the equipment is fit and sufficient for the job specifications. Job Name: BAYVIEW SENIOR CENTER 18 of 25

16 Specificati on for A CC -1 Specification for ACC-1 PART 1: GENERAL 1.01 SUMMARY A. Section includes design, performance criteria, refrigerants, controls, and installation requirements for air-cooled scroll compressor chillers REFERENCES A. Comply with applicable Standards/Codes of AHRI 550/590, ANSI/ASHRAE 15, ETL, cetl, NEC, and OSHA as adopted by the State. B. Units shall meet the efficiency standards of the current version of ASHRAE Standard 90.1, and FEMP standard SUBMITTALS A. Submit shop drawings and product data in accordance with the specifications. B. Submittals shall include the following: 1. Dimensioned plan and elevation view drawings, required clearances, and location of all field connections 2. Summary of all auxiliary utility requirements such as electricity, water, etc. Summary shall indicate quality and quantity of each required utility. 3. Single line schematic drawing of the field power hookup requirements, indicating all items that are furnished. 4. Schematic diagram of control system indicating points for field interface/connection. 5. Diagram shall fully delineate field and factory wiring. 6. Installation and operating manuals QUALITY ASSURANCE A. Qualifications: Equipment manufacturer must specialize in the manufacture of the products specified and have five years experience with the type of equipment and refrigerant offered. B. Regulatory Requirements: Comply with the codes and standards specified. C. Chiller manufacturer plant must be ISO Registered DELIVERY AND HANDLING A. Chiller shall be delivered to the job site completely assembled and charged with refrigerant and oil by the manufacturer. B. Comply with the manufacturer's instructions for rigging and handling equipment WARRANTY A. Standard Warranty (Domestic): The refrigeration equipment manufacturer's guarantee shall be for a period of one year from date of equipment start-up but not more than 18 months from shipment. The guarantee shall provide for repair or replacement due to failure by material and workmanship that prove defective within the above period, excluding refrigerant. B. 1st Year Labor Warranty: Entire unit C. Extended Compressor Warranty: None. D. Extended Unit Warranty: Entire unit (no pumps), four (4) years parts and labor. E. Refrigerant Warranty: Five (5) years R410A refrigerant. F. Delay Warranty Start: None MAINTENANCE A. Maintenance of the chillers shall be the responsibility of the owner and performed in accordance with the manufacturer s instructions. PART 2: PRODUCTS Job Name: BAYVIEW SENIOR CENTER 19 of 25

17 Specification for ACC ACCEPTABLE MANUFACTURERS A. Daikin Applied B. (Approved Equal) 2.02 UNIT DESCRIPTION A. Provide and install as shown on the plans factory-assembled, factory-charged air-cooled scroll compressor packaged chillers in the quantity specified. Each chiller shall consist of hermetic tandem scroll compressor sets (total four compressors), brazed plate evaporator, air-cooled condenser section, microprocessor-based control system and all components necessary for controlled unit operation. B. Chiller shall be functionally tested at the factory to ensure trouble free field operation 2.03 DESIGN REQUIREMENTS A. Flow Range: The chiller shall have the ability to support variable flow range down to 40% of nominal design (based on AHRI conditions). B. Operating Range: The chiller shall have the ability to control leaving chilled fluid temperature from 15F to 65F. C. General: Provide a complete scroll compressor packaged chiller as specified herein and as shown on the drawings. The unit shall be in accordance with the standards referenced in section 1.02 and any local codes in effect. D. Performance: Refer to the schedule of performance on the drawings. The chiller shall be capable of stable operation to a minimum percentage of full load (without hot gas bypass) of 25%. Performance shall be in accordance with AHRI Standard 550/590. E. Acoustics: Sound pressure levels for the unit shall not exceed the following specified levels. All manufacturers shall provide the necessary sound treatment ( parts and labor) to meet these levels if required. Sound data shall be provided with the quotation. Test shall be in accordance with AHRI Standard CHILLER COMPONENTS A. Compressor 1. The compressors shall be sealed hermetic, scroll type with crankcase oil heater and suction strainer. The compressor motor shall be refrigerant gas cooled, high torque, hermetic induction type, two-pole, with inherent thermal protection on all three phases and shall be mounted on RIS vibration isolator pads. The compressors shall be equipped with an internal module providing compressor protection and communication capability. B. Evaporator 1. The evaporator shall be a compact, high efficiency, dual circuit, brazed plate-to-plate type heat exchanger consisting of parallel stainless steel plates. 2. The evaporator shall be protected with an external, electric resistance heater plate and insulated with 3/4" (19mm) thick closed-cell polyurethane insulation. This combination shall provide freeze protection down to -20 F (-29 C) ambient air temperature. 3. The water-side maximum design pressure shall be rated at a minimum of 653 psig (4502 kpa). Evaporators shall be designed and constructed according to, and listed by Underwriters Laboratories (UL). C. Condenser Job Name: BAYVIEW SENIOR CENTER 20 of 25

18 Specification for ACC-1 1. Condenser fans shall be propeller type arranged for vertical air discharge and individually driven by direct-drive fan motors. The fans shall be equipped with a heavy-gauge vinyl-coated fan guard. Fan motors shall be TEAO type with permanently lubricated ball bearings, inherent overload protection, three-phase, direct-drive, 1140 rpm. Each fan section shall be partitioned to avoid cross circulation. 2. Coil shall be microchannel design and shall have a series of flat tubes containing multiple, parallel flow microchannels layered between the refrigerant manifolds. Tubes shall be 9153 aluminum alloy. Tubes made of 3102 alloy or other alloys of lower corrosion resistance shall not be accepted. Coils shall consist of a two-pass arrangement. Each condenser coil shall be factory leak tested with high-pressure air under water. Condenser coils shall include baked epoxy coating providing hour salt spray resistance (ASTM B117-90) applied to both the coil and the coil frames. D. Refrigerant Circuit 1. Each of the two refrigerant circuits shall include a replaceable-core refrigerant filter-drier, sight glass with moisture indicator, liquid line solenoid valve (no exceptions), expansion valve, and insulated suction line. E. Construction 1. Unit casing and all structural members and rails shall be fabricated of pre-painted or galvanized steel. Painted parts shall be able to meet ASTM B117, 1000-hour salt spray test. 2. Upper condenser coil section of unit shall have protective, 12 GA, PVC-coated, wire grille guards. F. Control System 1. A centrally located weatherproof control panel shall contain the field power connection points, control interlock terminals, and control system. Box shall be designed in accordance with NEMA 3R rating. Power and starting components shall include factory circuit breaker for fan motors and control circuit, individual contactors for each fan motor, solid-state compressor three-phase motor overload protection, inherent fan motor overload protection and two power blocks (one per circuit) for connection to remote, contractor supplied disconnect switches. Hinged access doors shall be lockable. Barrier panels or separate enclosures are required to protect against accidental contact with line voltage when accessing the control system. 2. Shall include optional single-point connection to a non-fused disconnect switch with through-the-door handle and compressor circuit breakers. G. Unit Controller 1. An advanced DDC microprocessor unit controller with a 5-line by 22-character liquid crystal display provides the operating and protection functions. The controller shall take preemptive limiting action in case of high discharge pressure or low evaporator pressure. The controller shall contain the following features as a minimum: 2. The unit shall be protected in two ways: (1) by alarms that shut the unit down and require manual reset to restore unit operation and (2) by limit alarms that reduce unit operation in response to some out-of-limit condition. Shut down alarms shall activate an alarm signal. 3. Shutdown Alarms a. No evaporator water flow (auto-restart) b. Sensor failures c. Low evaporator pressure d. Evaporator freeze protection e. High condenser pressure f. Outside ambient temperature (auto-restart) g. Motor protection system h. Phase voltage protection (Optional) 4. Limit Alarms a. Condenser pressure stage down, unloads unit at high discharge pressures. b. Low ambient lockout, shuts off unit at low ambient temperatures. c. Low evaporator pressure hold, holds stage #1 until pressure rises. d. Low evaporator pressure unload, shuts off one compressor. 5. Unit Enable Section Job Name: BAYVIEW SENIOR CENTER 21 of 25

19 Specification for ACC-1 a. Enables unit operation from either local keypad, digital input, or BAS 6. Unit Mode Selection a. Selects standard cooling, ice, glycol, or test operation mode 7. Analog Inputs: a. Reset of leaving water temperature, 4-20 ma\ b. Current Limit 8. Digital Inputs a. Unit off switch b. Remote start/stop c. Flow switch d. Ice mode switch, converts operation and setpoints for ice production e. Motor protection 9. Digital Outputs a. Shutdown alarm; field wired, activates on an alarm condition, off when alarm is cleared b. Evaporator pump; field wired, starts pump when unit is set to start 10. Condenser fan control - The unit controller shall provide control of condenser fans based on compressor discharge pressure. 11. Building Automation System (BAS) Interface a. Factory mounted DDC controller(s) shall support operation on a BACnet, Modbus or LONMARK network via one of the data link / physical layers listed below as specified by the successful Building Automation System (BAS) supplier. b. BACnet MS/TP master (Clause 9) c. BACnet IP, (Annex J) d. BACnet ISO , (Ethernet) e. LONMARK FTT-10A. The unit controller shall be LONMARK certified. f. The information communicated between the BAS and the factory mounted unit controllers shall include the reading and writing of data to allow unit monitoring, control and alarm notification as specified in the unit sequence of operation and the unit points list. g. For chillers communicating over a LONMARK network, the corresponding LONMARK external Interface File (XIF) shall be provided with the chiller submittal data. h. All communication from the chiller unit controller as specified in the points list shall be via standard BACnet objects. Proprietary BACnet objects shall not be allowed. BACnet communications shall conform to the BACnet protocol (ANSI/ASHRAE ). A BACnet Protocol Implementation Conformance Statement (PICS) shall be provided along with the unit submittal OPTIONS AND ACCESSORIES A. The following options are to be included: 1. CLOUD-ENABLED EQUIPMENT a. SYSTEM DESCRIPTION: The manufacturer shall provide an equipment management solution, which is factoryinstalled on the HVAC unit. Equipment hardware shall include integrated equipment power measurement and consist of all components necessary to deliver unit controller and power data directly to the cloud. The subscription-based Software as a Service (SaaS) shall allow remote HVAC monitoring, remote HVAC control, preventative maintenance recommendations, and unit commissioning/re-commissioning capabilities using secure, cloud-communicating hardware. The solution shall be capable of communicating to a user device (smart phone, tablet, etc.) via both wireless (cellular, Wi-Fi) and local area network (LAN) connection. All data is stored in the cloud for a minimum of 2 years. b. CLOUD-COMMUNICATING SMART DEVICE: 1) A factory-installed, tested and commissioned cloudcommunicating smart device shall deliver data to the cloud via wireless (Wi-Fi, cellular) or local area network (LAN) connection. 2) The cloud-communicating smart device shall implement security, to include: Job Name: BAYVIEW SENIOR CENTER 22 of 25

20 Specification for ACC-1 PART 3: EXECUTION c. Data delivery via secure HTTPS using SSL d. Virus and Malware protection e. Boot-level security f. Compliance: g. CE h. FCC Class A/Industry Canada i. UL60950 Carrier Approved j. INTEGRATED POWER METER: A factory-installed, tested and commissioned power meter shall monitor unit voltage, current, and power and transmit this data to the cloud-communicating smart device, for delivery to the cloud or shall deliver directly to the cloud. Hardware shall: k. Allow monitoring of single-phase, split-phase and 3-phase Y & Delta connections up to 600VAC (45-65 Hz) and up to 1000A l. Be UL /CSA C22.2 No and UL/CSA UL recognized 2. Low Ambient Control: Fan VFD allows unit operation from 32 F down to -10 F (-23.3 C). 3. Ground Fault Protection: Factory installed circuit breaker to protect equipment from damage from line-toground fault currents less than those required for conductor protection. 4. Phase loss with under/over voltage protection and with LED indication of the fault type to guard against compressor motor burnout. 5. The following accessories, if selected, are to be included: a. Spring vibration isolators for field installation b. Rubber-in-shear vibration isolators for field installation c. Factory-mounted thermal dispersion type flow switch d. Field-mounted, paddle type, chilled water flow switch field wired to the control panel e. Wye strainer, to be installed at the evaporator inlet and sized for the design flow rate, with perforation diameter of 0.063" with blowdown valve and Victaulic couplings (factory mounted or field installed) f. 115V GFI convenience outlet B. Optional Factory-Installed Pump Package: None 1. These pump package accessories, if selected, will also be included: a. Water pressure gauges on the pump suction and discharge b. Expansion tank with size increments from 4.4 to 90 gallons, field installed (small sizes can be factory mounted c. Air separator with air vent, field installed d. Storage tanks, vertical, insulated, 150, 300, 600, 1000 gallon sizes with optional immersion heater, field installed INSTALLATION A. Antenna, or equivalent, if needed, shall be shipped loose from the factory, and shall be mounted and electricallyconnected in the field by the contractor providing unit start-up and commissioning, per factory-supplied installation literature. For sites using Local Area Network (LAN) connection to provide cloud access, appropriate trades should coordinate to supply all necessary roof penetrations, conduit, network cable, network infrastructure, and termination to the network B. Install in strict accordance with manufacturer s requirements, shop drawings, and contract documents. C. Adjust and level chiller in alignment on supports. D. Coordinate electrical installation with electrical contractor. E. Coordinate controls with control contractor. F. Install a field-supplied or optional manufacturer-supplied strainer in the chilled water return line at the evaporator inlet that meets manufacturer perforation size specifications. Job Name: BAYVIEW SENIOR CENTER 23 of 25

21 Specification for ACC START-UP A. Initial programming of cloud-communicating smart device and integrated power meter shall be performed at the factory. Commissioning technician will submit the startup and commission documentation through the User Interface. B. Provide testing and starting of machine, and instruct the Owner in its proper operation and maintenance. Job Name: BAYVIEW SENIOR CENTER 24 of 25